| Thu, 13 Apr 2023 09:35:43 +0200 |
heinrichsweikamp |
1.6.2 release
|
| Wed, 12 Apr 2023 09:56:00 +0200 |
heinrichsweikamp |
Update build for testing
|
| Wed, 12 Apr 2023 09:30:15 +0200 |
heinrichsweikamp |
change button default responsiveness to 100
|
| Wed, 12 Apr 2023 09:24:44 +0200 |
heinrichsweikamp |
After a firmware update, use the factory settings for button sensitivity if these exist, the default settings otherwise.
|
| Mon, 27 Mar 2023 10:04:53 +0200 |
heinrichsweikamp |
Update build for testing
|
| Sun, 26 Mar 2023 18:34:30 +0200 |
heinrichsweikamp |
increase HAL_Delay to 10ms for cold-start-button reset
|
| Sun, 26 Mar 2023 11:27:29 +0200 |
heinrichsweikamp |
Preparing a 1.6.2 release candidate
|
| Tue, 21 Mar 2023 12:57:37 +0100 |
heinrichsweikamp |
Fix/handle negative scrubber timer values
|
| Tue, 21 Mar 2023 12:56:54 +0100 |
heinrichsweikamp |
Quit simualted dives after the dive time set in the SIM tab.
|
| Fri, 17 Mar 2023 09:35:25 +0100 |
heinrichsweikamp |
Some compass improvements from mikeller
|
| Wed, 15 Mar 2023 09:18:07 +0100 |
heinrichsweikamp |
- Colours for scrubber display when time remaining falls below a threshold value
|
| Tue, 07 Mar 2023 22:14:20 +0100 |
Ideenmodellierer |
Dev Bugfix: ignore analog out of bounds limits for DiveO2 sensor:
|
| Tue, 07 Mar 2023 20:02:05 +0100 |
Ideenmodellierer |
Added visualization of CO2 during dive:
|
| Tue, 07 Mar 2023 19:59:02 +0100 |
Ideenmodellierer |
Cleanup display of multiple warnings in T3 (Big font) view:
|
| Tue, 07 Mar 2023 19:55:13 +0100 |
Ideenmodellierer |
Only show autodetection in sensor menu if external interface is present:
|
| Tue, 07 Mar 2023 19:52:18 +0100 |
Ideenmodellierer |
Updated outdated comment
|
| Tue, 07 Mar 2023 19:51:30 +0100 |
Ideenmodellierer |
Dev Bugfix: Alignment problem in lifedata structure:
|
| Mon, 13 Mar 2023 22:23:00 +0100 |
Ideenmodellierer |
resolv merge
|
| Sun, 05 Mar 2023 22:17:32 +0100 |
Ideenmodellierer |
Avoid blinking in customer view selection page:
|
| Mon, 13 Mar 2023 22:18:28 +0100 |
Ideenmodellierer |
Added enum for Co2 display
|
| Sun, 05 Mar 2023 22:14:53 +0100 |
Ideenmodellierer |
Added display of co2 ppm values:
|
| Sun, 05 Mar 2023 22:06:47 +0100 |
Ideenmodellierer |
Added pressure compensation to CO2 detection:
|
| Tue, 21 Feb 2023 21:19:31 +0100 |
Ideenmodellierer |
Code cleanup sensors under development:
|
| Sun, 19 Feb 2023 21:52:02 +0100 |
Ideenmodellierer |
Update Sentinel protocol:
|
| Sun, 19 Feb 2023 21:51:19 +0100 |
Ideenmodellierer |
Added DiveO2 fatal error detection:
|
| Sun, 19 Feb 2023 21:48:47 +0100 |
Ideenmodellierer |
Enable start dive in Big font display:
|
| Sun, 19 Feb 2023 21:43:24 +0100 |
Ideenmodellierer |
Update Sentinel protocol:
|
| Thu, 02 Feb 2023 17:35:54 +0100 |
Ideenmodellierer |
Added button lock after wakeup in surface mode:
|
| Thu, 02 Feb 2023 17:35:38 +0100 |
Ideenmodellierer |
Added button lock after wakeup in surface mode:
|
| Thu, 02 Feb 2023 17:26:54 +0100 |
Ideenmodellierer |
Enable start dive in Big font display:
|
| Thu, 02 Feb 2023 17:19:24 +0100 |
Ideenmodellierer |
Added data init function for external interface:
|
| Mon, 06 Mar 2023 16:03:00 +0100 |
heinrichsweikamp |
NEW: Add mini compass with marker declination indication
|
| Fri, 03 Mar 2023 10:41:44 +0100 |
heinrichsweikamp |
Fixed logbook download after switch from CCR to extra (OC) gas if the extra gas
|
| Tue, 14 Feb 2023 10:21:56 +0100 |
heinrichsweikamp |
Fixed invalid setpoint (0.0) used after switch from CCR to extra (OC) gas
|
| Sun, 15 Jan 2023 21:51:54 +0100 |
Ideenmodellierer |
Removed interface selection from sensor menu:
|
| Sun, 15 Jan 2023 21:48:34 +0100 |
Ideenmodellierer |
Optical sensor as default:
|
| Sun, 15 Jan 2023 21:45:14 +0100 |
Ideenmodellierer |
Fix compiler switch:
|
| Sun, 15 Jan 2023 21:43:33 +0100 |
Ideenmodellierer |
Improvment sensor Autodetection:
|
| Sat, 14 Jan 2023 20:49:40 +0100 |
Ideenmodellierer |
Update sensor menu support for automatic sensor detection:
|
| Sat, 14 Jan 2023 20:46:17 +0100 |
Ideenmodellierer |
Added auto detection functionality for sensors connected to the external interface:
|
| Sat, 14 Jan 2023 20:41:36 +0100 |
Ideenmodellierer |
Added sensor map to Firmware <=> RTE inferface:
|
| Sat, 14 Jan 2023 20:37:20 +0100 |
Ideenmodellierer |
Enabled CO2 support for beta test phase:
|
| Sat, 14 Jan 2023 20:35:40 +0100 |
Ideenmodellierer |
Bugfix data synchronization after RTE start:
|
| Sat, 07 Jan 2023 18:11:52 +0100 |
Ideenmodellierer |
Update CO2 sensor implementation:
|
| Thu, 05 Jan 2023 18:30:06 +0100 |
Ideenmodellierer |
Development feature: external pressure sensor
|
| Thu, 05 Jan 2023 18:27:04 +0100 |
Ideenmodellierer |
DigO2 added raw data request:
|
| Thu, 05 Jan 2023 18:25:47 +0100 |
Ideenmodellierer |
Show saturation in large font (T3) view:
|
| Thu, 05 Jan 2023 18:22:21 +0100 |
Ideenmodellierer |
DigO2 added raw data request:
|
| Tue, 03 Jan 2023 19:47:12 +0100 |
Ideenmodellierer |
Bugfix set date (year):
|
| Sun, 27 Nov 2022 15:18:00 +0100 |
heinrichsweikamp |
Add build for 1.6.1 beta / RTE 2.9 (Support for DiveO2 solid state oxygen sensors)
|
| Sun, 20 Nov 2022 20:49:41 +0100 |
Ideenmodellierer |
Updated menu structure to support new sensor information page:
|
| Sun, 20 Nov 2022 20:46:10 +0100 |
Ideenmodellierer |
Added new info page for extended sensor data:
|
| Sun, 20 Nov 2022 20:43:04 +0100 |
Ideenmodellierer |
Added customizable data area for specific sensor data:
|
| Sun, 20 Nov 2022 20:42:33 +0100 |
Ideenmodellierer |
Increased version number and set beta label
|
| Sun, 20 Nov 2022 20:42:08 +0100 |
Ideenmodellierer |
Added customizable data area for specific sensor data:
|
| Sun, 20 Nov 2022 20:37:44 +0100 |
Ideenmodellierer |
Increased version number and set beta label
|
| Sun, 20 Nov 2022 20:36:34 +0100 |
Ideenmodellierer |
Bugfix PSCR menu button label:
|
| Tue, 08 Nov 2022 22:16:56 +0100 |
Ideenmodellierer |
Development bugfix number of spare bytes in setting structure
|
| Tue, 08 Nov 2022 21:16:17 +0100 |
Ideenmodellierer |
Extension scrubber time:
|
| Tue, 08 Nov 2022 21:13:14 +0100 |
Ideenmodellierer |
Bugfix compass bearing:
|
| Thu, 03 Nov 2022 20:44:51 +0100 |
Ideenmodellierer |
Menu cleanup rebreather specific settings:
|
| Thu, 03 Nov 2022 20:44:21 +0100 |
Ideenmodellierer |
Menu cleanup rebreather specific settings:
|
| Thu, 03 Nov 2022 20:37:06 +0100 |
Ideenmodellierer |
Bugfix: only reset menu if a new sub menu is created:
|
| Tue, 01 Nov 2022 09:55:45 +0100 |
Ideenmodellierer |
Bugfix release frame:
|
| Fri, 28 Oct 2022 20:49:21 +0200 |
Ideenmodellierer |
Added protocol functions for UART DiveO2 sensor:
|
| Fri, 28 Oct 2022 20:32:24 +0200 |
Ideenmodellierer |
Added selection of digital o2 sensor source to HW menu:
|
| Fri, 28 Oct 2022 20:29:37 +0200 |
Ideenmodellierer |
Added digital o2 sensor to settings and data exchange:
|
| Fri, 28 Oct 2022 19:39:20 +0200 |
Ideenmodellierer |
Bugfix display of deactivated sensors:
|
| Tue, 18 Oct 2022 21:21:32 +0200 |
Ideenmodellierer |
Bugfix motioncontrol frame deactivation:
|
| Tue, 18 Oct 2022 20:56:19 +0200 |
Ideenmodellierer |
Cleanup warnings:
|
| Sun, 25 Sep 2022 21:13:45 +0200 |
Ideenmodellierer |
Bugfix Empty menu:
|
| Sun, 25 Sep 2022 21:09:18 +0200 |
Ideenmodellierer |
Improvment key event detection:
|
| Fri, 19 Aug 2022 11:30:24 +0200 |
heinrichsweikamp |
Merge
|
| Fri, 19 Aug 2022 11:27:44 +0200 |
heinrichsweikamp |
1.6.0 release
Betatest
|
| Sat, 06 Aug 2022 11:10:56 +0200 |
heinrichsweikamp |
Update current build for testing
Betatest
|
| Fri, 05 Aug 2022 16:04:52 +0200 |
Ideenmodellierer |
Improvment charge percent visualization:
Betatest
|
| Fri, 05 Aug 2022 15:27:01 +0200 |
Ideenmodellierer |
Added compile switch for Sentinel rebreather option
Betatest
|
| Fri, 05 Aug 2022 15:26:28 +0200 |
Ideenmodellierer |
Improvment external interface usage:
Betatest
|
| Fri, 05 Aug 2022 15:22:26 +0200 |
Ideenmodellierer |
Added Sentinel protocoll support:
Betatest
|
| Fri, 05 Aug 2022 15:15:01 +0200 |
Ideenmodellierer |
Added Sentinel as O2 sensor source:
Betatest
|
| Fri, 05 Aug 2022 15:13:29 +0200 |
Ideenmodellierer |
Added sanity check for temperature and pressure values:
Betatest
|
| Fri, 05 Aug 2022 15:10:10 +0200 |
Ideenmodellierer |
Increased version numbers:
Betatest
|
| Fri, 05 Aug 2022 14:56:17 +0200 |
Ideenmodellierer |
Bugfix Battery charge complete event:
Betatest
|
| Wed, 03 Aug 2022 18:19:03 +0200 |
Ideenmodellierer |
Bugfix automatic switch to o2 sensor custom view:
Betatest
|
| Thu, 02 Jun 2022 20:24:59 +0200 |
Ideenmodellierer |
Ignore automatic setpoint changes during ascend:
Betatest
|
| Mon, 16 May 2022 20:50:26 +0200 |
Ideenmodellierer |
Bugfix: Set actual gas after basic dive settings were created:
Betatest
|
| Mon, 25 Apr 2022 21:15:01 +0200 |
Ideenmodellierer |
Bugfix low ppO2 warning in bailout mode:
Betatest
|
| Mon, 25 Apr 2022 21:10:10 +0200 |
Ideenmodellierer |
Bugfix screen clipping (Flipdisplay mode):
Betatest
|
| Mon, 25 Apr 2022 21:07:28 +0200 |
Ideenmodellierer |
Bugfix visualization better setpoint:
Betatest
|
| Fri, 22 Apr 2022 18:24:43 +0200 |
Jan Mulder |
cleanup: Use correct "per" symbol
Betatest
|
| Thu, 21 Apr 2022 21:02:50 +0200 |
Jan Mulder |
Bugfix: deco planner did not initialize properly
Betatest
|
| Wed, 20 Apr 2022 20:25:04 +0200 |
Jan Mulder |
Move include file to common to ...
Betatest
|
| Mon, 22 Nov 2021 19:39:11 +0100 |
Jan Mulder |
Allow longer scrubber time
Betatest
|
| Wed, 30 Mar 2022 18:07:21 +0200 |
Ideenmodellierer |
Bugfix: Missing flip screen support for charge view
Betatest
|
| Wed, 30 Mar 2022 18:01:29 +0200 |
heinrichsweikamp |
Zusammenf?hren
Betatest
|
| Wed, 30 Mar 2022 18:00:21 +0200 |
heinrichsweikamp |
Show 98% in case of Oxygen as the calibrating gas
Betatest
|
| Sat, 12 Mar 2022 23:01:11 +0100 |
Ideenmodellierer |
Added Charging view:
Betatest
|
| Sat, 12 Mar 2022 22:58:22 +0100 |
Ideenmodellierer |
Support of unknown charging counter values:
Betatest
|
| Sat, 12 Mar 2022 22:54:26 +0100 |
Ideenmodellierer |
Reduce display brightness in case the charger is connected:
Betatest
|
| Sat, 12 Mar 2022 22:49:09 +0100 |
Ideenmodellierer |
Rework charge cycle:
Betatest
|
| Sat, 12 Mar 2022 22:48:45 +0100 |
Ideenmodellierer |
Rework charge cycle:
Betatest
|
| Sat, 12 Mar 2022 22:42:56 +0100 |
Ideenmodellierer |
Increased version number
Betatest
|
| Sat, 12 Mar 2022 14:57:54 +0100 |
heinrichsweikamp |
increase version numbers for upcomming release
Betatest
|
| Fri, 24 Dec 2021 13:40:47 +0100 |
heinrichsweikamp |
update test build
Betatest
|
| Tue, 21 Dec 2021 19:36:41 +0100 |
Ideenmodellierer |
Stability improvment bluetooth startup:
Betatest
|
| Tue, 21 Dec 2021 19:32:29 +0100 |
Ideenmodellierer |
Revert Setbluetooh name changes
Betatest
|
| Tue, 14 Dec 2021 15:36:10 +0100 |
heinrichs weikamp |
PSCR Mode
Betatest
|
| Mon, 01 Nov 2021 12:39:34 +0100 |
heinrichs weikamp |
Undo Rev. 660
|
| Sun, 08 Aug 2021 09:36:23 +0200 |
heinrichsweikamp |
Add option to reset bluetooth name
|
| Wed, 28 Apr 2021 09:47:25 +0200 |
heinrichs weikamp |
Update build file for testing
|
| Tue, 27 Apr 2021 21:29:26 +0200 |
Ideenmodellierer |
Bugfix handling of new menu tab in flipped mode:
|
| Mon, 26 Apr 2021 15:03:04 +0200 |
heinrichs weikamp |
Update release date
|
| Sun, 25 Apr 2021 20:47:01 +0200 |
Ideenmodellierer |
Added visualization of scrubber time:
|
| Sun, 25 Apr 2021 20:42:56 +0200 |
Ideenmodellierer |
Added count down timer for scrubber time:
|
| Sun, 25 Apr 2021 20:41:19 +0200 |
Ideenmodellierer |
Introduced new menu tab for addition CCR options:
|
| Sun, 25 Apr 2021 20:36:18 +0200 |
Ideenmodellierer |
Bugfix temperature display Logpage2:
|
| Mon, 19 Apr 2021 20:34:53 +0200 |
Ideenmodellierer |
Allow setpoint starting at 0.4 ppO2:
|
| Mon, 19 Apr 2021 20:20:38 +0200 |
Ideenmodellierer |
Automatik setpoint change:
|
| Mon, 19 Apr 2021 20:19:32 +0200 |
Ideenmodellierer |
Automatik setpoint change:
|
| Mon, 19 Apr 2021 20:16:24 +0200 |
Ideenmodellierer |
Bugfix consider checkbox in calculation of right aligned and centered position:
|
| Mon, 19 Apr 2021 20:14:20 +0200 |
Ideenmodellierer |
Motion detection: Enable focus after focus calibration:
|
| Tue, 13 Apr 2021 19:25:41 +0200 |
Ideenmodellierer |
Integrated selection of bailout in the diluent selection page:
|
| Tue, 13 Apr 2021 19:21:14 +0200 |
Ideenmodellierer |
Remove battery charge counter from information menu:
|
| Tue, 13 Apr 2021 19:18:32 +0200 |
Ideenmodellierer |
Small changes in charger state handling:
|
| Tue, 30 Mar 2021 10:34:12 +0200 |
heinrichs weikamp |
Compile with ENABLE_CHARGER_STATUS_V2
|
| Wed, 24 Mar 2021 22:06:00 +0100 |
Ideenmodellierer |
Reimplemented charger status generation (deactivated):
|
| Wed, 24 Mar 2021 21:28:41 +0100 |
Ideenmodellierer |
Do not show focus indicator in case motion detection is suspended:
|
| Thu, 11 Mar 2021 21:45:22 +0100 |
Ideenmodellierer |
Development Bugfix Deco bars not shown after last deco stop passed:
|
| Thu, 11 Mar 2021 21:43:43 +0100 |
Ideenmodellierer |
Development bugfix Viewport settings:
|
| Thu, 25 Feb 2021 12:20:43 +0100 |
heinrichsweikamp |
add build for testing, advance to FW1.5.7, RTE is unchanged since 1.5.6
|
| Wed, 24 Feb 2021 21:45:35 +0100 |
Ideenmodellierer |
Added last measured PPO2 value to sensor selection dialog:
|
| Wed, 24 Feb 2021 21:04:07 +0100 |
Ideenmodellierer |
Debounce fallback warning:
|
| Wed, 24 Feb 2021 21:03:54 +0100 |
Ideenmodellierer |
Debounce fallback warning:
|
| Wed, 24 Feb 2021 21:03:22 +0100 |
Ideenmodellierer |
Debounce fallback warning:
|
| Wed, 24 Feb 2021 19:18:26 +0100 |
Ideenmodellierer |
Enable sensor check for Analog PPO2 mode:
|
| Tue, 23 Feb 2021 21:58:18 +0100 |
Ideenmodellierer |
Added menu structure to allow ppo2 modification in simulator mode:
|
| Tue, 23 Feb 2021 21:55:52 +0100 |
Ideenmodellierer |
Warnings:
|
| Tue, 23 Feb 2021 21:55:26 +0100 |
Ideenmodellierer |
Warnings:
|
| Tue, 23 Feb 2021 21:54:56 +0100 |
Ideenmodellierer |
Warnings:
|
| Tue, 23 Feb 2021 21:53:24 +0100 |
Ideenmodellierer |
Added functionality to add ppo2 mV offset:
|
| Fri, 12 Feb 2021 21:46:36 +0100 |
Ideenmodellierer |
Added compile switch for T3_PROFILE menu operation option
|
| Fri, 12 Feb 2021 21:43:27 +0100 |
Ideenmodellierer |
Improve in / out of focus transitions:
|
| Fri, 12 Feb 2021 21:37:50 +0100 |
Ideenmodellierer |
Added option to select sensitivity of focus detection:
|
| Mon, 08 Feb 2021 21:35:46 +0100 |
Ideenmodellierer |
Switch Sector / Scroll detection to vector implementation:
|
| Sun, 07 Feb 2021 22:05:32 +0100 |
Ideenmodellierer |
Development bugfix: Marker in standard t3 view drawn in wrong direction
|
| Sun, 07 Feb 2021 22:04:43 +0100 |
Ideenmodellierer |
Improvment frame Handling:
|
| Wed, 03 Feb 2021 21:45:48 +0100 |
Ideenmodellierer |
Adjustments for flipped display view:
|
| Wed, 03 Feb 2021 21:44:22 +0100 |
Ideenmodellierer |
Use roll and pitch agles in 0-360 format:
|
| Wed, 27 Jan 2021 22:12:44 +0100 |
Ideenmodellierer |
Added minilog functions to allow marker synchronisation:
|
| Wed, 27 Jan 2021 22:10:11 +0100 |
Ideenmodellierer |
Added t3 quick menu for marker synchronisation:
|
| Wed, 27 Jan 2021 22:04:45 +0100 |
Ideenmodellierer |
Development bugfix: focus state not remembered:
|
| Wed, 27 Jan 2021 22:03:11 +0100 |
Ideenmodellierer |
Development bugfix: Low battery warning was interpretated as marker:
|
| Wed, 27 Jan 2021 21:58:46 +0100 |
Ideenmodellierer |
Development bugfix: show replay symbol only for the selected dive:
|
| Wed, 27 Jan 2021 21:56:48 +0100 |
Ideenmodellierer |
Moved non critical functions from timer interrupt to main loop:
|
| Wed, 20 Jan 2021 20:05:05 +0100 |
Ideenmodellierer |
Added "Set Marker" to T3 quick menu:
|
| Fri, 15 Jan 2021 21:33:07 +0100 |
Ideenmodellierer |
Added "Set Marker" to T3 quick menu:
|
| Fri, 15 Jan 2021 21:20:29 +0100 |
Ideenmodellierer |
Bugfix inverted whitspace:
|
| Thu, 14 Jan 2021 21:25:15 +0100 |
Ideenmodellierer |
Suspend MotionDetection events while diver is operationg the OSTC:
|
| Thu, 14 Jan 2021 20:38:28 +0100 |
Ideenmodellierer |
Added access to logbook marker data:
|
| Thu, 14 Jan 2021 19:17:28 +0100 |
Ideenmodellierer |
Bugfix: CalibViewport were shown even in case the compile switch had not been set:
|
| Fri, 05 Feb 2021 14:53:50 +0100 |
heinrichsweikamp |
Update RTE required value for release
|
| Fri, 05 Feb 2021 14:50:18 +0100 |
heinrichsweikamp |
Added tag v1.5.6 release for changeset 06ec1da5e105
|
| Fri, 05 Feb 2021 14:50:05 +0100 |
heinrichsweikamp |
1.5.6 release
v1.5.6 release
|
| Thu, 07 Jan 2021 09:53:04 +0100 |
heinrichsweikamp |
change O2_CALIB_FRACTION_O2 to 0.98
|
| Wed, 06 Jan 2021 21:01:00 +0100 |
Ideenmodellierer |
Merged menu items of viewport and motion control:
|
| Wed, 06 Jan 2021 19:41:43 +0100 |
Ideenmodellierer |
T3 profile view: Added visualization of deco data
|
| Tue, 05 Jan 2021 20:35:01 +0100 |
Ideenmodellierer |
Added replay data scaling in case life data is longer than replay block
|
| Mon, 04 Jan 2021 22:49:07 +0100 |
Ideenmodellierer |
Bugfix T3 skip deactivated views:
|
| Mon, 04 Jan 2021 22:45:37 +0100 |
Ideenmodellierer |
Added compile switch for new T3 View Profile
|
| Mon, 04 Jan 2021 21:48:31 +0100 |
Ideenmodellierer |
Bugfix T3 skip deactivated views:
|
| Mon, 04 Jan 2021 21:41:51 +0100 |
Ideenmodellierer |
New replay block for T3 profile:
|
| Mon, 04 Jan 2021 21:38:28 +0100 |
Ideenmodellierer |
MotionControl-Sector: Map sectors during switch T7 <=> T3:
|
| Mon, 04 Jan 2021 21:35:38 +0100 |
Ideenmodellierer |
Added functionality to select a dive to be shown in the T3 profile view:
|
| Mon, 04 Jan 2021 21:32:39 +0100 |
Ideenmodellierer |
Bugfix Selection of primary view:
|
| Mon, 04 Jan 2021 21:30:04 +0100 |
Ideenmodellierer |
Added compile switch for new T3 View Profile
|
| Mon, 04 Jan 2021 21:24:24 +0100 |
Ideenmodellierer |
Added PrintGraph option to skip invalid data entries:
|
| Sun, 03 Jan 2021 14:43:16 +0100 |
Ideenmodellierer |
MotionCtrl - Sectorview Map sectors directly to custom views:
|
| Wed, 06 Jan 2021 22:02:49 +0100 |
heinrichsweikamp |
Minor: Comment translation into English
|
| Tue, 22 Dec 2020 22:23:11 +0100 |
Ideenmodellierer |
Align VPM tag in log list to be at same position as GF tag:
|
| Thu, 17 Dec 2020 10:58:28 +0100 |
heinrichsweikamp |
Minor: Update the documentation for building the code
|
| Thu, 17 Dec 2020 09:52:12 +0100 |
heinrichsweikamp |
Update current build, "RTErequired" value and release date
|
| Wed, 16 Dec 2020 09:43:11 +0100 |
heinrichsweikamp |
update ostc4pack sample files
|
| Sun, 13 Dec 2020 18:31:40 +0100 |
Ideenmodellierer |
Motion control: Jump back to primary view if focus is lost:
|
| Sun, 13 Dec 2020 18:29:12 +0100 |
Ideenmodellierer |
Reduced view angle and number of vusiualized custom views in setor mode:
|
| Sat, 12 Dec 2020 21:05:11 +0100 |
Ideenmodellierer |
Added option for 100% o2 calibration:
|
| Sat, 12 Dec 2020 20:54:31 +0100 |
Ideenmodellierer |
Solved minor warnings
|
| Sat, 12 Dec 2020 20:52:58 +0100 |
Ideenmodellierer |
Show Fallback if no valid sensor value is available:
|
| Sat, 12 Dec 2020 19:18:57 +0100 |
Ideenmodellierer |
Added ex Interface measurement restart in case of i2c disturbance:
|
| Sat, 12 Dec 2020 19:16:37 +0100 |
Ideenmodellierer |
Bugfix bad resolution of compass LSM303AGR:
|
| Thu, 03 Dec 2020 13:17:32 +0100 |
heinrichsweikamp |
Minor: Functional inert cleanup of some unused variables
|
| Sun, 29 Nov 2020 23:02:11 +0100 |
Ideenmodellierer |
Rework pitch detection:
|
| Sun, 29 Nov 2020 22:58:11 +0100 |
Ideenmodellierer |
Handle o2 voltage values < 0.5mV as invalid:
|
| Sun, 29 Nov 2020 22:55:31 +0100 |
Ideenmodellierer |
Return to o2 values:
|
| Sun, 29 Nov 2020 22:53:33 +0100 |
Ideenmodellierer |
Change style of viewport calibration menu:
|
| Wed, 25 Nov 2020 20:26:01 +0100 |
Ideenmodellierer |
Improved focus detection:
|
| Wed, 25 Nov 2020 20:19:50 +0100 |
Ideenmodellierer |
Update String "Blickwinkel":
|
| Wed, 25 Nov 2020 20:18:22 +0100 |
Ideenmodellierer |
Added debug view to viewport calibration:
|
| Wed, 25 Nov 2020 20:16:20 +0100 |
Ideenmodellierer |
Reactivate compass parameter stored in NVM:
|
| Mon, 30 Nov 2020 20:55:23 +0100 |
Ideenmodellierer |
Try to reduce legth of log entry string:
|
| Mon, 30 Nov 2020 20:52:49 +0100 |
Ideenmodellierer |
Added new section "lower.font":
|
| Sun, 29 Nov 2020 11:41:03 +0100 |
heinrichsweikamp |
Minor: Update the documentation for building the code
|
| Tue, 24 Nov 2020 13:22:23 -0600 |
izzni |
-Add 12HR Time Support
|
| Sat, 21 Nov 2020 17:41:59 +0100 |
heinrichsweikamp |
add current build
|
| Sun, 15 Nov 2020 20:12:19 +0100 |
Ideenmodellierer |
Bugfix center / right alignment if dualfont is used:
|
| Sun, 15 Nov 2020 20:09:31 +0100 |
Ideenmodellierer |
Bugfix One or more deactivated sensors hide sensor display:
|
| Sun, 15 Nov 2020 20:01:56 +0100 |
Ideenmodellierer |
Refine o2 sensor diagnostic functions:
|
| Sun, 15 Nov 2020 19:58:14 +0100 |
Ideenmodellierer |
Added ADC sensor interface to O2 sensore menu structure:
|
| Sun, 15 Nov 2020 19:54:36 +0100 |
Ideenmodellierer |
Solved minor warnings
|
| Sun, 15 Nov 2020 19:53:09 +0100 |
Ideenmodellierer |
Added O2 sensor source and calibration parameters to setting structure
|
| Sun, 15 Nov 2020 19:52:03 +0100 |
Ideenmodellierer |
Check if HW evaluation was performed:
|
| Thu, 12 Nov 2020 20:06:04 +0100 |
Ideenmodellierer |
Changed operation mode of RecoverSampleIndex:
|
| Thu, 12 Nov 2020 20:03:00 +0100 |
Ideenmodellierer |
Stabilityfix: Do not trust lastDiveLogID == 0 at startup:
|
| Thu, 12 Nov 2020 19:54:58 +0100 |
Ideenmodellierer |
Switch source of o2 sensor data depending on availability of external ADC:
|
| Thu, 12 Nov 2020 19:48:28 +0100 |
Ideenmodellierer |
Added HW_Info to Discovery <=> RTE data exchange:
|
| Thu, 12 Nov 2020 19:46:03 +0100 |
Ideenmodellierer |
Added external ADC interface functionality (MCP3424):
|
| Sun, 08 Nov 2020 18:49:54 +0100 |
Ideenmodellierer |
Added color indicator for focus state:
|
| Sun, 08 Nov 2020 18:46:46 +0100 |
Ideenmodellierer |
Added menu structure to acces viewport calibration:
|
| Sun, 08 Nov 2020 18:43:19 +0100 |
Ideenmodellierer |
Added viewport functionality:
|
| Sun, 08 Nov 2020 18:38:53 +0100 |
Ideenmodellierer |
Make sure motion detection settings are set to default values:
|
| Sun, 08 Nov 2020 18:36:02 +0100 |
Ideenmodellierer |
Only execute motion detection functions if features is enabled:
|
| Sun, 08 Nov 2020 16:38:43 +0100 |
Ideenmodellierer |
Update roll and pitch value in simulation mode:
|
| Mon, 02 Nov 2020 21:17:45 +0100 |
Ideenmodellierer |
Added viewport calibration to dive menu:
|
| Mon, 02 Nov 2020 21:15:42 +0100 |
Ideenmodellierer |
Added new settings for Viewport:
|
| Tue, 03 Nov 2020 12:47:51 +0100 |
heinrichsweikamp |
Add I2C address for external bulkhead ADC (Hardware gen 3 only) to i2c.h
|
