Mercurial > public > ostc4
graph
-
1.6.2 releaseThu, 13 Apr 2023 09:35:43 +0200, by heinrichsweikamp
-
Update build for testingWed, 12 Apr 2023 09:56:00 +0200, by heinrichsweikamp
-
change button default responsiveness to 100Wed, 12 Apr 2023 09:30:15 +0200, by heinrichsweikamp
-
After a firmware update, use the factory settings for button sensitivity if these exist, the default settings otherwise.Wed, 12 Apr 2023 09:24:44 +0200, by heinrichsweikamp
-
Update build for testingMon, 27 Mar 2023 10:04:53 +0200, by heinrichsweikamp
-
increase HAL_Delay to 10ms for cold-start-button resetSun, 26 Mar 2023 18:34:30 +0200, by heinrichsweikamp
-
Preparing a 1.6.2 release candidateSun, 26 Mar 2023 11:27:29 +0200, by heinrichsweikamp
-
Fix/handle negative scrubber timer valuesTue, 21 Mar 2023 12:57:37 +0100, by heinrichsweikamp
-
Quit simualted dives after the dive time set in the SIM tab.Tue, 21 Mar 2023 12:56:54 +0100, by heinrichsweikamp
-
Some compass improvements from mikellerFri, 17 Mar 2023 09:35:25 +0100, by heinrichsweikamp
-
- Colours for scrubber display when time remaining falls below a threshold valueWed, 15 Mar 2023 09:18:07 +0100, by heinrichsweikamp
-
Dev Bugfix: ignore analog out of bounds limits for DiveO2 sensor:Tue, 07 Mar 2023 22:14:20 +0100, by Ideenmodellierer
-
Added visualization of CO2 during dive:Tue, 07 Mar 2023 20:02:05 +0100, by Ideenmodellierer
-
Cleanup display of multiple warnings in T3 (Big font) view:Tue, 07 Mar 2023 19:59:02 +0100, by Ideenmodellierer
-
Only show autodetection in sensor menu if external interface is present:Tue, 07 Mar 2023 19:55:13 +0100, by Ideenmodellierer
-
Updated outdated commentTue, 07 Mar 2023 19:52:18 +0100, by Ideenmodellierer
-
Dev Bugfix: Alignment problem in lifedata structure:Tue, 07 Mar 2023 19:51:30 +0100, by Ideenmodellierer
-
resolv mergeMon, 13 Mar 2023 22:23:00 +0100, by Ideenmodellierer
-
Avoid blinking in customer view selection page:Sun, 05 Mar 2023 22:17:32 +0100, by Ideenmodellierer
-
Added enum for Co2 displayMon, 13 Mar 2023 22:18:28 +0100, by Ideenmodellierer
-
Added display of co2 ppm values:Sun, 05 Mar 2023 22:14:53 +0100, by Ideenmodellierer
-
Added pressure compensation to CO2 detection:Sun, 05 Mar 2023 22:06:47 +0100, by Ideenmodellierer
-
Code cleanup sensors under development:Tue, 21 Feb 2023 21:19:31 +0100, by Ideenmodellierer
-
Update Sentinel protocol:Sun, 19 Feb 2023 21:52:02 +0100, by Ideenmodellierer
-
Added DiveO2 fatal error detection:Sun, 19 Feb 2023 21:51:19 +0100, by Ideenmodellierer
-
Enable start dive in Big font display:Sun, 19 Feb 2023 21:48:47 +0100, by Ideenmodellierer
-
Update Sentinel protocol:Sun, 19 Feb 2023 21:43:24 +0100, by Ideenmodellierer
-
Added button lock after wakeup in surface mode:Thu, 02 Feb 2023 17:35:54 +0100, by Ideenmodellierer
-
Added button lock after wakeup in surface mode:Thu, 02 Feb 2023 17:35:38 +0100, by Ideenmodellierer
-
Enable start dive in Big font display:Thu, 02 Feb 2023 17:26:54 +0100, by Ideenmodellierer
-
Added data init function for external interface:Thu, 02 Feb 2023 17:19:24 +0100, by Ideenmodellierer
-
NEW: Add mini compass with marker declination indicationMon, 06 Mar 2023 16:03:00 +0100, by heinrichsweikamp
-
Fixed logbook download after switch from CCR to extra (OC) gas if the extra gasFri, 03 Mar 2023 10:41:44 +0100, by heinrichsweikamp
-
Fixed invalid setpoint (0.0) used after switch from CCR to extra (OC) gasTue, 14 Feb 2023 10:21:56 +0100, by heinrichsweikamp
-
Removed interface selection from sensor menu:Sun, 15 Jan 2023 21:51:54 +0100, by Ideenmodellierer
-
Optical sensor as default:Sun, 15 Jan 2023 21:48:34 +0100, by Ideenmodellierer
-
Fix compiler switch:Sun, 15 Jan 2023 21:45:14 +0100, by Ideenmodellierer
-
Improvment sensor Autodetection:Sun, 15 Jan 2023 21:43:33 +0100, by Ideenmodellierer
-
Update sensor menu support for automatic sensor detection:Sat, 14 Jan 2023 20:49:40 +0100, by Ideenmodellierer
-
Added auto detection functionality for sensors connected to the external interface:Sat, 14 Jan 2023 20:46:17 +0100, by Ideenmodellierer
-
Added sensor map to Firmware <=> RTE inferface:Sat, 14 Jan 2023 20:41:36 +0100, by Ideenmodellierer
-
Enabled CO2 support for beta test phase:Sat, 14 Jan 2023 20:37:20 +0100, by Ideenmodellierer
-
Bugfix data synchronization after RTE start:Sat, 14 Jan 2023 20:35:40 +0100, by Ideenmodellierer
-
Update CO2 sensor implementation:Sat, 07 Jan 2023 18:11:52 +0100, by Ideenmodellierer
-
Development feature: external pressure sensorThu, 05 Jan 2023 18:30:06 +0100, by Ideenmodellierer
-
DigO2 added raw data request:Thu, 05 Jan 2023 18:27:04 +0100, by Ideenmodellierer
-
Show saturation in large font (T3) view:Thu, 05 Jan 2023 18:25:47 +0100, by Ideenmodellierer
-
DigO2 added raw data request:Thu, 05 Jan 2023 18:22:21 +0100, by Ideenmodellierer
-
Bugfix set date (year):Tue, 03 Jan 2023 19:47:12 +0100, by Ideenmodellierer
-
Add build for 1.6.1 beta / RTE 2.9 (Support for DiveO2 solid state oxygen sensors)Sun, 27 Nov 2022 15:18:00 +0100, by heinrichsweikamp
-
Updated menu structure to support new sensor information page:Sun, 20 Nov 2022 20:49:41 +0100, by Ideenmodellierer
-
Added new info page for extended sensor data:Sun, 20 Nov 2022 20:46:10 +0100, by Ideenmodellierer
-
Added customizable data area for specific sensor data:Sun, 20 Nov 2022 20:43:04 +0100, by Ideenmodellierer
-
Increased version number and set beta labelSun, 20 Nov 2022 20:42:33 +0100, by Ideenmodellierer
-
Added customizable data area for specific sensor data:Sun, 20 Nov 2022 20:42:08 +0100, by Ideenmodellierer
-
Increased version number and set beta labelSun, 20 Nov 2022 20:37:44 +0100, by Ideenmodellierer
-
Bugfix PSCR menu button label:Sun, 20 Nov 2022 20:36:34 +0100, by Ideenmodellierer
-
Development bugfix number of spare bytes in setting structureTue, 08 Nov 2022 22:16:56 +0100, by Ideenmodellierer
-
Extension scrubber time:Tue, 08 Nov 2022 21:16:17 +0100, by Ideenmodellierer
-
Bugfix compass bearing:Tue, 08 Nov 2022 21:13:14 +0100, by Ideenmodellierer
-
Menu cleanup rebreather specific settings:Thu, 03 Nov 2022 20:44:51 +0100, by Ideenmodellierer
-
Menu cleanup rebreather specific settings:Thu, 03 Nov 2022 20:44:21 +0100, by Ideenmodellierer
-
Bugfix: only reset menu if a new sub menu is created:Thu, 03 Nov 2022 20:37:06 +0100, by Ideenmodellierer
-
Bugfix release frame:Tue, 01 Nov 2022 09:55:45 +0100, by Ideenmodellierer
-
Added protocol functions for UART DiveO2 sensor:Fri, 28 Oct 2022 20:49:21 +0200, by Ideenmodellierer
-
Added selection of digital o2 sensor source to HW menu:Fri, 28 Oct 2022 20:32:24 +0200, by Ideenmodellierer
-
Added digital o2 sensor to settings and data exchange:Fri, 28 Oct 2022 20:29:37 +0200, by Ideenmodellierer
-
Bugfix display of deactivated sensors:Fri, 28 Oct 2022 19:39:20 +0200, by Ideenmodellierer
-
Bugfix motioncontrol frame deactivation:Tue, 18 Oct 2022 21:21:32 +0200, by Ideenmodellierer
-
Cleanup warnings:Tue, 18 Oct 2022 20:56:19 +0200, by Ideenmodellierer
-
Bugfix Empty menu:Sun, 25 Sep 2022 21:13:45 +0200, by Ideenmodellierer
-
Improvment key event detection:Sun, 25 Sep 2022 21:09:18 +0200, by Ideenmodellierer
-
MergeFri, 19 Aug 2022 11:30:24 +0200, by heinrichsweikamp
-
Improvment charge percent visualization: BetatestFri, 05 Aug 2022 16:04:52 +0200, by Ideenmodellierer
-
Added compile switch for Sentinel rebreather option BetatestFri, 05 Aug 2022 15:27:01 +0200, by Ideenmodellierer
-
Added sanity check for temperature and pressure values: BetatestFri, 05 Aug 2022 15:13:29 +0200, by Ideenmodellierer
-
Bugfix automatic switch to o2 sensor custom view: BetatestWed, 03 Aug 2022 18:19:03 +0200, by Ideenmodellierer
-
Ignore automatic setpoint changes during ascend: BetatestThu, 02 Jun 2022 20:24:59 +0200, by Ideenmodellierer
-
Bugfix: Set actual gas after basic dive settings were created: BetatestMon, 16 May 2022 20:50:26 +0200, by Ideenmodellierer
-
Bugfix low ppO2 warning in bailout mode: BetatestMon, 25 Apr 2022 21:15:01 +0200, by Ideenmodellierer
-
Bugfix screen clipping (Flipdisplay mode): BetatestMon, 25 Apr 2022 21:10:10 +0200, by Ideenmodellierer
-
Bugfix: deco planner did not initialize properly BetatestThu, 21 Apr 2022 21:02:50 +0200, by Jan Mulder
-
Bugfix: Missing flip screen support for charge view BetatestWed, 30 Mar 2022 18:07:21 +0200, by Ideenmodellierer
-
Show 98% in case of Oxygen as the calibrating gas BetatestWed, 30 Mar 2022 18:00:21 +0200, by heinrichsweikamp
-
Support of unknown charging counter values: BetatestSat, 12 Mar 2022 22:58:22 +0100, by Ideenmodellierer
-
Reduce display brightness in case the charger is connected: BetatestSat, 12 Mar 2022 22:54:26 +0100, by Ideenmodellierer
-
increase version numbers for upcomming release BetatestSat, 12 Mar 2022 14:57:54 +0100, by heinrichsweikamp
-
Stability improvment bluetooth startup: BetatestTue, 21 Dec 2021 19:36:41 +0100, by Ideenmodellierer
-
Undo Rev. 660Mon, 01 Nov 2021 12:39:34 +0100, by heinrichs weikamp
-
Add option to reset bluetooth nameSun, 08 Aug 2021 09:36:23 +0200, by heinrichsweikamp
-
Update build file for testingWed, 28 Apr 2021 09:47:25 +0200, by heinrichs weikamp
-
Bugfix handling of new menu tab in flipped mode:Tue, 27 Apr 2021 21:29:26 +0200, by Ideenmodellierer
-
Update release dateMon, 26 Apr 2021 15:03:04 +0200, by heinrichs weikamp
-
Added visualization of scrubber time:Sun, 25 Apr 2021 20:47:01 +0200, by Ideenmodellierer
-
Added count down timer for scrubber time:Sun, 25 Apr 2021 20:42:56 +0200, by Ideenmodellierer
-
Introduced new menu tab for addition CCR options:Sun, 25 Apr 2021 20:41:19 +0200, by Ideenmodellierer
-
Bugfix temperature display Logpage2:Sun, 25 Apr 2021 20:36:18 +0200, by Ideenmodellierer
-
Allow setpoint starting at 0.4 ppO2:Mon, 19 Apr 2021 20:34:53 +0200, by Ideenmodellierer
-
Automatik setpoint change:Mon, 19 Apr 2021 20:20:38 +0200, by Ideenmodellierer
-
Automatik setpoint change:Mon, 19 Apr 2021 20:19:32 +0200, by Ideenmodellierer
-
Bugfix consider checkbox in calculation of right aligned and centered position:Mon, 19 Apr 2021 20:16:24 +0200, by Ideenmodellierer
-
Motion detection: Enable focus after focus calibration:Mon, 19 Apr 2021 20:14:20 +0200, by Ideenmodellierer
-
Integrated selection of bailout in the diluent selection page:Tue, 13 Apr 2021 19:25:41 +0200, by Ideenmodellierer
-
Remove battery charge counter from information menu:Tue, 13 Apr 2021 19:21:14 +0200, by Ideenmodellierer
-
Small changes in charger state handling:Tue, 13 Apr 2021 19:18:32 +0200, by Ideenmodellierer
-
Compile with ENABLE_CHARGER_STATUS_V2Tue, 30 Mar 2021 10:34:12 +0200, by heinrichs weikamp
-
Reimplemented charger status generation (deactivated):Wed, 24 Mar 2021 22:06:00 +0100, by Ideenmodellierer
-
Do not show focus indicator in case motion detection is suspended:Wed, 24 Mar 2021 21:28:41 +0100, by Ideenmodellierer
-
Development Bugfix Deco bars not shown after last deco stop passed:Thu, 11 Mar 2021 21:45:22 +0100, by Ideenmodellierer
-
Development bugfix Viewport settings:Thu, 11 Mar 2021 21:43:43 +0100, by Ideenmodellierer
-
add build for testing, advance to FW1.5.7, RTE is unchanged since 1.5.6Thu, 25 Feb 2021 12:20:43 +0100, by heinrichsweikamp
-
Added last measured PPO2 value to sensor selection dialog:Wed, 24 Feb 2021 21:45:35 +0100, by Ideenmodellierer
-
Debounce fallback warning:Wed, 24 Feb 2021 21:04:07 +0100, by Ideenmodellierer
-
Debounce fallback warning:Wed, 24 Feb 2021 21:03:54 +0100, by Ideenmodellierer
-
Debounce fallback warning:Wed, 24 Feb 2021 21:03:22 +0100, by Ideenmodellierer
-
Enable sensor check for Analog PPO2 mode:Wed, 24 Feb 2021 19:18:26 +0100, by Ideenmodellierer
-
Added menu structure to allow ppo2 modification in simulator mode:Tue, 23 Feb 2021 21:58:18 +0100, by Ideenmodellierer
-
Warnings:Tue, 23 Feb 2021 21:55:52 +0100, by Ideenmodellierer
-
Warnings:Tue, 23 Feb 2021 21:55:26 +0100, by Ideenmodellierer
-
Warnings:Tue, 23 Feb 2021 21:54:56 +0100, by Ideenmodellierer
-
Added functionality to add ppo2 mV offset:Tue, 23 Feb 2021 21:53:24 +0100, by Ideenmodellierer
-
Added compile switch for T3_PROFILE menu operation optionFri, 12 Feb 2021 21:46:36 +0100, by Ideenmodellierer
-
Improve in / out of focus transitions:Fri, 12 Feb 2021 21:43:27 +0100, by Ideenmodellierer
-
Added option to select sensitivity of focus detection:Fri, 12 Feb 2021 21:37:50 +0100, by Ideenmodellierer
-
Switch Sector / Scroll detection to vector implementation:Mon, 08 Feb 2021 21:35:46 +0100, by Ideenmodellierer
-
Development bugfix: Marker in standard t3 view drawn in wrong directionSun, 07 Feb 2021 22:05:32 +0100, by Ideenmodellierer
-
Improvment frame Handling:Sun, 07 Feb 2021 22:04:43 +0100, by Ideenmodellierer
-
Adjustments for flipped display view:Wed, 03 Feb 2021 21:45:48 +0100, by Ideenmodellierer
-
Use roll and pitch agles in 0-360 format:Wed, 03 Feb 2021 21:44:22 +0100, by Ideenmodellierer
-
Added minilog functions to allow marker synchronisation:Wed, 27 Jan 2021 22:12:44 +0100, by Ideenmodellierer
-
Added t3 quick menu for marker synchronisation:Wed, 27 Jan 2021 22:10:11 +0100, by Ideenmodellierer
-
Development bugfix: focus state not remembered:Wed, 27 Jan 2021 22:04:45 +0100, by Ideenmodellierer
-
Development bugfix: Low battery warning was interpretated as marker:Wed, 27 Jan 2021 22:03:11 +0100, by Ideenmodellierer
-
Development bugfix: show replay symbol only for the selected dive:Wed, 27 Jan 2021 21:58:46 +0100, by Ideenmodellierer
-
Moved non critical functions from timer interrupt to main loop:Wed, 27 Jan 2021 21:56:48 +0100, by Ideenmodellierer
-
Added "Set Marker" to T3 quick menu:Wed, 20 Jan 2021 20:05:05 +0100, by Ideenmodellierer
-
Added "Set Marker" to T3 quick menu:Fri, 15 Jan 2021 21:33:07 +0100, by Ideenmodellierer
-
Bugfix inverted whitspace:Fri, 15 Jan 2021 21:20:29 +0100, by Ideenmodellierer
-
Suspend MotionDetection events while diver is operationg the OSTC:Thu, 14 Jan 2021 21:25:15 +0100, by Ideenmodellierer
-
Added access to logbook marker data:Thu, 14 Jan 2021 20:38:28 +0100, by Ideenmodellierer
-
Bugfix: CalibViewport were shown even in case the compile switch had not been set:Thu, 14 Jan 2021 19:17:28 +0100, by Ideenmodellierer
-
Update RTE required value for releaseFri, 05 Feb 2021 14:53:50 +0100, by heinrichsweikamp
-
Added tag v1.5.6 release for changeset 06ec1da5e105Fri, 05 Feb 2021 14:50:18 +0100, by heinrichsweikamp
-
change O2_CALIB_FRACTION_O2 to 0.98Thu, 07 Jan 2021 09:53:04 +0100, by heinrichsweikamp
-
Merged menu items of viewport and motion control:Wed, 06 Jan 2021 21:01:00 +0100, by Ideenmodellierer
-
T3 profile view: Added visualization of deco dataWed, 06 Jan 2021 19:41:43 +0100, by Ideenmodellierer
-
Added replay data scaling in case life data is longer than replay blockTue, 05 Jan 2021 20:35:01 +0100, by Ideenmodellierer
-
Bugfix T3 skip deactivated views:Mon, 04 Jan 2021 22:49:07 +0100, by Ideenmodellierer
-
Added compile switch for new T3 View ProfileMon, 04 Jan 2021 22:45:37 +0100, by Ideenmodellierer
-
Bugfix T3 skip deactivated views:Mon, 04 Jan 2021 21:48:31 +0100, by Ideenmodellierer
-
New replay block for T3 profile:Mon, 04 Jan 2021 21:41:51 +0100, by Ideenmodellierer
-
MotionControl-Sector: Map sectors during switch T7 <=> T3:Mon, 04 Jan 2021 21:38:28 +0100, by Ideenmodellierer
-
Added functionality to select a dive to be shown in the T3 profile view:Mon, 04 Jan 2021 21:35:38 +0100, by Ideenmodellierer
-
Bugfix Selection of primary view:Mon, 04 Jan 2021 21:32:39 +0100, by Ideenmodellierer
-
Added compile switch for new T3 View ProfileMon, 04 Jan 2021 21:30:04 +0100, by Ideenmodellierer
-
Added PrintGraph option to skip invalid data entries:Mon, 04 Jan 2021 21:24:24 +0100, by Ideenmodellierer
-
MotionCtrl - Sectorview Map sectors directly to custom views:Sun, 03 Jan 2021 14:43:16 +0100, by Ideenmodellierer
-
Minor: Comment translation into EnglishWed, 06 Jan 2021 22:02:49 +0100, by heinrichsweikamp
-
Align VPM tag in log list to be at same position as GF tag:Tue, 22 Dec 2020 22:23:11 +0100, by Ideenmodellierer
-
Minor: Update the documentation for building the codeThu, 17 Dec 2020 10:58:28 +0100, by heinrichsweikamp
-
Update current build, "RTErequired" value and release dateThu, 17 Dec 2020 09:52:12 +0100, by heinrichsweikamp
-
update ostc4pack sample filesWed, 16 Dec 2020 09:43:11 +0100, by heinrichsweikamp
-
Motion control: Jump back to primary view if focus is lost:Sun, 13 Dec 2020 18:31:40 +0100, by Ideenmodellierer
-
Reduced view angle and number of vusiualized custom views in setor mode:Sun, 13 Dec 2020 18:29:12 +0100, by Ideenmodellierer
-
Added option for 100% o2 calibration:Sat, 12 Dec 2020 21:05:11 +0100, by Ideenmodellierer
-
Solved minor warningsSat, 12 Dec 2020 20:54:31 +0100, by Ideenmodellierer
-
Show Fallback if no valid sensor value is available:Sat, 12 Dec 2020 20:52:58 +0100, by Ideenmodellierer
-
Added ex Interface measurement restart in case of i2c disturbance:Sat, 12 Dec 2020 19:18:57 +0100, by Ideenmodellierer
-
Bugfix bad resolution of compass LSM303AGR:Sat, 12 Dec 2020 19:16:37 +0100, by Ideenmodellierer
-
Minor: Functional inert cleanup of some unused variablesThu, 03 Dec 2020 13:17:32 +0100, by heinrichsweikamp
-
Rework pitch detection:Sun, 29 Nov 2020 23:02:11 +0100, by Ideenmodellierer
-
Handle o2 voltage values < 0.5mV as invalid:Sun, 29 Nov 2020 22:58:11 +0100, by Ideenmodellierer
-
Return to o2 values:Sun, 29 Nov 2020 22:55:31 +0100, by Ideenmodellierer
-
Change style of viewport calibration menu:Sun, 29 Nov 2020 22:53:33 +0100, by Ideenmodellierer
-
Improved focus detection:Wed, 25 Nov 2020 20:26:01 +0100, by Ideenmodellierer
-
Update String "Blickwinkel":Wed, 25 Nov 2020 20:19:50 +0100, by Ideenmodellierer
-
Added debug view to viewport calibration:Wed, 25 Nov 2020 20:18:22 +0100, by Ideenmodellierer
-
Reactivate compass parameter stored in NVM:Wed, 25 Nov 2020 20:16:20 +0100, by Ideenmodellierer
-
Try to reduce legth of log entry string:Mon, 30 Nov 2020 20:55:23 +0100, by Ideenmodellierer
-
Added new section "lower.font":Mon, 30 Nov 2020 20:52:49 +0100, by Ideenmodellierer
-
Minor: Update the documentation for building the codeSun, 29 Nov 2020 11:41:03 +0100, by heinrichsweikamp
-
-Add 12HR Time SupportTue, 24 Nov 2020 13:22:23 -0600, by izzni
-
add current buildSat, 21 Nov 2020 17:41:59 +0100, by heinrichsweikamp
-
Bugfix center / right alignment if dualfont is used:Sun, 15 Nov 2020 20:12:19 +0100, by Ideenmodellierer
-
Bugfix One or more deactivated sensors hide sensor display:Sun, 15 Nov 2020 20:09:31 +0100, by Ideenmodellierer
-
Refine o2 sensor diagnostic functions:Sun, 15 Nov 2020 20:01:56 +0100, by Ideenmodellierer
-
Added ADC sensor interface to O2 sensore menu structure:Sun, 15 Nov 2020 19:58:14 +0100, by Ideenmodellierer
-
Solved minor warningsSun, 15 Nov 2020 19:54:36 +0100, by Ideenmodellierer
-
Added O2 sensor source and calibration parameters to setting structureSun, 15 Nov 2020 19:53:09 +0100, by Ideenmodellierer
-
Check if HW evaluation was performed:Sun, 15 Nov 2020 19:52:03 +0100, by Ideenmodellierer
-
Changed operation mode of RecoverSampleIndex:Thu, 12 Nov 2020 20:06:04 +0100, by Ideenmodellierer
-
Stabilityfix: Do not trust lastDiveLogID == 0 at startup:Thu, 12 Nov 2020 20:03:00 +0100, by Ideenmodellierer
-
Switch source of o2 sensor data depending on availability of external ADC:Thu, 12 Nov 2020 19:54:58 +0100, by Ideenmodellierer
-
Added HW_Info to Discovery <=> RTE data exchange:Thu, 12 Nov 2020 19:48:28 +0100, by Ideenmodellierer
-
Added external ADC interface functionality (MCP3424):Thu, 12 Nov 2020 19:46:03 +0100, by Ideenmodellierer
-
Added color indicator for focus state:Sun, 08 Nov 2020 18:49:54 +0100, by Ideenmodellierer
-
Added menu structure to acces viewport calibration:Sun, 08 Nov 2020 18:46:46 +0100, by Ideenmodellierer
-
Added viewport functionality:Sun, 08 Nov 2020 18:43:19 +0100, by Ideenmodellierer
-
Make sure motion detection settings are set to default values:Sun, 08 Nov 2020 18:38:53 +0100, by Ideenmodellierer
-
Only execute motion detection functions if features is enabled:Sun, 08 Nov 2020 18:36:02 +0100, by Ideenmodellierer
-
Update roll and pitch value in simulation mode:Sun, 08 Nov 2020 16:38:43 +0100, by Ideenmodellierer
-
Added viewport calibration to dive menu:Mon, 02 Nov 2020 21:17:45 +0100, by Ideenmodellierer
-
Added new settings for Viewport:Mon, 02 Nov 2020 21:15:42 +0100, by Ideenmodellierer
-
Add I2C address for external bulkhead ADC (Hardware gen 3 only) to i2c.hTue, 03 Nov 2020 12:47:51 +0100, by heinrichsweikamp