ostc4: revision graph

graph

less more | rev 790: (0) -300 -100 -50 -30 +30 +50 +100 tip

Fix bug introduced in 04b98a2, causing the deco planner to not show deco stops.
20 months ago, by heinrichsweikamp
When using automatic setpoint switching, allow the user to set an arbitrary ppO2 as a custom setpoint during the dive.
20 months ago, by heinrichsweikamp
Define explicit setpoints for low / high / deco. Add an option to delay the switch to SPlow until all decompression has been cleared. (mikeller)
21 months ago, by heinrichsweikamp
Dev Bugfx Empty buffer indication and stability improvments:
22 months ago, by Ideenmodellierer
Cleanup sensor data interface:
22 months ago, by Ideenmodellierer
Change support from Pyroscience -> DiveO2 sensors
22 months ago, by heinrichsweikamp
Bugfixloop UART multiplexer integration:
22 months ago, by Ideenmodellierer
Update digital O2 sensor information:
22 months ago, by Ideenmodellierer
Sensor status support for multiplexed DiveO2 sensors:
22 months ago, by Ideenmodellierer
Update real multiplexer implementation:
22 months ago, by Ideenmodellierer
Discovery<=>SmallCPU inferface update:
22 months ago, by Ideenmodellierer
Added UART multiplexer support for DiveO2:
22 months ago, by Ideenmodellierer
Zusammenf?hren
22 months ago, by heinrichsweikamp
This is only showing if one of the compass views is visible. It should make it possible to verify that a correct heading is set as the user can see the compass readout when pushing the button. (mikeller)
22 months ago, by heinrichsweikamp
Add support for a configurable compass declination in a range of -99 to 99 degrees.
22 months ago, by heinrichsweikamp
Add a shortcuts to change the setpoint to the loop to the 'normal' display when diving. It is only shown when diving in CCR mode and on the loop.
23 months ago, by heinrichsweikamp
more menu items for the compass menu: Delete bearing, and reset to land based bearing. I have also re-enabled the real time bearing display in the menu - makes it easier to set the correct bearing. (mikeller)
23 months ago, by heinrichsweikamp
Menu shortcut for bailout / return to circuit when diving in CCR mode (mikeller)
23 months ago, by heinrichsweikamp
Fix character truncation when screen is flipped. This was causing the dive computer to lock up when in English Units with the screen flipped when the first decompression stop is shown using FONT_105.
23 months ago, by izzni
Revised automatic setpoint change. The proposed approach is essentially the approach used by most controllers of eCCR ('upshift' on descent, 'downshift' on ascent), so that the OSTC4 when used as a backup computer for eCCR will make the changes at the same time as the eCCR itself.
23 months ago, by heinrichsweikamp
CCR overview in surface mode. Makes it easy to quickly check that all settings (mode, setpoints, diluent, scrubber timer) are correct when preparing to dive (also makes the OC gas list available in surface mode for the same reason).
23 months ago, by heinrichsweikamp
Deactivation of the 'fallback' option when the CCR mode is set to 'Fixed' - this makes it a little clearer that the option has no influence in this mode.
23 months ago, by heinrichsweikamp
1.6.2 release
23 months ago, by heinrichsweikamp
Update build for testing
24 months ago, by heinrichsweikamp
change button default responsiveness to 100
24 months ago, by heinrichsweikamp
After a firmware update, use the factory settings for button sensitivity if these exist, the default settings otherwise.
24 months ago, by heinrichsweikamp
Update build for testing
2023-03-27, by heinrichsweikamp
increase HAL_Delay to 10ms for cold-start-button reset
2023-03-26, by heinrichsweikamp
Preparing a 1.6.2 release candidate
2023-03-26, by heinrichsweikamp
Fix/handle negative scrubber timer values
2023-03-21, by heinrichsweikamp

less more | rev 790: (0) -300 -100 -50 -30 +30 +50 +100 tip