| Tue, 01 Oct 2019 19:13:41 +0200 |
ideenmodellierer |
Removed averaging of pressure and temperatur values
FlightMode_Improvment
|
| Sun, 06 Oct 2019 14:07:51 +0200 |
heinrichsweikamp |
change max. allowed surface pressure to 1030hPa (As in the small OSTC)
|
| Mon, 19 Aug 2019 11:42:31 +0000 |
heinrichsweikamp |
Merged in Ideenmodellierer/ostc4/PressureMeasure_Improvment (pull request #31)
|
| Sat, 17 Aug 2019 19:03:47 +0200 |
ideenmodellierer |
Apply averaging to pressure measurement: In pre versions calculated pressure value jittered +/-10hPa. Since we measure the pressure several time a second but only use one value a second, calc average including not used values
PressureMeasure_Improvment
|
| Sat, 17 Aug 2019 18:57:15 +0200 |
ideenmodellierer |
Added function to avoid divemode activation during Landing:
PressureMeasure_Improvment
|
| Sat, 17 Aug 2019 18:47:08 +0200 |
ideenmodellierer |
Set Max value for pressure offset to 50mBar (20mBar before)
PressureMeasure_Improvment
|
| Sat, 17 Aug 2019 18:44:43 +0200 |
ideenmodellierer |
Show actual instead of surface (30minute old) pressure if the actual differs significant (e.g. in plane or during pressure testing)
PressureMeasure_Improvment
|
| Tue, 13 Aug 2019 21:46:26 +0200 |
ideenmodellierer |
Use average calculation for pressure: precondition was that pressure values jittered +- 10 HPa from one capture (once a second) to the other. Basically pressure is measured several times a second => using these values in an additional history calculation reduces the jitter down to +-1 per second
PressureMeasure_Improvment
|
| Sun, 04 Aug 2019 11:01:06 +0200 |
heinrichsweikamp |
building a 1.5
v1.5.0 release
|
| Sat, 20 Jul 2019 10:44:01 +0200 |
heinrichsweikamp |
add update files for testing purposes
|
| Thu, 18 Jul 2019 14:26:56 +0000 |
heinrichsweikamp |
Merged in Ideenmodellierer/ostc4/I2C_Improvment (pull request #30)
|
| Wed, 17 Jul 2019 22:43:51 +0200 |
ideenmodellierer |
Added plausibility check for pressure values
I2C_Improvment
|
| Wed, 17 Jul 2019 22:43:16 +0200 |
ideenmodellierer |
Added check of configuration.
I2C_Improvment
|
| Wed, 17 Jul 2019 22:42:55 +0200 |
ideenmodellierer |
Improved startup robustness
I2C_Improvment
|
| Wed, 17 Jul 2019 22:42:15 +0200 |
ideenmodellierer |
Set I2C speed to 88kHz, use digital filter only and reworked idle clock recovery
I2C_Improvment
|
| Wed, 17 Jul 2019 22:41:31 +0200 |
ideenmodellierer |
Deactivated internal pullups and I2C interrupt callback
I2C_Improvment
|
| Mon, 01 Jul 2019 14:18:39 +0000 |
heinrichsweikamp |
Merged in janlmulder/ostc4/fix-batt-1 (pull request #29)
|
| Thu, 20 Jun 2019 14:24:57 +0200 |
Jan Mulder |
bugfix: implement battery at end in dive header
fix-batt-1
|
| Sun, 30 Jun 2019 22:12:15 +0200 |
heinrichsweikamp |
increase RTE to 1.9 and Firmware to 1.4.9 beta
|
| Sun, 30 Jun 2019 19:52:46 +0000 |
heinrichsweikamp |
Merged in Ideenmodellierer/ostc4/O2_SensorSync (pull request #28)
|
| Sun, 30 Jun 2019 21:25:58 +0200 |
ideenmodellierer |
Added start of frame detection for HUD data
O2_SensorSync
|
| Sun, 30 Jun 2019 21:18:05 +0200 |
ideenmodellierer |
Moved indication variable for received HUD data to tCCR file.
O2_SensorSync
|
| Wed, 19 Jun 2019 13:12:25 +0000 |
heinrichsweikamp |
Merged in janlmulder/ostc4/fix-version (pull request #27)
|
| Wed, 19 Jun 2019 14:31:50 +0200 |
Jan Mulder |
bugfix: correct packed main version number in dive header
fix-version
|
| Wed, 19 Jun 2019 13:12:01 +0000 |
heinrichsweikamp |
Merged in Ideenmodellierer/ostc4/Bugfix_Flip_FirmwareUpdate (pull request #26)
|
| Mon, 17 Jun 2019 21:47:54 +0200 |
ideenmodellierer |
Resolved warning
Bugfix_Flip_FirmwareUpdate
|
| Mon, 17 Jun 2019 21:47:33 +0200 |
ideenmodellierer |
Bugfix text display in update mode (flipped display) and reduction of timeout in case of a failed firmware update
Bugfix_Flip_FirmwareUpdate
|
| Mon, 17 Jun 2019 21:47:19 +0200 |
ideenmodellierer |
Bugfix Overview, O2 values and mV in flip display mode
Bugfix_Flip_FirmwareUpdate
|
| Mon, 17 Jun 2019 21:46:56 +0200 |
ideenmodellierer |
Reinitialize logos after flip of display
Bugfix_Flip_FirmwareUpdate
|
| Sat, 01 Jun 2019 10:12:15 +0200 |
heinrichsweikamp |
Minor: Remove unused compass header file. The LSM303DLHC is not used in any hardware sold.
|
| Fri, 31 May 2019 06:22:50 +0000 |
heinrichsweikamp |
Merged in janlmulder/ostc4/cleanup-4 (pull request #25)
|
| Wed, 29 May 2019 14:02:27 +0200 |
Jan Mulder |
bugfix: make stopwatch and divetime run in sync
cleanup-4
|
| Sun, 26 May 2019 10:09:22 +0200 |
Jan Mulder |
Make dive mode detection more advanced
cleanup-4
|
| Fri, 24 May 2019 09:29:29 +0200 |
Jan Mulder |
cleanup: factor out SHelper typedef (and more)
cleanup-4
|
| Fri, 24 May 2019 09:02:46 +0200 |
Jan Mulder |
cleanup: introduce function setAvgDepth
cleanup-4
|
| Wed, 22 May 2019 22:22:15 +0200 |
Jan Mulder |
cleanup: factor out unused stopwatch code
cleanup-4
|
| Wed, 22 May 2019 14:39:04 +0200 |
Jan Mulder |
bugfix, cleanup: do not clip depth to 0
cleanup-4
|
| Tue, 21 May 2019 11:11:05 +0200 |
Jan Mulder |
bugfix, consistency: show deco/NDL really after 1 minute divetime
cleanup-4
|
| Mon, 20 May 2019 13:06:02 +0200 |
Jan Mulder |
bugfix, simulator: fix the 1 sec difference between stopwatch and divetime
cleanup-4
|
| Mon, 20 May 2019 12:57:31 +0200 |
Jan Mulder |
bugfix, cleanup: simplify stopwatch logic and fix fallout
cleanup-4
|
| Mon, 20 May 2019 10:13:44 +0200 |
Jan Mulder |
bugfix, cleanup: keep both is_ambient_pressure_close_to_surface in sync
cleanup-4
|
| Mon, 20 May 2019 10:05:27 +0200 |
Jan Mulder |
cleanup, RTE: factor out scheduleCheck_pressure_reached_dive_mode_level
cleanup-4
|
| Fri, 17 May 2019 21:19:04 +0200 |
Jan Mulder |
cleanup: remove commented/unused code, make static
cleanup-4
|
| Fri, 17 May 2019 06:38:56 +0000 |
heinrichsweikamp |
Merged in janlmulder/ostc4/cleanup-3 (pull request #24)
|
| Thu, 16 May 2019 14:02:46 +0200 |
Jan Mulder |
Bugfix: fix drawing of CCR bailout profile
cleanup-3
|
| Thu, 16 May 2019 08:56:15 +0200 |
Jan Mulder |
cleanup: remove unused code, make static, remove commented code
cleanup-3
|
| Thu, 16 May 2019 08:54:33 +0200 |
Jan Mulder |
Possible bugfix: do not use bitwise and (&)
cleanup-3
|
| Mon, 13 May 2019 13:37:34 +0000 |
heinrichsweikamp |
Merged in janlmulder/ostc4/div-fixes-6 (pull request #23)
|
| Sun, 12 May 2019 09:45:32 +0200 |
Jan Mulder |
Added tag v1.4.8 release for changeset ba9d99a2e310
div-fixes-6
|
| Thu, 02 May 2019 10:05:28 +0200 |
Jan Mulder |
bugfix, consistency: show deco, NDL after 1 minute
div-fixes-6
|
| Thu, 02 May 2019 09:24:54 +0200 |
Jan Mulder |
translate: nullzeit -> ndl
div-fixes-6
|
| Thu, 02 May 2019 09:16:07 +0200 |
Jan Mulder |
Deco Models: limit NDL to 240 minutes
div-fixes-6
|
| Thu, 02 May 2019 08:43:07 +0200 |
Jan Mulder |
VPM, cleanup: 1st round
div-fixes-6
|
| Mon, 29 Apr 2019 19:45:25 +0200 |
Jan Mulder |
cleanup: remove unused code
div-fixes-6
|
| Mon, 29 Apr 2019 19:43:05 +0200 |
Jan Mulder |
cleanup: no useless checks for simulator state
div-fixes-6
|
| Mon, 06 May 2019 15:45:19 +0200 |
heinrichsweikamp |
Update the release file for testing. Rev 286 did not include the 1.4.8 (non-beta) firmware.
v1.4.8 release
|
| Mon, 06 May 2019 09:00:58 +0200 |
heinrichsweikamp |
Minor: Some Texts fixed, allign RTErequired* values with RTE firmware
|
| Sun, 05 May 2019 11:06:02 +0200 |
heinrichsweikamp |
add update files for testing purposes
|
| Thu, 02 May 2019 11:12:25 +0000 |
heinrichsweikamp |
Merged in janlmulder/ostc4/ndl-in-logbook (pull request #22)
|
| Thu, 02 May 2019 13:08:17 +0200 |
Jan Mulder |
Bugfix: write NDL in logbook correctly
ndl-in-logbook
|
