| 22 months ago |
Ideenmodellierer |
Update digital O2 sensor information:
|
| 22 months ago |
Ideenmodellierer |
Sensor status support for multiplexed DiveO2 sensors:
|
| 22 months ago |
Ideenmodellierer |
Update real multiplexer implementation:
|
| 22 months ago |
Ideenmodellierer |
Discovery<=>SmallCPU inferface update:
|
| 22 months ago |
Ideenmodellierer |
Added UART multiplexer support for DiveO2:
|
| 22 months ago |
heinrichsweikamp |
Zusammenf?hren
|
| 22 months ago |
heinrichsweikamp |
This is only showing if one of the compass views is visible. It should make it possible to verify that a correct heading is set as the user can see the compass readout when pushing the button. (mikeller)
|
| 22 months ago |
heinrichsweikamp |
Add support for a configurable compass declination in a range of -99 to 99 degrees.
|
| 23 months ago |
heinrichsweikamp |
Add a shortcuts to change the setpoint to the loop to the 'normal' display when diving. It is only shown when diving in CCR mode and on the loop.
|
| 23 months ago |
heinrichsweikamp |
more menu items for the compass menu: Delete bearing, and reset to land based bearing. I have also re-enabled the real time bearing display in the menu - makes it easier to set the correct bearing. (mikeller)
|
| 23 months ago |
heinrichsweikamp |
Menu shortcut for bailout / return to circuit when diving in CCR mode (mikeller)
|
| 23 months ago |
izzni |
Fix character truncation when screen is flipped. This was causing the dive computer to lock up when in English Units with the screen flipped when the first decompression stop is shown using FONT_105.
|
| 23 months ago |
heinrichsweikamp |
Revised automatic setpoint change. The proposed approach is essentially the approach used by most controllers of eCCR ('upshift' on descent, 'downshift' on ascent), so that the OSTC4 when used as a backup computer for eCCR will make the changes at the same time as the eCCR itself.
|
| 23 months ago |
heinrichsweikamp |
CCR overview in surface mode. Makes it easy to quickly check that all settings (mode, setpoints, diluent, scrubber timer) are correct when preparing to dive (also makes the OC gas list available in surface mode for the same reason).
|
| 23 months ago |
heinrichsweikamp |
Deactivation of the 'fallback' option when the CCR mode is set to 'Fixed' - this makes it a little clearer that the option has no influence in this mode.
|
| 23 months ago |
heinrichsweikamp |
1.6.2 release
|
| 24 months ago |
heinrichsweikamp |
Update build for testing
|
| 24 months ago |
heinrichsweikamp |
change button default responsiveness to 100
|
| 24 months ago |
heinrichsweikamp |
After a firmware update, use the factory settings for button sensitivity if these exist, the default settings otherwise.
|
| 2023-03-27 |
heinrichsweikamp |
Update build for testing
|
| 2023-03-26 |
heinrichsweikamp |
increase HAL_Delay to 10ms for cold-start-button reset
|
| 2023-03-26 |
heinrichsweikamp |
Preparing a 1.6.2 release candidate
|
| 2023-03-21 |
heinrichsweikamp |
Fix/handle negative scrubber timer values
|
| 2023-03-21 |
heinrichsweikamp |
Quit simualted dives after the dive time set in the SIM tab.
|
| 2023-03-17 |
heinrichsweikamp |
Some compass improvements from mikeller
|
| 2023-03-15 |
heinrichsweikamp |
- Colours for scrubber display when time remaining falls below a threshold value
|
| 2023-03-07 |
Ideenmodellierer |
Dev Bugfix: ignore analog out of bounds limits for DiveO2 sensor:
|
| 2023-03-07 |
Ideenmodellierer |
Added visualization of CO2 during dive:
|
| 2023-03-07 |
Ideenmodellierer |
Cleanup display of multiple warnings in T3 (Big font) view:
|
| 2023-03-07 |
Ideenmodellierer |
Only show autodetection in sensor menu if external interface is present:
|
