| Fri, 21 Apr 2023 09:48:23 +0200 |
heinrichsweikamp |
Revised automatic setpoint change. The proposed approach is essentially the approach used by most controllers of eCCR ('upshift' on descent, 'downshift' on ascent), so that the OSTC4 when used as a backup computer for eCCR will make the changes at the same time as the eCCR itself.
|
| Fri, 21 Apr 2023 09:47:44 +0200 |
heinrichsweikamp |
CCR overview in surface mode. Makes it easy to quickly check that all settings (mode, setpoints, diluent, scrubber timer) are correct when preparing to dive (also makes the OC gas list available in surface mode for the same reason).
|
| Fri, 21 Apr 2023 09:47:06 +0200 |
heinrichsweikamp |
Deactivation of the 'fallback' option when the CCR mode is set to 'Fixed' - this makes it a little clearer that the option has no influence in this mode.
|
| Thu, 13 Apr 2023 09:35:43 +0200 |
heinrichsweikamp |
1.6.2 release
|
| Wed, 12 Apr 2023 09:56:00 +0200 |
heinrichsweikamp |
Update build for testing
|
| Wed, 12 Apr 2023 09:30:15 +0200 |
heinrichsweikamp |
change button default responsiveness to 100
|
| Wed, 12 Apr 2023 09:24:44 +0200 |
heinrichsweikamp |
After a firmware update, use the factory settings for button sensitivity if these exist, the default settings otherwise.
|
| Mon, 27 Mar 2023 10:04:53 +0200 |
heinrichsweikamp |
Update build for testing
|
| Sun, 26 Mar 2023 18:34:30 +0200 |
heinrichsweikamp |
increase HAL_Delay to 10ms for cold-start-button reset
|
| Sun, 26 Mar 2023 11:27:29 +0200 |
heinrichsweikamp |
Preparing a 1.6.2 release candidate
|
| Tue, 21 Mar 2023 12:57:37 +0100 |
heinrichsweikamp |
Fix/handle negative scrubber timer values
|
| Tue, 21 Mar 2023 12:56:54 +0100 |
heinrichsweikamp |
Quit simualted dives after the dive time set in the SIM tab.
|
| Fri, 17 Mar 2023 09:35:25 +0100 |
heinrichsweikamp |
Some compass improvements from mikeller
|
| Wed, 15 Mar 2023 09:18:07 +0100 |
heinrichsweikamp |
- Colours for scrubber display when time remaining falls below a threshold value
|
| Tue, 07 Mar 2023 22:14:20 +0100 |
Ideenmodellierer |
Dev Bugfix: ignore analog out of bounds limits for DiveO2 sensor:
|
| Tue, 07 Mar 2023 20:02:05 +0100 |
Ideenmodellierer |
Added visualization of CO2 during dive:
|
| Tue, 07 Mar 2023 19:59:02 +0100 |
Ideenmodellierer |
Cleanup display of multiple warnings in T3 (Big font) view:
|
| Tue, 07 Mar 2023 19:55:13 +0100 |
Ideenmodellierer |
Only show autodetection in sensor menu if external interface is present:
|
| Tue, 07 Mar 2023 19:52:18 +0100 |
Ideenmodellierer |
Updated outdated comment
|
| Tue, 07 Mar 2023 19:51:30 +0100 |
Ideenmodellierer |
Dev Bugfix: Alignment problem in lifedata structure:
|
| Mon, 13 Mar 2023 22:23:00 +0100 |
Ideenmodellierer |
resolv merge
|
| Sun, 05 Mar 2023 22:17:32 +0100 |
Ideenmodellierer |
Avoid blinking in customer view selection page:
|
| Mon, 13 Mar 2023 22:18:28 +0100 |
Ideenmodellierer |
Added enum for Co2 display
|
| Sun, 05 Mar 2023 22:14:53 +0100 |
Ideenmodellierer |
Added display of co2 ppm values:
|
| Sun, 05 Mar 2023 22:06:47 +0100 |
Ideenmodellierer |
Added pressure compensation to CO2 detection:
|
| Tue, 21 Feb 2023 21:19:31 +0100 |
Ideenmodellierer |
Code cleanup sensors under development:
|
| Sun, 19 Feb 2023 21:52:02 +0100 |
Ideenmodellierer |
Update Sentinel protocol:
|
| Sun, 19 Feb 2023 21:51:19 +0100 |
Ideenmodellierer |
Added DiveO2 fatal error detection:
|
| Sun, 19 Feb 2023 21:48:47 +0100 |
Ideenmodellierer |
Enable start dive in Big font display:
|
| Sun, 19 Feb 2023 21:43:24 +0100 |
Ideenmodellierer |
Update Sentinel protocol:
|
