ostc4: revision graph

graph

less more | rev 482: (0) -480 tip

Merged in Ideenmodellierer/ostc4/Improve_Button_Sleep (pull request #45)
Tue, 19 May 2020 07:27:18 +0000, by heinrichsweikamp
Bugfix calculation of string center position: Improve_Button_Sleep
Mon, 18 May 2020 21:51:08 +0200, by ideenmodellierer
Code cleanup pressure plausibility check: Improve_Button_Sleep
Wed, 13 May 2020 21:56:35 +0200, by ideenmodellierer
Bugfix unintended else condition: Improve_Button_Sleep
Wed, 13 May 2020 21:27:30 +0200, by ideenmodellierer
Development option only: Show Pressure update for a short time in the custom field (as warning) Improve_Button_Sleep
Tue, 12 May 2020 23:03:50 +0200, by ideenmodellierer
Only switch between "no fly" and "desaturation" in case there is desaturation time left: Improve_Button_Sleep
Tue, 12 May 2020 23:03:29 +0200, by ideenmodellierer
Balance value of button responsitivness were not considered during firmware startup: Improve_Button_Sleep
Tue, 12 May 2020 22:54:19 +0200, by ideenmodellierer
Changed default values: Improve_Button_Sleep
Tue, 12 May 2020 22:52:05 +0200, by ideenmodellierer
Added error detection for reading of ADC values in sleep mode: Improve_Button_Sleep
Tue, 12 May 2020 22:42:52 +0200, by ideenmodellierer
Do not signal power on reset in case of a "warm" reset: Improve_Button_Sleep
Tue, 12 May 2020 22:39:18 +0200, by ideenmodellierer
Merged in janlmulder/ostc4/fix-bat-2 (pull request #44)
Tue, 28 Apr 2020 15:37:47 +0000, by heinrichsweikamp
bugfix: implement battery charge percentage in dive header fix-bat-2
Wed, 22 Apr 2020 13:08:57 +0200, by Jan Mulder
Merged in Ideenmodellierer/ostc4/Improve_Logtansfer (pull request #42)
Wed, 15 Apr 2020 07:01:11 +0000, by heinrichsweikamp
Removed no longer needed reset profile function: Improve_Logtansfer
Tue, 14 Apr 2020 19:45:34 +0200, by ideenmodellierer
Moved and deactivated analyse sample buffer switch: Improve_Logtansfer
Tue, 14 Apr 2020 19:44:19 +0200, by ideenmodellierer
Cmd Get profile: transmit dummy profile if necessary Improve_Logtansfer
Tue, 14 Apr 2020 19:29:23 +0200, by ideenmodellierer
Removed invalidate header function because it is no lonnger needed Improve_Logtansfer
Tue, 14 Apr 2020 19:27:04 +0200, by ideenmodellierer
Compare profile length from header and sample data to identify valid profiles Improve_Logtansfer
Tue, 14 Apr 2020 19:22:56 +0200, by ideenmodellierer
Added compile switch to handle additional data during raw header request: Improve_Logtansfer
Mon, 13 Apr 2020 16:00:54 +0200, by ideenmodellierer
Added function to transfer sample buffer: Improve_Logtansfer
Sun, 12 Apr 2020 21:02:34 +0200, by ideenmodellierer
Power-down Bluetooth on COMM exit
Wed, 08 Apr 2020 16:34:54 +0200, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/minor_improvments (pull request #41)
Mon, 30 Mar 2020 13:16:11 +0000, by heinrichsweikamp
merged default into minor_improvments minor_improvments
Sun, 29 Mar 2020 21:55:00 +0200, by Ideenmodellierer
Activated reset of sample information within header data at time of sector erasing: minor_improvments
Sun, 29 Mar 2020 21:39:57 +0200, by ideenmodellierer
Added ppO2 to dummy profile data: minor_improvments
Sat, 28 Mar 2020 21:41:47 +0100, by ideenmodellierer
Eliminated some minor warnings minor_improvments
Tue, 24 Mar 2020 22:32:48 +0100, by ideenmodellierer
Transfer a dummy profile in case of missing sample information: minor_improvments
Tue, 24 Mar 2020 22:14:16 +0100, by ideenmodellierer
Reactivated samples for bottle pressure information: minor_improvments
Tue, 24 Mar 2020 22:12:08 +0100, by ideenmodellierer
Reactivated samples for bottle pressure information: minor_improvments
Tue, 24 Mar 2020 22:08:29 +0100, by ideenmodellierer
Added compile variant enabling the reset of profile sample information: minor_improvments
Tue, 24 Mar 2020 21:59:38 +0100, by ideenmodellierer
Added compile variant enabling the reset of profile sample information: minor_improvments
Tue, 24 Mar 2020 21:59:11 +0100, by ideenmodellierer
Allocate received bar value to active gas (was static allocated to gas[1]) minor_improvments
Tue, 24 Mar 2020 21:49:52 +0100, by ideenmodellierer
Added new compile switches for variants: minor_improvments
Tue, 24 Mar 2020 21:48:27 +0100, by ideenmodellierer
Added initialization of bottle sensor data age counter minor_improvments
Mon, 23 Mar 2020 21:14:54 +0100, by ideenmodellierer
Added compile switch to show voltage parallel to charge status percantage minor_improvments
Mon, 23 Mar 2020 21:13:52 +0100, by ideenmodellierer
Added compile switch var firmware variant which does trust the memory log => does not check the log consistency at startu (used for test purpose) minor_improvments
Mon, 23 Mar 2020 21:10:02 +0100, by ideenmodellierer
Introduced configuration header for variant managment: minor_improvments
Thu, 05 Mar 2020 22:31:50 +0100, by ideenmodellierer
Removed duplicated definition: minor_improvments
Thu, 05 Mar 2020 22:27:55 +0100, by ideenmodellierer
Introduced enum for lower left corner view selection: minor_improvments
Sat, 29 Feb 2020 22:27:29 +0100, by ideenmodellierer
Introduced enum for lower left corner view selection: minor_improvments
Sat, 29 Feb 2020 22:27:04 +0100, by ideenmodellierer
Introduced enum for lower left corner view selection: minor_improvments
Sat, 29 Feb 2020 22:25:20 +0100, by ideenmodellierer
fix potential issue with >255 dives in the logbook
Sun, 01 Mar 2020 10:06:45 +0100, by heinrichsweikamp
Added tag v1.5.3 release for changeset 5b4c78c36b04
Thu, 27 Feb 2020 09:13:25 +0100, by heinrichsweikamp
1.5.3 release v1.5.3 release
Thu, 27 Feb 2020 09:13:08 +0100, by heinrichsweikamp
update the 1.5.3 for tests
Mon, 24 Feb 2020 15:17:54 +0100, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/Improve_BatteryGasGauge (pull request #40)
Mon, 24 Feb 2020 07:58:37 +0000, by heinrichsweikamp
Moved power on detection to RTE: Improve_BatteryGasGauge
Sun, 23 Feb 2020 21:18:49 +0100, by ideenmodellierer
Bugfix display battery voltage in maintainance menu: Improve_BatteryGasGauge
Sun, 23 Feb 2020 21:17:17 +0100, by ideenmodellierer
Reduced timeout for common UART communication: Improve_BatteryGasGauge
Sun, 23 Feb 2020 21:13:28 +0100, by ideenmodellierer
Detect startup after power off: Improve_BatteryGasGauge
Sun, 23 Feb 2020 21:09:56 +0100, by ideenmodellierer
show battery percent and voltage and surfacemode. That gives additional
Tue, 18 Feb 2020 12:41:45 +0100, by heinrichsweikamp
make a 1.5.3 for tests
Tue, 18 Feb 2020 09:58:52 +0100, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/ImprovmentNVM_2 (pull request #39)
Tue, 18 Feb 2020 07:20:29 +0000, by heinrichsweikamp
Marked possible code improvment for future activities: ImprovmentNVM_2
Mon, 17 Feb 2020 19:43:09 +0100, by ideenmodellierer
Activated ringbuffer for settings: ImprovmentNVM_2
Mon, 17 Feb 2020 19:04:10 +0100, by ideenmodellierer
Activated ringbuffer for settings: ImprovmentNVM_2
Sun, 16 Feb 2020 22:04:52 +0100, by ideenmodellierer
Added function to analyse the sampel ringbuffer: ImprovmentNVM_2
Sat, 15 Feb 2020 20:50:58 +0100, by ideenmodellierer
Added function to analyse the sampel ringbuffer: ImprovmentNVM_2
Sat, 15 Feb 2020 20:50:20 +0100, by ideenmodellierer
Added (optional) menu item to analyse log sample buffer: ImprovmentNVM_2
Sat, 15 Feb 2020 20:45:19 +0100, by ideenmodellierer
ext_Flash_write_sample erase sector optimization: ImprovmentNVM_2
Mon, 10 Feb 2020 19:40:33 +0100, by ideenmodellierer
Moved Timeout handling out of 100ms callback: ImprovmentNVM_2
Mon, 10 Feb 2020 19:29:12 +0100, by ideenmodellierer
Enable sequentionel writing of device data: ImprovmentNVM_2
Mon, 10 Feb 2020 19:25:09 +0100, by ideenmodellierer
Optimize ef_write_block function: ImprovmentNVM_2
Mon, 10 Feb 2020 19:15:27 +0100, by ideenmodellierer
Merged in janlmulder/ostc4/maintain-2 (pull request #38)
Mon, 10 Feb 2020 08:23:15 +0000, by heinrichsweikamp
Added tag v1.5.2.beta release for changeset 54a480c43e97 maintain-2
Fri, 07 Feb 2020 16:38:11 +0100, by Jan Mulder
1.5.2 beta with RTE 2.02 v1.5.2.beta release
Wed, 15 Jan 2020 13:41:01 +0100, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/Improment_NVM (pull request #37)
Wed, 15 Jan 2020 10:53:15 +0000, by heinrichsweikamp
merged default into Improvment_NVM Improment_NVM
Tue, 14 Jan 2020 21:52:15 +0100, by Ideenmodellierer
Added compile switch for restoring of last known date after power lost: Improment_NVM
Tue, 14 Jan 2020 21:38:45 +0100, by ideenmodellierer
Bugfix Flipdisplay Gauge and Apnoe mode: Improment_NVM
Tue, 14 Jan 2020 21:10:37 +0100, by ideenmodellierer
Bugfix: Warnings displayed in Gauge Mode: Improment_NVM
Tue, 14 Jan 2020 21:08:45 +0100, by ideenmodellierer
Bugfix: Limit log length in case of corrupted sample storage: Improment_NVM
Mon, 13 Jan 2020 20:27:57 +0100, by ideenmodellierer
Bugfix display compass calibration frozen: Improment_NVM
Sun, 12 Jan 2020 21:33:13 +0100, by ideenmodellierer
Restore last known date: After a power off RTC looses time data and restarts in the year 2000. Code will fix this date to the year 2016. This change will set the date to the last known date of the operation hour counter Improment_NVM
Sun, 12 Jan 2020 19:55:22 +0100, by ideenmodellierer
Bugfix invalid voltage / temperatur after coldstart: Improment_NVM
Sun, 12 Jan 2020 19:50:14 +0100, by ideenmodellierer
Bugfix parallel call of external flash functions: Improment_NVM
Sun, 12 Jan 2020 18:06:59 +0100, by ideenmodellierer
Bugfix Min max values for device data checks: Improment_NVM
Sun, 12 Jan 2020 17:57:11 +0100, by ideenmodellierer
Bugfix Display of Sensor values: Improment_NVM
Sun, 12 Jan 2020 17:47:02 +0100, by ideenmodellierer
Bugfix: display of time of minimum voltag: Improment_NVM
Sun, 12 Jan 2020 17:45:36 +0100, by ideenmodellierer
We got one report of false/freezd depth reading when jumping into 2m depth
Wed, 08 Jan 2020 15:35:15 +0100, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/ImproveBluetooth (pull request #36)
Sun, 05 Jan 2020 14:57:50 +0000, by heinrichsweikamp
merged default into ImproveBluetooth ImproveBluetooth
Sun, 29 Dec 2019 09:42:16 +0100, by Ideenmodellierer
Added retry through power off/on cycle: ImproveBluetooth
Sat, 28 Dec 2019 19:42:04 +0100, by ideenmodellierer
Revert change to keep connection open in case of BlueMod messages: ImproveBluetooth
Sat, 21 Dec 2019 20:21:26 +0100, by ideenmodellierer
Bugfix: Merge / cleanup problem: ImproveBluetooth
Mon, 02 Dec 2019 22:03:05 +0100, by ideenmodellierer
Added missing enum for configuration states ImproveBluetooth
Sun, 01 Dec 2019 19:55:15 +0100, by ideenmodellierer
Added function for BlueMod configuration: ImproveBluetooth
Tue, 26 Nov 2019 22:12:25 +0100, by ideenmodellierer
Added start of module configuration after eache modul power on ImproveBluetooth
Tue, 26 Nov 2019 21:17:57 +0100, by ideenmodellierer
Added start of module configuration after eache modul power on ImproveBluetooth
Tue, 26 Nov 2019 21:16:36 +0100, by ideenmodellierer
Configurate FlowCntrl Pins as noPull ImproveBluetooth
Tue, 26 Nov 2019 21:14:58 +0100, by ideenmodellierer
Bugfix negativ ascend bar: ImproveBluetooth
Tue, 26 Nov 2019 18:13:26 +0100, by ideenmodellierer
Move Constants and libm to start of firmware ROM block: ImproveBluetooth
Tue, 26 Nov 2019 18:02:48 +0100, by ideenmodellierer
Merged in janlmulder/ostc4/maintain-1 (pull request #35)
Mon, 02 Dec 2019 07:56:47 +0000, by heinrichsweikamp
Fix case for case sensitive OS maintain-1
Sun, 01 Dec 2019 17:28:35 +0100, by Jan Mulder
Added tag v1.5.1 release for changeset afa55a50cc72 maintain-1
Sun, 01 Dec 2019 17:12:27 +0100, by Jan Mulder
Merged in Ideenmodellierer/ostc4/MotionDetection (pull request #34)
Sun, 24 Nov 2019 15:46:58 +0000, by heinrichsweikamp
Added key direction awarness to t3, t5 and t6 views: MotionDetection
Mon, 21 Oct 2019 21:16:53 +0200, by ideenmodellierer
Finetune parameter for detection of small sectors as used for the pitch detection MotionDetection
Mon, 21 Oct 2019 18:37:43 +0200, by ideenmodellierer
Consider number of available t3 views in sector handling: MotionDetection
Thu, 17 Oct 2019 23:09:17 +0200, by ideenmodellierer
Combine variables in a structure to improve readability of code MotionDetection
Thu, 17 Oct 2019 21:15:42 +0200, by ideenmodellierer
merge default MotionDetection
Thu, 10 Oct 2019 22:26:03 +0200, by Ideenmodellierer
Simplified pitch detection state machine: MotionDetection
Thu, 10 Oct 2019 22:11:59 +0200, by ideenmodellierer
Minor code cleanup MotionDetection
Thu, 10 Oct 2019 22:09:52 +0200, by ideenmodellierer
Added missing customerview selection MotionDetection
Mon, 16 Sep 2019 22:49:34 +0200, by ideenmodellierer
Incremented "idle window" for scroll detection MotionDetection
Mon, 16 Sep 2019 22:46:24 +0200, by ideenmodellierer
Motion events effect custom view in dive mode only MotionDetection
Mon, 16 Sep 2019 20:57:40 +0200, by ideenmodellierer
Added string for Empty/ Debug custom view selection MotionDetection
Mon, 16 Sep 2019 20:21:06 +0200, by ideenmodellierer
Use Enum values for initialization and setting check: MotionDetection
Tue, 10 Sep 2019 20:51:55 +0200, by ideenmodellierer
Removed some warnings MotionDetection
Sun, 08 Sep 2019 13:45:43 +0200, by ideenmodellierer
Add scroll event by pitch angle detection: MotionDetection
Sun, 08 Sep 2019 13:45:17 +0200, by ideenmodellierer
merged default into MotionDetection MotionDetection
Mon, 19 Aug 2019 17:50:55 +0200, by Ideenmodellierer
Added parameter for number of sectors to be defined MotionDetection
Mon, 19 Aug 2019 17:39:47 +0200, by ideenmodellierer
Changed function names from shake to pitch and improved detection function: Shake might be confusing for people reading the code because pitch values are ased for calculation => changed name to pitch to be more transparent MotionDetection
Tue, 13 Aug 2019 21:13:54 +0200, by ideenmodellierer
Added a function to count the active custom views. MotionDetection
Tue, 13 Aug 2019 21:12:17 +0200, by ideenmodellierer
Added menu item for motion detection. There are several possibility to use motion detection for user action input. To select of the a new menu entry has been added to the Sys2 =>Custom View Menu (Variables in german) MotionDetection
Tue, 13 Aug 2019 21:10:46 +0200, by ideenmodellierer
Merge default MotionDetection
Sat, 20 Jul 2019 21:42:45 +0200, by Ideenmodellierer
Fix misalignment of do while loop MotionDetection
Mon, 17 Jun 2019 19:56:38 +0200, by ideenmodellierer
Bugfix: selection of current view not working MotionDetection
Mon, 17 Jun 2019 19:53:01 +0200, by ideenmodellierer
Update call of motion detection function MotionDetection
Mon, 17 Jun 2019 19:47:07 +0200, by ideenmodellierer
Reworked detection function MotionDetection
Mon, 17 Jun 2019 19:46:18 +0200, by ideenmodellierer
Parameter update MotionDetection
Tue, 11 Jun 2019 05:31:07 +0200, by Ideenmodellierer
Pass action to customer vie update function. MotionDetection
Tue, 11 Jun 2019 05:30:09 +0200, by Ideenmodellierer
Added trigger of middle button action in case of a detected shake MotionDetection
Fri, 24 May 2019 22:01:46 +0200, by ideenmodellierer
Added new files for motion detection (shaking) detection MotionDetection
Fri, 24 May 2019 22:00:38 +0200, by ideenmodellierer
Add Support for new end-2019 hardware:
Sun, 24 Nov 2019 16:08:29 +0100, by heinrichsweikamp
Add Support for new end-2019 hardware:
Sat, 23 Nov 2019 18:39:50 +0100, by heinrichsweikamp
Add Support for new end-2019 hardware:
Sat, 23 Nov 2019 15:36:38 +0100, by heinrichsweikamp
Make a FW 1.5.1 / RTE 2.0 binary for testing v1.5.1 release
Wed, 09 Oct 2019 20:05:47 +0200, by heinrichsweikamp
Merged in janlmulder/ostc4/fix-merge-mess (pull request #33)
Wed, 09 Oct 2019 07:08:43 +0000, by heinrichsweikamp
Added tag v1.5.0 release for changeset 143fe85f82a2 fix-merge-mess
Tue, 08 Oct 2019 16:41:57 +0200, by Jan Mulder
Fix merge problem fix-merge-mess
Tue, 08 Oct 2019 16:35:45 +0200, by Jan Mulder
Merge
Sun, 06 Oct 2019 14:12:41 +0200, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/FlightMode_Improvment (pull request #32)
Sun, 06 Oct 2019 11:58:36 +0000, by heinrichsweikamp
Decrease ManualExitDiveCounter in surface mode FlightMode_Improvment
Thu, 03 Oct 2019 21:39:28 +0200, by ideenmodellierer
Minor changes to debug view FlightMode_Improvment
Thu, 03 Oct 2019 21:34:52 +0200, by ideenmodellierer
Added option to manually leave dive mode to system menu FlightMode_Improvment
Thu, 03 Oct 2019 21:33:47 +0200, by ideenmodellierer
Added function to support manuel exit of dive mode FlightMode_Improvment
Thu, 03 Oct 2019 21:30:16 +0200, by ideenmodellierer
Added function to evaluate the state of the surface pressure history memory FlightMode_Improvment
Thu, 03 Oct 2019 21:26:46 +0200, by ideenmodellierer
Removed not used wireless menu items FlightMode_Improvment
Tue, 01 Oct 2019 19:58:58 +0200, by ideenmodellierer
Added compile switch to enable debug view option in system menu FlightMode_Improvment
Tue, 01 Oct 2019 19:43:30 +0200, by ideenmodellierer
Removed averaging of pressure and temperatur values FlightMode_Improvment
Tue, 01 Oct 2019 19:13:41 +0200, by ideenmodellierer
change max. allowed surface pressure to 1030hPa (As in the small OSTC)
Sun, 06 Oct 2019 14:07:51 +0200, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/PressureMeasure_Improvment (pull request #31)
Mon, 19 Aug 2019 11:42:31 +0000, by heinrichsweikamp
Apply averaging to pressure measurement: In pre versions calculated pressure value jittered +/-10hPa. Since we measure the pressure several time a second but only use one value a second, calc average including not used values PressureMeasure_Improvment
Sat, 17 Aug 2019 19:03:47 +0200, by ideenmodellierer
Added function to avoid divemode activation during Landing: PressureMeasure_Improvment
Sat, 17 Aug 2019 18:57:15 +0200, by ideenmodellierer
Set Max value for pressure offset to 50mBar (20mBar before) PressureMeasure_Improvment
Sat, 17 Aug 2019 18:47:08 +0200, by ideenmodellierer
Show actual instead of surface (30minute old) pressure if the actual differs significant (e.g. in plane or during pressure testing) PressureMeasure_Improvment
Sat, 17 Aug 2019 18:44:43 +0200, by ideenmodellierer
Use average calculation for pressure: precondition was that pressure values jittered +- 10 HPa from one capture (once a second) to the other. Basically pressure is measured several times a second => using these values in an additional history calculation reduces the jitter down to +-1 per second PressureMeasure_Improvment
Tue, 13 Aug 2019 21:46:26 +0200, by ideenmodellierer
building a 1.5 v1.5.0 release
Sun, 04 Aug 2019 11:01:06 +0200, by heinrichsweikamp
add update files for testing purposes
Sat, 20 Jul 2019 10:44:01 +0200, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/I2C_Improvment (pull request #30)
Thu, 18 Jul 2019 14:26:56 +0000, by heinrichsweikamp
Added plausibility check for pressure values I2C_Improvment
Wed, 17 Jul 2019 22:43:51 +0200, by ideenmodellierer
Added check of configuration. I2C_Improvment
Wed, 17 Jul 2019 22:43:16 +0200, by ideenmodellierer
Improved startup robustness I2C_Improvment
Wed, 17 Jul 2019 22:42:55 +0200, by ideenmodellierer
Set I2C speed to 88kHz, use digital filter only and reworked idle clock recovery I2C_Improvment
Wed, 17 Jul 2019 22:42:15 +0200, by ideenmodellierer
Deactivated internal pullups and I2C interrupt callback I2C_Improvment
Wed, 17 Jul 2019 22:41:31 +0200, by ideenmodellierer
Merged in janlmulder/ostc4/fix-batt-1 (pull request #29)
Mon, 01 Jul 2019 14:18:39 +0000, by heinrichsweikamp
bugfix: implement battery at end in dive header fix-batt-1
Thu, 20 Jun 2019 14:24:57 +0200, by Jan Mulder
increase RTE to 1.9 and Firmware to 1.4.9 beta
Sun, 30 Jun 2019 22:12:15 +0200, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/O2_SensorSync (pull request #28)
Sun, 30 Jun 2019 19:52:46 +0000, by heinrichsweikamp
Added start of frame detection for HUD data O2_SensorSync
Sun, 30 Jun 2019 21:25:58 +0200, by ideenmodellierer
Moved indication variable for received HUD data to tCCR file. O2_SensorSync
Sun, 30 Jun 2019 21:18:05 +0200, by ideenmodellierer
Merged in janlmulder/ostc4/fix-version (pull request #27)
Wed, 19 Jun 2019 13:12:25 +0000, by heinrichsweikamp
bugfix: correct packed main version number in dive header fix-version
Wed, 19 Jun 2019 14:31:50 +0200, by Jan Mulder
Merged in Ideenmodellierer/ostc4/Bugfix_Flip_FirmwareUpdate (pull request #26)
Wed, 19 Jun 2019 13:12:01 +0000, by heinrichsweikamp
Resolved warning Bugfix_Flip_FirmwareUpdate
Mon, 17 Jun 2019 21:47:54 +0200, by ideenmodellierer
Bugfix text display in update mode (flipped display) and reduction of timeout in case of a failed firmware update Bugfix_Flip_FirmwareUpdate
Mon, 17 Jun 2019 21:47:33 +0200, by ideenmodellierer
Bugfix Overview, O2 values and mV in flip display mode Bugfix_Flip_FirmwareUpdate
Mon, 17 Jun 2019 21:47:19 +0200, by ideenmodellierer
Reinitialize logos after flip of display Bugfix_Flip_FirmwareUpdate
Mon, 17 Jun 2019 21:46:56 +0200, by ideenmodellierer
Minor: Remove unused compass header file. The LSM303DLHC is not used in any hardware sold.
Sat, 01 Jun 2019 10:12:15 +0200, by heinrichsweikamp
Merged in janlmulder/ostc4/cleanup-4 (pull request #25)
Fri, 31 May 2019 06:22:50 +0000, by heinrichsweikamp
bugfix: make stopwatch and divetime run in sync cleanup-4
Wed, 29 May 2019 14:02:27 +0200, by Jan Mulder
Make dive mode detection more advanced cleanup-4
Sun, 26 May 2019 10:09:22 +0200, by Jan Mulder
cleanup: factor out SHelper typedef (and more) cleanup-4
Fri, 24 May 2019 09:29:29 +0200, by Jan Mulder
cleanup: introduce function setAvgDepth cleanup-4
Fri, 24 May 2019 09:02:46 +0200, by Jan Mulder
cleanup: factor out unused stopwatch code cleanup-4
Wed, 22 May 2019 22:22:15 +0200, by Jan Mulder
bugfix, cleanup: do not clip depth to 0 cleanup-4
Wed, 22 May 2019 14:39:04 +0200, by Jan Mulder
bugfix, consistency: show deco/NDL really after 1 minute divetime cleanup-4
Tue, 21 May 2019 11:11:05 +0200, by Jan Mulder
bugfix, simulator: fix the 1 sec difference between stopwatch and divetime cleanup-4
Mon, 20 May 2019 13:06:02 +0200, by Jan Mulder
bugfix, cleanup: simplify stopwatch logic and fix fallout cleanup-4
Mon, 20 May 2019 12:57:31 +0200, by Jan Mulder
bugfix, cleanup: keep both is_ambient_pressure_close_to_surface in sync cleanup-4
Mon, 20 May 2019 10:13:44 +0200, by Jan Mulder
cleanup, RTE: factor out scheduleCheck_pressure_reached_dive_mode_level cleanup-4
Mon, 20 May 2019 10:05:27 +0200, by Jan Mulder
cleanup: remove commented/unused code, make static cleanup-4
Fri, 17 May 2019 21:19:04 +0200, by Jan Mulder
Merged in janlmulder/ostc4/cleanup-3 (pull request #24)
Fri, 17 May 2019 06:38:56 +0000, by heinrichsweikamp
Bugfix: fix drawing of CCR bailout profile cleanup-3
Thu, 16 May 2019 14:02:46 +0200, by Jan Mulder
cleanup: remove unused code, make static, remove commented code cleanup-3
Thu, 16 May 2019 08:56:15 +0200, by Jan Mulder
Possible bugfix: do not use bitwise and (&) cleanup-3
Thu, 16 May 2019 08:54:33 +0200, by Jan Mulder
Merged in janlmulder/ostc4/div-fixes-6 (pull request #23)
Mon, 13 May 2019 13:37:34 +0000, by heinrichsweikamp
Added tag v1.4.8 release for changeset ba9d99a2e310 div-fixes-6
Sun, 12 May 2019 09:45:32 +0200, by Jan Mulder
bugfix, consistency: show deco, NDL after 1 minute div-fixes-6
Thu, 02 May 2019 10:05:28 +0200, by Jan Mulder
translate: nullzeit -> ndl div-fixes-6
Thu, 02 May 2019 09:24:54 +0200, by Jan Mulder
Deco Models: limit NDL to 240 minutes div-fixes-6
Thu, 02 May 2019 09:16:07 +0200, by Jan Mulder
VPM, cleanup: 1st round div-fixes-6
Thu, 02 May 2019 08:43:07 +0200, by Jan Mulder
cleanup: remove unused code div-fixes-6
Mon, 29 Apr 2019 19:45:25 +0200, by Jan Mulder
cleanup: no useless checks for simulator state div-fixes-6
Mon, 29 Apr 2019 19:43:05 +0200, by Jan Mulder
Update the release file for testing. Rev 286 did not include the 1.4.8 (non-beta) firmware. v1.4.8 release
Mon, 06 May 2019 15:45:19 +0200, by heinrichsweikamp
Minor: Some Texts fixed, allign RTErequired* values with RTE firmware
Mon, 06 May 2019 09:00:58 +0200, by heinrichsweikamp
add update files for testing purposes
Sun, 05 May 2019 11:06:02 +0200, by heinrichsweikamp
Merged in janlmulder/ostc4/ndl-in-logbook (pull request #22)
Thu, 02 May 2019 11:12:25 +0000, by heinrichsweikamp
Bugfix: write NDL in logbook correctly ndl-in-logbook
Thu, 02 May 2019 13:08:17 +0200, by Jan Mulder
translate some comments into english
Wed, 01 May 2019 14:45:47 +0200, by heinrichsweikamp
Fix typos (There are still many...)
Wed, 01 May 2019 14:39:46 +0200, by heinrichsweikamp
Make RTE show as 1.8.0 beta, add update files for testing purposes
Mon, 29 Apr 2019 19:25:24 +0200, by heinrichsweikamp
add update files for testing purposes
Sun, 28 Apr 2019 17:57:39 +0200, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/IPC_Sync_Improvment_3 (pull request #21)
Sun, 28 Apr 2019 15:54:46 +0000, by heinrichsweikamp
Rework SPI error handling. IPC_Sync_Improvment_3
Sun, 28 Apr 2019 10:16:38 +0200, by ideenmodellierer
Rework pressure/ temperature data aquisition IPC_Sync_Improvment_3
Sun, 28 Apr 2019 10:06:27 +0200, by ideenmodellierer
Do not mark data as valid if devicedata is received. IPC_Sync_Improvment_3
Sun, 28 Apr 2019 09:54:43 +0200, by ideenmodellierer
add update files for testing purposes, bump to 1.4.8 beta / RTE 1.7.1 beta
Sun, 28 Apr 2019 09:41:43 +0200, by heinrichsweikamp
Merged in janlmulder/ostc4/write-from-sim (pull request #20)
Sun, 28 Apr 2019 07:05:23 +0000, by heinrichsweikamp
cleanup: simplify stateUsed usage write-from-sim
Sat, 27 Apr 2019 12:27:46 +0200, by Jan Mulder
cleanup: also write gas and setpoint changes in simulator mode write-from-sim
Sat, 27 Apr 2019 09:32:16 +0200, by Jan Mulder
feature, debug: make simulator write a logbook entry write-from-sim
Wed, 24 Apr 2019 17:10:51 +0200, by Jan Mulder
cleanup: do not pass large struct by value write-from-sim
Tue, 23 Apr 2019 21:03:24 +0200, by Jan Mulder
cleanup: make things static where possible. write-from-sim
Tue, 23 Apr 2019 17:41:20 +0200, by Jan Mulder
Merged in Ideenmodellierer/ostc4/IPC_Sync_Improvment_2 (pull request #18)
Fri, 26 Apr 2019 10:36:11 +0000, by heinrichsweikamp
Added batch to copy bins from release folder IPC_Sync_Improvment_2
Sun, 14 Apr 2019 14:27:32 +0200, by ideenmodellierer
Increase SPI com timeout for cold start and wake up IPC_Sync_Improvment_2
Sun, 14 Apr 2019 14:22:41 +0200, by ideenmodellierer
Sync to Main 100ms time stamp & added Reinitialization of globals after startup IPC_Sync_Improvment_2
Sun, 14 Apr 2019 11:43:29 +0200, by ideenmodellierer
Forward 100ms time stamp to RTE and handle logbook in main loop IPC_Sync_Improvment_2
Sun, 14 Apr 2019 11:38:14 +0200, by ideenmodellierer
Merged in janlmulder/ostc4/bm-3 (pull request #19)
Tue, 23 Apr 2019 14:21:32 +0000, by heinrichsweikamp
Bugfix: do not reset saturation on surfacing bm-3
Tue, 23 Apr 2019 13:05:20 +0200, by Jan Mulder
Added tag V1.4.7 release for changeset 1b9be6040d82 bm-3
Tue, 23 Apr 2019 09:25:18 +0200, by Jan Mulder
feature: allow new saturation to be set in lower left corner bm-3
Mon, 15 Apr 2019 17:35:47 +0200, by Jan Mulder
Buehlmann: factor out another global gDecotable bm-3
Fri, 12 Apr 2019 22:00:07 +0200, by Jan Mulder
Buehlmann: factor out gNDL and gTTS bm-3
Fri, 12 Apr 2019 21:04:52 +0200, by Jan Mulder
Buehlmann: trivial performance improvement (NDL) bm-3
Fri, 12 Apr 2019 19:05:49 +0200, by Jan Mulder
Buehlmann: cleanup, factor out pBuDiveSettings bm-3
Fri, 12 Apr 2019 15:26:14 +0200, by Jan Mulder
Buehlmann: cleanup, remove global pDecolistBuehlmann bm-3
Fri, 12 Apr 2019 14:46:48 +0200, by Jan Mulder
Buehlmann: cleanup, whitespace, static bm-3
Fri, 12 Apr 2019 10:43:52 +0200, by Jan Mulder
Minor: Typo fixed in bootloader screen V1.4.7 release
Sat, 13 Apr 2019 14:36:33 +0200, by heinrichsweikamp
Merged in janlmulder/ostc4/bm-2 (pull request #17)
Fri, 12 Apr 2019 07:22:14 +0000, by heinrichsweikamp
Buelmann: new implementation for ceiling bm-2
Thu, 11 Apr 2019 17:48:48 +0200, by Jan Mulder
Merged in janlmulder/ostc4/bm-1 (pull request #16)
Thu, 11 Apr 2019 10:26:22 +0000, by heinrichsweikamp
Fix stupid commit error bm-1
Wed, 10 Apr 2019 17:55:46 +0200, by Jan Mulder
feature: Relative GF to Saturation renames bm-1
Tue, 09 Apr 2019 16:30:21 +0200, by Jan Mulder
feature: replace Relative GF by saturation, computational only bm-1
Tue, 09 Apr 2019 15:38:31 +0200, by Jan Mulder
add update files for testing purposes
Wed, 10 Apr 2019 11:04:56 +0200, by heinrichsweikamp
Merged in janlmulder/ostc4/div-fixes-5 (pull request #15)
Tue, 09 Apr 2019 08:52:44 +0000, by heinrichsweikamp
debug: add SPI error counter to compass calibration div-fixes-5
Mon, 08 Apr 2019 12:35:59 +0200, by Jan Mulder
Comply to datasheet when resetting battery gauge registers div-fixes-5
Mon, 08 Apr 2019 12:02:07 +0200, by Jan Mulder
cleanup: factor out I2C1_Status() and cleanup type div-fixes-5
Mon, 08 Apr 2019 11:18:40 +0200, by Jan Mulder
Improvement SPI stability/recoverability div-fixes-5
Mon, 08 Apr 2019 11:49:13 +0200, by Jan Mulder
cleanup: factor out dataSendToSlaveStopEval div-fixes-5
Mon, 08 Apr 2019 10:35:29 +0200, by Jan Mulder
cleanup, bugfix: do not mask I2C_SystemStatus with local variable div-fixes-5
Mon, 08 Apr 2019 10:16:17 +0200, by Jan Mulder
Bugfix: do not show NDL in bigscreen mode when zero div-fixes-5
Sat, 06 Apr 2019 20:35:21 +0200, by Jan Mulder
Minor: translating some comments and variable names into english, some cleanup in tComm.c
Sat, 06 Apr 2019 09:41:14 +0200, by heinrichsweikamp
add update files for testing purposes
Sat, 06 Apr 2019 09:11:39 +0200, by heinrichsweikamp
Merged in janlmulder/ostc4/div-fixes-4-1 (pull request #14)
Sat, 06 Apr 2019 07:01:21 +0000, by heinrichsweikamp
cleanup, bugfix: do not exit simulator on 5h dive time div-fixes-4-1
Fri, 05 Apr 2019 09:12:04 +0200, by Jan Mulder
Bugfix: make date/time setting work over reboots div-fixes-4-1
Wed, 03 Apr 2019 21:11:56 +0200, by Jan Mulder
cleanup: do not re-implement a standard function div-fixes-4-1
Wed, 03 Apr 2019 14:33:12 +0200, by Jan Mulder
cleanup: make return void when never used div-fixes-4-1
Wed, 03 Apr 2019 14:16:59 +0200, by Jan Mulder
cleanup: fix recent extra compiler warnings div-fixes-4-1
Tue, 02 Apr 2019 15:11:42 +0200, by Jan Mulder
Bugfix: set battery percentage correctly after RTE update div-fixes-4-1
Tue, 02 Apr 2019 14:53:15 +0200, by Jan Mulder
add update files for testing purposes
Tue, 02 Apr 2019 18:18:22 +0200, by heinrichsweikamp
Merged in janlmulder/ostc4/div-fixes-3 (pull request #13)
Mon, 01 Apr 2019 19:19:04 +0000, by heinrichsweikamp
cleanup: random set of cleanups div-fixes-3
Mon, 01 Apr 2019 15:50:41 +0200, by Jan Mulder
Bugfix, deco: fix 2 (small) problems with calculated ceiling div-fixes-3
Sun, 31 Mar 2019 19:35:51 +0200, by Jan Mulder
Bugfix, minor: properly alternate VPM/Buhlmann in deco loop div-fixes-3
Sun, 31 Mar 2019 15:14:06 +0200, by Jan Mulder
Bugfix: correct presentation error in tissues custom view div-fixes-3
Fri, 29 Mar 2019 14:00:43 +0100, by Jan Mulder
Merged in Ideenmodellierer/ostc4/Improve_IPC_Sync (pull request #12)
Mon, 01 Apr 2019 09:01:09 +0000, by heinrichsweikamp
Added schedule point for functions executed once in a second Improve_IPC_Sync
Sun, 31 Mar 2019 15:49:47 +0200, by ideenmodellierer
Resolved some minor warnings Improve_IPC_Sync
Sun, 31 Mar 2019 15:44:56 +0200, by ideenmodellierer
Splitted 120 seconds UART timeout into chunks of 500ms Improve_IPC_Sync
Sun, 31 Mar 2019 15:44:12 +0200, by ideenmodellierer
Moved display refresh and button action function from tim callback to main loop Improve_IPC_Sync
Sun, 31 Mar 2019 15:39:44 +0200, by ideenmodellierer
Merged in janlmulder/ostc4/edit-fix (pull request #11)
Thu, 28 Mar 2019 13:05:29 +0000, by heinrichsweikamp
Bugfix, trivial: correctly present avg depth in overview custom edit-fix
Thu, 28 Mar 2019 09:54:29 +0100, by Jan Mulder
Bugfix: handle rounding of TTS and future TTS consistently edit-fix
Thu, 28 Mar 2019 08:26:17 +0100, by Jan Mulder
Bugfix, trivial: do not visit 9 on first digit for setpoint edit-fix
Wed, 27 Mar 2019 15:12:26 +0100, by Jan Mulder
Merged in janlmulder/ostc4/cv-persistent (pull request #10)
Tue, 26 Mar 2019 22:23:26 +0000, by heinrichsweikamp
New feature: do not show sensor customviews when no sensors attached cv-persistent
Tue, 26 Mar 2019 16:02:22 +0100, by Jan Mulder
New feature: make selected customviews persistent cv-persistent
Tue, 26 Mar 2019 13:00:15 +0100, by Jan Mulder
Merged in Ideenmodellierer/ostc4/ImprovmentSPI (pull request #9)
Sun, 24 Mar 2019 22:09:37 +0000, by heinrichsweikamp
Update SPI error display and handling ImprovmentSPI
Sun, 24 Mar 2019 22:57:28 +0100, by ideenmodellierer
Introduce scheduler function ImprovmentSPI
Sun, 24 Mar 2019 22:53:17 +0100, by ideenmodellierer
Moved EvaluateButton into 100ms callback ImprovmentSPI
Sun, 24 Mar 2019 22:51:15 +0100, by ideenmodellierer
Deleted duplicated header file (keep the one stored in common) ImprovmentSPI
Sun, 24 Mar 2019 22:48:49 +0100, by ideenmodellierer
Starting 'ImprovmentSPI' branch ImprovmentSPI
Sat, 23 Mar 2019 21:35:29 +0100, by ideenmodellierer
merge fork
Sat, 23 Mar 2019 21:32:16 +0100, by Ideenmodellierer
Merged heinrichsweikamp/ostc4 into default
Sun, 17 Mar 2019 19:16:59 +0100, by Thorsten
Merged Cleanup_Compass_Wireless into default
Sat, 16 Mar 2019 19:58:52 +0000, by Thorsten
Merged in janlmulder/ostc4/div-fixes-cleaup-2 (pull request #8)
Fri, 22 Mar 2019 08:15:30 +0000, by heinrichsweikamp
Bugfix: fix initial CNS data in the logbook header div-fixes-cleaup-2
Fri, 22 Mar 2019 08:36:39 +0100, by Jan Mulder
cleanup: another cleanup session (data_exchange_main.c) div-fixes-cleaup-2
Thu, 21 Mar 2019 15:28:47 +0100, by Jan Mulder
cleanup: fix (harmless) use before assign div-fixes-cleaup-2
Thu, 21 Mar 2019 11:41:59 +0100, by Jan Mulder
Bugfix, minor: color the overview customview correctly div-fixes-cleaup-2
Wed, 20 Mar 2019 16:24:10 +0100, by Jan Mulder
Merged in janlmulder/ostc4/div-fixes-cleanup-1 (pull request #7)
Tue, 19 Mar 2019 15:43:38 +0000, by heinrichsweikamp
cleanup: more trivial cleanup (logbook.c/h) div-fixes-cleanup-1
Tue, 19 Mar 2019 11:42:00 +0100, by Jan Mulder
Bugfix: show proper dive mode div-fixes-cleanup-1
Sat, 16 Mar 2019 21:52:06 +0100, by Jan Mulder
cleanup: fix compiler warning div-fixes-cleanup-1
Sat, 16 Mar 2019 21:08:18 +0100, by Jan Mulder
cleanup: remove unused include file t9.h div-fixes-cleanup-1
Sat, 16 Mar 2019 21:02:10 +0100, by Jan Mulder
Merged in janlmulder/ostc4/avg-temp (pull request #6)
Fri, 15 Mar 2019 15:48:53 +0000, by heinrichsweikamp
Bugfix: average temperature on arrival from RTE instead of display time avg-temp
Fri, 15 Mar 2019 15:04:57 +0100, by Jan Mulder
Merged in janlmulder/ostc4/cleanup-2 (pull request #5)
Fri, 15 Mar 2019 12:55:58 +0000, by heinrichsweikamp
cleanup: forgotten cleanup from 9da7dd50e2ec cleanup-2
Fri, 15 Mar 2019 12:53:14 +0100, by Jan Mulder
cleanup: remove obsolete code, make static, etc. cleanup-2
Fri, 15 Mar 2019 12:39:28 +0100, by Jan Mulder
Merged in Ideenmodellierer/ostc4/Cleanup_Compass_Wireless (pull request #4)
Fri, 15 Mar 2019 08:22:16 +0000, by heinrichsweikamp
Cleanup compiler warnings Cleanup_Compass_Wireless
Thu, 14 Mar 2019 20:44:23 +0100, by ideenmodellierer
Cleanup compiler warnings Cleanup_Compass_Wireless
Thu, 14 Mar 2019 20:44:03 +0100, by ideenmodellierer
Resolve fixme comments Cleanup_Compass_Wireless
Thu, 14 Mar 2019 20:43:47 +0100, by ideenmodellierer
Removed not suppoted wireless feature Cleanup_Compass_Wireless
Wed, 13 Mar 2019 21:51:25 +0100, by ideenmodellierer
Removed not used compass code Cleanup_Compass_Wireless
Wed, 13 Mar 2019 21:49:25 +0100, by ideenmodellierer
Starting 'Cleanup_Compass_Wireless' branch Cleanup_Compass_Wireless
Wed, 13 Mar 2019 20:53:05 +0100, by ideenmodellierer
Minor: Replace stupid "Sleep Sleep Sleep" message with something more meaningful
Wed, 13 Mar 2019 20:51:50 +0100, by heinrichsweikamp
Merged in janlmulder/ostc4/max-depth (pull request #3)
Tue, 12 Mar 2019 15:04:19 +0000, by heinrichsweikamp
cleanup: do not assign to same max-depth
Mon, 11 Mar 2019 20:20:17 +0100, by Jan Mulder
cleanup: remove unused code max-depth
Mon, 11 Mar 2019 19:57:51 +0100, by Jan Mulder
Bugfix: make max depth move with current depth (part 2) max-depth
Mon, 11 Mar 2019 19:54:20 +0100, by Jan Mulder
Bugfix: make max depth move with current depth (part 1) max-depth
Mon, 11 Mar 2019 19:48:57 +0100, by Jan Mulder
Minor: Button defaults, release date adjusted, use SPI_SHOW_SYNC_STATS
Sun, 10 Mar 2019 20:30:42 +0100, by heinrichsweikamp
Merged in janlmulder/ostc4/cleanup-1 (pull request #2)
Sun, 10 Mar 2019 15:39:55 +0000, by heinrichsweikamp
Fix accidentally pushed local code cleanup-1
Sun, 10 Mar 2019 10:46:48 +0100, by Jan Mulder
Bugfix: highlight the menu underline correctly on selected state cleanup-1
Sun, 10 Mar 2019 10:09:58 +0100, by Jan Mulder
Close branch linux-build. linux-build
Fri, 08 Mar 2019 19:26:36 +0000, by Jan Mulder
cleanup: local data and functions can be static (tMenu) cleanup-1
Fri, 08 Mar 2019 13:47:52 +0100, by Jan Mulder
cleanup: get rid of some compile warnings cleanup-1
Thu, 07 Mar 2019 21:52:23 +0100, by Jan Mulder
Minor: Some documentation for new hardware
Fri, 08 Mar 2019 10:31:32 +0100, by heinrichsweikamp
Merged in janlmulder/ostc4/linux-build (pull request #1)
Thu, 07 Mar 2019 14:15:33 +0000, by heinrichsweikamp
Add Linux pack script linux-build
Thu, 21 Feb 2019 16:56:08 +0100, by Jan Mulder
OSTC4pack_V4: do not hard code output filename for fonts linux-build
Thu, 21 Feb 2019 10:29:26 +0100, by Jan Mulder
Add missing file for self build pack tools linux-build
Thu, 21 Feb 2019 10:01:36 +0100, by Jan Mulder
Merge with FlipDisplay
Thu, 07 Mar 2019 15:06:43 +0100, by heinrichsweikamp
Fix for flipped display FlipDisplay
Sun, 03 Mar 2019 21:13:31 +0100, by Ideenmodellierer
Bugfix button translation FlipDisplay
Sun, 03 Mar 2019 21:12:06 +0100, by Ideenmodellierer
Binaries for beta testing FlipDisplay
Sun, 03 Mar 2019 19:20:18 +0100, by Ideenmodellierer
Removed special indicator for DMA transfer error FlipDisplay
Sun, 03 Mar 2019 19:18:51 +0100, by Ideenmodellierer
Do hard sync after communication timeout > 1 second FlipDisplay
Sun, 03 Mar 2019 17:46:50 +0100, by Ideenmodellierer
Keep NSS low during SPI transfer only FlipDisplay
Sun, 03 Mar 2019 17:45:39 +0100, by Ideenmodellierer
Added definitions for SPI sequence counter FlipDisplay
Sun, 03 Mar 2019 12:19:47 +0100, by Ideenmodellierer
Moved button evaluation out of interrupt handler FlipDisplay
Sun, 03 Mar 2019 12:18:44 +0100, by Ideenmodellierer
Bugfix ButtonResponsiveness FlipDisplay
Sun, 03 Mar 2019 12:16:54 +0100, by Ideenmodellierer
Place CNS and pressure within the screen (avoid clipping) FlipDisplay
Sat, 02 Mar 2019 17:42:51 +0100, by Ideenmodellierer
Eliminate warnings FlipDisplay
Sat, 02 Mar 2019 17:42:06 +0100, by Ideenmodellierer
Use SPI TX callback to synchronize to main CPU FlipDisplay
Sat, 02 Mar 2019 17:01:06 +0100, by Ideenmodellierer
Forward compass data during calibration mode FlipDisplay
Sat, 02 Mar 2019 16:57:59 +0100, by Ideenmodellierer
RTE Version 1.7 needed because of protocoll and baud rate change FlipDisplay
Sat, 02 Mar 2019 16:56:58 +0100, by Ideenmodellierer
Adjust voltage location FlipDisplay
Thu, 28 Feb 2019 20:05:51 +0100, by Ideenmodellierer
Use one global structure for schedule data FlipDisplay
Thu, 28 Feb 2019 20:05:17 +0100, by Ideenmodellierer
Introduced Token for SPI data exchange FlipDisplay
Thu, 28 Feb 2019 19:38:36 +0100, by Ideenmodellierer
Use one global structure for all schedule counters FlipDisplay
Thu, 28 Feb 2019 19:34:08 +0100, by Ideenmodellierer
Only use data if data frame is valid FlipDisplay
Thu, 28 Feb 2019 19:07:10 +0100, by Ideenmodellierer
Increase prescalar => frame takes about 4ms. FlipDisplay
Thu, 28 Feb 2019 19:03:29 +0100, by Ideenmodellierer
Get version from local memory instead from incoming data FlipDisplay
Thu, 28 Feb 2019 19:02:34 +0100, by Ideenmodellierer
Removed no longer supported scooter code FlipDisplay
Sat, 23 Feb 2019 21:10:51 +0100, by Ideenmodellierer
Only copy data if data connection to RTE is valid FlipDisplay
Tue, 19 Feb 2019 21:48:32 +0100, by Ideenmodellierer
Introduces abort of communication in case of a out of sync DMA transfer FlipDisplay
Tue, 19 Feb 2019 18:20:45 +0100, by Ideenmodellierer
Restore old data copy locations FlipDisplay
Tue, 19 Feb 2019 18:18:37 +0100, by Ideenmodellierer
Removed cyclic (by timer) send on slave side FlipDisplay
Tue, 19 Feb 2019 18:16:59 +0100, by Ideenmodellierer
Intoduced transfer abort function for data exchange recovery FlipDisplay
Tue, 19 Feb 2019 18:15:35 +0100, by Ideenmodellierer
Add compile switch to disable optimization for specific function FlipDisplay
Tue, 19 Feb 2019 18:13:18 +0100, by Ideenmodellierer
Update of configuration and projectfiles to support new library folder structure FlipDisplay
Sun, 17 Feb 2019 21:29:38 +0100, by Ideenmodellierer
Minor changes to improved code quality and to eliminate warnings FlipDisplay
Sun, 17 Feb 2019 21:22:13 +0100, by Ideenmodellierer
Added function to initialise structures with the actual ambient pressure FlipDisplay
Sun, 17 Feb 2019 21:14:09 +0100, by Ideenmodellierer
Added current STM32 standandard libraries in version independend folder structure FlipDisplay
Sun, 17 Feb 2019 21:12:22 +0100, by Ideenmodellierer
Drop old STM32 standard librarey files FlipDisplay
Sun, 17 Feb 2019 21:07:35 +0100, by Ideenmodellierer
build files kittz
Sun, 03 Feb 2019 10:04:27 +0100, by heinrichsweikamp
Change GPIO speed for SPI communication as recommended by STM32 Errata FlipDisplay
Sun, 27 Jan 2019 22:21:01 +0100, by Ideenmodellierer
Change GPIO speed for SPI communication as recommended by STM32 Errata FlipDisplay
Sun, 27 Jan 2019 22:17:16 +0100, by Ideenmodellierer
Added option to build FontPack as static libary which is linked to the Firmware project (to allow separate build settings) FlipDisplay
Sun, 27 Jan 2019 22:01:07 +0100, by Ideenmodellierer
Take care for display orientation if deleting lines FlipDisplay
Sun, 13 Jan 2019 18:59:53 +0100, by Ideenmodellierer
Use 32bit operations for buffer fills FlipDisplay
Sun, 13 Jan 2019 18:58:23 +0100, by Ideenmodellierer
Cleanup warning and disable printf calls FlipDisplay
Tue, 08 Jan 2019 22:31:17 +0100, by Ideenmodellierer
Cleanup writechar pointers FlipDisplay
Sun, 06 Jan 2019 22:33:26 +0100, by Ideenmodellierer
Enlarge text limits to get string displayed completly FlipDisplay
Sun, 06 Jan 2019 22:31:45 +0100, by Ideenmodellierer
Submenus may have 6 items FlipDisplay
Sun, 06 Jan 2019 22:30:35 +0100, by Ideenmodellierer
Added small helper for runtime evaluation FlipDisplay
Sun, 06 Jan 2019 22:27:46 +0100, by Ideenmodellierer
Merge with 68181cd61f2069d061621c2cd2a6afddb7486f5e FlipDisplay
Thu, 03 Jan 2019 19:59:36 +0100, by Ideenmodellierer
Eliminate warnings FlipDisplay
Thu, 03 Jan 2019 18:35:11 +0100, by Ideenmodellierer
Binaries of development snapshot FlipDisplay
Tue, 01 Jan 2019 21:04:01 +0100, by Ideenmodellierer
Added new nvm parameter"FlipDisplay" indicating the screen orientation FlipDisplay
Tue, 01 Jan 2019 21:03:33 +0100, by Ideenmodellierer
Added new nvm parameter"FlipDisplay" indicating the screen orientation FlipDisplay
Tue, 01 Jan 2019 21:03:10 +0100, by Ideenmodellierer
Added option to handled mirrored display to existing functions FlipDisplay
Tue, 01 Jan 2019 21:02:17 +0100, by Ideenmodellierer
Consider computer heading in case of a flipped display FlipDisplay
Tue, 01 Jan 2019 21:00:55 +0100, by Ideenmodellierer
Flip key assigment if needed FlipDisplay
Tue, 01 Jan 2019 21:00:13 +0100, by Ideenmodellierer
Next text ID for display flip FlipDisplay
Tue, 01 Jan 2019 20:59:36 +0100, by Ideenmodellierer
Starting 'FlipDisplay' branch FlipDisplay
Tue, 01 Jan 2019 20:57:41 +0100, by Ideenmodellierer
fix comments kittz
Mon, 24 Dec 2018 16:19:09 +0300, by Dmitry Romanov
Tested and alive. kittz
Mon, 24 Dec 2018 16:15:02 +0300, by Dmitry Romanov
Generalize TEXT of pressure unit kittz
Wed, 28 Nov 2018 09:36:33 +0300, by Dmitry Romanov
hPa instead of mbar, enabled Spanish language kittz
Tue, 27 Nov 2018 18:31:21 +0100, by heinrichsweikamp
globals kittz
Tue, 27 Nov 2018 13:18:59 +0300, by Dmitry Romanov
Stable.fix. kittz
Tue, 27 Nov 2018 12:59:56 +0300, by Dmitry Romanov
Config for debug data kittz
Mon, 26 Nov 2018 15:25:52 +0300, by Dmitry Romanov
+2ms delay kittz
Mon, 26 Nov 2018 13:58:51 +0300, by Dmitry Romanov
fix comments kittz
Mon, 26 Nov 2018 13:49:02 +0300, by Dmitry Romanov
Sorry. Now. kittz
Mon, 26 Nov 2018 13:45:14 +0300, by Dmitry Romanov
Debounce. Bounced buttons fixed. kittz
Mon, 26 Nov 2018 13:42:38 +0300, by Dmitry Romanov
reduce i2c speed and dutycycle for compass stability kittz
Mon, 26 Nov 2018 12:20:31 +0300, by Dmitry Romanov
a bit of kittz
Mon, 26 Nov 2018 11:38:06 +0300, by Dmitry Romanov
Stable to test. button sensitiveness fix. + global_constants. kittz
Mon, 26 Nov 2018 10:50:39 +0300, by Dmitry Romanov
First stable. With minimal button sensitivity fix(for broken buttons) kittz
Mon, 26 Nov 2018 10:13:02 +0300, by Dmitry Romanov
+- stable kittz
Fri, 23 Nov 2018 18:14:56 +0300, by Dmitry Romanov
temp! full cyclic SPI kittz
Fri, 23 Nov 2018 16:52:21 +0300, by Dmitry Romanov
revert kittz
Thu, 22 Nov 2018 12:02:55 +0300, by Dmitry Romanov
tmp kittz
Wed, 21 Nov 2018 13:57:58 +0300, by Dmitry Romanov
fix time&date after wakeup kittz
Wed, 21 Nov 2018 13:12:44 +0300, by Dmitry Romanov
increased interCPU baudrate, cpu2: i2c in SPI1 IRQ kittz
Wed, 21 Nov 2018 12:49:54 +0300, by Dmitry Romanov
Remove unusable code!!! prepare data for SPI in ONLY 1 IRQ!!!! kittz
Wed, 21 Nov 2018 10:25:15 +0300, by Dmitry Romanov
??????? kittz
Tue, 20 Nov 2018 12:27:40 +0300, by Dmitry Romanov
+i2c analog noise filtering kittz
Tue, 20 Nov 2018 12:08:19 +0300, by Dmitry Romanov
Created new branch kittz kittz
Tue, 20 Nov 2018 09:25:17 +0000, by Dmitry Romanov
Added Spanish language
Sat, 06 Oct 2018 15:02:11 +0200, by heinrichsweikamp
Added Fontpack reference project
Thu, 04 Oct 2018 20:49:47 +0200, by Ideenmodellierer
Added script to pack FontPack
Thu, 04 Oct 2018 20:45:12 +0200, by Ideenmodellierer
Starting Firmware 1.4 the fontpack version 1.0 is needed
Thu, 04 Oct 2018 20:44:19 +0200, by Ideenmodellierer
Update Fontpack code to support font moved to upper memory
Thu, 04 Oct 2018 20:42:56 +0200, by Ideenmodellierer
Update version info
Thu, 04 Oct 2018 20:41:21 +0200, by Ideenmodellierer
Move font to upper memory
Thu, 04 Oct 2018 20:40:53 +0200, by Ideenmodellierer
Add definitions for Fonts to be placed in upper flash
Thu, 04 Oct 2018 20:40:21 +0200, by Ideenmodellierer
Merge
Tue, 11 Sep 2018 22:16:05 +0200, by heinrichsweikamp
remove wiki files from repo
Wed, 05 Sep 2018 10:41:48 +0200, by heinrichsweikamp
old (and new) compass support
Tue, 11 Sep 2018 19:29:58 +0200, by heinrichsweikamp
1.3.8 forum release
Thu, 30 Aug 2018 21:48:21 +0200, by heinrichsweikamp
Update image size for 'F'ahrenheit
Wed, 22 Aug 2018 18:54:01 +0200, by Ideenmodellierer
Bugfix: FutureTTS and Fahrenheit not displayed correct
Wed, 22 Aug 2018 11:35:05 +0200, by Ideenmodellierer
language updates
Wed, 15 Aug 2018 12:16:23 +0200, by heinrichsweikamp
language updates
Tue, 14 Aug 2018 13:53:43 +0200, by heinrichsweikamp
typo in info menu...
Tue, 14 Aug 2018 12:43:58 +0200, by heinrichsweikamp
Replaced wait loop with delay fct
Mon, 13 Aug 2018 19:11:14 +0200, by Ideenmodellierer
Bugfix font elements (ue missing)
Sun, 12 Aug 2018 23:02:13 +0200, by Ideenmodellierer
rename update batch file
Sat, 11 Aug 2018 13:57:47 +0200, by heinrichsweikamp
more language updates
Fri, 10 Aug 2018 19:40:55 +0200, by heinrichsweikamp
language updates
Fri, 10 Aug 2018 19:22:12 +0200, by heinrichsweikamp
Added UTF8 decode function
Thu, 09 Aug 2018 22:39:15 +0200, by Ideenmodellierer
Resolve format warnings
Thu, 09 Aug 2018 22:38:56 +0200, by Ideenmodellierer
language updates
Tue, 07 Aug 2018 17:03:36 +0200, by heinrichsweikamp
Italian activated (needs some fine tuning), special characters (?,?,?,?,? and others) currently not working...
Tue, 07 Aug 2018 00:24:05 +0200, by heinrichsweikamp
Added missing ENTRY point
Sun, 05 Aug 2018 12:57:49 +0200, by Ideenmodellierer
Allow RTE binaries > 64k size
Sun, 05 Aug 2018 12:57:23 +0200, by Ideenmodellierer
Added reference projects
Sun, 05 Aug 2018 12:56:43 +0200, by Ideenmodellierer
Resolved warnings pointing to possible invalid memory access
Tue, 31 Jul 2018 22:28:21 +0200, by Ideenmodellierer
remove hgsub files
Mon, 30 Jul 2018 11:37:39 +0200, by heinrichsweikamp
add o4pack files
Mon, 30 Jul 2018 11:31:20 +0200, by heinrichsweikamp
Increased version number
Sun, 29 Jul 2018 18:27:37 +0200, by Ideenmodellierer
Added instruction to optimize for size
Sun, 29 Jul 2018 18:16:01 +0200, by Ideenmodellierer
Always include Fonts library (to have the adresses defined)
Sun, 29 Jul 2018 18:09:58 +0200, by Ideenmodellierer
Replaced generic with individual sections to invert the link order and to be able to place specific fonts at defined locations
Sun, 29 Jul 2018 18:07:52 +0200, by Ideenmodellierer
Placed directory sections in firmware memory space
Sun, 29 Jul 2018 18:06:37 +0200, by Ideenmodellierer
Split memory areas and reverse engineered font library
Sun, 29 Jul 2018 18:05:44 +0200, by Ideenmodellierer
Force reset in case of a hard fault
Sun, 29 Jul 2018 16:46:31 +0200, by Ideenmodellierer
Non functional change just to use same symbols as CPU1
Sun, 29 Jul 2018 16:45:37 +0200, by Ideenmodellierer
Aligned structure with CPU1 linker file
Sun, 29 Jul 2018 16:45:00 +0200, by Ideenmodellierer
Increase version number
Sun, 29 Jul 2018 16:17:25 +0200, by Ideenmodellierer
include in ostc4 repository
Sat, 28 Apr 2018 11:52:34 +0200, by heinrichsweikamp
init
Sat, 28 Apr 2018 11:48:39 +0200, by heinrichsweikamp
Update author name for release
Sat, 28 Apr 2018 11:33:57 +0200, by heinrichsweikamp
... more GPL License and general cleanups
Wed, 07 Mar 2018 18:56:48 +0100, by jDG
... OpenOCD scripts to dump firmwares (not working)
Wed, 07 Mar 2018 17:35:35 +0100, by jDG
... minor warnings
Tue, 27 Feb 2018 13:57:30 +0100, by jDG
change author name to heinrichs weikamp gmbh
Sat, 10 Feb 2018 11:25:13 +0100, by heinrichsweikamp
[ADD]Discovery/Src licences, plus reindentation
Tue, 06 Feb 2018 16:13:30 +0100, by jDG
ADD GPL License ...
Tue, 23 Jan 2018 17:29:40 +0100, by jDG
ADD script to set GPL headers
Tue, 23 Jan 2018 13:36:25 +0100, by jDG
... Fighting with internal oscillator.
Wed, 10 Jan 2018 19:59:50 +0100, by JeanDo
ADD C indentation standard
Wed, 10 Jan 2018 11:22:33 +0100, by JeanDo
... single step in Discovery code: trying to have an oscillator.
Tue, 09 Jan 2018 18:34:03 +0100, by jDG
FIX move bootloader SFirmwareData at fixed address 0x0800A000
Wed, 03 Jan 2018 01:40:59 +0100, by jdg
ADD font check code that runs at FontPack installation.
Mon, 01 Jan 2018 20:12:34 +0100, by JeanDo
ADD missing chars in FontPack
Mon, 01 Jan 2018 18:56:14 +0100, by JeanDo
FIX need to link actual FirmwareData too...
Mon, 01 Jan 2018 18:55:12 +0100, by JeanDo
FIX shared SFirmwareData signature at fixed address
Mon, 01 Jan 2018 18:24:07 +0100, by JeanDo
NEW shared font directory at 0x081E0000
Sat, 30 Dec 2017 20:24:04 +0100, by jdg
... more docs
Tue, 26 Dec 2017 19:31:13 +0100, by jdg
... typo in subrepo ?
Tue, 26 Dec 2017 18:26:12 +0100, by jdg
ADD wiki sub-repos
Tue, 26 Dec 2017 18:24:03 +0100, by jdg
... FontPack CPU1 project
Tue, 26 Dec 2017 18:22:49 +0100, by jdg
FIRST CPU2-RTE LINKING VERSION
Tue, 19 Dec 2017 23:42:13 +0100, by JeanDo
FIX move fonts to UPPER ROM SECTION (above 0x8100000)
Tue, 19 Dec 2017 18:47:04 +0100, by JeanDo
ADD CPU1 pin layout
Tue, 19 Dec 2017 18:45:03 +0100, by JeanDo
FIRST CPU1-DISCOVERY LINKING VERSION
Tue, 19 Dec 2017 13:45:03 +0100, by jDG
CLEANUP move driver code to Common/Drivers
Tue, 19 Dec 2017 11:19:35 +0100, by jDG
FIX text_multilanguage shall be compiled once
Mon, 18 Dec 2017 18:16:28 +0100, by JeanDo
FIX recover jeopardized fonts & images structure
Mon, 18 Dec 2017 17:08:23 +0100, by JeanDo
... move absolute data to named sections
Mon, 18 Dec 2017 14:30:14 +0100, by jDG
CLEAN retrieve original startup code. reset linker script.
Mon, 18 Dec 2017 14:03:55 +0100, by jDG
... more clean
Fri, 15 Dec 2017 02:06:18 +0100, by JeanDo
MOVE files for other applications
Fri, 15 Dec 2017 01:45:20 +0100, by JeanDo
... debugging Discovery project compilation.
Wed, 13 Dec 2017 18:23:00 +0100, by jDG
CLEANUP remove duplicated support sources
Wed, 13 Dec 2017 13:30:13 +0100, by jDG

less more | rev 482: (0) -480 tip

Mercurial > public > ostc4

graph