ostc4: revision graph

graph

less more | rev 778: (0) -300 -100 -56 +56 +100 tip

Zusammenf?hren
Mon, 22 May 2023 09:15:09 +0200, by heinrichsweikamp
This is only showing if one of the compass views is visible. It should make it possible to verify that a correct heading is set as the user can see the compass readout when pushing the button. (mikeller)
Mon, 22 May 2023 09:14:27 +0200, by heinrichsweikamp
Add support for a configurable compass declination in a range of -99 to 99 degrees.
Thu, 18 May 2023 09:49:17 +0200, by heinrichsweikamp
Add a shortcuts to change the setpoint to the loop to the 'normal' display when diving. It is only shown when diving in CCR mode and on the loop.
Thu, 11 May 2023 12:13:03 +0200, by heinrichsweikamp
more menu items for the compass menu: Delete bearing, and reset to land based bearing. I have also re-enabled the real time bearing display in the menu - makes it easier to set the correct bearing. (mikeller)
Wed, 10 May 2023 16:25:39 +0200, by heinrichsweikamp
Menu shortcut for bailout / return to circuit when diving in CCR mode (mikeller)
Wed, 10 May 2023 16:24:57 +0200, by heinrichsweikamp
Fix character truncation when screen is flipped. This was causing the dive computer to lock up when in English Units with the screen flipped when the first decompression stop is shown using FONT_105.
Sat, 22 Apr 2023 21:11:50 -0500, by izzni
Revised automatic setpoint change. The proposed approach is essentially the approach used by most controllers of eCCR ('upshift' on descent, 'downshift' on ascent), so that the OSTC4 when used as a backup computer for eCCR will make the changes at the same time as the eCCR itself.
Fri, 21 Apr 2023 09:48:23 +0200, by heinrichsweikamp
CCR overview in surface mode. Makes it easy to quickly check that all settings (mode, setpoints, diluent, scrubber timer) are correct when preparing to dive (also makes the OC gas list available in surface mode for the same reason).
Fri, 21 Apr 2023 09:47:44 +0200, by heinrichsweikamp
Deactivation of the 'fallback' option when the CCR mode is set to 'Fixed' - this makes it a little clearer that the option has no influence in this mode.
Fri, 21 Apr 2023 09:47:06 +0200, by heinrichsweikamp
1.6.2 release
Thu, 13 Apr 2023 09:35:43 +0200, by heinrichsweikamp
Update build for testing
Wed, 12 Apr 2023 09:56:00 +0200, by heinrichsweikamp
change button default responsiveness to 100
Wed, 12 Apr 2023 09:30:15 +0200, by heinrichsweikamp
After a firmware update, use the factory settings for button sensitivity if these exist, the default settings otherwise.
Wed, 12 Apr 2023 09:24:44 +0200, by heinrichsweikamp
Update build for testing
Mon, 27 Mar 2023 10:04:53 +0200, by heinrichsweikamp
increase HAL_Delay to 10ms for cold-start-button reset
Sun, 26 Mar 2023 18:34:30 +0200, by heinrichsweikamp
Preparing a 1.6.2 release candidate
Sun, 26 Mar 2023 11:27:29 +0200, by heinrichsweikamp
Fix/handle negative scrubber timer values
Tue, 21 Mar 2023 12:57:37 +0100, by heinrichsweikamp
Quit simualted dives after the dive time set in the SIM tab.
Tue, 21 Mar 2023 12:56:54 +0100, by heinrichsweikamp
Some compass improvements from mikeller
Fri, 17 Mar 2023 09:35:25 +0100, by heinrichsweikamp
- Colours for scrubber display when time remaining falls below a threshold value
Wed, 15 Mar 2023 09:18:07 +0100, by heinrichsweikamp
Dev Bugfix: ignore analog out of bounds limits for DiveO2 sensor:
Tue, 07 Mar 2023 22:14:20 +0100, by Ideenmodellierer
Added visualization of CO2 during dive:
Tue, 07 Mar 2023 20:02:05 +0100, by Ideenmodellierer
Cleanup display of multiple warnings in T3 (Big font) view:
Tue, 07 Mar 2023 19:59:02 +0100, by Ideenmodellierer
Only show autodetection in sensor menu if external interface is present:
Tue, 07 Mar 2023 19:55:13 +0100, by Ideenmodellierer
Updated outdated comment
Tue, 07 Mar 2023 19:52:18 +0100, by Ideenmodellierer
Dev Bugfix: Alignment problem in lifedata structure:
Tue, 07 Mar 2023 19:51:30 +0100, by Ideenmodellierer
resolv merge
Mon, 13 Mar 2023 22:23:00 +0100, by Ideenmodellierer
Avoid blinking in customer view selection page:
Sun, 05 Mar 2023 22:17:32 +0100, by Ideenmodellierer
Added enum for Co2 display
Mon, 13 Mar 2023 22:18:28 +0100, by Ideenmodellierer
Added display of co2 ppm values:
Sun, 05 Mar 2023 22:14:53 +0100, by Ideenmodellierer
Added pressure compensation to CO2 detection:
Sun, 05 Mar 2023 22:06:47 +0100, by Ideenmodellierer
Code cleanup sensors under development:
Tue, 21 Feb 2023 21:19:31 +0100, by Ideenmodellierer
Update Sentinel protocol:
Sun, 19 Feb 2023 21:52:02 +0100, by Ideenmodellierer
Added DiveO2 fatal error detection:
Sun, 19 Feb 2023 21:51:19 +0100, by Ideenmodellierer
Enable start dive in Big font display:
Sun, 19 Feb 2023 21:48:47 +0100, by Ideenmodellierer
Update Sentinel protocol:
Sun, 19 Feb 2023 21:43:24 +0100, by Ideenmodellierer
Added button lock after wakeup in surface mode:
Thu, 02 Feb 2023 17:35:54 +0100, by Ideenmodellierer
Added button lock after wakeup in surface mode:
Thu, 02 Feb 2023 17:35:38 +0100, by Ideenmodellierer
Enable start dive in Big font display:
Thu, 02 Feb 2023 17:26:54 +0100, by Ideenmodellierer
Added data init function for external interface:
Thu, 02 Feb 2023 17:19:24 +0100, by Ideenmodellierer
NEW: Add mini compass with marker declination indication
Mon, 06 Mar 2023 16:03:00 +0100, by heinrichsweikamp
Fixed logbook download after switch from CCR to extra (OC) gas if the extra gas
Fri, 03 Mar 2023 10:41:44 +0100, by heinrichsweikamp
Fixed invalid setpoint (0.0) used after switch from CCR to extra (OC) gas
Tue, 14 Feb 2023 10:21:56 +0100, by heinrichsweikamp
Removed interface selection from sensor menu:
Sun, 15 Jan 2023 21:51:54 +0100, by Ideenmodellierer
Optical sensor as default:
Sun, 15 Jan 2023 21:48:34 +0100, by Ideenmodellierer
Fix compiler switch:
Sun, 15 Jan 2023 21:45:14 +0100, by Ideenmodellierer
Improvment sensor Autodetection:
Sun, 15 Jan 2023 21:43:33 +0100, by Ideenmodellierer
Update sensor menu support for automatic sensor detection:
Sat, 14 Jan 2023 20:49:40 +0100, by Ideenmodellierer
Added auto detection functionality for sensors connected to the external interface:
Sat, 14 Jan 2023 20:46:17 +0100, by Ideenmodellierer
Added sensor map to Firmware <=> RTE inferface:
Sat, 14 Jan 2023 20:41:36 +0100, by Ideenmodellierer
Enabled CO2 support for beta test phase:
Sat, 14 Jan 2023 20:37:20 +0100, by Ideenmodellierer
Bugfix data synchronization after RTE start:
Sat, 14 Jan 2023 20:35:40 +0100, by Ideenmodellierer
Update CO2 sensor implementation:
Sat, 07 Jan 2023 18:11:52 +0100, by Ideenmodellierer
Development feature: external pressure sensor
Thu, 05 Jan 2023 18:30:06 +0100, by Ideenmodellierer
DigO2 added raw data request:
Thu, 05 Jan 2023 18:27:04 +0100, by Ideenmodellierer

less more | rev 778: (0) -300 -100 -56 +56 +100 tip