ostc4: revision graph

graph

less more | rev 727: (0) -448 tip

Enabled CO2 support for beta test phase:
Sat, 14 Jan 2023 20:37:20 +0100, by Ideenmodellierer
Bugfix data synchronization after RTE start:
Sat, 14 Jan 2023 20:35:40 +0100, by Ideenmodellierer
Update CO2 sensor implementation:
Sat, 07 Jan 2023 18:11:52 +0100, by Ideenmodellierer
Development feature: external pressure sensor
Thu, 05 Jan 2023 18:30:06 +0100, by Ideenmodellierer
DigO2 added raw data request:
Thu, 05 Jan 2023 18:27:04 +0100, by Ideenmodellierer
Show saturation in large font (T3) view:
Thu, 05 Jan 2023 18:25:47 +0100, by Ideenmodellierer
DigO2 added raw data request:
Thu, 05 Jan 2023 18:22:21 +0100, by Ideenmodellierer
Bugfix set date (year):
Tue, 03 Jan 2023 19:47:12 +0100, by Ideenmodellierer
Add build for 1.6.1 beta / RTE 2.9 (Support for DiveO2 solid state oxygen sensors)
Sun, 27 Nov 2022 15:18:00 +0100, by heinrichsweikamp
Updated menu structure to support new sensor information page:
Sun, 20 Nov 2022 20:49:41 +0100, by Ideenmodellierer
Added new info page for extended sensor data:
Sun, 20 Nov 2022 20:46:10 +0100, by Ideenmodellierer
Added customizable data area for specific sensor data:
Sun, 20 Nov 2022 20:43:04 +0100, by Ideenmodellierer
Increased version number and set beta label
Sun, 20 Nov 2022 20:42:33 +0100, by Ideenmodellierer
Added customizable data area for specific sensor data:
Sun, 20 Nov 2022 20:42:08 +0100, by Ideenmodellierer
Increased version number and set beta label
Sun, 20 Nov 2022 20:37:44 +0100, by Ideenmodellierer
Bugfix PSCR menu button label:
Sun, 20 Nov 2022 20:36:34 +0100, by Ideenmodellierer
Development bugfix number of spare bytes in setting structure
Tue, 08 Nov 2022 22:16:56 +0100, by Ideenmodellierer
Extension scrubber time:
Tue, 08 Nov 2022 21:16:17 +0100, by Ideenmodellierer
Bugfix compass bearing:
Tue, 08 Nov 2022 21:13:14 +0100, by Ideenmodellierer
Menu cleanup rebreather specific settings:
Thu, 03 Nov 2022 20:44:51 +0100, by Ideenmodellierer
Menu cleanup rebreather specific settings:
Thu, 03 Nov 2022 20:44:21 +0100, by Ideenmodellierer
Bugfix: only reset menu if a new sub menu is created:
Thu, 03 Nov 2022 20:37:06 +0100, by Ideenmodellierer
Bugfix release frame:
Tue, 01 Nov 2022 09:55:45 +0100, by Ideenmodellierer
Added protocol functions for UART DiveO2 sensor:
Fri, 28 Oct 2022 20:49:21 +0200, by Ideenmodellierer
Added selection of digital o2 sensor source to HW menu:
Fri, 28 Oct 2022 20:32:24 +0200, by Ideenmodellierer
Added digital o2 sensor to settings and data exchange:
Fri, 28 Oct 2022 20:29:37 +0200, by Ideenmodellierer
Bugfix display of deactivated sensors:
Fri, 28 Oct 2022 19:39:20 +0200, by Ideenmodellierer
Bugfix motioncontrol frame deactivation:
Tue, 18 Oct 2022 21:21:32 +0200, by Ideenmodellierer
Cleanup warnings:
Tue, 18 Oct 2022 20:56:19 +0200, by Ideenmodellierer
Bugfix Empty menu:
Sun, 25 Sep 2022 21:13:45 +0200, by Ideenmodellierer
Improvment key event detection:
Sun, 25 Sep 2022 21:09:18 +0200, by Ideenmodellierer
Merge
Fri, 19 Aug 2022 11:30:24 +0200, by heinrichsweikamp
1.6.0 release Betatest
Fri, 19 Aug 2022 11:27:44 +0200, by heinrichsweikamp
Update current build for testing Betatest
Sat, 06 Aug 2022 11:10:56 +0200, by heinrichsweikamp
Improvment charge percent visualization: Betatest
Fri, 05 Aug 2022 16:04:52 +0200, by Ideenmodellierer
Added compile switch for Sentinel rebreather option Betatest
Fri, 05 Aug 2022 15:27:01 +0200, by Ideenmodellierer
Improvment external interface usage: Betatest
Fri, 05 Aug 2022 15:26:28 +0200, by Ideenmodellierer
Added Sentinel protocoll support: Betatest
Fri, 05 Aug 2022 15:22:26 +0200, by Ideenmodellierer
Added Sentinel as O2 sensor source: Betatest
Fri, 05 Aug 2022 15:15:01 +0200, by Ideenmodellierer
Added sanity check for temperature and pressure values: Betatest
Fri, 05 Aug 2022 15:13:29 +0200, by Ideenmodellierer
Increased version numbers: Betatest
Fri, 05 Aug 2022 15:10:10 +0200, by Ideenmodellierer
Bugfix Battery charge complete event: Betatest
Fri, 05 Aug 2022 14:56:17 +0200, by Ideenmodellierer
Bugfix automatic switch to o2 sensor custom view: Betatest
Wed, 03 Aug 2022 18:19:03 +0200, by Ideenmodellierer
Ignore automatic setpoint changes during ascend: Betatest
Thu, 02 Jun 2022 20:24:59 +0200, by Ideenmodellierer
Bugfix: Set actual gas after basic dive settings were created: Betatest
Mon, 16 May 2022 20:50:26 +0200, by Ideenmodellierer
Bugfix low ppO2 warning in bailout mode: Betatest
Mon, 25 Apr 2022 21:15:01 +0200, by Ideenmodellierer
Bugfix screen clipping (Flipdisplay mode): Betatest
Mon, 25 Apr 2022 21:10:10 +0200, by Ideenmodellierer
Bugfix visualization better setpoint: Betatest
Mon, 25 Apr 2022 21:07:28 +0200, by Ideenmodellierer
cleanup: Use correct "per" symbol Betatest
Fri, 22 Apr 2022 18:24:43 +0200, by Jan Mulder
Bugfix: deco planner did not initialize properly Betatest
Thu, 21 Apr 2022 21:02:50 +0200, by Jan Mulder
Move include file to common to ... Betatest
Wed, 20 Apr 2022 20:25:04 +0200, by Jan Mulder
Allow longer scrubber time Betatest
Mon, 22 Nov 2021 19:39:11 +0100, by Jan Mulder
Bugfix: Missing flip screen support for charge view Betatest
Wed, 30 Mar 2022 18:07:21 +0200, by Ideenmodellierer
Zusammenf?hren Betatest
Wed, 30 Mar 2022 18:01:29 +0200, by heinrichsweikamp
Show 98% in case of Oxygen as the calibrating gas Betatest
Wed, 30 Mar 2022 18:00:21 +0200, by heinrichsweikamp
Added Charging view: Betatest
Sat, 12 Mar 2022 23:01:11 +0100, by Ideenmodellierer
Support of unknown charging counter values: Betatest
Sat, 12 Mar 2022 22:58:22 +0100, by Ideenmodellierer
Reduce display brightness in case the charger is connected: Betatest
Sat, 12 Mar 2022 22:54:26 +0100, by Ideenmodellierer
Rework charge cycle: Betatest
Sat, 12 Mar 2022 22:49:09 +0100, by Ideenmodellierer
Rework charge cycle: Betatest
Sat, 12 Mar 2022 22:48:45 +0100, by Ideenmodellierer
Increased version number Betatest
Sat, 12 Mar 2022 22:42:56 +0100, by Ideenmodellierer
increase version numbers for upcomming release Betatest
Sat, 12 Mar 2022 14:57:54 +0100, by heinrichsweikamp
update test build Betatest
Fri, 24 Dec 2021 13:40:47 +0100, by heinrichsweikamp
Stability improvment bluetooth startup: Betatest
Tue, 21 Dec 2021 19:36:41 +0100, by Ideenmodellierer
Revert Setbluetooh name changes Betatest
Tue, 21 Dec 2021 19:32:29 +0100, by Ideenmodellierer
PSCR Mode Betatest
Tue, 14 Dec 2021 15:36:10 +0100, by heinrichs weikamp
Undo Rev. 660
Mon, 01 Nov 2021 12:39:34 +0100, by heinrichs weikamp
Add option to reset bluetooth name
Sun, 08 Aug 2021 09:36:23 +0200, by heinrichsweikamp
Update build file for testing
Wed, 28 Apr 2021 09:47:25 +0200, by heinrichs weikamp
Bugfix handling of new menu tab in flipped mode:
Tue, 27 Apr 2021 21:29:26 +0200, by Ideenmodellierer
Update release date
Mon, 26 Apr 2021 15:03:04 +0200, by heinrichs weikamp
Added visualization of scrubber time:
Sun, 25 Apr 2021 20:47:01 +0200, by Ideenmodellierer
Added count down timer for scrubber time:
Sun, 25 Apr 2021 20:42:56 +0200, by Ideenmodellierer
Introduced new menu tab for addition CCR options:
Sun, 25 Apr 2021 20:41:19 +0200, by Ideenmodellierer
Bugfix temperature display Logpage2:
Sun, 25 Apr 2021 20:36:18 +0200, by Ideenmodellierer
Allow setpoint starting at 0.4 ppO2:
Mon, 19 Apr 2021 20:34:53 +0200, by Ideenmodellierer
Automatik setpoint change:
Mon, 19 Apr 2021 20:20:38 +0200, by Ideenmodellierer
Automatik setpoint change:
Mon, 19 Apr 2021 20:19:32 +0200, by Ideenmodellierer
Bugfix consider checkbox in calculation of right aligned and centered position:
Mon, 19 Apr 2021 20:16:24 +0200, by Ideenmodellierer
Motion detection: Enable focus after focus calibration:
Mon, 19 Apr 2021 20:14:20 +0200, by Ideenmodellierer
Integrated selection of bailout in the diluent selection page:
Tue, 13 Apr 2021 19:25:41 +0200, by Ideenmodellierer
Remove battery charge counter from information menu:
Tue, 13 Apr 2021 19:21:14 +0200, by Ideenmodellierer
Small changes in charger state handling:
Tue, 13 Apr 2021 19:18:32 +0200, by Ideenmodellierer
Compile with ENABLE_CHARGER_STATUS_V2
Tue, 30 Mar 2021 10:34:12 +0200, by heinrichs weikamp
Reimplemented charger status generation (deactivated):
Wed, 24 Mar 2021 22:06:00 +0100, by Ideenmodellierer
Do not show focus indicator in case motion detection is suspended:
Wed, 24 Mar 2021 21:28:41 +0100, by Ideenmodellierer
Development Bugfix Deco bars not shown after last deco stop passed:
Thu, 11 Mar 2021 21:45:22 +0100, by Ideenmodellierer
Development bugfix Viewport settings:
Thu, 11 Mar 2021 21:43:43 +0100, by Ideenmodellierer
add build for testing, advance to FW1.5.7, RTE is unchanged since 1.5.6
Thu, 25 Feb 2021 12:20:43 +0100, by heinrichsweikamp
Added last measured PPO2 value to sensor selection dialog:
Wed, 24 Feb 2021 21:45:35 +0100, by Ideenmodellierer
Debounce fallback warning:
Wed, 24 Feb 2021 21:04:07 +0100, by Ideenmodellierer
Debounce fallback warning:
Wed, 24 Feb 2021 21:03:54 +0100, by Ideenmodellierer
Debounce fallback warning:
Wed, 24 Feb 2021 21:03:22 +0100, by Ideenmodellierer
Enable sensor check for Analog PPO2 mode:
Wed, 24 Feb 2021 19:18:26 +0100, by Ideenmodellierer
Added menu structure to allow ppo2 modification in simulator mode:
Tue, 23 Feb 2021 21:58:18 +0100, by Ideenmodellierer
Warnings:
Tue, 23 Feb 2021 21:55:52 +0100, by Ideenmodellierer
Warnings:
Tue, 23 Feb 2021 21:55:26 +0100, by Ideenmodellierer
Warnings:
Tue, 23 Feb 2021 21:54:56 +0100, by Ideenmodellierer
Added functionality to add ppo2 mV offset:
Tue, 23 Feb 2021 21:53:24 +0100, by Ideenmodellierer
Added compile switch for T3_PROFILE menu operation option
Fri, 12 Feb 2021 21:46:36 +0100, by Ideenmodellierer
Improve in / out of focus transitions:
Fri, 12 Feb 2021 21:43:27 +0100, by Ideenmodellierer
Added option to select sensitivity of focus detection:
Fri, 12 Feb 2021 21:37:50 +0100, by Ideenmodellierer
Switch Sector / Scroll detection to vector implementation:
Mon, 08 Feb 2021 21:35:46 +0100, by Ideenmodellierer
Development bugfix: Marker in standard t3 view drawn in wrong direction
Sun, 07 Feb 2021 22:05:32 +0100, by Ideenmodellierer
Improvment frame Handling:
Sun, 07 Feb 2021 22:04:43 +0100, by Ideenmodellierer
Adjustments for flipped display view:
Wed, 03 Feb 2021 21:45:48 +0100, by Ideenmodellierer
Use roll and pitch agles in 0-360 format:
Wed, 03 Feb 2021 21:44:22 +0100, by Ideenmodellierer
Added minilog functions to allow marker synchronisation:
Wed, 27 Jan 2021 22:12:44 +0100, by Ideenmodellierer
Added t3 quick menu for marker synchronisation:
Wed, 27 Jan 2021 22:10:11 +0100, by Ideenmodellierer
Development bugfix: focus state not remembered:
Wed, 27 Jan 2021 22:04:45 +0100, by Ideenmodellierer
Development bugfix: Low battery warning was interpretated as marker:
Wed, 27 Jan 2021 22:03:11 +0100, by Ideenmodellierer
Development bugfix: show replay symbol only for the selected dive:
Wed, 27 Jan 2021 21:58:46 +0100, by Ideenmodellierer
Moved non critical functions from timer interrupt to main loop:
Wed, 27 Jan 2021 21:56:48 +0100, by Ideenmodellierer
Added "Set Marker" to T3 quick menu:
Wed, 20 Jan 2021 20:05:05 +0100, by Ideenmodellierer
Added "Set Marker" to T3 quick menu:
Fri, 15 Jan 2021 21:33:07 +0100, by Ideenmodellierer
Bugfix inverted whitspace:
Fri, 15 Jan 2021 21:20:29 +0100, by Ideenmodellierer
Suspend MotionDetection events while diver is operationg the OSTC:
Thu, 14 Jan 2021 21:25:15 +0100, by Ideenmodellierer
Added access to logbook marker data:
Thu, 14 Jan 2021 20:38:28 +0100, by Ideenmodellierer
Bugfix: CalibViewport were shown even in case the compile switch had not been set:
Thu, 14 Jan 2021 19:17:28 +0100, by Ideenmodellierer
Update RTE required value for release
Fri, 05 Feb 2021 14:53:50 +0100, by heinrichsweikamp
Added tag v1.5.6 release for changeset 06ec1da5e105
Fri, 05 Feb 2021 14:50:18 +0100, by heinrichsweikamp
1.5.6 release v1.5.6 release
Fri, 05 Feb 2021 14:50:05 +0100, by heinrichsweikamp
change O2_CALIB_FRACTION_O2 to 0.98
Thu, 07 Jan 2021 09:53:04 +0100, by heinrichsweikamp
Merged menu items of viewport and motion control:
Wed, 06 Jan 2021 21:01:00 +0100, by Ideenmodellierer
T3 profile view: Added visualization of deco data
Wed, 06 Jan 2021 19:41:43 +0100, by Ideenmodellierer
Added replay data scaling in case life data is longer than replay block
Tue, 05 Jan 2021 20:35:01 +0100, by Ideenmodellierer
Bugfix T3 skip deactivated views:
Mon, 04 Jan 2021 22:49:07 +0100, by Ideenmodellierer
Added compile switch for new T3 View Profile
Mon, 04 Jan 2021 22:45:37 +0100, by Ideenmodellierer
Bugfix T3 skip deactivated views:
Mon, 04 Jan 2021 21:48:31 +0100, by Ideenmodellierer
New replay block for T3 profile:
Mon, 04 Jan 2021 21:41:51 +0100, by Ideenmodellierer
MotionControl-Sector: Map sectors during switch T7 <=> T3:
Mon, 04 Jan 2021 21:38:28 +0100, by Ideenmodellierer
Added functionality to select a dive to be shown in the T3 profile view:
Mon, 04 Jan 2021 21:35:38 +0100, by Ideenmodellierer
Bugfix Selection of primary view:
Mon, 04 Jan 2021 21:32:39 +0100, by Ideenmodellierer
Added compile switch for new T3 View Profile
Mon, 04 Jan 2021 21:30:04 +0100, by Ideenmodellierer
Added PrintGraph option to skip invalid data entries:
Mon, 04 Jan 2021 21:24:24 +0100, by Ideenmodellierer
MotionCtrl - Sectorview Map sectors directly to custom views:
Sun, 03 Jan 2021 14:43:16 +0100, by Ideenmodellierer
Minor: Comment translation into English
Wed, 06 Jan 2021 22:02:49 +0100, by heinrichsweikamp
Align VPM tag in log list to be at same position as GF tag:
Tue, 22 Dec 2020 22:23:11 +0100, by Ideenmodellierer
Minor: Update the documentation for building the code
Thu, 17 Dec 2020 10:58:28 +0100, by heinrichsweikamp
Update current build, "RTErequired" value and release date
Thu, 17 Dec 2020 09:52:12 +0100, by heinrichsweikamp
update ostc4pack sample files
Wed, 16 Dec 2020 09:43:11 +0100, by heinrichsweikamp
Motion control: Jump back to primary view if focus is lost:
Sun, 13 Dec 2020 18:31:40 +0100, by Ideenmodellierer
Reduced view angle and number of vusiualized custom views in setor mode:
Sun, 13 Dec 2020 18:29:12 +0100, by Ideenmodellierer
Added option for 100% o2 calibration:
Sat, 12 Dec 2020 21:05:11 +0100, by Ideenmodellierer
Solved minor warnings
Sat, 12 Dec 2020 20:54:31 +0100, by Ideenmodellierer
Show Fallback if no valid sensor value is available:
Sat, 12 Dec 2020 20:52:58 +0100, by Ideenmodellierer
Added ex Interface measurement restart in case of i2c disturbance:
Sat, 12 Dec 2020 19:18:57 +0100, by Ideenmodellierer
Bugfix bad resolution of compass LSM303AGR:
Sat, 12 Dec 2020 19:16:37 +0100, by Ideenmodellierer
Minor: Functional inert cleanup of some unused variables
Thu, 03 Dec 2020 13:17:32 +0100, by heinrichsweikamp
Rework pitch detection:
Sun, 29 Nov 2020 23:02:11 +0100, by Ideenmodellierer
Handle o2 voltage values < 0.5mV as invalid:
Sun, 29 Nov 2020 22:58:11 +0100, by Ideenmodellierer
Return to o2 values:
Sun, 29 Nov 2020 22:55:31 +0100, by Ideenmodellierer
Change style of viewport calibration menu:
Sun, 29 Nov 2020 22:53:33 +0100, by Ideenmodellierer
Improved focus detection:
Wed, 25 Nov 2020 20:26:01 +0100, by Ideenmodellierer
Update String "Blickwinkel":
Wed, 25 Nov 2020 20:19:50 +0100, by Ideenmodellierer
Added debug view to viewport calibration:
Wed, 25 Nov 2020 20:18:22 +0100, by Ideenmodellierer
Reactivate compass parameter stored in NVM:
Wed, 25 Nov 2020 20:16:20 +0100, by Ideenmodellierer
Try to reduce legth of log entry string:
Mon, 30 Nov 2020 20:55:23 +0100, by Ideenmodellierer
Added new section "lower.font":
Mon, 30 Nov 2020 20:52:49 +0100, by Ideenmodellierer
Minor: Update the documentation for building the code
Sun, 29 Nov 2020 11:41:03 +0100, by heinrichsweikamp
-Add 12HR Time Support
Tue, 24 Nov 2020 13:22:23 -0600, by izzni
add current build
Sat, 21 Nov 2020 17:41:59 +0100, by heinrichsweikamp
Bugfix center / right alignment if dualfont is used:
Sun, 15 Nov 2020 20:12:19 +0100, by Ideenmodellierer
Bugfix One or more deactivated sensors hide sensor display:
Sun, 15 Nov 2020 20:09:31 +0100, by Ideenmodellierer
Refine o2 sensor diagnostic functions:
Sun, 15 Nov 2020 20:01:56 +0100, by Ideenmodellierer
Added ADC sensor interface to O2 sensore menu structure:
Sun, 15 Nov 2020 19:58:14 +0100, by Ideenmodellierer
Solved minor warnings
Sun, 15 Nov 2020 19:54:36 +0100, by Ideenmodellierer
Added O2 sensor source and calibration parameters to setting structure
Sun, 15 Nov 2020 19:53:09 +0100, by Ideenmodellierer
Check if HW evaluation was performed:
Sun, 15 Nov 2020 19:52:03 +0100, by Ideenmodellierer
Changed operation mode of RecoverSampleIndex:
Thu, 12 Nov 2020 20:06:04 +0100, by Ideenmodellierer
Stabilityfix: Do not trust lastDiveLogID == 0 at startup:
Thu, 12 Nov 2020 20:03:00 +0100, by Ideenmodellierer
Switch source of o2 sensor data depending on availability of external ADC:
Thu, 12 Nov 2020 19:54:58 +0100, by Ideenmodellierer
Added HW_Info to Discovery <=> RTE data exchange:
Thu, 12 Nov 2020 19:48:28 +0100, by Ideenmodellierer
Added external ADC interface functionality (MCP3424):
Thu, 12 Nov 2020 19:46:03 +0100, by Ideenmodellierer
Added color indicator for focus state:
Sun, 08 Nov 2020 18:49:54 +0100, by Ideenmodellierer
Added menu structure to acces viewport calibration:
Sun, 08 Nov 2020 18:46:46 +0100, by Ideenmodellierer
Added viewport functionality:
Sun, 08 Nov 2020 18:43:19 +0100, by Ideenmodellierer
Make sure motion detection settings are set to default values:
Sun, 08 Nov 2020 18:38:53 +0100, by Ideenmodellierer
Only execute motion detection functions if features is enabled:
Sun, 08 Nov 2020 18:36:02 +0100, by Ideenmodellierer
Update roll and pitch value in simulation mode:
Sun, 08 Nov 2020 16:38:43 +0100, by Ideenmodellierer
Added viewport calibration to dive menu:
Mon, 02 Nov 2020 21:17:45 +0100, by Ideenmodellierer
Added new settings for Viewport:
Mon, 02 Nov 2020 21:15:42 +0100, by Ideenmodellierer
Add I2C address for external bulkhead ADC (Hardware gen 3 only) to i2c.h
Tue, 03 Nov 2020 12:47:51 +0100, by heinrichsweikamp
add current build
Mon, 02 Nov 2020 12:13:02 +0100, by heinrichsweikamp
Shortend t3 view names:
Sun, 11 Oct 2020 18:33:19 +0200, by Ideenmodellierer
Added new t3 view showing first deco stop and tts in parallel:
Sat, 10 Oct 2020 21:02:05 +0200, by Ideenmodellierer
Added default view selection and auto return to view to t3 visualization:
Sat, 10 Oct 2020 18:34:10 +0200, by Ideenmodellierer
Bugfix return from submenu in t3 view:
Sat, 10 Oct 2020 18:30:13 +0200, by Ideenmodellierer
Added inertia simulation for compass heading:
Sat, 10 Oct 2020 16:59:18 +0200, by Ideenmodellierer
BugFix firmware downgrade to version with less settings:
Sat, 10 Oct 2020 13:51:44 +0200, by Ideenmodellierer
Added center / right alignment option to custom text display:
Wed, 07 Oct 2020 18:07:10 +0200, by Ideenmodellierer
Changed visualization of Depth / temperatur / debugview entry
Wed, 07 Oct 2020 17:15:27 +0200, by Ideenmodellierer
Increased max value for surface pressure:
Wed, 07 Oct 2020 17:12:44 +0200, by Ideenmodellierer
Added tag 1.5.5 release for changeset 02e7e11fdbe8
Sun, 04 Oct 2020 15:50:43 +0200, by heinrichsweikamp
increase version numbers, compile with TRUST_LOG_CONSISTENCY switch 1.5.5 release
Fri, 25 Sep 2020 11:13:03 +0200, by heinrichsweikamp
add current build
Wed, 16 Sep 2020 10:52:57 +0200, by heinrichsweikamp
Bugfix custom view selection dialog:
Tue, 15 Sep 2020 20:57:04 +0200, by Ideenmodellierer
Bugfix: No need to consider surface custom view in count of enabled view:
Tue, 15 Sep 2020 20:54:54 +0200, by Ideenmodellierer
Added skip condition in custom view selection:
Tue, 15 Sep 2020 20:52:39 +0200, by Ideenmodellierer
Added new option to gas configuration: "Off":
Sun, 13 Sep 2020 20:59:38 +0200, by Ideenmodellierer
Do not show gases in "Off" state in custom gas list:
Sun, 13 Sep 2020 20:58:37 +0200, by Ideenmodellierer
Added new option to gas configuration: "Off":
Sun, 13 Sep 2020 20:55:54 +0200, by Ideenmodellierer
Change color ID used in strings for light grey:
Sun, 13 Sep 2020 20:49:58 +0200, by Ideenmodellierer
Minor: Removed duplicated definition of number of available gases
Sun, 13 Sep 2020 20:44:50 +0200, by Ideenmodellierer
Changed string for data view selections:
Thu, 10 Sep 2020 20:52:47 +0200, by Ideenmodellierer
Added compile switch for motion control:
Thu, 10 Sep 2020 20:51:36 +0200, by Ideenmodellierer
Move Bigfont and motion Ctrl selection menu out of custom view submenu:
Thu, 10 Sep 2020 20:47:48 +0200, by Ideenmodellierer
Moved custom view menu to new tab:
Tue, 08 Sep 2020 21:24:14 +0200, by Ideenmodellierer
Reset Safety Stop display in case of a new descend:
Sun, 06 Sep 2020 22:11:51 +0200, by Ideenmodellierer
Added T3_gaslist:
Sun, 06 Sep 2020 21:17:59 +0200, by Ideenmodellierer
Added color coding for cv gas list:
Sun, 06 Sep 2020 21:15:34 +0200, by Ideenmodellierer
Added quick menu function to big font view:
Sun, 06 Sep 2020 21:13:22 +0200, by Ideenmodellierer
Added missing display of button labels in refresh function:
Sun, 06 Sep 2020 21:09:37 +0200, by Ideenmodellierer
Properly send compass 3 into sleepmode (end-2019 hardware)
Wed, 16 Sep 2020 10:30:28 +0200, by heinrichsweikamp
Merge
Mon, 31 Aug 2020 20:06:59 +0200, by heinrichsweikamp
Added new strings for the selection of T3 custom views
Sun, 30 Aug 2020 17:31:29 +0200, by Ideenmodellierer
Minor adaptions in page layout:
Sun, 30 Aug 2020 17:30:54 +0200, by Ideenmodellierer
Display warning in t7 using centered strings
Sun, 30 Aug 2020 17:26:52 +0200, by Ideenmodellierer
Show page number in small letters if more than 8 tabs are active
Sun, 30 Aug 2020 17:26:00 +0200, by Ideenmodellierer
Reimplementation of tMenuEdit_select:
Sun, 30 Aug 2020 17:23:44 +0200, by Ideenmodellierer
Added new menu tab into call structure
Sun, 30 Aug 2020 17:20:16 +0200, by Ideenmodellierer
Added new top level menu for customization of views
Sun, 30 Aug 2020 17:19:23 +0200, by Ideenmodellierer
Removed second big font profile
Sun, 30 Aug 2020 17:14:31 +0200, by Ideenmodellierer
Added worst case plausibility check (disabled by compile switch)
Mon, 24 Aug 2020 19:59:28 +0200, by Ideenmodellierer
Bugfix display of disabled screen.
Mon, 24 Aug 2020 19:53:27 +0200, by Ideenmodellierer
Bugfix display of disabled screen.
Mon, 24 Aug 2020 19:43:13 +0200, by Ideenmodellierer
Bugfix right alignment of dualfont strings
Mon, 24 Aug 2020 19:39:28 +0200, by Ideenmodellierer
Added possibility to switch between "classic" bigfont views and a selection with a new information combination
Mon, 24 Aug 2020 19:36:18 +0200, by Ideenmodellierer
Added compile switch to enable / disable new BigFont layout
Mon, 24 Aug 2020 19:31:05 +0200, by Ideenmodellierer
Added dew parameter to enable selection of customer BigFont screens to be displayed
Mon, 24 Aug 2020 19:30:15 +0200, by Ideenmodellierer
Added worst case plausibility check (disabled by compile switch)
Mon, 24 Aug 2020 19:59:28 +0200, by Ideenmodellierer
Bugfix display of disabled screen.
Mon, 24 Aug 2020 19:53:27 +0200, by Ideenmodellierer
Bugfix display of disabled screen.
Mon, 24 Aug 2020 19:43:13 +0200, by Ideenmodellierer
Bugfix right alignment of dualfont strings
Mon, 24 Aug 2020 19:39:28 +0200, by Ideenmodellierer
Added possibility to switch between "classic" bigfont views and a selection with a new information combination
Mon, 24 Aug 2020 19:36:18 +0200, by Ideenmodellierer
Added compiler switch for existing debug view parameter
Thu, 20 Aug 2020 21:25:38 +0200, by Ideenmodellierer
Added tag v1.5.4 release for changeset e9ca66ce36e5
Mon, 10 Aug 2020 15:53:45 +0200, by heinrichsweikamp
1.5.4 release v1.5.4 release
Wed, 22 Jul 2020 11:55:53 +0200, by heinrichsweikamp
add wiki sub-directory
Mon, 29 Jun 2020 16:18:17 +0200, by heinrichsweikamp
Added "I2C_DeInit();" in hardware detection routines. It's the recommended way
Sat, 27 Jun 2020 18:40:32 +0200, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/FixLayout_Header_LogView (pull request #46)
Tue, 26 May 2020 19:27:07 +0000, by heinrichsweikamp
Bugfix header EEPROM layout: FixLayout_Header_LogView
Tue, 26 May 2020 21:13:12 +0200, by ideenmodellierer
Bugfix right alignment of string: FixLayout_Header_LogView
Tue, 26 May 2020 21:13:00 +0200, by ideenmodellierer
Small corrections layout Divelog page 1: FixLayout_Header_LogView
Tue, 26 May 2020 21:12:46 +0200, by ideenmodellierer
Development option only read bottledata: FixLayout_Header_LogView
Tue, 26 May 2020 21:12:02 +0200, by ideenmodellierer
Merged in Ideenmodellierer/ostc4/Improve_Button_Sleep (pull request #45)
Tue, 19 May 2020 07:27:18 +0000, by heinrichsweikamp
Bugfix calculation of string center position: Improve_Button_Sleep
Mon, 18 May 2020 21:51:08 +0200, by ideenmodellierer
Code cleanup pressure plausibility check: Improve_Button_Sleep
Wed, 13 May 2020 21:56:35 +0200, by ideenmodellierer
Bugfix unintended else condition: Improve_Button_Sleep
Wed, 13 May 2020 21:27:30 +0200, by ideenmodellierer
Development option only: Show Pressure update for a short time in the custom field (as warning) Improve_Button_Sleep
Tue, 12 May 2020 23:03:50 +0200, by ideenmodellierer
Only switch between "no fly" and "desaturation" in case there is desaturation time left: Improve_Button_Sleep
Tue, 12 May 2020 23:03:29 +0200, by ideenmodellierer
Balance value of button responsitivness were not considered during firmware startup: Improve_Button_Sleep
Tue, 12 May 2020 22:54:19 +0200, by ideenmodellierer
Changed default values: Improve_Button_Sleep
Tue, 12 May 2020 22:52:05 +0200, by ideenmodellierer
Added error detection for reading of ADC values in sleep mode: Improve_Button_Sleep
Tue, 12 May 2020 22:42:52 +0200, by ideenmodellierer
Do not signal power on reset in case of a "warm" reset: Improve_Button_Sleep
Tue, 12 May 2020 22:39:18 +0200, by ideenmodellierer
Merged in janlmulder/ostc4/fix-bat-2 (pull request #44)
Tue, 28 Apr 2020 15:37:47 +0000, by heinrichsweikamp
bugfix: implement battery charge percentage in dive header fix-bat-2
Wed, 22 Apr 2020 13:08:57 +0200, by Jan Mulder
Merged in Ideenmodellierer/ostc4/Improve_Logtansfer (pull request #42)
Wed, 15 Apr 2020 07:01:11 +0000, by heinrichsweikamp
Removed no longer needed reset profile function: Improve_Logtansfer
Tue, 14 Apr 2020 19:45:34 +0200, by ideenmodellierer
Moved and deactivated analyse sample buffer switch: Improve_Logtansfer
Tue, 14 Apr 2020 19:44:19 +0200, by ideenmodellierer
Cmd Get profile: transmit dummy profile if necessary Improve_Logtansfer
Tue, 14 Apr 2020 19:29:23 +0200, by ideenmodellierer
Removed invalidate header function because it is no lonnger needed Improve_Logtansfer
Tue, 14 Apr 2020 19:27:04 +0200, by ideenmodellierer
Compare profile length from header and sample data to identify valid profiles Improve_Logtansfer
Tue, 14 Apr 2020 19:22:56 +0200, by ideenmodellierer
Added compile switch to handle additional data during raw header request: Improve_Logtansfer
Mon, 13 Apr 2020 16:00:54 +0200, by ideenmodellierer
Added function to transfer sample buffer: Improve_Logtansfer
Sun, 12 Apr 2020 21:02:34 +0200, by ideenmodellierer
Power-down Bluetooth on COMM exit
Wed, 08 Apr 2020 16:34:54 +0200, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/minor_improvments (pull request #41)
Mon, 30 Mar 2020 13:16:11 +0000, by heinrichsweikamp
merged default into minor_improvments minor_improvments
Sun, 29 Mar 2020 21:55:00 +0200, by Ideenmodellierer
Activated reset of sample information within header data at time of sector erasing: minor_improvments
Sun, 29 Mar 2020 21:39:57 +0200, by ideenmodellierer
Added ppO2 to dummy profile data: minor_improvments
Sat, 28 Mar 2020 21:41:47 +0100, by ideenmodellierer
Eliminated some minor warnings minor_improvments
Tue, 24 Mar 2020 22:32:48 +0100, by ideenmodellierer
Transfer a dummy profile in case of missing sample information: minor_improvments
Tue, 24 Mar 2020 22:14:16 +0100, by ideenmodellierer
Reactivated samples for bottle pressure information: minor_improvments
Tue, 24 Mar 2020 22:12:08 +0100, by ideenmodellierer
Reactivated samples for bottle pressure information: minor_improvments
Tue, 24 Mar 2020 22:08:29 +0100, by ideenmodellierer
Added compile variant enabling the reset of profile sample information: minor_improvments
Tue, 24 Mar 2020 21:59:38 +0100, by ideenmodellierer
Added compile variant enabling the reset of profile sample information: minor_improvments
Tue, 24 Mar 2020 21:59:11 +0100, by ideenmodellierer
Allocate received bar value to active gas (was static allocated to gas[1]) minor_improvments
Tue, 24 Mar 2020 21:49:52 +0100, by ideenmodellierer
Added new compile switches for variants: minor_improvments
Tue, 24 Mar 2020 21:48:27 +0100, by ideenmodellierer
Added initialization of bottle sensor data age counter minor_improvments
Mon, 23 Mar 2020 21:14:54 +0100, by ideenmodellierer
Added compile switch to show voltage parallel to charge status percantage minor_improvments
Mon, 23 Mar 2020 21:13:52 +0100, by ideenmodellierer
Added compile switch var firmware variant which does trust the memory log => does not check the log consistency at startu (used for test purpose) minor_improvments
Mon, 23 Mar 2020 21:10:02 +0100, by ideenmodellierer
Introduced configuration header for variant managment: minor_improvments
Thu, 05 Mar 2020 22:31:50 +0100, by ideenmodellierer
Removed duplicated definition: minor_improvments
Thu, 05 Mar 2020 22:27:55 +0100, by ideenmodellierer
Introduced enum for lower left corner view selection: minor_improvments
Sat, 29 Feb 2020 22:27:29 +0100, by ideenmodellierer
Introduced enum for lower left corner view selection: minor_improvments
Sat, 29 Feb 2020 22:27:04 +0100, by ideenmodellierer
Introduced enum for lower left corner view selection: minor_improvments
Sat, 29 Feb 2020 22:25:20 +0100, by ideenmodellierer
fix potential issue with >255 dives in the logbook
Sun, 01 Mar 2020 10:06:45 +0100, by heinrichsweikamp
Added tag v1.5.3 release for changeset 5b4c78c36b04
Thu, 27 Feb 2020 09:13:25 +0100, by heinrichsweikamp
1.5.3 release v1.5.3 release
Thu, 27 Feb 2020 09:13:08 +0100, by heinrichsweikamp
update the 1.5.3 for tests
Mon, 24 Feb 2020 15:17:54 +0100, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/Improve_BatteryGasGauge (pull request #40)
Mon, 24 Feb 2020 07:58:37 +0000, by heinrichsweikamp
Moved power on detection to RTE: Improve_BatteryGasGauge
Sun, 23 Feb 2020 21:18:49 +0100, by ideenmodellierer
Bugfix display battery voltage in maintainance menu: Improve_BatteryGasGauge
Sun, 23 Feb 2020 21:17:17 +0100, by ideenmodellierer
Reduced timeout for common UART communication: Improve_BatteryGasGauge
Sun, 23 Feb 2020 21:13:28 +0100, by ideenmodellierer
Detect startup after power off: Improve_BatteryGasGauge
Sun, 23 Feb 2020 21:09:56 +0100, by ideenmodellierer
show battery percent and voltage and surfacemode. That gives additional
Tue, 18 Feb 2020 12:41:45 +0100, by heinrichsweikamp
make a 1.5.3 for tests
Tue, 18 Feb 2020 09:58:52 +0100, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/ImprovmentNVM_2 (pull request #39)
Tue, 18 Feb 2020 07:20:29 +0000, by heinrichsweikamp
Marked possible code improvment for future activities: ImprovmentNVM_2
Mon, 17 Feb 2020 19:43:09 +0100, by ideenmodellierer
Activated ringbuffer for settings: ImprovmentNVM_2
Mon, 17 Feb 2020 19:04:10 +0100, by ideenmodellierer
Activated ringbuffer for settings: ImprovmentNVM_2
Sun, 16 Feb 2020 22:04:52 +0100, by ideenmodellierer
Added function to analyse the sampel ringbuffer: ImprovmentNVM_2
Sat, 15 Feb 2020 20:50:58 +0100, by ideenmodellierer
Added function to analyse the sampel ringbuffer: ImprovmentNVM_2
Sat, 15 Feb 2020 20:50:20 +0100, by ideenmodellierer
Added (optional) menu item to analyse log sample buffer: ImprovmentNVM_2
Sat, 15 Feb 2020 20:45:19 +0100, by ideenmodellierer
ext_Flash_write_sample erase sector optimization: ImprovmentNVM_2
Mon, 10 Feb 2020 19:40:33 +0100, by ideenmodellierer
Moved Timeout handling out of 100ms callback: ImprovmentNVM_2
Mon, 10 Feb 2020 19:29:12 +0100, by ideenmodellierer
Enable sequentionel writing of device data: ImprovmentNVM_2
Mon, 10 Feb 2020 19:25:09 +0100, by ideenmodellierer
Optimize ef_write_block function: ImprovmentNVM_2
Mon, 10 Feb 2020 19:15:27 +0100, by ideenmodellierer
Merged in janlmulder/ostc4/maintain-2 (pull request #38)
Mon, 10 Feb 2020 08:23:15 +0000, by heinrichsweikamp
Added tag v1.5.2.beta release for changeset 54a480c43e97 maintain-2
Fri, 07 Feb 2020 16:38:11 +0100, by Jan Mulder
1.5.2 beta with RTE 2.02 v1.5.2.beta release
Wed, 15 Jan 2020 13:41:01 +0100, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/Improment_NVM (pull request #37)
Wed, 15 Jan 2020 10:53:15 +0000, by heinrichsweikamp
merged default into Improvment_NVM Improment_NVM
Tue, 14 Jan 2020 21:52:15 +0100, by Ideenmodellierer
Added compile switch for restoring of last known date after power lost: Improment_NVM
Tue, 14 Jan 2020 21:38:45 +0100, by ideenmodellierer
Bugfix Flipdisplay Gauge and Apnoe mode: Improment_NVM
Tue, 14 Jan 2020 21:10:37 +0100, by ideenmodellierer
Bugfix: Warnings displayed in Gauge Mode: Improment_NVM
Tue, 14 Jan 2020 21:08:45 +0100, by ideenmodellierer
Bugfix: Limit log length in case of corrupted sample storage: Improment_NVM
Mon, 13 Jan 2020 20:27:57 +0100, by ideenmodellierer
Bugfix display compass calibration frozen: Improment_NVM
Sun, 12 Jan 2020 21:33:13 +0100, by ideenmodellierer
Restore last known date: After a power off RTC looses time data and restarts in the year 2000. Code will fix this date to the year 2016. This change will set the date to the last known date of the operation hour counter Improment_NVM
Sun, 12 Jan 2020 19:55:22 +0100, by ideenmodellierer
Bugfix invalid voltage / temperatur after coldstart: Improment_NVM
Sun, 12 Jan 2020 19:50:14 +0100, by ideenmodellierer
Bugfix parallel call of external flash functions: Improment_NVM
Sun, 12 Jan 2020 18:06:59 +0100, by ideenmodellierer
Bugfix Min max values for device data checks: Improment_NVM
Sun, 12 Jan 2020 17:57:11 +0100, by ideenmodellierer
Bugfix Display of Sensor values: Improment_NVM
Sun, 12 Jan 2020 17:47:02 +0100, by ideenmodellierer
Bugfix: display of time of minimum voltag: Improment_NVM
Sun, 12 Jan 2020 17:45:36 +0100, by ideenmodellierer
We got one report of false/freezd depth reading when jumping into 2m depth
Wed, 08 Jan 2020 15:35:15 +0100, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/ImproveBluetooth (pull request #36)
Sun, 05 Jan 2020 14:57:50 +0000, by heinrichsweikamp
merged default into ImproveBluetooth ImproveBluetooth
Sun, 29 Dec 2019 09:42:16 +0100, by Ideenmodellierer
Added retry through power off/on cycle: ImproveBluetooth
Sat, 28 Dec 2019 19:42:04 +0100, by ideenmodellierer
Revert change to keep connection open in case of BlueMod messages: ImproveBluetooth
Sat, 21 Dec 2019 20:21:26 +0100, by ideenmodellierer
Bugfix: Merge / cleanup problem: ImproveBluetooth
Mon, 02 Dec 2019 22:03:05 +0100, by ideenmodellierer
Added missing enum for configuration states ImproveBluetooth
Sun, 01 Dec 2019 19:55:15 +0100, by ideenmodellierer
Added function for BlueMod configuration: ImproveBluetooth
Tue, 26 Nov 2019 22:12:25 +0100, by ideenmodellierer
Added start of module configuration after eache modul power on ImproveBluetooth
Tue, 26 Nov 2019 21:17:57 +0100, by ideenmodellierer
Added start of module configuration after eache modul power on ImproveBluetooth
Tue, 26 Nov 2019 21:16:36 +0100, by ideenmodellierer
Configurate FlowCntrl Pins as noPull ImproveBluetooth
Tue, 26 Nov 2019 21:14:58 +0100, by ideenmodellierer
Bugfix negativ ascend bar: ImproveBluetooth
Tue, 26 Nov 2019 18:13:26 +0100, by ideenmodellierer
Move Constants and libm to start of firmware ROM block: ImproveBluetooth
Tue, 26 Nov 2019 18:02:48 +0100, by ideenmodellierer
Merged in janlmulder/ostc4/maintain-1 (pull request #35)
Mon, 02 Dec 2019 07:56:47 +0000, by heinrichsweikamp
Fix case for case sensitive OS maintain-1
Sun, 01 Dec 2019 17:28:35 +0100, by Jan Mulder
Added tag v1.5.1 release for changeset afa55a50cc72 maintain-1
Sun, 01 Dec 2019 17:12:27 +0100, by Jan Mulder
Merged in Ideenmodellierer/ostc4/MotionDetection (pull request #34)
Sun, 24 Nov 2019 15:46:58 +0000, by heinrichsweikamp
Added key direction awarness to t3, t5 and t6 views: MotionDetection
Mon, 21 Oct 2019 21:16:53 +0200, by ideenmodellierer
Finetune parameter for detection of small sectors as used for the pitch detection MotionDetection
Mon, 21 Oct 2019 18:37:43 +0200, by ideenmodellierer
Consider number of available t3 views in sector handling: MotionDetection
Thu, 17 Oct 2019 23:09:17 +0200, by ideenmodellierer
Combine variables in a structure to improve readability of code MotionDetection
Thu, 17 Oct 2019 21:15:42 +0200, by ideenmodellierer
merge default MotionDetection
Thu, 10 Oct 2019 22:26:03 +0200, by Ideenmodellierer
Simplified pitch detection state machine: MotionDetection
Thu, 10 Oct 2019 22:11:59 +0200, by ideenmodellierer
Minor code cleanup MotionDetection
Thu, 10 Oct 2019 22:09:52 +0200, by ideenmodellierer
Added missing customerview selection MotionDetection
Mon, 16 Sep 2019 22:49:34 +0200, by ideenmodellierer
Incremented "idle window" for scroll detection MotionDetection
Mon, 16 Sep 2019 22:46:24 +0200, by ideenmodellierer
Motion events effect custom view in dive mode only MotionDetection
Mon, 16 Sep 2019 20:57:40 +0200, by ideenmodellierer
Added string for Empty/ Debug custom view selection MotionDetection
Mon, 16 Sep 2019 20:21:06 +0200, by ideenmodellierer
Use Enum values for initialization and setting check: MotionDetection
Tue, 10 Sep 2019 20:51:55 +0200, by ideenmodellierer
Removed some warnings MotionDetection
Sun, 08 Sep 2019 13:45:43 +0200, by ideenmodellierer
Add scroll event by pitch angle detection: MotionDetection
Sun, 08 Sep 2019 13:45:17 +0200, by ideenmodellierer
merged default into MotionDetection MotionDetection
Mon, 19 Aug 2019 17:50:55 +0200, by Ideenmodellierer
Added parameter for number of sectors to be defined MotionDetection
Mon, 19 Aug 2019 17:39:47 +0200, by ideenmodellierer
Changed function names from shake to pitch and improved detection function: Shake might be confusing for people reading the code because pitch values are ased for calculation => changed name to pitch to be more transparent MotionDetection
Tue, 13 Aug 2019 21:13:54 +0200, by ideenmodellierer
Added a function to count the active custom views. MotionDetection
Tue, 13 Aug 2019 21:12:17 +0200, by ideenmodellierer
Added menu item for motion detection. There are several possibility to use motion detection for user action input. To select of the a new menu entry has been added to the Sys2 =>Custom View Menu (Variables in german) MotionDetection
Tue, 13 Aug 2019 21:10:46 +0200, by ideenmodellierer
Merge default MotionDetection
Sat, 20 Jul 2019 21:42:45 +0200, by Ideenmodellierer
Fix misalignment of do while loop MotionDetection
Mon, 17 Jun 2019 19:56:38 +0200, by ideenmodellierer
Bugfix: selection of current view not working MotionDetection
Mon, 17 Jun 2019 19:53:01 +0200, by ideenmodellierer
Update call of motion detection function MotionDetection
Mon, 17 Jun 2019 19:47:07 +0200, by ideenmodellierer
Reworked detection function MotionDetection
Mon, 17 Jun 2019 19:46:18 +0200, by ideenmodellierer
Parameter update MotionDetection
Tue, 11 Jun 2019 05:31:07 +0200, by Ideenmodellierer
Pass action to customer vie update function. MotionDetection
Tue, 11 Jun 2019 05:30:09 +0200, by Ideenmodellierer
Added trigger of middle button action in case of a detected shake MotionDetection
Fri, 24 May 2019 22:01:46 +0200, by ideenmodellierer
Added new files for motion detection (shaking) detection MotionDetection
Fri, 24 May 2019 22:00:38 +0200, by ideenmodellierer
Add Support for new end-2019 hardware:
Sun, 24 Nov 2019 16:08:29 +0100, by heinrichsweikamp
Add Support for new end-2019 hardware:
Sat, 23 Nov 2019 18:39:50 +0100, by heinrichsweikamp
Add Support for new end-2019 hardware:
Sat, 23 Nov 2019 15:36:38 +0100, by heinrichsweikamp
Make a FW 1.5.1 / RTE 2.0 binary for testing v1.5.1 release
Wed, 09 Oct 2019 20:05:47 +0200, by heinrichsweikamp
Merged in janlmulder/ostc4/fix-merge-mess (pull request #33)
Wed, 09 Oct 2019 07:08:43 +0000, by heinrichsweikamp
Added tag v1.5.0 release for changeset 143fe85f82a2 fix-merge-mess
Tue, 08 Oct 2019 16:41:57 +0200, by Jan Mulder
Fix merge problem fix-merge-mess
Tue, 08 Oct 2019 16:35:45 +0200, by Jan Mulder
Merge
Sun, 06 Oct 2019 14:12:41 +0200, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/FlightMode_Improvment (pull request #32)
Sun, 06 Oct 2019 11:58:36 +0000, by heinrichsweikamp
Decrease ManualExitDiveCounter in surface mode FlightMode_Improvment
Thu, 03 Oct 2019 21:39:28 +0200, by ideenmodellierer
Minor changes to debug view FlightMode_Improvment
Thu, 03 Oct 2019 21:34:52 +0200, by ideenmodellierer
Added option to manually leave dive mode to system menu FlightMode_Improvment
Thu, 03 Oct 2019 21:33:47 +0200, by ideenmodellierer
Added function to support manuel exit of dive mode FlightMode_Improvment
Thu, 03 Oct 2019 21:30:16 +0200, by ideenmodellierer
Added function to evaluate the state of the surface pressure history memory FlightMode_Improvment
Thu, 03 Oct 2019 21:26:46 +0200, by ideenmodellierer
Removed not used wireless menu items FlightMode_Improvment
Tue, 01 Oct 2019 19:58:58 +0200, by ideenmodellierer
Added compile switch to enable debug view option in system menu FlightMode_Improvment
Tue, 01 Oct 2019 19:43:30 +0200, by ideenmodellierer
Removed averaging of pressure and temperatur values FlightMode_Improvment
Tue, 01 Oct 2019 19:13:41 +0200, by ideenmodellierer
change max. allowed surface pressure to 1030hPa (As in the small OSTC)
Sun, 06 Oct 2019 14:07:51 +0200, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/PressureMeasure_Improvment (pull request #31)
Mon, 19 Aug 2019 11:42:31 +0000, by heinrichsweikamp
Apply averaging to pressure measurement: In pre versions calculated pressure value jittered +/-10hPa. Since we measure the pressure several time a second but only use one value a second, calc average including not used values PressureMeasure_Improvment
Sat, 17 Aug 2019 19:03:47 +0200, by ideenmodellierer
Added function to avoid divemode activation during Landing: PressureMeasure_Improvment
Sat, 17 Aug 2019 18:57:15 +0200, by ideenmodellierer
Set Max value for pressure offset to 50mBar (20mBar before) PressureMeasure_Improvment
Sat, 17 Aug 2019 18:47:08 +0200, by ideenmodellierer
Show actual instead of surface (30minute old) pressure if the actual differs significant (e.g. in plane or during pressure testing) PressureMeasure_Improvment
Sat, 17 Aug 2019 18:44:43 +0200, by ideenmodellierer
Use average calculation for pressure: precondition was that pressure values jittered +- 10 HPa from one capture (once a second) to the other. Basically pressure is measured several times a second => using these values in an additional history calculation reduces the jitter down to +-1 per second PressureMeasure_Improvment
Tue, 13 Aug 2019 21:46:26 +0200, by ideenmodellierer
building a 1.5 v1.5.0 release
Sun, 04 Aug 2019 11:01:06 +0200, by heinrichsweikamp
add update files for testing purposes
Sat, 20 Jul 2019 10:44:01 +0200, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/I2C_Improvment (pull request #30)
Thu, 18 Jul 2019 14:26:56 +0000, by heinrichsweikamp
Added plausibility check for pressure values I2C_Improvment
Wed, 17 Jul 2019 22:43:51 +0200, by ideenmodellierer
Added check of configuration. I2C_Improvment
Wed, 17 Jul 2019 22:43:16 +0200, by ideenmodellierer
Improved startup robustness I2C_Improvment
Wed, 17 Jul 2019 22:42:55 +0200, by ideenmodellierer
Set I2C speed to 88kHz, use digital filter only and reworked idle clock recovery I2C_Improvment
Wed, 17 Jul 2019 22:42:15 +0200, by ideenmodellierer
Deactivated internal pullups and I2C interrupt callback I2C_Improvment
Wed, 17 Jul 2019 22:41:31 +0200, by ideenmodellierer
Merged in janlmulder/ostc4/fix-batt-1 (pull request #29)
Mon, 01 Jul 2019 14:18:39 +0000, by heinrichsweikamp
bugfix: implement battery at end in dive header fix-batt-1
Thu, 20 Jun 2019 14:24:57 +0200, by Jan Mulder
increase RTE to 1.9 and Firmware to 1.4.9 beta
Sun, 30 Jun 2019 22:12:15 +0200, by heinrichsweikamp
Merged in Ideenmodellierer/ostc4/O2_SensorSync (pull request #28)
Sun, 30 Jun 2019 19:52:46 +0000, by heinrichsweikamp
Added start of frame detection for HUD data O2_SensorSync
Sun, 30 Jun 2019 21:25:58 +0200, by ideenmodellierer
Moved indication variable for received HUD data to tCCR file. O2_SensorSync
Sun, 30 Jun 2019 21:18:05 +0200, by ideenmodellierer
Merged in janlmulder/ostc4/fix-version (pull request #27)
Wed, 19 Jun 2019 13:12:25 +0000, by heinrichsweikamp
bugfix: correct packed main version number in dive header fix-version
Wed, 19 Jun 2019 14:31:50 +0200, by Jan Mulder
Merged in Ideenmodellierer/ostc4/Bugfix_Flip_FirmwareUpdate (pull request #26)
Wed, 19 Jun 2019 13:12:01 +0000, by heinrichsweikamp
Resolved warning Bugfix_Flip_FirmwareUpdate
Mon, 17 Jun 2019 21:47:54 +0200, by ideenmodellierer
Bugfix text display in update mode (flipped display) and reduction of timeout in case of a failed firmware update Bugfix_Flip_FirmwareUpdate
Mon, 17 Jun 2019 21:47:33 +0200, by ideenmodellierer
Bugfix Overview, O2 values and mV in flip display mode Bugfix_Flip_FirmwareUpdate
Mon, 17 Jun 2019 21:47:19 +0200, by ideenmodellierer
Reinitialize logos after flip of display Bugfix_Flip_FirmwareUpdate
Mon, 17 Jun 2019 21:46:56 +0200, by ideenmodellierer
Minor: Remove unused compass header file. The LSM303DLHC is not used in any hardware sold.
Sat, 01 Jun 2019 10:12:15 +0200, by heinrichsweikamp
Merged in janlmulder/ostc4/cleanup-4 (pull request #25)
Fri, 31 May 2019 06:22:50 +0000, by heinrichsweikamp
bugfix: make stopwatch and divetime run in sync cleanup-4
Wed, 29 May 2019 14:02:27 +0200, by Jan Mulder
Make dive mode detection more advanced cleanup-4
Sun, 26 May 2019 10:09:22 +0200, by Jan Mulder
cleanup: factor out SHelper typedef (and more) cleanup-4
Fri, 24 May 2019 09:29:29 +0200, by Jan Mulder
cleanup: introduce function setAvgDepth cleanup-4
Fri, 24 May 2019 09:02:46 +0200, by Jan Mulder
cleanup: factor out unused stopwatch code cleanup-4
Wed, 22 May 2019 22:22:15 +0200, by Jan Mulder
bugfix, cleanup: do not clip depth to 0 cleanup-4
Wed, 22 May 2019 14:39:04 +0200, by Jan Mulder
bugfix, consistency: show deco/NDL really after 1 minute divetime cleanup-4
Tue, 21 May 2019 11:11:05 +0200, by Jan Mulder
bugfix, simulator: fix the 1 sec difference between stopwatch and divetime cleanup-4
Mon, 20 May 2019 13:06:02 +0200, by Jan Mulder
bugfix, cleanup: simplify stopwatch logic and fix fallout cleanup-4
Mon, 20 May 2019 12:57:31 +0200, by Jan Mulder
bugfix, cleanup: keep both is_ambient_pressure_close_to_surface in sync cleanup-4
Mon, 20 May 2019 10:13:44 +0200, by Jan Mulder
cleanup, RTE: factor out scheduleCheck_pressure_reached_dive_mode_level cleanup-4
Mon, 20 May 2019 10:05:27 +0200, by Jan Mulder
cleanup: remove commented/unused code, make static cleanup-4
Fri, 17 May 2019 21:19:04 +0200, by Jan Mulder
Merged in janlmulder/ostc4/cleanup-3 (pull request #24)
Fri, 17 May 2019 06:38:56 +0000, by heinrichsweikamp
Bugfix: fix drawing of CCR bailout profile cleanup-3
Thu, 16 May 2019 14:02:46 +0200, by Jan Mulder
cleanup: remove unused code, make static, remove commented code cleanup-3
Thu, 16 May 2019 08:56:15 +0200, by Jan Mulder
Possible bugfix: do not use bitwise and (&) cleanup-3
Thu, 16 May 2019 08:54:33 +0200, by Jan Mulder
Merged in janlmulder/ostc4/div-fixes-6 (pull request #23)
Mon, 13 May 2019 13:37:34 +0000, by heinrichsweikamp
Added tag v1.4.8 release for changeset ba9d99a2e310 div-fixes-6
Sun, 12 May 2019 09:45:32 +0200, by Jan Mulder
bugfix, consistency: show deco, NDL after 1 minute div-fixes-6
Thu, 02 May 2019 10:05:28 +0200, by Jan Mulder
translate: nullzeit -> ndl div-fixes-6
Thu, 02 May 2019 09:24:54 +0200, by Jan Mulder
Deco Models: limit NDL to 240 minutes div-fixes-6
Thu, 02 May 2019 09:16:07 +0200, by Jan Mulder
VPM, cleanup: 1st round div-fixes-6
Thu, 02 May 2019 08:43:07 +0200, by Jan Mulder
cleanup: remove unused code div-fixes-6
Mon, 29 Apr 2019 19:45:25 +0200, by Jan Mulder
cleanup: no useless checks for simulator state div-fixes-6
Mon, 29 Apr 2019 19:43:05 +0200, by Jan Mulder
Update the release file for testing. Rev 286 did not include the 1.4.8 (non-beta) firmware. v1.4.8 release
Mon, 06 May 2019 15:45:19 +0200, by heinrichsweikamp
Minor: Some Texts fixed, allign RTErequired* values with RTE firmware
Mon, 06 May 2019 09:00:58 +0200, by heinrichsweikamp
add update files for testing purposes
Sun, 05 May 2019 11:06:02 +0200, by heinrichsweikamp
Merged in janlmulder/ostc4/ndl-in-logbook (pull request #22)
Thu, 02 May 2019 11:12:25 +0000, by heinrichsweikamp
Bugfix: write NDL in logbook correctly ndl-in-logbook
Thu, 02 May 2019 13:08:17 +0200, by Jan Mulder
translate some comments into english
Wed, 01 May 2019 14:45:47 +0200, by heinrichsweikamp
Fix typos (There are still many...)
Wed, 01 May 2019 14:39:46 +0200, by heinrichsweikamp
Make RTE show as 1.8.0 beta, add update files for testing purposes
Mon, 29 Apr 2019 19:25:24 +0200, by heinrichsweikamp

less more | rev 727: (0) -448 tip

Mercurial > public > ostc4

graph