Mercurial > public > ostc4
graph
-
Cleanup sensor data interface:Sun, 04 Jun 2023 21:54:24 +0200, by Ideenmodellierer
-
Change support from Pyroscience -> DiveO2 sensorsWed, 31 May 2023 08:44:07 +0200, by heinrichsweikamp
-
Bugfixloop UART multiplexer integration:Tue, 30 May 2023 18:44:20 +0200, by Ideenmodellierer
-
Update digital O2 sensor information:Mon, 29 May 2023 20:26:38 +0200, by Ideenmodellierer
-
Sensor status support for multiplexed DiveO2 sensors:Mon, 29 May 2023 20:22:15 +0200, by Ideenmodellierer
-
Update real multiplexer implementation:Mon, 29 May 2023 18:26:55 +0200, by Ideenmodellierer
-
Discovery<=>SmallCPU inferface update:Tue, 23 May 2023 21:50:19 +0200, by Ideenmodellierer
-
Added UART multiplexer support for DiveO2:Tue, 23 May 2023 21:45:34 +0200, by Ideenmodellierer
-
Zusammenf?hrenMon, 22 May 2023 09:15:09 +0200, by heinrichsweikamp
-
This is only showing if one of the compass views is visible. It should make it possible to verify that a correct heading is set as the user can see the compass readout when pushing the button. (mikeller)Mon, 22 May 2023 09:14:27 +0200, by heinrichsweikamp
-
Add support for a configurable compass declination in a range of -99 to 99 degrees.Thu, 18 May 2023 09:49:17 +0200, by heinrichsweikamp
-
Add a shortcuts to change the setpoint to the loop to the 'normal' display when diving. It is only shown when diving in CCR mode and on the loop.Thu, 11 May 2023 12:13:03 +0200, by heinrichsweikamp
-
more menu items for the compass menu: Delete bearing, and reset to land based bearing. I have also re-enabled the real time bearing display in the menu - makes it easier to set the correct bearing. (mikeller)Wed, 10 May 2023 16:25:39 +0200, by heinrichsweikamp
-
Menu shortcut for bailout / return to circuit when diving in CCR mode (mikeller)Wed, 10 May 2023 16:24:57 +0200, by heinrichsweikamp
-
Revised automatic setpoint change. The proposed approach is essentially the approach used by most controllers of eCCR ('upshift' on descent, 'downshift' on ascent), so that the OSTC4 when used as a backup computer for eCCR will make the changes at the same time as the eCCR itself.Fri, 21 Apr 2023 09:48:23 +0200, by heinrichsweikamp
-
Deactivation of the 'fallback' option when the CCR mode is set to 'Fixed' - this makes it a little clearer that the option has no influence in this mode.Fri, 21 Apr 2023 09:47:06 +0200, by heinrichsweikamp
-
1.6.2 releaseThu, 13 Apr 2023 09:35:43 +0200, by heinrichsweikamp
-
Update build for testingWed, 12 Apr 2023 09:56:00 +0200, by heinrichsweikamp
-
change button default responsiveness to 100Wed, 12 Apr 2023 09:30:15 +0200, by heinrichsweikamp
-
After a firmware update, use the factory settings for button sensitivity if these exist, the default settings otherwise.Wed, 12 Apr 2023 09:24:44 +0200, by heinrichsweikamp
-
Update build for testingMon, 27 Mar 2023 10:04:53 +0200, by heinrichsweikamp
-
increase HAL_Delay to 10ms for cold-start-button resetSun, 26 Mar 2023 18:34:30 +0200, by heinrichsweikamp