Mercurial > public > ostc4
graph
-
Added UART multiplexer support for DiveO2:Tue, 23 May 2023 21:45:34 +0200, by Ideenmodellierer
-
Zusammenf?hrenMon, 22 May 2023 09:15:09 +0200, by heinrichsweikamp
-
This is only showing if one of the compass views is visible. It should make it possible to verify that a correct heading is set as the user can see the compass readout when pushing the button. (mikeller)Mon, 22 May 2023 09:14:27 +0200, by heinrichsweikamp
-
Add support for a configurable compass declination in a range of -99 to 99 degrees.Thu, 18 May 2023 09:49:17 +0200, by heinrichsweikamp
-
Add a shortcuts to change the setpoint to the loop to the 'normal' display when diving. It is only shown when diving in CCR mode and on the loop.Thu, 11 May 2023 12:13:03 +0200, by heinrichsweikamp
-
more menu items for the compass menu: Delete bearing, and reset to land based bearing. I have also re-enabled the real time bearing display in the menu - makes it easier to set the correct bearing. (mikeller)Wed, 10 May 2023 16:25:39 +0200, by heinrichsweikamp
-
Menu shortcut for bailout / return to circuit when diving in CCR mode (mikeller)Wed, 10 May 2023 16:24:57 +0200, by heinrichsweikamp
-
Revised automatic setpoint change. The proposed approach is essentially the approach used by most controllers of eCCR ('upshift' on descent, 'downshift' on ascent), so that the OSTC4 when used as a backup computer for eCCR will make the changes at the same time as the eCCR itself.Fri, 21 Apr 2023 09:48:23 +0200, by heinrichsweikamp
-
Deactivation of the 'fallback' option when the CCR mode is set to 'Fixed' - this makes it a little clearer that the option has no influence in this mode.Fri, 21 Apr 2023 09:47:06 +0200, by heinrichsweikamp
-
1.6.2 releaseThu, 13 Apr 2023 09:35:43 +0200, by heinrichsweikamp
-
Update build for testingWed, 12 Apr 2023 09:56:00 +0200, by heinrichsweikamp
-
change button default responsiveness to 100Wed, 12 Apr 2023 09:30:15 +0200, by heinrichsweikamp
-
After a firmware update, use the factory settings for button sensitivity if these exist, the default settings otherwise.Wed, 12 Apr 2023 09:24:44 +0200, by heinrichsweikamp
-
Update build for testingMon, 27 Mar 2023 10:04:53 +0200, by heinrichsweikamp
-
increase HAL_Delay to 10ms for cold-start-button resetSun, 26 Mar 2023 18:34:30 +0200, by heinrichsweikamp
-
Preparing a 1.6.2 release candidateSun, 26 Mar 2023 11:27:29 +0200, by heinrichsweikamp
-
Fix/handle negative scrubber timer valuesTue, 21 Mar 2023 12:57:37 +0100, by heinrichsweikamp
-
Quit simualted dives after the dive time set in the SIM tab.Tue, 21 Mar 2023 12:56:54 +0100, by heinrichsweikamp
-
Some compass improvements from mikellerFri, 17 Mar 2023 09:35:25 +0100, by heinrichsweikamp
-
- Colours for scrubber display when time remaining falls below a threshold valueWed, 15 Mar 2023 09:18:07 +0100, by heinrichsweikamp
-
Dev Bugfix: ignore analog out of bounds limits for DiveO2 sensor:Tue, 07 Mar 2023 22:14:20 +0100, by Ideenmodellierer
-
Added visualization of CO2 during dive:Tue, 07 Mar 2023 20:02:05 +0100, by Ideenmodellierer
-
Cleanup display of multiple warnings in T3 (Big font) view:Tue, 07 Mar 2023 19:59:02 +0100, by Ideenmodellierer
-
Only show autodetection in sensor menu if external interface is present:Tue, 07 Mar 2023 19:55:13 +0100, by Ideenmodellierer
-
Updated outdated commentTue, 07 Mar 2023 19:52:18 +0100, by Ideenmodellierer
-
Dev Bugfix: Alignment problem in lifedata structure:Tue, 07 Mar 2023 19:51:30 +0100, by Ideenmodellierer
-
resolv mergeMon, 13 Mar 2023 22:23:00 +0100, by Ideenmodellierer
-
Avoid blinking in customer view selection page:Sun, 05 Mar 2023 22:17:32 +0100, by Ideenmodellierer
-
Added enum for Co2 displayMon, 13 Mar 2023 22:18:28 +0100, by Ideenmodellierer
-
Added display of co2 ppm values:Sun, 05 Mar 2023 22:14:53 +0100, by Ideenmodellierer
-
Added pressure compensation to CO2 detection:Sun, 05 Mar 2023 22:06:47 +0100, by Ideenmodellierer
-
Code cleanup sensors under development:Tue, 21 Feb 2023 21:19:31 +0100, by Ideenmodellierer
-
Update Sentinel protocol:Sun, 19 Feb 2023 21:52:02 +0100, by Ideenmodellierer
-
Added DiveO2 fatal error detection:Sun, 19 Feb 2023 21:51:19 +0100, by Ideenmodellierer
-
Enable start dive in Big font display:Sun, 19 Feb 2023 21:48:47 +0100, by Ideenmodellierer
-
Update Sentinel protocol:Sun, 19 Feb 2023 21:43:24 +0100, by Ideenmodellierer
-
Added button lock after wakeup in surface mode:Thu, 02 Feb 2023 17:35:54 +0100, by Ideenmodellierer
-
Added button lock after wakeup in surface mode:Thu, 02 Feb 2023 17:35:38 +0100, by Ideenmodellierer
-
Enable start dive in Big font display:Thu, 02 Feb 2023 17:26:54 +0100, by Ideenmodellierer
-
Added data init function for external interface:Thu, 02 Feb 2023 17:19:24 +0100, by Ideenmodellierer
-
NEW: Add mini compass with marker declination indicationMon, 06 Mar 2023 16:03:00 +0100, by heinrichsweikamp
-
Fixed logbook download after switch from CCR to extra (OC) gas if the extra gasFri, 03 Mar 2023 10:41:44 +0100, by heinrichsweikamp
-
Fixed invalid setpoint (0.0) used after switch from CCR to extra (OC) gasTue, 14 Feb 2023 10:21:56 +0100, by heinrichsweikamp
-
Removed interface selection from sensor menu:Sun, 15 Jan 2023 21:51:54 +0100, by Ideenmodellierer
-
Optical sensor as default:Sun, 15 Jan 2023 21:48:34 +0100, by Ideenmodellierer
-
Fix compiler switch:Sun, 15 Jan 2023 21:45:14 +0100, by Ideenmodellierer
-
Improvment sensor Autodetection:Sun, 15 Jan 2023 21:43:33 +0100, by Ideenmodellierer
-
Update sensor menu support for automatic sensor detection:Sat, 14 Jan 2023 20:49:40 +0100, by Ideenmodellierer
-
Added auto detection functionality for sensors connected to the external interface:Sat, 14 Jan 2023 20:46:17 +0100, by Ideenmodellierer
-
Added sensor map to Firmware <=> RTE inferface:Sat, 14 Jan 2023 20:41:36 +0100, by Ideenmodellierer
-
Enabled CO2 support for beta test phase:Sat, 14 Jan 2023 20:37:20 +0100, by Ideenmodellierer
-
Bugfix data synchronization after RTE start:Sat, 14 Jan 2023 20:35:40 +0100, by Ideenmodellierer
-
Update CO2 sensor implementation:Sat, 07 Jan 2023 18:11:52 +0100, by Ideenmodellierer
-
Development feature: external pressure sensorThu, 05 Jan 2023 18:30:06 +0100, by Ideenmodellierer