view Small_CPU/Src/i2c.c @ 473:edfc1a464b42 Improve_Button_Sleep

Do not signal power on reset in case of a "warm" reset: The RTE signaled at every startup a coldstart to the firmware causing a reset of the button responsitivness to default. Even for example after a firmware update. The reset of the values is a wanted behavior in case a value was set which makes it impossible to operate the buttons. This is still possible by removing the battery => real cold start
author ideenmodellierer
date Tue, 12 May 2020 22:39:18 +0200
parents 4fe5400567e7
children
line wrap: on
line source

#include "baseCPU2.h"
#include "i2c.h"
#include "scheduler.h"

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/


//  ===============================================================================
//	I2C addresses - see i2c.h
//  ===============================================================================

I2C_HandleTypeDef I2cHandle;


/*
static void I2C_Error_Handler(void)
{
  while(1)
  {
  }
}
*/

GPIO_PinState HAL_I2C_Read_Data_PIN(void)
{
	return HAL_GPIO_ReadPin(I2Cx_SDA_GPIO_PORT,I2Cx_SDA_PIN);
}

void HAL_I2C_Send_One_CLOCK(void)
{
	HAL_GPIO_WritePin(I2Cx_SCL_GPIO_PORT, I2Cx_SCL_PIN, GPIO_PIN_RESET);
	HAL_Delay(1); 
	HAL_GPIO_WritePin(I2Cx_SCL_GPIO_PORT, I2Cx_SCL_PIN, GPIO_PIN_SET);
	HAL_Delay(1);
}

GPIO_PinState MX_I2C1_TestAndClear(void)
{
	GPIO_PinState retval;
	uint8_t repeatcnt = 3;

	I2C_DeInit();
	HAL_I2C_ManualControl_MspInit();
	
/* The SDA line is expected to be HIGH if no com is pending => send dummy clock signals if that is not the case */
	do
	{
		for(int i=0; i<20;i++)
		{
			if(HAL_I2C_Read_Data_PIN() == GPIO_PIN_RESET)
				HAL_I2C_Send_One_CLOCK();
			else
				break;
		}
		retval = HAL_I2C_Read_Data_PIN();
	}while ((repeatcnt-- > 0) && (retval != GPIO_PIN_SET));

	return retval;
}

HAL_StatusTypeDef MX_I2C1_Init(void)
{
  I2cHandle.Instance             = I2Cx;
  I2cHandle.Init.AddressingMode  = I2C_ADDRESSINGMODE_7BIT;
  I2cHandle.Init.ClockSpeed      = 88000; /* Reduced to avoid behavior described in errata: Mismatch on the “Setup time for a repeated Start condition” */
  I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
  I2cHandle.Init.DutyCycle       = I2C_DUTYCYCLE_2;				/* don't care if not in fast mode */
  I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLED;
  I2cHandle.Init.NoStretchMode   = I2C_NOSTRETCH_DISABLED;
  I2cHandle.Init.OwnAddress1     = 0x01;						/* don't care because of master mode */

/* According to documentation setting filters before I2C initialization is recommended */
	/* HAL_I2CEx_AnalogFilter_Config(&I2cHandle, I2C_ANALOGFILTER_ENABLED); */
	HAL_I2CEx_ConfigDigitalFilter(&I2cHandle,0x0F);

	global.I2C_SystemStatus = HAL_I2C_Init(&I2cHandle);

	if(global.dataSendToSlavePending)
	{
		scheduleSpecial_Evaluate_DataSendToSlave();
	}
	return global.I2C_SystemStatus;
}


void I2C_DeInit(void)
{
	HAL_I2C_DeInit(&I2cHandle);
}

static uint8_t i2c_errors = 0;

void I2C_Error_count(void)
{
	i2c_errors++;
}


HAL_StatusTypeDef I2C_Master_Transmit(  uint16_t DevAddress, uint8_t *pData, uint16_t Size)
{
	if(global.I2C_SystemStatus != HAL_OK)
		return global.I2C_SystemStatus;

	global.I2C_SystemStatus = HAL_I2C_Master_Transmit(&I2cHandle, DevAddress,  pData, Size, 10);
	if(global.I2C_SystemStatus != HAL_OK)
	{
		I2C_Error_count();
	}
	
	return global.I2C_SystemStatus;
}

HAL_StatusTypeDef I2C_Master_Receive(  uint16_t DevAddress, uint8_t *pData, uint16_t Size)
{
	if(global.I2C_SystemStatus != HAL_OK)
		return global.I2C_SystemStatus;

	global.I2C_SystemStatus = HAL_I2C_Master_Receive(&I2cHandle, DevAddress,  pData, Size, 10);
	if(global.I2C_SystemStatus != HAL_OK)
	{
		I2C_Error_count();
	}

	return global.I2C_SystemStatus;
}