Mercurial > public > ostc4
view Common/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim.c @ 729:d646a0f724a7
Added auto detection functionality for sensors connected to the external interface:
O2 sensors may be connected to the analog input as well as to the UART. The GUI visualization provides three slots for ppo2 display. Beside detection of sensor kind the task of the function is to place the available sensor in this three slots. CO2 has its own communication slot outside the ppo2 channel.
The result of the automatic detection is communicated via the sensor map.
author | Ideenmodellierer |
---|---|
date | Sat, 14 Jan 2023 20:46:17 +0100 |
parents | c78bcbd5deda |
children |
line wrap: on
line source
/** ****************************************************************************** * @file stm32f4xx_hal_tim.c * @author MCD Application Team * @brief TIM HAL module driver. * This file provides firmware functions to manage the following * functionalities of the Timer (TIM) peripheral: * + Time Base Initialization * + Time Base Start * + Time Base Start Interruption * + Time Base Start DMA * + Time Output Compare/PWM Initialization * + Time Output Compare/PWM Channel Configuration * + Time Output Compare/PWM Start * + Time Output Compare/PWM Start Interruption * + Time Output Compare/PWM Start DMA * + Time Input Capture Initialization * + Time Input Capture Channel Configuration * + Time Input Capture Start * + Time Input Capture Start Interruption * + Time Input Capture Start DMA * + Time One Pulse Initialization * + Time One Pulse Channel Configuration * + Time One Pulse Start * + Time Encoder Interface Initialization * + Time Encoder Interface Start * + Time Encoder Interface Start Interruption * + Time Encoder Interface Start DMA * + Commutation Event configuration with Interruption and DMA * + Time OCRef clear configuration * + Time External Clock configuration @verbatim ============================================================================== ##### TIMER Generic features ##### ============================================================================== [..] The Timer features include: (#) 16-bit up, down, up/down auto-reload counter. (#) 16-bit programmable prescaler allowing dividing (also on the fly) the counter clock frequency either by any factor between 1 and 65536. (#) Up to 4 independent channels for: (++) Input Capture (++) Output Compare (++) PWM generation (Edge and Center-aligned Mode) (++) One-pulse mode output ##### How to use this driver ##### ============================================================================== [..] (#) Initialize the TIM low level resources by implementing the following functions depending from feature used : (++) Time Base : HAL_TIM_Base_MspInit() (++) Input Capture : HAL_TIM_IC_MspInit() (++) Output Compare : HAL_TIM_OC_MspInit() (++) PWM generation : HAL_TIM_PWM_MspInit() (++) One-pulse mode output : HAL_TIM_OnePulse_MspInit() (++) Encoder mode output : HAL_TIM_Encoder_MspInit() (#) Initialize the TIM low level resources : (##) Enable the TIM interface clock using __TIMx_CLK_ENABLE(); (##) TIM pins configuration (+++) Enable the clock for the TIM GPIOs using the following function: __GPIOx_CLK_ENABLE(); (+++) Configure these TIM pins in Alternate function mode using HAL_GPIO_Init(); (#) The external Clock can be configured, if needed (the default clock is the internal clock from the APBx), using the following function: HAL_TIM_ConfigClockSource, the clock configuration should be done before any start function. (#) Configure the TIM in the desired functioning mode using one of the initialization function of this driver: (++) HAL_TIM_Base_Init: to use the Timer to generate a simple time base (++) HAL_TIM_OC_Init and HAL_TIM_OC_ConfigChannel: to use the Timer to generate an Output Compare signal. (++) HAL_TIM_PWM_Init and HAL_TIM_PWM_ConfigChannel: to use the Timer to generate a PWM signal. (++) HAL_TIM_IC_Init and HAL_TIM_IC_ConfigChannel: to use the Timer to measure an external signal. (++) HAL_TIM_OnePulse_Init and HAL_TIM_OnePulse_ConfigChannel: to use the Timer in One Pulse Mode. (++) HAL_TIM_Encoder_Init: to use the Timer Encoder Interface. (#) Activate the TIM peripheral using one of the start functions depending from the feature used: (++) Time Base : HAL_TIM_Base_Start(), HAL_TIM_Base_Start_DMA(), HAL_TIM_Base_Start_IT() (++) Input Capture : HAL_TIM_IC_Start(), HAL_TIM_IC_Start_DMA(), HAL_TIM_IC_Start_IT() (++) Output Compare : HAL_TIM_OC_Start(), HAL_TIM_OC_Start_DMA(), HAL_TIM_OC_Start_IT() (++) PWM generation : HAL_TIM_PWM_Start(), HAL_TIM_PWM_Start_DMA(), HAL_TIM_PWM_Start_IT() (++) One-pulse mode output : HAL_TIM_OnePulse_Start(), HAL_TIM_OnePulse_Start_IT() (++) Encoder mode output : HAL_TIM_Encoder_Start(), HAL_TIM_Encoder_Start_DMA(), HAL_TIM_Encoder_Start_IT(). (#) The DMA Burst is managed with the two following functions: HAL_TIM_DMABurst_WriteStart() HAL_TIM_DMABurst_ReadStart() @endverbatim ****************************************************************************** * @attention * * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2> * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ #include "stm32f4xx_hal.h" /** @addtogroup STM32F4xx_HAL_Driver * @{ */ /** @defgroup TIM TIM * @brief TIM HAL module driver * @{ */ #ifdef HAL_TIM_MODULE_ENABLED /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /** @addtogroup TIM_Private_Functions * @{ */ /* Private function prototypes -----------------------------------------------*/ static void TIM_OC1_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config); static void TIM_OC3_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config); static void TIM_OC4_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config); static void TIM_TI1_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter); static void TIM_TI2_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter); static void TIM_TI2_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter); static void TIM_TI3_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter); static void TIM_TI4_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter); static void TIM_ETR_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ExtTRGPrescaler, uint32_t TIM_ExtTRGPolarity, uint32_t ExtTRGFilter); static void TIM_ITRx_SetConfig(TIM_TypeDef* TIMx, uint16_t TIM_ITRx); static void TIM_DMAPeriodElapsedCplt(DMA_HandleTypeDef *hdma); static void TIM_DMATriggerCplt(DMA_HandleTypeDef *hdma); static void TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef *htim, TIM_SlaveConfigTypeDef * sSlaveConfig); /** * @} */ /* Exported functions --------------------------------------------------------*/ /** @defgroup TIM_Exported_Functions TIM Exported Functions * @{ */ /** @defgroup TIM_Exported_Functions_Group1 Time Base functions * @brief Time Base functions * @verbatim ============================================================================== ##### Time Base functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM base. (+) De-initialize the TIM base. (+) Start the Time Base. (+) Stop the Time Base. (+) Start the Time Base and enable interrupt. (+) Stop the Time Base and disable interrupt. (+) Start the Time Base and enable DMA transfer. (+) Stop the Time Base and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM Time base Unit according to the specified * parameters in the TIM_HandleTypeDef and create the associated handle. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Init(TIM_HandleTypeDef *htim) { /* Check the TIM handle allocation */ if(htim == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); if(htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; /* Init the low level hardware : GPIO, CLOCK, NVIC */ HAL_TIM_Base_MspInit(htim); } /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Set the Time Base configuration */ TIM_Base_SetConfig(htim->Instance, &htim->Init); /* Initialize the TIM state*/ htim->State= HAL_TIM_STATE_READY; return HAL_OK; } /** * @brief DeInitializes the TIM Base peripheral * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_DeInit(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); htim->State = HAL_TIM_STATE_BUSY; /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ HAL_TIM_Base_MspDeInit(htim); /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM Base MSP. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_Base_MspInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_Base_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM Base MSP. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_Base_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM Base generation. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Start(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Change the TIM state*/ htim->State= HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Base generation. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Stop(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the TIM state*/ htim->State= HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Base generation in interrupt mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Start_IT(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); /* Enable the TIM Update interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_UPDATE); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Base generation in interrupt mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Stop_IT(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); /* Disable the TIM Update interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_UPDATE); /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Base generation in DMA mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param pData The source Buffer address. * @param Length The length of data to be transferred from memory to peripheral. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Start_DMA(TIM_HandleTypeDef *htim, uint32_t *pData, uint16_t Length) { /* Check the parameters */ assert_param(IS_TIM_DMA_INSTANCE(htim->Instance)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if((pData == 0U) && (Length > 0)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)pData, (uint32_t)&htim->Instance->ARR, Length); /* Enable the TIM Update DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_UPDATE); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Base generation in DMA mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Stop_DMA(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_DMA_INSTANCE(htim->Instance)); /* Disable the TIM Update DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_UPDATE); /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group2 Time Output Compare functions * @brief Time Output Compare functions * @verbatim ============================================================================== ##### Time Output Compare functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM Output Compare. (+) De-initialize the TIM Output Compare. (+) Start the Time Output Compare. (+) Stop the Time Output Compare. (+) Start the Time Output Compare and enable interrupt. (+) Stop the Time Output Compare and disable interrupt. (+) Start the Time Output Compare and enable DMA transfer. (+) Stop the Time Output Compare and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM Output Compare according to the specified * parameters in the TIM_HandleTypeDef and create the associated handle. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Init(TIM_HandleTypeDef* htim) { /* Check the TIM handle allocation */ if(htim == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); if(htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_OC_MspInit(htim); } /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Init the base time for the Output Compare */ TIM_Base_SetConfig(htim->Instance, &htim->Init); /* Initialize the TIM state*/ htim->State= HAL_TIM_STATE_READY; return HAL_OK; } /** * @brief DeInitializes the TIM peripheral * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_DeInit(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); htim->State = HAL_TIM_STATE_BUSY; /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); /* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */ HAL_TIM_OC_MspDeInit(htim); /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM Output Compare MSP. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_OC_MspInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_OC_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM Output Compare MSP. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_OC_MspDeInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_OC_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM Output Compare signal generation. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channel to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Start(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); /* Enable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Output Compare signal generation. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channel to be disabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); /* Disable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Output Compare signal generation in interrupt mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channel to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); } break; case TIM_CHANNEL_2: { /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); } break; case TIM_CHANNEL_3: { /* Enable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3); } break; case TIM_CHANNEL_4: { /* Enable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4); } break; default: break; } /* Enable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Output Compare signal generation in interrupt mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channel to be disabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); } break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); } break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3); } break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4); } break; default: break; } /* Disable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Output Compare signal generation in DMA mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channel to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @param pData The source Buffer address. * @param Length The length of data to be transferred from memory to TIM peripheral * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if(((uint32_t)pData == 0U) && (Length > 0)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } switch (Channel) { case TIM_CHANNEL_1: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length); /* Enable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); } break; case TIM_CHANNEL_2: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length); /* Enable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); } break; case TIM_CHANNEL_3: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3,Length); /* Enable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); } break; case TIM_CHANNEL_4: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length); /* Enable the TIM Capture/Compare 4 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4); } break; default: break; } /* Enable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Output Compare signal generation in DMA mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channel to be disabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Disable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); } break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); } break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3); } break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4); } break; default: break; } /* Disable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group3 Time PWM functions * @brief Time PWM functions * @verbatim ============================================================================== ##### Time PWM functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM OPWM. (+) De-initialize the TIM PWM. (+) Start the Time PWM. (+) Stop the Time PWM. (+) Start the Time PWM and enable interrupt. (+) Stop the Time PWM and disable interrupt. (+) Start the Time PWM and enable DMA transfer. (+) Stop the Time PWM and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM PWM Time Base according to the specified * parameters in the TIM_HandleTypeDef and create the associated handle. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Init(TIM_HandleTypeDef *htim) { /* Check the TIM handle allocation */ if(htim == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); if(htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_PWM_MspInit(htim); } /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Init the base time for the PWM */ TIM_Base_SetConfig(htim->Instance, &htim->Init); /* Initialize the TIM state*/ htim->State= HAL_TIM_STATE_READY; return HAL_OK; } /** * @brief DeInitializes the TIM peripheral * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_DeInit(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); htim->State = HAL_TIM_STATE_BUSY; /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); /* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */ HAL_TIM_PWM_MspDeInit(htim); /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM PWM MSP. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_PWM_MspInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_PWM_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM PWM MSP. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_PWM_MspDeInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_PWM_MspDeInit could be implemented in the user file */ } /** * @brief Starts the PWM signal generation. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Start(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the PWM signal generation. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be disabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); /* Disable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Starts the PWM signal generation in interrupt mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channel to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); } break; case TIM_CHANNEL_2: { /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); } break; case TIM_CHANNEL_3: { /* Enable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3); } break; case TIM_CHANNEL_4: { /* Enable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4); } break; default: break; } /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the PWM signal generation in interrupt mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be disabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Stop_IT (TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); } break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); } break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3); } break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4); } break; default: break; } /* Disable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM PWM signal generation in DMA mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @param pData The source Buffer address. * @param Length The length of data to be transferred from memory to TIM peripheral * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if(((uint32_t)pData == 0U) && (Length > 0)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } switch (Channel) { case TIM_CHANNEL_1: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length); /* Enable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); } break; case TIM_CHANNEL_2: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length); /* Enable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); } break; case TIM_CHANNEL_3: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3,Length); /* Enable the TIM Output Capture/Compare 3 request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); } break; case TIM_CHANNEL_4: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length); /* Enable the TIM Capture/Compare 4 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4); } break; default: break; } /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM PWM signal generation in DMA mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be disabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Disable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); } break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); } break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3); } break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4); } break; default: break; } /* Disable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group4 Time Input Capture functions * @brief Time Input Capture functions * @verbatim ============================================================================== ##### Time Input Capture functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM Input Capture. (+) De-initialize the TIM Input Capture. (+) Start the Time Input Capture. (+) Stop the Time Input Capture. (+) Start the Time Input Capture and enable interrupt. (+) Stop the Time Input Capture and disable interrupt. (+) Start the Time Input Capture and enable DMA transfer. (+) Stop the Time Input Capture and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM Input Capture Time base according to the specified * parameters in the TIM_HandleTypeDef and create the associated handle. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Init(TIM_HandleTypeDef *htim) { /* Check the TIM handle allocation */ if(htim == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); if(htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_IC_MspInit(htim); } /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Init the base time for the input capture */ TIM_Base_SetConfig(htim->Instance, &htim->Init); /* Initialize the TIM state*/ htim->State= HAL_TIM_STATE_READY; return HAL_OK; } /** * @brief DeInitializes the TIM peripheral * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_DeInit(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); htim->State = HAL_TIM_STATE_BUSY; /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); /* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */ HAL_TIM_IC_MspDeInit(htim); /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM INput Capture MSP. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_IC_MspInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_IC_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM Input Capture MSP. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_IC_MspDeInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_IC_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM Input Capture measurement. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Start (TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); /* Enable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Input Capture measurement. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be disabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); /* Disable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Input Capture measurement in interrupt mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Start_IT (TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); } break; case TIM_CHANNEL_2: { /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); } break; case TIM_CHANNEL_3: { /* Enable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3); } break; case TIM_CHANNEL_4: { /* Enable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4); } break; default: break; } /* Enable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Input Capture measurement in interrupt mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be disabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); } break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); } break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3); } break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4); } break; default: break; } /* Disable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Input Capture measurement on in DMA mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @param pData The destination Buffer address. * @param Length The length of data to be transferred from TIM peripheral to memory. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if((pData == 0U) && (Length > 0)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } switch (Channel) { case TIM_CHANNEL_1: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData, Length); /* Enable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); } break; case TIM_CHANNEL_2: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData, Length); /* Enable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); } break; case TIM_CHANNEL_3: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)&htim->Instance->CCR3, (uint32_t)pData, Length); /* Enable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); } break; case TIM_CHANNEL_4: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)&htim->Instance->CCR4, (uint32_t)pData, Length); /* Enable the TIM Capture/Compare 4 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4); } break; default: break; } /* Enable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Input Capture measurement on in DMA mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be disabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance)); switch (Channel) { case TIM_CHANNEL_1: { /* Disable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); } break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); } break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3); } break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4); } break; default: break; } /* Disable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group5 Time One Pulse functions * @brief Time One Pulse functions * @verbatim ============================================================================== ##### Time One Pulse functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM One Pulse. (+) De-initialize the TIM One Pulse. (+) Start the Time One Pulse. (+) Stop the Time One Pulse. (+) Start the Time One Pulse and enable interrupt. (+) Stop the Time One Pulse and disable interrupt. (+) Start the Time One Pulse and enable DMA transfer. (+) Stop the Time One Pulse and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM One Pulse Time Base according to the specified * parameters in the TIM_HandleTypeDef and create the associated handle. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param OnePulseMode Select the One pulse mode. * This parameter can be one of the following values: * @arg TIM_OPMODE_SINGLE: Only one pulse will be generated. * @arg TIM_OPMODE_REPETITIVE: Repetitive pulses will be generated. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_Init(TIM_HandleTypeDef *htim, uint32_t OnePulseMode) { /* Check the TIM handle allocation */ if(htim == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); assert_param(IS_TIM_OPM_MODE(OnePulseMode)); if(htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_OnePulse_MspInit(htim); } /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Configure the Time base in the One Pulse Mode */ TIM_Base_SetConfig(htim->Instance, &htim->Init); /* Reset the OPM Bit */ htim->Instance->CR1 &= ~TIM_CR1_OPM; /* Configure the OPM Mode */ htim->Instance->CR1 |= OnePulseMode; /* Initialize the TIM state*/ htim->State= HAL_TIM_STATE_READY; return HAL_OK; } /** * @brief DeInitializes the TIM One Pulse * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_DeInit(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); htim->State = HAL_TIM_STATE_BUSY; /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ HAL_TIM_OnePulse_MspDeInit(htim); /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM One Pulse MSP. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_OnePulse_MspInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_OnePulse_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM One Pulse MSP. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_OnePulse_MspDeInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_OnePulse_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM One Pulse signal generation. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param OutputChannel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel) { /* Prevent unused argument(s) compilation warning */ UNUSED(OutputChannel); /* Enable the Capture compare and the Input Capture channels (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be enabled together No need to enable the counter, it's enabled automatically by hardware (the counter starts in response to a stimulus and generate a pulse */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM One Pulse signal generation. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param OutputChannel TIM Channels to be disable. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_Stop(TIM_HandleTypeDef *htim, uint32_t OutputChannel) { /* Prevent unused argument(s) compilation warning */ UNUSED(OutputChannel); /* Disable the Capture compare and the Input Capture channels (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be disabled together */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM One Pulse signal generation in interrupt mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param OutputChannel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel) { /* Enable the Capture compare and the Input Capture channels (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be enabled together No need to enable the counter, it's enabled automatically by hardware (the counter starts in response to a stimulus and generate a pulse */ /* Prevent unused argument(s) compilation warning */ UNUSED(OutputChannel); /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM One Pulse signal generation in interrupt mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param OutputChannel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_Stop_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel) { /* Prevent unused argument(s) compilation warning */ UNUSED(OutputChannel); /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); /* Disable the Capture compare and the Input Capture channels (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be disabled together */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); if(IS_TIM_ADVANCED_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Output */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group6 Time Encoder functions * @brief Time Encoder functions * @verbatim ============================================================================== ##### Time Encoder functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM Encoder. (+) De-initialize the TIM Encoder. (+) Start the Time Encoder. (+) Stop the Time Encoder. (+) Start the Time Encoder and enable interrupt. (+) Stop the Time Encoder and disable interrupt. (+) Start the Time Encoder and enable DMA transfer. (+) Stop the Time Encoder and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM Encoder Interface and create the associated handle. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param sConfig TIM Encoder Interface configuration structure * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Init(TIM_HandleTypeDef *htim, TIM_Encoder_InitTypeDef* sConfig) { uint32_t tmpsmcr = 0U; uint32_t tmpccmr1 = 0U; uint32_t tmpccer = 0U; /* Check the TIM handle allocation */ if(htim == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); assert_param(IS_TIM_ENCODER_MODE(sConfig->EncoderMode)); assert_param(IS_TIM_IC_SELECTION(sConfig->IC1Selection)); assert_param(IS_TIM_IC_SELECTION(sConfig->IC2Selection)); assert_param(IS_TIM_IC_POLARITY(sConfig->IC1Polarity)); assert_param(IS_TIM_IC_POLARITY(sConfig->IC2Polarity)); assert_param(IS_TIM_IC_PRESCALER(sConfig->IC1Prescaler)); assert_param(IS_TIM_IC_PRESCALER(sConfig->IC2Prescaler)); assert_param(IS_TIM_IC_FILTER(sConfig->IC1Filter)); assert_param(IS_TIM_IC_FILTER(sConfig->IC2Filter)); if(htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_Encoder_MspInit(htim); } /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Reset the SMS bits */ htim->Instance->SMCR &= ~TIM_SMCR_SMS; /* Configure the Time base in the Encoder Mode */ TIM_Base_SetConfig(htim->Instance, &htim->Init); /* Get the TIMx SMCR register value */ tmpsmcr = htim->Instance->SMCR; /* Get the TIMx CCMR1 register value */ tmpccmr1 = htim->Instance->CCMR1; /* Get the TIMx CCER register value */ tmpccer = htim->Instance->CCER; /* Set the encoder Mode */ tmpsmcr |= sConfig->EncoderMode; /* Select the Capture Compare 1 and the Capture Compare 2 as input */ tmpccmr1 &= ~(TIM_CCMR1_CC1S | TIM_CCMR1_CC2S); tmpccmr1 |= (sConfig->IC1Selection | (sConfig->IC2Selection << 8U)); /* Set the Capture Compare 1 and the Capture Compare 2 prescalers and filters */ tmpccmr1 &= ~(TIM_CCMR1_IC1PSC | TIM_CCMR1_IC2PSC); tmpccmr1 &= ~(TIM_CCMR1_IC1F | TIM_CCMR1_IC2F); tmpccmr1 |= sConfig->IC1Prescaler | (sConfig->IC2Prescaler << 8U); tmpccmr1 |= (sConfig->IC1Filter << 4U) | (sConfig->IC2Filter << 12U); /* Set the TI1 and the TI2 Polarities */ tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC2P); tmpccer &= ~(TIM_CCER_CC1NP | TIM_CCER_CC2NP); tmpccer |= sConfig->IC1Polarity | (sConfig->IC2Polarity << 4U); /* Write to TIMx SMCR */ htim->Instance->SMCR = tmpsmcr; /* Write to TIMx CCMR1 */ htim->Instance->CCMR1 = tmpccmr1; /* Write to TIMx CCER */ htim->Instance->CCER = tmpccer; /* Initialize the TIM state*/ htim->State= HAL_TIM_STATE_READY; return HAL_OK; } /** * @brief DeInitializes the TIM Encoder interface * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_DeInit(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); htim->State = HAL_TIM_STATE_BUSY; /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ HAL_TIM_Encoder_MspDeInit(htim); /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM Encoder Interface MSP. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_Encoder_MspInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_Encoder_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM Encoder Interface MSP. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_Encoder_MspDeInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_Encoder_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM Encoder Interface. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Start(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Enable the encoder interface channels */ switch (Channel) { case TIM_CHANNEL_1: { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); break; } case TIM_CHANNEL_2: { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); break; } default : { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); break; } } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Encoder Interface. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be disabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Disable the Input Capture channels 1 and 2 (in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */ switch (Channel) { case TIM_CHANNEL_1: { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); break; } case TIM_CHANNEL_2: { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); break; } default : { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); break; } } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Encoder Interface in interrupt mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Enable the encoder interface channels */ /* Enable the capture compare Interrupts 1 and/or 2 */ switch (Channel) { case TIM_CHANNEL_1: { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); break; } case TIM_CHANNEL_2: { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); break; } default : { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); break; } } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Encoder Interface in interrupt mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be disabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Disable the Input Capture channels 1 and 2 (in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */ if(Channel == TIM_CHANNEL_1) { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); /* Disable the capture compare Interrupts 1 */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); } else if(Channel == TIM_CHANNEL_2) { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); /* Disable the capture compare Interrupts 2 */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); } else { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); /* Disable the capture compare Interrupts 1 and 2 */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Encoder Interface in DMA mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected * @param pData1 The destination Buffer address for IC1. * @param pData2 The destination Buffer address for IC2. * @param Length The length of data to be transferred from TIM peripheral to memory. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData1, uint32_t *pData2, uint16_t Length) { /* Check the parameters */ assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if((((pData1 == 0U) || (pData2 == 0U) )) && (Length > 0)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } switch (Channel) { case TIM_CHANNEL_1: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t )pData1, Length); /* Enable the TIM Input Capture DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); } break; case TIM_CHANNEL_2: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData2, Length); /* Enable the TIM Input Capture DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); } break; case TIM_CHANNEL_ALL: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData1, Length); /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData2, Length); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); /* Enable the TIM Input Capture DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); /* Enable the TIM Input Capture DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); } break; default: break; } /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Encoder Interface in DMA mode. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance)); /* Disable the Input Capture channels 1 and 2 (in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */ if(Channel == TIM_CHANNEL_1) { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); /* Disable the capture compare DMA Request 1 */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); } else if(Channel == TIM_CHANNEL_2) { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); /* Disable the capture compare DMA Request 2 */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); } else { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); /* Disable the capture compare DMA Request 1 and 2 */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group7 TIM IRQ handler management * @brief IRQ handler management * @verbatim ============================================================================== ##### IRQ handler management ##### ============================================================================== [..] This section provides Timer IRQ handler function. @endverbatim * @{ */ /** * @brief This function handles TIM interrupts requests. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ void HAL_TIM_IRQHandler(TIM_HandleTypeDef *htim) { /* Capture compare 1 event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC1) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_CC1) !=RESET) { { __HAL_TIM_CLEAR_IT(htim, TIM_IT_CC1); htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1; /* Input capture event */ if((htim->Instance->CCMR1 & TIM_CCMR1_CC1S) != 0x00U) { HAL_TIM_IC_CaptureCallback(htim); } /* Output compare event */ else { HAL_TIM_OC_DelayElapsedCallback(htim); HAL_TIM_PWM_PulseFinishedCallback(htim); } htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } } } /* Capture compare 2 event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC2) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_CC2) !=RESET) { __HAL_TIM_CLEAR_IT(htim, TIM_IT_CC2); htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2; /* Input capture event */ if((htim->Instance->CCMR1 & TIM_CCMR1_CC2S) != 0x00U) { HAL_TIM_IC_CaptureCallback(htim); } /* Output compare event */ else { HAL_TIM_OC_DelayElapsedCallback(htim); HAL_TIM_PWM_PulseFinishedCallback(htim); } htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } } /* Capture compare 3 event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC3) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_CC3) !=RESET) { __HAL_TIM_CLEAR_IT(htim, TIM_IT_CC3); htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3; /* Input capture event */ if((htim->Instance->CCMR2 & TIM_CCMR2_CC3S) != 0x00U) { HAL_TIM_IC_CaptureCallback(htim); } /* Output compare event */ else { HAL_TIM_OC_DelayElapsedCallback(htim); HAL_TIM_PWM_PulseFinishedCallback(htim); } htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } } /* Capture compare 4 event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC4) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_CC4) !=RESET) { __HAL_TIM_CLEAR_IT(htim, TIM_IT_CC4); htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4; /* Input capture event */ if((htim->Instance->CCMR2 & TIM_CCMR2_CC4S) != 0x00U) { HAL_TIM_IC_CaptureCallback(htim); } /* Output compare event */ else { HAL_TIM_OC_DelayElapsedCallback(htim); HAL_TIM_PWM_PulseFinishedCallback(htim); } htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } } /* TIM Update event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_UPDATE) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_UPDATE) !=RESET) { __HAL_TIM_CLEAR_IT(htim, TIM_IT_UPDATE); HAL_TIM_PeriodElapsedCallback(htim); } } /* TIM Break input event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_BREAK) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_BREAK) !=RESET) { __HAL_TIM_CLEAR_IT(htim, TIM_IT_BREAK); HAL_TIMEx_BreakCallback(htim); } } /* TIM Trigger detection event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_TRIGGER) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_TRIGGER) !=RESET) { __HAL_TIM_CLEAR_IT(htim, TIM_IT_TRIGGER); HAL_TIM_TriggerCallback(htim); } } /* TIM commutation event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_COM) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_COM) !=RESET) { __HAL_TIM_CLEAR_IT(htim, TIM_FLAG_COM); HAL_TIMEx_CommutationCallback(htim); } } } /** * @} */ /** @defgroup TIM_Exported_Functions_Group8 Peripheral Control functions * @brief Peripheral Control functions * @verbatim ============================================================================== ##### Peripheral Control functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Configure The Input Output channels for OC, PWM, IC or One Pulse mode. (+) Configure External Clock source. (+) Configure Complementary channels, break features and dead time. (+) Configure Master and the Slave synchronization. (+) Configure the DMA Burst Mode. @endverbatim * @{ */ /** * @brief Initializes the TIM Output Compare Channels according to the specified * parameters in the TIM_OC_InitTypeDef. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param sConfig TIM Output Compare configuration structure * @param Channel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_ConfigChannel(TIM_HandleTypeDef *htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CHANNELS(Channel)); assert_param(IS_TIM_OC_MODE(sConfig->OCMode)); assert_param(IS_TIM_OC_POLARITY(sConfig->OCPolarity)); /* Check input state */ __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; switch (Channel) { case TIM_CHANNEL_1: { assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); /* Configure the TIM Channel 1 in Output Compare */ TIM_OC1_SetConfig(htim->Instance, sConfig); } break; case TIM_CHANNEL_2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Configure the TIM Channel 2 in Output Compare */ TIM_OC2_SetConfig(htim->Instance, sConfig); } break; case TIM_CHANNEL_3: { assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); /* Configure the TIM Channel 3 in Output Compare */ TIM_OC3_SetConfig(htim->Instance, sConfig); } break; case TIM_CHANNEL_4: { assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); /* Configure the TIM Channel 4 in Output Compare */ TIM_OC4_SetConfig(htim->Instance, sConfig); } break; default: break; } htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM Input Capture Channels according to the specified * parameters in the TIM_IC_InitTypeDef. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param sConfig TIM Input Capture configuration structure * @param Channel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_ConfigChannel(TIM_HandleTypeDef *htim, TIM_IC_InitTypeDef* sConfig, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); assert_param(IS_TIM_IC_POLARITY(sConfig->ICPolarity)); assert_param(IS_TIM_IC_SELECTION(sConfig->ICSelection)); assert_param(IS_TIM_IC_PRESCALER(sConfig->ICPrescaler)); assert_param(IS_TIM_IC_FILTER(sConfig->ICFilter)); __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; if (Channel == TIM_CHANNEL_1) { /* TI1 Configuration */ TIM_TI1_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); /* Reset the IC1PSC Bits */ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC; /* Set the IC1PSC value */ htim->Instance->CCMR1 |= sConfig->ICPrescaler; } else if (Channel == TIM_CHANNEL_2) { /* TI2 Configuration */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); TIM_TI2_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); /* Reset the IC2PSC Bits */ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC2PSC; /* Set the IC2PSC value */ htim->Instance->CCMR1 |= (sConfig->ICPrescaler << 8U); } else if (Channel == TIM_CHANNEL_3) { /* TI3 Configuration */ assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); TIM_TI3_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); /* Reset the IC3PSC Bits */ htim->Instance->CCMR2 &= ~TIM_CCMR2_IC3PSC; /* Set the IC3PSC value */ htim->Instance->CCMR2 |= sConfig->ICPrescaler; } else { /* TI4 Configuration */ assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); TIM_TI4_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); /* Reset the IC4PSC Bits */ htim->Instance->CCMR2 &= ~TIM_CCMR2_IC4PSC; /* Set the IC4PSC value */ htim->Instance->CCMR2 |= (sConfig->ICPrescaler << 8U); } htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM PWM channels according to the specified * parameters in the TIM_OC_InitTypeDef. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param sConfig TIM PWM configuration structure * @param Channel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_ConfigChannel(TIM_HandleTypeDef *htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel) { __HAL_LOCK(htim); /* Check the parameters */ assert_param(IS_TIM_CHANNELS(Channel)); assert_param(IS_TIM_PWM_MODE(sConfig->OCMode)); assert_param(IS_TIM_OC_POLARITY(sConfig->OCPolarity)); assert_param(IS_TIM_FAST_STATE(sConfig->OCFastMode)); htim->State = HAL_TIM_STATE_BUSY; switch (Channel) { case TIM_CHANNEL_1: { assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); /* Configure the Channel 1 in PWM mode */ TIM_OC1_SetConfig(htim->Instance, sConfig); /* Set the Preload enable bit for channel1 */ htim->Instance->CCMR1 |= TIM_CCMR1_OC1PE; /* Configure the Output Fast mode */ htim->Instance->CCMR1 &= ~TIM_CCMR1_OC1FE; htim->Instance->CCMR1 |= sConfig->OCFastMode; } break; case TIM_CHANNEL_2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Configure the Channel 2 in PWM mode */ TIM_OC2_SetConfig(htim->Instance, sConfig); /* Set the Preload enable bit for channel2 */ htim->Instance->CCMR1 |= TIM_CCMR1_OC2PE; /* Configure the Output Fast mode */ htim->Instance->CCMR1 &= ~TIM_CCMR1_OC2FE; htim->Instance->CCMR1 |= sConfig->OCFastMode << 8U; } break; case TIM_CHANNEL_3: { assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); /* Configure the Channel 3 in PWM mode */ TIM_OC3_SetConfig(htim->Instance, sConfig); /* Set the Preload enable bit for channel3 */ htim->Instance->CCMR2 |= TIM_CCMR2_OC3PE; /* Configure the Output Fast mode */ htim->Instance->CCMR2 &= ~TIM_CCMR2_OC3FE; htim->Instance->CCMR2 |= sConfig->OCFastMode; } break; case TIM_CHANNEL_4: { assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); /* Configure the Channel 4 in PWM mode */ TIM_OC4_SetConfig(htim->Instance, sConfig); /* Set the Preload enable bit for channel4 */ htim->Instance->CCMR2 |= TIM_CCMR2_OC4PE; /* Configure the Output Fast mode */ htim->Instance->CCMR2 &= ~TIM_CCMR2_OC4FE; htim->Instance->CCMR2 |= sConfig->OCFastMode << 8U; } break; default: break; } htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM One Pulse Channels according to the specified * parameters in the TIM_OnePulse_InitTypeDef. * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param sConfig TIM One Pulse configuration structure * @param OutputChannel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @param InputChannel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel(TIM_HandleTypeDef *htim, TIM_OnePulse_InitTypeDef* sConfig, uint32_t OutputChannel, uint32_t InputChannel) { TIM_OC_InitTypeDef temp1; /* Check the parameters */ assert_param(IS_TIM_OPM_CHANNELS(OutputChannel)); assert_param(IS_TIM_OPM_CHANNELS(InputChannel)); if(OutputChannel != InputChannel) { __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; /* Extract the Output compare configuration from sConfig structure */ temp1.OCMode = sConfig->OCMode; temp1.Pulse = sConfig->Pulse; temp1.OCPolarity = sConfig->OCPolarity; temp1.OCNPolarity = sConfig->OCNPolarity; temp1.OCIdleState = sConfig->OCIdleState; temp1.OCNIdleState = sConfig->OCNIdleState; switch (OutputChannel) { case TIM_CHANNEL_1: { assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); TIM_OC1_SetConfig(htim->Instance, &temp1); } break; case TIM_CHANNEL_2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); TIM_OC2_SetConfig(htim->Instance, &temp1); } break; default: break; } switch (InputChannel) { case TIM_CHANNEL_1: { assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); TIM_TI1_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); /* Reset the IC1PSC Bits */ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC; /* Select the Trigger source */ htim->Instance->SMCR &= ~TIM_SMCR_TS; htim->Instance->SMCR |= TIM_TS_TI1FP1; /* Select the Slave Mode */ htim->Instance->SMCR &= ~TIM_SMCR_SMS; htim->Instance->SMCR |= TIM_SLAVEMODE_TRIGGER; } break; case TIM_CHANNEL_2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); TIM_TI2_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); /* Reset the IC2PSC Bits */ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC2PSC; /* Select the Trigger source */ htim->Instance->SMCR &= ~TIM_SMCR_TS; htim->Instance->SMCR |= TIM_TS_TI2FP2; /* Select the Slave Mode */ htim->Instance->SMCR &= ~TIM_SMCR_SMS; htim->Instance->SMCR |= TIM_SLAVEMODE_TRIGGER; } break; default: break; } htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } else { return HAL_ERROR; } } /** * @brief Configure the DMA Burst to transfer Data from the memory to the TIM peripheral * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param BurstBaseAddress TIM Base address from when the DMA will starts the Data write. * This parameters can be on of the following values: * @arg TIM_DMABASE_CR1 * @arg TIM_DMABASE_CR2 * @arg TIM_DMABASE_SMCR * @arg TIM_DMABASE_DIER * @arg TIM_DMABASE_SR * @arg TIM_DMABASE_EGR * @arg TIM_DMABASE_CCMR1 * @arg TIM_DMABASE_CCMR2 * @arg TIM_DMABASE_CCER * @arg TIM_DMABASE_CNT * @arg TIM_DMABASE_PSC * @arg TIM_DMABASE_ARR * @arg TIM_DMABASE_RCR * @arg TIM_DMABASE_CCR1 * @arg TIM_DMABASE_CCR2 * @arg TIM_DMABASE_CCR3 * @arg TIM_DMABASE_CCR4 * @arg TIM_DMABASE_BDTR * @arg TIM_DMABASE_DCR * @param BurstRequestSrc TIM DMA Request sources. * This parameters can be on of the following values: * @arg TIM_DMA_UPDATE: TIM update Interrupt source * @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source * @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source * @arg TIM_DMA_CC3: TIM Capture Compare 3 DMA source * @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source * @arg TIM_DMA_COM: TIM Commutation DMA source * @arg TIM_DMA_TRIGGER: TIM Trigger DMA source * @param BurstBuffer The Buffer address. * @param BurstLength DMA Burst length. This parameter can be one value * between TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStart(TIM_HandleTypeDef *htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc, uint32_t* BurstBuffer, uint32_t BurstLength) { /* Check the parameters */ assert_param(IS_TIM_DMABURST_INSTANCE(htim->Instance)); assert_param(IS_TIM_DMA_BASE(BurstBaseAddress)); assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc)); assert_param(IS_TIM_DMA_LENGTH(BurstLength)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if((BurstBuffer == 0U) && (BurstLength > 0U)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } switch(BurstRequestSrc) { case TIM_DMA_UPDATE: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); } break; case TIM_DMA_CC1: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); } break; case TIM_DMA_CC2: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); } break; case TIM_DMA_CC3: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); } break; case TIM_DMA_CC4: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); } break; case TIM_DMA_COM: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferCpltCallback = TIMEx_DMACommutationCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_COMMUTATION], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); } break; case TIM_DMA_TRIGGER: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_TRIGGER]->XferCpltCallback = TIM_DMATriggerCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_TRIGGER]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_TRIGGER], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, ((BurstLength) >> 8U) + 1U); } break; default: break; } /* configure the DMA Burst Mode */ htim->Instance->DCR = BurstBaseAddress | BurstLength; /* Enable the TIM DMA Request */ __HAL_TIM_ENABLE_DMA(htim, BurstRequestSrc); htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM DMA Burst mode * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param BurstRequestSrc TIM DMA Request sources to disable * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStop(TIM_HandleTypeDef *htim, uint32_t BurstRequestSrc) { /* Check the parameters */ assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc)); /* Abort the DMA transfer (at least disable the DMA channel) */ switch(BurstRequestSrc) { case TIM_DMA_UPDATE: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_UPDATE]); } break; case TIM_DMA_CC1: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC1]); } break; case TIM_DMA_CC2: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC2]); } break; case TIM_DMA_CC3: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC3]); } break; case TIM_DMA_CC4: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC4]); } break; case TIM_DMA_COM: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_COMMUTATION]); } break; case TIM_DMA_TRIGGER: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_TRIGGER]); } break; default: break; } /* Disable the TIM Update DMA request */ __HAL_TIM_DISABLE_DMA(htim, BurstRequestSrc); /* Return function status */ return HAL_OK; } /** * @brief Configure the DMA Burst to transfer Data from the TIM peripheral to the memory * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param BurstBaseAddress TIM Base address from when the DMA will starts the Data read. * This parameters can be on of the following values: * @arg TIM_DMABASE_CR1 * @arg TIM_DMABASE_CR2 * @arg TIM_DMABASE_SMCR * @arg TIM_DMABASE_DIER * @arg TIM_DMABASE_SR * @arg TIM_DMABASE_EGR * @arg TIM_DMABASE_CCMR1 * @arg TIM_DMABASE_CCMR2 * @arg TIM_DMABASE_CCER * @arg TIM_DMABASE_CNT * @arg TIM_DMABASE_PSC * @arg TIM_DMABASE_ARR * @arg TIM_DMABASE_RCR * @arg TIM_DMABASE_CCR1 * @arg TIM_DMABASE_CCR2 * @arg TIM_DMABASE_CCR3 * @arg TIM_DMABASE_CCR4 * @arg TIM_DMABASE_BDTR * @arg TIM_DMABASE_DCR * @param BurstRequestSrc TIM DMA Request sources. * This parameters can be on of the following values: * @arg TIM_DMA_UPDATE: TIM update Interrupt source * @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source * @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source * @arg TIM_DMA_CC3: TIM Capture Compare 3 DMA source * @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source * @arg TIM_DMA_COM: TIM Commutation DMA source * @arg TIM_DMA_TRIGGER: TIM Trigger DMA source * @param BurstBuffer The Buffer address. * @param BurstLength DMA Burst length. This parameter can be one value * between TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStart(TIM_HandleTypeDef *htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc, uint32_t *BurstBuffer, uint32_t BurstLength) { /* Check the parameters */ assert_param(IS_TIM_DMABURST_INSTANCE(htim->Instance)); assert_param(IS_TIM_DMA_BASE(BurstBaseAddress)); assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc)); assert_param(IS_TIM_DMA_LENGTH(BurstLength)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if((BurstBuffer == 0U) && (BurstLength > 0U)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } switch(BurstRequestSrc) { case TIM_DMA_UPDATE: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U); } break; case TIM_DMA_CC1: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U); } break; case TIM_DMA_CC2: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U); } break; case TIM_DMA_CC3: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U); } break; case TIM_DMA_CC4: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U); } break; case TIM_DMA_COM: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferCpltCallback = TIMEx_DMACommutationCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_COMMUTATION], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1U); } break; case TIM_DMA_TRIGGER: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_TRIGGER]->XferCpltCallback = TIM_DMATriggerCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_TRIGGER]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA Stream */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_TRIGGER], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, ((BurstLength) >> 8U) + 1); } break; default: break; } /* configure the DMA Burst Mode */ htim->Instance->DCR = BurstBaseAddress | BurstLength; /* Enable the TIM DMA Request */ __HAL_TIM_ENABLE_DMA(htim, BurstRequestSrc); htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the DMA burst reading * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param BurstRequestSrc TIM DMA Request sources to disable. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStop(TIM_HandleTypeDef *htim, uint32_t BurstRequestSrc) { /* Check the parameters */ assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc)); /* Abort the DMA transfer (at least disable the DMA channel) */ switch(BurstRequestSrc) { case TIM_DMA_UPDATE: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_UPDATE]); } break; case TIM_DMA_CC1: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC1]); } break; case TIM_DMA_CC2: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC2]); } break; case TIM_DMA_CC3: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC3]); } break; case TIM_DMA_CC4: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC4]); } break; case TIM_DMA_COM: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_COMMUTATION]); } break; case TIM_DMA_TRIGGER: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_TRIGGER]); } break; default: break; } /* Disable the TIM Update DMA request */ __HAL_TIM_DISABLE_DMA(htim, BurstRequestSrc); /* Return function status */ return HAL_OK; } /** * @brief Generate a software event * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param EventSource specifies the event source. * This parameter can be one of the following values: * @arg TIM_EVENTSOURCE_UPDATE: Timer update Event source * @arg TIM_EVENTSOURCE_CC1: Timer Capture Compare 1 Event source * @arg TIM_EVENTSOURCE_CC2: Timer Capture Compare 2 Event source * @arg TIM_EVENTSOURCE_CC3: Timer Capture Compare 3 Event source * @arg TIM_EVENTSOURCE_CC4: Timer Capture Compare 4 Event source * @arg TIM_EVENTSOURCE_COM: Timer COM event source * @arg TIM_EVENTSOURCE_TRIGGER: Timer Trigger Event source * @arg TIM_EVENTSOURCE_BREAK: Timer Break event source * @note TIM6 and TIM7 can only generate an update event. * @note TIM_EVENTSOURCE_COM and TIM_EVENTSOURCE_BREAK are used only with TIM1 and TIM8. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_GenerateEvent(TIM_HandleTypeDef *htim, uint32_t EventSource) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_EVENT_SOURCE(EventSource)); /* Process Locked */ __HAL_LOCK(htim); /* Change the TIM state */ htim->State = HAL_TIM_STATE_BUSY; /* Set the event sources */ htim->Instance->EGR = EventSource; /* Change the TIM state */ htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); /* Return function status */ return HAL_OK; } /** * @brief Configures the OCRef clear feature * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param sClearInputConfig pointer to a TIM_ClearInputConfigTypeDef structure that * contains the OCREF clear feature and parameters for the TIM peripheral. * @param Channel specifies the TIM Channel. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_ConfigOCrefClear(TIM_HandleTypeDef *htim, TIM_ClearInputConfigTypeDef * sClearInputConfig, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); assert_param(IS_TIM_CHANNELS(Channel)); assert_param(IS_TIM_CLEARINPUT_SOURCE(sClearInputConfig->ClearInputSource)); assert_param(IS_TIM_CLEARINPUT_POLARITY(sClearInputConfig->ClearInputPolarity)); assert_param(IS_TIM_CLEARINPUT_PRESCALER(sClearInputConfig->ClearInputPrescaler)); assert_param(IS_TIM_CLEARINPUT_FILTER(sClearInputConfig->ClearInputFilter)); /* Process Locked */ __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; if(sClearInputConfig->ClearInputSource == TIM_CLEARINPUTSOURCE_ETR) { TIM_ETR_SetConfig(htim->Instance, sClearInputConfig->ClearInputPrescaler, sClearInputConfig->ClearInputPolarity, sClearInputConfig->ClearInputFilter); } switch (Channel) { case TIM_CHANNEL_1: { if(sClearInputConfig->ClearInputState != RESET) { /* Enable the Ocref clear feature for Channel 1 */ htim->Instance->CCMR1 |= TIM_CCMR1_OC1CE; } else { /* Disable the Ocref clear feature for Channel 1 */ htim->Instance->CCMR1 &= ~TIM_CCMR1_OC1CE; } } break; case TIM_CHANNEL_2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); if(sClearInputConfig->ClearInputState != RESET) { /* Enable the Ocref clear feature for Channel 2 */ htim->Instance->CCMR1 |= TIM_CCMR1_OC2CE; } else { /* Disable the Ocref clear feature for Channel 2 */ htim->Instance->CCMR1 &= ~TIM_CCMR1_OC2CE; } } break; case TIM_CHANNEL_3: { assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); if(sClearInputConfig->ClearInputState != RESET) { /* Enable the Ocref clear feature for Channel 3 */ htim->Instance->CCMR2 |= TIM_CCMR2_OC3CE; } else { /* Disable the Ocref clear feature for Channel 3 */ htim->Instance->CCMR2 &= ~TIM_CCMR2_OC3CE; } } break; case TIM_CHANNEL_4: { assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); if(sClearInputConfig->ClearInputState != RESET) { /* Enable the Ocref clear feature for Channel 4 */ htim->Instance->CCMR2 |= TIM_CCMR2_OC4CE; } else { /* Disable the Ocref clear feature for Channel 4 */ htim->Instance->CCMR2 &= ~TIM_CCMR2_OC4CE; } } break; default: break; } htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Configures the clock source to be used * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param sClockSourceConfig pointer to a TIM_ClockConfigTypeDef structure that * contains the clock source information for the TIM peripheral. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_ConfigClockSource(TIM_HandleTypeDef *htim, TIM_ClockConfigTypeDef * sClockSourceConfig) { uint32_t tmpsmcr = 0U; /* Process Locked */ __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; /* Check the parameters */ assert_param(IS_TIM_CLOCKSOURCE(sClockSourceConfig->ClockSource)); /* Reset the SMS, TS, ECE, ETPS and ETRF bits */ tmpsmcr = htim->Instance->SMCR; tmpsmcr &= ~(TIM_SMCR_SMS | TIM_SMCR_TS); tmpsmcr &= ~(TIM_SMCR_ETF | TIM_SMCR_ETPS | TIM_SMCR_ECE | TIM_SMCR_ETP); htim->Instance->SMCR = tmpsmcr; switch (sClockSourceConfig->ClockSource) { case TIM_CLOCKSOURCE_INTERNAL: { assert_param(IS_TIM_INSTANCE(htim->Instance)); /* Disable slave mode to clock the prescaler directly with the internal clock */ htim->Instance->SMCR &= ~TIM_SMCR_SMS; } break; case TIM_CLOCKSOURCE_ETRMODE1: { assert_param(IS_TIM_ETR_INSTANCE(htim->Instance)); assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKPRESCALER(sClockSourceConfig->ClockPrescaler)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); /* Configure the ETR Clock source */ TIM_ETR_SetConfig(htim->Instance, sClockSourceConfig->ClockPrescaler, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); /* Get the TIMx SMCR register value */ tmpsmcr = htim->Instance->SMCR; /* Reset the SMS and TS Bits */ tmpsmcr &= ~(TIM_SMCR_SMS | TIM_SMCR_TS); /* Select the External clock mode1 and the ETRF trigger */ tmpsmcr |= (TIM_SLAVEMODE_EXTERNAL1 | TIM_CLOCKSOURCE_ETRMODE1); /* Write to TIMx SMCR */ htim->Instance->SMCR = tmpsmcr; } break; case TIM_CLOCKSOURCE_ETRMODE2: { assert_param(IS_TIM_ETR_INSTANCE(htim->Instance)); assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKPRESCALER(sClockSourceConfig->ClockPrescaler)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); /* Configure the ETR Clock source */ TIM_ETR_SetConfig(htim->Instance, sClockSourceConfig->ClockPrescaler, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); /* Enable the External clock mode2 */ htim->Instance->SMCR |= TIM_SMCR_ECE; } break; case TIM_CLOCKSOURCE_TI1: { assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); /* Check TI1 input conditioning related parameters */ assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); TIM_TI1_ConfigInputStage(htim->Instance, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI1); } break; case TIM_CLOCKSOURCE_TI2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Check TI1 input conditioning related parameters */ assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); TIM_TI2_ConfigInputStage(htim->Instance, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI2); } break; case TIM_CLOCKSOURCE_TI1ED: { assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); /* Check TI1 input conditioning related parameters */ assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); TIM_TI1_ConfigInputStage(htim->Instance, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI1ED); } break; case TIM_CLOCKSOURCE_ITR0: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR0); } break; case TIM_CLOCKSOURCE_ITR1: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR1); } break; case TIM_CLOCKSOURCE_ITR2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR2); } break; case TIM_CLOCKSOURCE_ITR3: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR3); } break; default: break; } htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Selects the signal connected to the TI1 input: direct from CH1_input * or a XOR combination between CH1_input, CH2_input & CH3_input * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param TI1_Selection Indicate whether or not channel 1 is connected to the * output of a XOR gate. * This parameter can be one of the following values: * @arg TIM_TI1SELECTION_CH1: The TIMx_CH1 pin is connected to TI1 input * @arg TIM_TI1SELECTION_XORCOMBINATION: The TIMx_CH1, CH2 and CH3 * pins are connected to the TI1 input (XOR combination) * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_ConfigTI1Input(TIM_HandleTypeDef *htim, uint32_t TI1_Selection) { uint32_t tmpcr2 = 0U; /* Check the parameters */ assert_param(IS_TIM_XOR_INSTANCE(htim->Instance)); assert_param(IS_TIM_TI1SELECTION(TI1_Selection)); /* Get the TIMx CR2 register value */ tmpcr2 = htim->Instance->CR2; /* Reset the TI1 selection */ tmpcr2 &= ~TIM_CR2_TI1S; /* Set the TI1 selection */ tmpcr2 |= TI1_Selection; /* Write to TIMxCR2 */ htim->Instance->CR2 = tmpcr2; return HAL_OK; } /** * @brief Configures the TIM in Slave mode * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param sSlaveConfig pointer to a TIM_SlaveConfigTypeDef structure that * contains the selected trigger (internal trigger input, filtered * timer input or external trigger input) and the ) and the Slave * mode (Disable, Reset, Gated, Trigger, External clock mode 1). * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization(TIM_HandleTypeDef *htim, TIM_SlaveConfigTypeDef * sSlaveConfig) { /* Check the parameters */ assert_param(IS_TIM_SLAVE_INSTANCE(htim->Instance)); assert_param(IS_TIM_SLAVE_MODE(sSlaveConfig->SlaveMode)); assert_param(IS_TIM_TRIGGER_SELECTION(sSlaveConfig->InputTrigger)); __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; TIM_SlaveTimer_SetConfig(htim, sSlaveConfig); /* Disable Trigger Interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_TRIGGER); /* Disable Trigger DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_TRIGGER); htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Configures the TIM in Slave mode in interrupt mode * @param htim TIM handle. * @param sSlaveConfig pointer to a TIM_SlaveConfigTypeDef structure that * contains the selected trigger (internal trigger input, filtered * timer input or external trigger input) and the ) and the Slave * mode (Disable, Reset, Gated, Trigger, External clock mode 1). * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization_IT(TIM_HandleTypeDef *htim, TIM_SlaveConfigTypeDef * sSlaveConfig) { /* Check the parameters */ assert_param(IS_TIM_SLAVE_INSTANCE(htim->Instance)); assert_param(IS_TIM_SLAVE_MODE(sSlaveConfig->SlaveMode)); assert_param(IS_TIM_TRIGGER_SELECTION(sSlaveConfig->InputTrigger)); __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; TIM_SlaveTimer_SetConfig(htim, sSlaveConfig); /* Enable Trigger Interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_TRIGGER); /* Disable Trigger DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_TRIGGER); htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Read the captured value from Capture Compare unit * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param Channel TIM Channels to be enabled. * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval Captured value */ uint32_t HAL_TIM_ReadCapturedValue(TIM_HandleTypeDef *htim, uint32_t Channel) { uint32_t tmpreg = 0U; __HAL_LOCK(htim); switch (Channel) { case TIM_CHANNEL_1: { /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); /* Return the capture 1 value */ tmpreg = htim->Instance->CCR1; break; } case TIM_CHANNEL_2: { /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Return the capture 2 value */ tmpreg = htim->Instance->CCR2; break; } case TIM_CHANNEL_3: { /* Check the parameters */ assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); /* Return the capture 3 value */ tmpreg = htim->Instance->CCR3; break; } case TIM_CHANNEL_4: { /* Check the parameters */ assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); /* Return the capture 4 value */ tmpreg = htim->Instance->CCR4; break; } default: break; } __HAL_UNLOCK(htim); return tmpreg; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group9 TIM Callbacks functions * @brief TIM Callbacks functions * @verbatim ============================================================================== ##### TIM Callbacks functions ##### ============================================================================== [..] This section provides TIM callback functions: (+) Timer Period elapsed callback (+) Timer Output Compare callback (+) Timer Input capture callback (+) Timer Trigger callback (+) Timer Error callback @endverbatim * @{ */ /** * @brief Period elapsed callback in non blocking mode * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the __HAL_TIM_PeriodElapsedCallback could be implemented in the user file */ } /** * @brief Output Compare callback in non blocking mode * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_OC_DelayElapsedCallback(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the __HAL_TIM_OC_DelayElapsedCallback could be implemented in the user file */ } /** * @brief Input Capture callback in non blocking mode * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_IC_CaptureCallback(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the __HAL_TIM_IC_CaptureCallback could be implemented in the user file */ } /** * @brief PWM Pulse finished callback in non blocking mode * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_PWM_PulseFinishedCallback(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the __HAL_TIM_PWM_PulseFinishedCallback could be implemented in the user file */ } /** * @brief Hall Trigger detection callback in non blocking mode * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_TriggerCallback(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_TriggerCallback could be implemented in the user file */ } /** * @brief Timer error callback in non blocking mode * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval None */ __weak void HAL_TIM_ErrorCallback(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_ErrorCallback could be implemented in the user file */ } /** * @} */ /** @defgroup TIM_Exported_Functions_Group10 Peripheral State functions * @brief Peripheral State functions * @verbatim ============================================================================== ##### Peripheral State functions ##### ============================================================================== [..] This subsection permits to get in run-time the status of the peripheral and the data flow. @endverbatim * @{ */ /** * @brief Return the TIM Base state * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL state */ HAL_TIM_StateTypeDef HAL_TIM_Base_GetState(TIM_HandleTypeDef *htim) { return htim->State; } /** * @brief Return the TIM OC state * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL state */ HAL_TIM_StateTypeDef HAL_TIM_OC_GetState(TIM_HandleTypeDef *htim) { return htim->State; } /** * @brief Return the TIM PWM state * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL state */ HAL_TIM_StateTypeDef HAL_TIM_PWM_GetState(TIM_HandleTypeDef *htim) { return htim->State; } /** * @brief Return the TIM Input Capture state * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL state */ HAL_TIM_StateTypeDef HAL_TIM_IC_GetState(TIM_HandleTypeDef *htim) { return htim->State; } /** * @brief Return the TIM One Pulse Mode state * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL state */ HAL_TIM_StateTypeDef HAL_TIM_OnePulse_GetState(TIM_HandleTypeDef *htim) { return htim->State; } /** * @brief Return the TIM Encoder Mode state * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @retval HAL state */ HAL_TIM_StateTypeDef HAL_TIM_Encoder_GetState(TIM_HandleTypeDef *htim) { return htim->State; } /** * @} */ /** * @brief Time Base configuration * @param TIMx TIM peripheral * @param Structure pointer on TIM Time Base required parameters * @retval None */ void TIM_Base_SetConfig(TIM_TypeDef *TIMx, TIM_Base_InitTypeDef *Structure) { uint32_t tmpcr1 = 0U; tmpcr1 = TIMx->CR1; /* Set TIM Time Base Unit parameters ---------------------------------------*/ if(IS_TIM_CC3_INSTANCE(TIMx) != RESET) { /* Select the Counter Mode */ tmpcr1 &= ~(TIM_CR1_DIR | TIM_CR1_CMS); tmpcr1 |= Structure->CounterMode; } if(IS_TIM_CC1_INSTANCE(TIMx) != RESET) { /* Set the clock division */ tmpcr1 &= ~TIM_CR1_CKD; tmpcr1 |= (uint32_t)Structure->ClockDivision; } TIMx->CR1 = tmpcr1; /* Set the Auto-reload value */ TIMx->ARR = (uint32_t)Structure->Period ; /* Set the Prescaler value */ TIMx->PSC = (uint32_t)Structure->Prescaler; if(IS_TIM_ADVANCED_INSTANCE(TIMx) != RESET) { /* Set the Repetition Counter value */ TIMx->RCR = Structure->RepetitionCounter; } /* Generate an update event to reload the Prescaler and the repetition counter(only for TIM1 and TIM8) value immediately */ TIMx->EGR = TIM_EGR_UG; } /** * @brief Configure the TI1 as Input. * @param TIMx to select the TIM peripheral. * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_ICPolarity_Rising * @arg TIM_ICPolarity_Falling * @arg TIM_ICPolarity_BothEdge * @param TIM_ICSelection specifies the input to be used. * This parameter can be one of the following values: * @arg TIM_ICSelection_DirectTI: TIM Input 1 is selected to be connected to IC1. * @arg TIM_ICSelection_IndirectTI: TIM Input 1 is selected to be connected to IC2. * @arg TIM_ICSelection_TRC: TIM Input 1 is selected to be connected to TRC. * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI2FP1 * (on channel2 path) is used as the input signal. Therefore CCMR1 must be * protected against un-initialized filter and polarity values. * @retval None */ void TIM_TI1_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter) { uint32_t tmpccmr1 = 0U; uint32_t tmpccer = 0U; /* Disable the Channel 1: Reset the CC1E Bit */ TIMx->CCER &= ~TIM_CCER_CC1E; tmpccmr1 = TIMx->CCMR1; tmpccer = TIMx->CCER; /* Select the Input */ if(IS_TIM_CC2_INSTANCE(TIMx) != RESET) { tmpccmr1 &= ~TIM_CCMR1_CC1S; tmpccmr1 |= TIM_ICSelection; } else { tmpccmr1 &= ~TIM_CCMR1_CC1S; tmpccmr1 |= TIM_CCMR1_CC1S_0; } /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC1F; tmpccmr1 |= ((TIM_ICFilter << 4U) & TIM_CCMR1_IC1F); /* Select the Polarity and set the CC1E Bit */ tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC1NP); tmpccer |= (TIM_ICPolarity & (TIM_CCER_CC1P | TIM_CCER_CC1NP)); /* Write to TIMx CCMR1 and CCER registers */ TIMx->CCMR1 = tmpccmr1; TIMx->CCER = tmpccer; } /** * @brief Time Output Compare 2 configuration * @param TIMx to select the TIM peripheral * @param OC_Config The output configuration structure * @retval None */ void TIM_OC2_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config) { uint32_t tmpccmrx = 0U; uint32_t tmpccer = 0U; uint32_t tmpcr2 = 0U; /* Disable the Channel 2: Reset the CC2E Bit */ TIMx->CCER &= ~TIM_CCER_CC2E; /* Get the TIMx CCER register value */ tmpccer = TIMx->CCER; /* Get the TIMx CR2 register value */ tmpcr2 = TIMx->CR2; /* Get the TIMx CCMR1 register value */ tmpccmrx = TIMx->CCMR1; /* Reset the Output Compare mode and Capture/Compare selection Bits */ tmpccmrx &= ~TIM_CCMR1_OC2M; tmpccmrx &= ~TIM_CCMR1_CC2S; /* Select the Output Compare Mode */ tmpccmrx |= (OC_Config->OCMode << 8U); /* Reset the Output Polarity level */ tmpccer &= ~TIM_CCER_CC2P; /* Set the Output Compare Polarity */ tmpccer |= (OC_Config->OCPolarity << 4U); if(IS_TIM_ADVANCED_INSTANCE(TIMx) != RESET) { assert_param(IS_TIM_OCN_POLARITY(OC_Config->OCNPolarity)); /* Reset the Output N Polarity level */ tmpccer &= ~TIM_CCER_CC2NP; /* Set the Output N Polarity */ tmpccer |= (OC_Config->OCNPolarity << 4U); /* Reset the Output N State */ tmpccer &= ~TIM_CCER_CC2NE; /* Reset the Output Compare and Output Compare N IDLE State */ tmpcr2 &= ~TIM_CR2_OIS2; tmpcr2 &= ~TIM_CR2_OIS2N; /* Set the Output Idle state */ tmpcr2 |= (OC_Config->OCIdleState << 2U); /* Set the Output N Idle state */ tmpcr2 |= (OC_Config->OCNIdleState << 2U); } /* Write to TIMx CR2 */ TIMx->CR2 = tmpcr2; /* Write to TIMx CCMR1 */ TIMx->CCMR1 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCR2 = OC_Config->Pulse; /* Write to TIMx CCER */ TIMx->CCER = tmpccer; } /** * @brief TIM DMA Delay Pulse complete callback. * @param hdma pointer to a DMA_HandleTypeDef structure that contains * the configuration information for the specified DMA module. * @retval None */ void TIM_DMADelayPulseCplt(DMA_HandleTypeDef *hdma) { TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; htim->State= HAL_TIM_STATE_READY; if(hdma == htim->hdma[TIM_DMA_ID_CC1]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1; } else if(hdma == htim->hdma[TIM_DMA_ID_CC2]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2; } else if(hdma == htim->hdma[TIM_DMA_ID_CC3]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3; } else if(hdma == htim->hdma[TIM_DMA_ID_CC4]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4; } HAL_TIM_PWM_PulseFinishedCallback(htim); htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } /** * @brief TIM DMA error callback * @param hdma pointer to a DMA_HandleTypeDef structure that contains * the configuration information for the specified DMA module. * @retval None */ void TIM_DMAError(DMA_HandleTypeDef *hdma) { TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; htim->State= HAL_TIM_STATE_READY; HAL_TIM_ErrorCallback(htim); } /** * @brief TIM DMA Capture complete callback. * @param hdma pointer to a DMA_HandleTypeDef structure that contains * the configuration information for the specified DMA module. * @retval None */ void TIM_DMACaptureCplt(DMA_HandleTypeDef *hdma) { TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; htim->State= HAL_TIM_STATE_READY; if(hdma == htim->hdma[TIM_DMA_ID_CC1]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1; } else if(hdma == htim->hdma[TIM_DMA_ID_CC2]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2; } else if(hdma == htim->hdma[TIM_DMA_ID_CC3]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3; } else if(hdma == htim->hdma[TIM_DMA_ID_CC4]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4; } HAL_TIM_IC_CaptureCallback(htim); htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } /** * @brief Enables or disables the TIM Capture Compare Channel x. * @param TIMx to select the TIM peripheral * @param Channel specifies the TIM Channel * This parameter can be one of the following values: * @arg TIM_Channel_1: TIM Channel 1 * @arg TIM_Channel_2: TIM Channel 2 * @arg TIM_Channel_3: TIM Channel 3 * @arg TIM_Channel_4: TIM Channel 4 * @param ChannelState specifies the TIM Channel CCxE bit new state. * This parameter can be: TIM_CCx_ENABLE or TIM_CCx_Disable. * @retval None */ void TIM_CCxChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelState) { uint32_t tmp = 0U; /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(TIMx)); assert_param(IS_TIM_CHANNELS(Channel)); tmp = TIM_CCER_CC1E << Channel; /* Reset the CCxE Bit */ TIMx->CCER &= ~tmp; /* Set or reset the CCxE Bit */ TIMx->CCER |= (uint32_t)(ChannelState << Channel); } /** * @brief TIM DMA Period Elapse complete callback. * @param hdma pointer to a DMA_HandleTypeDef structure that contains * the configuration information for the specified DMA module. * @retval None */ static void TIM_DMAPeriodElapsedCplt(DMA_HandleTypeDef *hdma) { TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; htim->State= HAL_TIM_STATE_READY; HAL_TIM_PeriodElapsedCallback(htim); } /** * @brief TIM DMA Trigger callback. * @param hdma pointer to a DMA_HandleTypeDef structure that contains * the configuration information for the specified DMA module. * @retval None */ static void TIM_DMATriggerCplt(DMA_HandleTypeDef *hdma) { TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; htim->State= HAL_TIM_STATE_READY; HAL_TIM_TriggerCallback(htim); } /** * @brief Time Output Compare 1 configuration * @param TIMx to select the TIM peripheral * @param OC_Config The output configuration structure * @retval None */ static void TIM_OC1_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config) { uint32_t tmpccmrx = 0U; uint32_t tmpccer = 0U; uint32_t tmpcr2 = 0U; /* Disable the Channel 1: Reset the CC1E Bit */ TIMx->CCER &= ~TIM_CCER_CC1E; /* Get the TIMx CCER register value */ tmpccer = TIMx->CCER; /* Get the TIMx CR2 register value */ tmpcr2 = TIMx->CR2; /* Get the TIMx CCMR1 register value */ tmpccmrx = TIMx->CCMR1; /* Reset the Output Compare Mode Bits */ tmpccmrx &= ~TIM_CCMR1_OC1M; tmpccmrx &= ~TIM_CCMR1_CC1S; /* Select the Output Compare Mode */ tmpccmrx |= OC_Config->OCMode; /* Reset the Output Polarity level */ tmpccer &= ~TIM_CCER_CC1P; /* Set the Output Compare Polarity */ tmpccer |= OC_Config->OCPolarity; if(IS_TIM_ADVANCED_INSTANCE(TIMx) != RESET) { /* Reset the Output N Polarity level */ tmpccer &= ~TIM_CCER_CC1NP; /* Set the Output N Polarity */ tmpccer |= OC_Config->OCNPolarity; /* Reset the Output N State */ tmpccer &= ~TIM_CCER_CC1NE; /* Reset the Output Compare and Output Compare N IDLE State */ tmpcr2 &= ~TIM_CR2_OIS1; tmpcr2 &= ~TIM_CR2_OIS1N; /* Set the Output Idle state */ tmpcr2 |= OC_Config->OCIdleState; /* Set the Output N Idle state */ tmpcr2 |= OC_Config->OCNIdleState; } /* Write to TIMx CR2 */ TIMx->CR2 = tmpcr2; /* Write to TIMx CCMR1 */ TIMx->CCMR1 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCR1 = OC_Config->Pulse; /* Write to TIMx CCER */ TIMx->CCER = tmpccer; } /** * @brief Time Output Compare 3 configuration * @param TIMx to select the TIM peripheral * @param OC_Config The output configuration structure * @retval None */ static void TIM_OC3_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config) { uint32_t tmpccmrx = 0U; uint32_t tmpccer = 0U; uint32_t tmpcr2 = 0U; /* Disable the Channel 3: Reset the CC2E Bit */ TIMx->CCER &= ~TIM_CCER_CC3E; /* Get the TIMx CCER register value */ tmpccer = TIMx->CCER; /* Get the TIMx CR2 register value */ tmpcr2 = TIMx->CR2; /* Get the TIMx CCMR2 register value */ tmpccmrx = TIMx->CCMR2; /* Reset the Output Compare mode and Capture/Compare selection Bits */ tmpccmrx &= ~TIM_CCMR2_OC3M; tmpccmrx &= ~TIM_CCMR2_CC3S; /* Select the Output Compare Mode */ tmpccmrx |= OC_Config->OCMode; /* Reset the Output Polarity level */ tmpccer &= ~TIM_CCER_CC3P; /* Set the Output Compare Polarity */ tmpccer |= (OC_Config->OCPolarity << 8U); if(IS_TIM_ADVANCED_INSTANCE(TIMx) != RESET) { assert_param(IS_TIM_OCN_POLARITY(OC_Config->OCNPolarity)); assert_param(IS_TIM_OCNIDLE_STATE(OC_Config->OCNIdleState)); assert_param(IS_TIM_OCIDLE_STATE(OC_Config->OCIdleState)); /* Reset the Output N Polarity level */ tmpccer &= ~TIM_CCER_CC3NP; /* Set the Output N Polarity */ tmpccer |= (OC_Config->OCNPolarity << 8U); /* Reset the Output N State */ tmpccer &= ~TIM_CCER_CC3NE; /* Reset the Output Compare and Output Compare N IDLE State */ tmpcr2 &= ~TIM_CR2_OIS3; tmpcr2 &= ~TIM_CR2_OIS3N; /* Set the Output Idle state */ tmpcr2 |= (OC_Config->OCIdleState << 4U); /* Set the Output N Idle state */ tmpcr2 |= (OC_Config->OCNIdleState << 4U); } /* Write to TIMx CR2 */ TIMx->CR2 = tmpcr2; /* Write to TIMx CCMR2 */ TIMx->CCMR2 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCR3 = OC_Config->Pulse; /* Write to TIMx CCER */ TIMx->CCER = tmpccer; } /** * @brief Time Output Compare 4 configuration * @param TIMx to select the TIM peripheral * @param OC_Config The output configuration structure * @retval None */ static void TIM_OC4_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config) { uint32_t tmpccmrx = 0U; uint32_t tmpccer = 0U; uint32_t tmpcr2 = 0U; /* Disable the Channel 4: Reset the CC4E Bit */ TIMx->CCER &= ~TIM_CCER_CC4E; /* Get the TIMx CCER register value */ tmpccer = TIMx->CCER; /* Get the TIMx CR2 register value */ tmpcr2 = TIMx->CR2; /* Get the TIMx CCMR2 register value */ tmpccmrx = TIMx->CCMR2; /* Reset the Output Compare mode and Capture/Compare selection Bits */ tmpccmrx &= ~TIM_CCMR2_OC4M; tmpccmrx &= ~TIM_CCMR2_CC4S; /* Select the Output Compare Mode */ tmpccmrx |= (OC_Config->OCMode << 8U); /* Reset the Output Polarity level */ tmpccer &= ~TIM_CCER_CC4P; /* Set the Output Compare Polarity */ tmpccer |= (OC_Config->OCPolarity << 12U); /*if((TIMx == TIM1) || (TIMx == TIM8))*/ if(IS_TIM_ADVANCED_INSTANCE(TIMx) != RESET) { assert_param(IS_TIM_OCIDLE_STATE(OC_Config->OCIdleState)); /* Reset the Output Compare IDLE State */ tmpcr2 &= ~TIM_CR2_OIS4; /* Set the Output Idle state */ tmpcr2 |= (OC_Config->OCIdleState << 6U); } /* Write to TIMx CR2 */ TIMx->CR2 = tmpcr2; /* Write to TIMx CCMR2 */ TIMx->CCMR2 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCR4 = OC_Config->Pulse; /* Write to TIMx CCER */ TIMx->CCER = tmpccer; } /** * @brief Time Output Compare 4 configuration * @param htim pointer to a TIM_HandleTypeDef structure that contains * the configuration information for TIM module. * @param sSlaveConfig The slave configuration structure * @retval None */ static void TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef *htim, TIM_SlaveConfigTypeDef * sSlaveConfig) { uint32_t tmpsmcr = 0U; uint32_t tmpccmr1 = 0U; uint32_t tmpccer = 0U; /* Get the TIMx SMCR register value */ tmpsmcr = htim->Instance->SMCR; /* Reset the Trigger Selection Bits */ tmpsmcr &= ~TIM_SMCR_TS; /* Set the Input Trigger source */ tmpsmcr |= sSlaveConfig->InputTrigger; /* Reset the slave mode Bits */ tmpsmcr &= ~TIM_SMCR_SMS; /* Set the slave mode */ tmpsmcr |= sSlaveConfig->SlaveMode; /* Write to TIMx SMCR */ htim->Instance->SMCR = tmpsmcr; /* Configure the trigger prescaler, filter, and polarity */ switch (sSlaveConfig->InputTrigger) { case TIM_TS_ETRF: { /* Check the parameters */ assert_param(IS_TIM_ETR_INSTANCE(htim->Instance)); assert_param(IS_TIM_TRIGGERPRESCALER(sSlaveConfig->TriggerPrescaler)); assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity)); assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter)); /* Configure the ETR Trigger source */ TIM_ETR_SetConfig(htim->Instance, sSlaveConfig->TriggerPrescaler, sSlaveConfig->TriggerPolarity, sSlaveConfig->TriggerFilter); } break; case TIM_TS_TI1F_ED: { /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter)); /* Disable the Channel 1: Reset the CC1E Bit */ tmpccer = htim->Instance->CCER; htim->Instance->CCER &= ~TIM_CCER_CC1E; tmpccmr1 = htim->Instance->CCMR1; /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC1F; tmpccmr1 |= ((sSlaveConfig->TriggerFilter) << 4U); /* Write to TIMx CCMR1 and CCER registers */ htim->Instance->CCMR1 = tmpccmr1; htim->Instance->CCER = tmpccer; } break; case TIM_TS_TI1FP1: { /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity)); assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter)); /* Configure TI1 Filter and Polarity */ TIM_TI1_ConfigInputStage(htim->Instance, sSlaveConfig->TriggerPolarity, sSlaveConfig->TriggerFilter); } break; case TIM_TS_TI2FP2: { /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity)); assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter)); /* Configure TI2 Filter and Polarity */ TIM_TI2_ConfigInputStage(htim->Instance, sSlaveConfig->TriggerPolarity, sSlaveConfig->TriggerFilter); } break; case TIM_TS_ITR0: { /* Check the parameter */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); } break; case TIM_TS_ITR1: { /* Check the parameter */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); } break; case TIM_TS_ITR2: { /* Check the parameter */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); } break; case TIM_TS_ITR3: { /* Check the parameter */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); } break; default: break; } } /** * @brief Configure the Polarity and Filter for TI1. * @param TIMx to select the TIM peripheral. * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_ICPolarity_Rising * @arg TIM_ICPolarity_Falling * @arg TIM_ICPolarity_BothEdge * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @retval None */ static void TIM_TI1_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter) { uint32_t tmpccmr1 = 0U; uint32_t tmpccer = 0U; /* Disable the Channel 1: Reset the CC1E Bit */ tmpccer = TIMx->CCER; TIMx->CCER &= ~TIM_CCER_CC1E; tmpccmr1 = TIMx->CCMR1; /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC1F; tmpccmr1 |= (TIM_ICFilter << 4U); /* Select the Polarity and set the CC1E Bit */ tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC1NP); tmpccer |= TIM_ICPolarity; /* Write to TIMx CCMR1 and CCER registers */ TIMx->CCMR1 = tmpccmr1; TIMx->CCER = tmpccer; } /** * @brief Configure the TI2 as Input. * @param TIMx to select the TIM peripheral * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_ICPolarity_Rising * @arg TIM_ICPolarity_Falling * @arg TIM_ICPolarity_BothEdge * @param TIM_ICSelection specifies the input to be used. * This parameter can be one of the following values: * @arg TIM_ICSelection_DirectTI: TIM Input 2 is selected to be connected to IC2. * @arg TIM_ICSelection_IndirectTI: TIM Input 2 is selected to be connected to IC1. * @arg TIM_ICSelection_TRC: TIM Input 2 is selected to be connected to TRC. * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI1FP2 * (on channel1 path) is used as the input signal. Therefore CCMR1 must be * protected against un-initialized filter and polarity values. * @retval None */ static void TIM_TI2_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter) { uint32_t tmpccmr1 = 0U; uint32_t tmpccer = 0U; /* Disable the Channel 2: Reset the CC2E Bit */ TIMx->CCER &= ~TIM_CCER_CC2E; tmpccmr1 = TIMx->CCMR1; tmpccer = TIMx->CCER; /* Select the Input */ tmpccmr1 &= ~TIM_CCMR1_CC2S; tmpccmr1 |= (TIM_ICSelection << 8U); /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC2F; tmpccmr1 |= ((TIM_ICFilter << 12U) & TIM_CCMR1_IC2F); /* Select the Polarity and set the CC2E Bit */ tmpccer &= ~(TIM_CCER_CC2P | TIM_CCER_CC2NP); tmpccer |= ((TIM_ICPolarity << 4U) & (TIM_CCER_CC2P | TIM_CCER_CC2NP)); /* Write to TIMx CCMR1 and CCER registers */ TIMx->CCMR1 = tmpccmr1 ; TIMx->CCER = tmpccer; } /** * @brief Configure the Polarity and Filter for TI2. * @param TIMx to select the TIM peripheral. * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_ICPolarity_Rising * @arg TIM_ICPolarity_Falling * @arg TIM_ICPolarity_BothEdge * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @retval None */ static void TIM_TI2_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter) { uint32_t tmpccmr1 = 0U; uint32_t tmpccer = 0U; /* Disable the Channel 2: Reset the CC2E Bit */ TIMx->CCER &= ~TIM_CCER_CC2E; tmpccmr1 = TIMx->CCMR1; tmpccer = TIMx->CCER; /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC2F; tmpccmr1 |= (TIM_ICFilter << 12U); /* Select the Polarity and set the CC2E Bit */ tmpccer &= ~(TIM_CCER_CC2P | TIM_CCER_CC2NP); tmpccer |= (TIM_ICPolarity << 4U); /* Write to TIMx CCMR1 and CCER registers */ TIMx->CCMR1 = tmpccmr1 ; TIMx->CCER = tmpccer; } /** * @brief Configure the TI3 as Input. * @param TIMx to select the TIM peripheral * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_ICPolarity_Rising * @arg TIM_ICPolarity_Falling * @arg TIM_ICPolarity_BothEdge * @param TIM_ICSelection specifies the input to be used. * This parameter can be one of the following values: * @arg TIM_ICSelection_DirectTI: TIM Input 3 is selected to be connected to IC3. * @arg TIM_ICSelection_IndirectTI: TIM Input 3 is selected to be connected to IC4. * @arg TIM_ICSelection_TRC: TIM Input 3 is selected to be connected to TRC. * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI4FP3 * (on channel4 path) is used as the input signal. Therefore CCMR2 must be * protected against un-initialized filter and polarity values. * @retval None */ static void TIM_TI3_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter) { uint32_t tmpccmr2 = 0U; uint32_t tmpccer = 0U; /* Disable the Channel 3: Reset the CC3E Bit */ TIMx->CCER &= ~TIM_CCER_CC3E; tmpccmr2 = TIMx->CCMR2; tmpccer = TIMx->CCER; /* Select the Input */ tmpccmr2 &= ~TIM_CCMR2_CC3S; tmpccmr2 |= TIM_ICSelection; /* Set the filter */ tmpccmr2 &= ~TIM_CCMR2_IC3F; tmpccmr2 |= ((TIM_ICFilter << 4U) & TIM_CCMR2_IC3F); /* Select the Polarity and set the CC3E Bit */ tmpccer &= ~(TIM_CCER_CC3P | TIM_CCER_CC3NP); tmpccer |= ((TIM_ICPolarity << 8U) & (TIM_CCER_CC3P | TIM_CCER_CC3NP)); /* Write to TIMx CCMR2 and CCER registers */ TIMx->CCMR2 = tmpccmr2; TIMx->CCER = tmpccer; } /** * @brief Configure the TI4 as Input. * @param TIMx to select the TIM peripheral * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_ICPolarity_Rising * @arg TIM_ICPolarity_Falling * @arg TIM_ICPolarity_BothEdge * @param TIM_ICSelection specifies the input to be used. * This parameter can be one of the following values: * @arg TIM_ICSelection_DirectTI: TIM Input 4 is selected to be connected to IC4. * @arg TIM_ICSelection_IndirectTI: TIM Input 4 is selected to be connected to IC3. * @arg TIM_ICSelection_TRC: TIM Input 4 is selected to be connected to TRC. * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI3FP4 * (on channel3 path) is used as the input signal. Therefore CCMR2 must be * protected against un-initialized filter and polarity values. * @retval None */ static void TIM_TI4_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter) { uint32_t tmpccmr2 = 0U; uint32_t tmpccer = 0U; /* Disable the Channel 4: Reset the CC4E Bit */ TIMx->CCER &= ~TIM_CCER_CC4E; tmpccmr2 = TIMx->CCMR2; tmpccer = TIMx->CCER; /* Select the Input */ tmpccmr2 &= ~TIM_CCMR2_CC4S; tmpccmr2 |= (TIM_ICSelection << 8U); /* Set the filter */ tmpccmr2 &= ~TIM_CCMR2_IC4F; tmpccmr2 |= ((TIM_ICFilter << 12U) & TIM_CCMR2_IC4F); /* Select the Polarity and set the CC4E Bit */ tmpccer &= ~(TIM_CCER_CC4P | TIM_CCER_CC4NP); tmpccer |= ((TIM_ICPolarity << 12U) & (TIM_CCER_CC4P | TIM_CCER_CC4NP)); /* Write to TIMx CCMR2 and CCER registers */ TIMx->CCMR2 = tmpccmr2; TIMx->CCER = tmpccer ; } /** * @brief Selects the Input Trigger source * @param TIMx to select the TIM peripheral * @param TIM_ITRx The Input Trigger source. * This parameter can be one of the following values: * @arg TIM_TS_ITR0: Internal Trigger 0 * @arg TIM_TS_ITR1: Internal Trigger 1 * @arg TIM_TS_ITR2: Internal Trigger 2 * @arg TIM_TS_ITR3: Internal Trigger 3 * @arg TIM_TS_TI1F_ED: TI1 Edge Detector * @arg TIM_TS_TI1FP1: Filtered Timer Input 1 * @arg TIM_TS_TI2FP2: Filtered Timer Input 2 * @arg TIM_TS_ETRF: External Trigger input * @retval None */ static void TIM_ITRx_SetConfig(TIM_TypeDef *TIMx, uint16_t TIM_ITRx) { uint32_t tmpsmcr = 0U; /* Get the TIMx SMCR register value */ tmpsmcr = TIMx->SMCR; /* Reset the TS Bits */ tmpsmcr &= ~TIM_SMCR_TS; /* Set the Input Trigger source and the slave mode*/ tmpsmcr |= TIM_ITRx | TIM_SLAVEMODE_EXTERNAL1; /* Write to TIMx SMCR */ TIMx->SMCR = tmpsmcr; } /** * @brief Configures the TIMx External Trigger (ETR). * @param TIMx to select the TIM peripheral * @param TIM_ExtTRGPrescaler The external Trigger Prescaler. * This parameter can be one of the following values: * @arg TIM_ETRPRESCALER_DIV1 : ETRP Prescaler OFF. * @arg TIM_ETRPRESCALER_DIV2 : ETRP frequency divided by 2. * @arg TIM_ETRPRESCALER_DIV4 : ETRP frequency divided by 4. * @arg TIM_ETRPRESCALER_DIV8 : ETRP frequency divided by 8. * @param TIM_ExtTRGPolarity The external Trigger Polarity. * This parameter can be one of the following values: * @arg TIM_ETRPOLARITY_INVERTED : active low or falling edge active. * @arg TIM_ETRPOLARITY_NONINVERTED : active high or rising edge active. * @param ExtTRGFilter External Trigger Filter. * This parameter must be a value between 0x00 and 0x0F * @retval None */ static void TIM_ETR_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ExtTRGPrescaler, uint32_t TIM_ExtTRGPolarity, uint32_t ExtTRGFilter) { uint32_t tmpsmcr = 0U; tmpsmcr = TIMx->SMCR; /* Reset the ETR Bits */ tmpsmcr &= ~(TIM_SMCR_ETF | TIM_SMCR_ETPS | TIM_SMCR_ECE | TIM_SMCR_ETP); /* Set the Prescaler, the Filter value and the Polarity */ tmpsmcr |= (uint32_t)(TIM_ExtTRGPrescaler | (TIM_ExtTRGPolarity | (ExtTRGFilter << 8))); /* Write to TIMx SMCR */ TIMx->SMCR = tmpsmcr; } /** * @} */ #endif /* HAL_TIM_MODULE_ENABLED */ /** * @} */ /** * @} */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/