view Common/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_irda.c @ 949:c6b858f2e025 Evo_2_23 tip

GNSS UTC in Date-Time menu: The UTC time provided by the gnss module is not shown in the date-time settings menu. If a valid time signal is available then the OSTC RTC may be set to it by selecting the UTC menu entry. The time zone has to be selected manually. This is possible using a separate edit line.
author Ideenmodellierer
date Sun, 22 Dec 2024 21:19:21 +0100
parents c78bcbd5deda
children
line wrap: on
line source

/**
  ******************************************************************************
  * @file    stm32f4xx_hal_irda.c
  * @author  MCD Application Team
  * @brief   IRDA HAL module driver.
  *          This file provides firmware functions to manage the following 
  *          functionalities of the IrDA SIR ENDEC block (IrDA):
  *           + Initialization and de-initialization methods
  *           + IO operation methods
  *           + Peripheral Control methods
  *
  @verbatim
  ==============================================================================
                        ##### How to use this driver #####
  ==============================================================================
  [..]
    The IRDA HAL driver can be used as follows:
    
    (#) Declare a IRDA_HandleTypeDef handle structure.
    (#) Initialize the IRDA low level resources by implementing the HAL_IRDA_MspInit() API:
        (##) Enable the USARTx interface clock.
        (##) IRDA pins configuration:
            (+++) Enable the clock for the IRDA GPIOs.
            (+++) Configure these IRDA pins as alternate function pull-up.
        (##) NVIC configuration if you need to use interrupt process (HAL_IRDA_Transmit_IT()
             and HAL_IRDA_Receive_IT() APIs):
            (+++) Configure the USARTx interrupt priority.
            (+++) Enable the NVIC USART IRQ handle.
        (##) DMA Configuration if you need to use DMA process (HAL_IRDA_Transmit_DMA()
             and HAL_IRDA_Receive_DMA() APIs):
            (+++) Declare a DMA handle structure for the Tx/Rx stream.
            (+++) Enable the DMAx interface clock.
            (+++) Configure the declared DMA handle structure with the required Tx/Rx parameters.                
            (+++) Configure the DMA Tx/Rx Stream.
            (+++) Associate the initialized DMA handle to the IRDA DMA Tx/Rx handle.
            (+++) Configure the priority and enable the NVIC for the transfer complete interrupt on the DMA Tx/Rx Stream.

    (#) Program the Baud Rate, Word Length, Parity, IrDA Mode, Prescaler 
        and Mode(Receiver/Transmitter) in the hirda Init structure.

    (#) Initialize the IRDA registers by calling the HAL_IRDA_Init() API:
        (++) This API configures also the low level Hardware GPIO, CLOCK, CORTEX...etc)
            by calling the customized HAL_IRDA_MspInit() API.
    -@@- The specific IRDA interrupts (Transmission complete interrupt, 
        RXNE interrupt and Error Interrupts) will be managed using the macros
        __HAL_IRDA_ENABLE_IT() and __HAL_IRDA_DISABLE_IT() inside the transmit and receive process.
        
    (#) Three operation modes are available within this driver :
             
    *** Polling mode IO operation ***
    =================================
    [..]    
      (+) Send an amount of data in blocking mode using HAL_IRDA_Transmit() 
      (+) Receive an amount of data in blocking mode using HAL_IRDA_Receive()
       
    *** Interrupt mode IO operation ***    
    ===================================
    [..]    
      (+) Send an amount of data in non blocking mode using HAL_IRDA_Transmit_IT() 
      (+) At transmission end of transfer HAL_IRDA_TxCpltCallback is executed and user can 
           add his own code by customization of function pointer HAL_IRDA_TxCpltCallback
      (+) Receive an amount of data in non blocking mode using HAL_IRDA_Receive_IT() 
      (+) At reception end of transfer HAL_IRDA_RxCpltCallback is executed and user can 
           add his own code by customization of function pointer HAL_IRDA_RxCpltCallback                                      
      (+) In case of transfer Error, HAL_IRDA_ErrorCallback() function is executed and user can 
           add his own code by customization of function pointer HAL_IRDA_ErrorCallback

    *** DMA mode IO operation ***    
    =============================
    [..]
      (+) Send an amount of data in non blocking mode (DMA) using HAL_IRDA_Transmit_DMA() 
      (+) At transmission end of transfer HAL_IRDA_TxCpltCallback is executed and user can 
           add his own code by customization of function pointer HAL_IRDA_TxCpltCallback
      (+) Receive an amount of data in non blocking mode (DMA) using HAL_IRDA_Receive_DMA() 
      (+) At reception end of transfer HAL_IRDA_RxCpltCallback is executed and user can 
           add his own code by customization of function pointer HAL_IRDA_RxCpltCallback                                      
      (+) In case of transfer Error, HAL_IRDA_ErrorCallback() function is executed and user can 
           add his own code by customization of function pointer HAL_IRDA_ErrorCallback    

    *** IRDA HAL driver macros list ***
    ===================================
    [..]
      Below the list of most used macros in IRDA HAL driver.
       
     (+) __HAL_IRDA_ENABLE: Enable the IRDA peripheral 
     (+) __HAL_IRDA_DISABLE: Disable the IRDA peripheral     
     (+) __HAL_IRDA_GET_FLAG : Checks whether the specified IRDA flag is set or not
     (+) __HAL_IRDA_CLEAR_FLAG : Clears the specified IRDA pending flag
     (+) __HAL_IRDA_ENABLE_IT: Enables the specified IRDA interrupt
     (+) __HAL_IRDA_DISABLE_IT: Disables the specified IRDA interrupt

    [..]
     (@) You can refer to the IRDA HAL driver header file for more useful macros

  @endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
  *
  * Redistribution and use in source and binary forms, with or without modification,
  * are permitted provided that the following conditions are met:
  *   1. Redistributions of source code must retain the above copyright notice,
  *      this list of conditions and the following disclaimer.
  *   2. Redistributions in binary form must reproduce the above copyright notice,
  *      this list of conditions and the following disclaimer in the documentation
  *      and/or other materials provided with the distribution.
  *   3. Neither the name of STMicroelectronics nor the names of its contributors
  *      may be used to endorse or promote products derived from this software
  *      without specific prior written permission.
  *
  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  *
  ******************************************************************************
  */ 

/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_hal.h"

/** @addtogroup STM32F4xx_HAL_Driver
  * @{
  */

/** @defgroup IRDA IRDA
  * @brief HAL IRDA module driver
  * @{
  */

#ifdef HAL_IRDA_MODULE_ENABLED

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/** @addtogroup IRDA_Private_Constants
  * @{
  */
/**
  * @}
  */
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/** @addtogroup IRDA_Private_Functions
  * @{
  */
static void IRDA_SetConfig (IRDA_HandleTypeDef *hirda);
static HAL_StatusTypeDef IRDA_Transmit_IT(IRDA_HandleTypeDef *hirda);
static HAL_StatusTypeDef IRDA_EndTransmit_IT(IRDA_HandleTypeDef *hirda);
static HAL_StatusTypeDef IRDA_Receive_IT(IRDA_HandleTypeDef *hirda);
static void IRDA_DMATransmitCplt(DMA_HandleTypeDef *hdma);
static void IRDA_DMATransmitHalfCplt(DMA_HandleTypeDef *hdma);
static void IRDA_DMAReceiveCplt(DMA_HandleTypeDef *hdma);
static void IRDA_DMAReceiveHalfCplt(DMA_HandleTypeDef *hdma);
static void IRDA_DMAError(DMA_HandleTypeDef *hdma);
static void IRDA_DMAAbortOnError(DMA_HandleTypeDef *hdma);
static void IRDA_DMATxAbortCallback(DMA_HandleTypeDef *hdma);
static void IRDA_DMARxAbortCallback(DMA_HandleTypeDef *hdma);
static void IRDA_DMATxOnlyAbortCallback(DMA_HandleTypeDef *hdma);
static void IRDA_DMARxOnlyAbortCallback(DMA_HandleTypeDef *hdma);
static HAL_StatusTypeDef IRDA_WaitOnFlagUntilTimeout(IRDA_HandleTypeDef *hirda, uint32_t Flag, FlagStatus Status, uint32_t Tickstart,uint32_t Timeout);
static void IRDA_EndTxTransfer(IRDA_HandleTypeDef *hirda);
static void IRDA_EndRxTransfer(IRDA_HandleTypeDef *hirda);
/**
  * @}
  */
/* Exported functions --------------------------------------------------------*/
/** @defgroup IRDA_Exported_Functions IrDA Exported Functions
  * @{
  */

/** @defgroup IRDA_Exported_Functions_Group1 IrDA Initialization and de-initialization functions 
  *  @brief    Initialization and Configuration functions 
  *
@verbatim 

===============================================================================
            ##### Initialization and Configuration functions #####
 ===============================================================================  
    [..]
    This subsection provides a set of functions allowing to initialize the USARTx or the UARTy 
    in IrDA mode.
      (+) For the asynchronous mode only these parameters can be configured: 
        (++) BaudRate
        (++) WordLength 
        (++) Parity: If the parity is enabled, then the MSB bit of the data written
             in the data register is transmitted but is changed by the parity bit.
             Depending on the frame length defined by the M bit (8-bits or 9-bits),
             please refer to Reference manual for possible IRDA frame formats.
        (++) Prescaler: A pulse of width less than two and greater than one PSC period(s) may or may
             not be rejected. The receiver set up time should be managed by software. The IrDA physical layer
             specification specifies a minimum of 10 ms delay between transmission and 
             reception (IrDA is a half duplex protocol).
        (++) Mode: Receiver/transmitter modes
        (++) IrDAMode: the IrDA can operate in the Normal mode or in the Low power mode.
    [..]
    The HAL_IRDA_Init() API follows IRDA configuration procedures (details for the procedures
    are available in reference manual).

@endverbatim
  * @{
  */

/**
  * @brief  Initializes the IRDA mode according to the specified
  *         parameters in the IRDA_InitTypeDef and create the associated handle.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Init(IRDA_HandleTypeDef *hirda)
{
  /* Check the IRDA handle allocation */
  if(hirda == NULL)
  {
    return HAL_ERROR;
  }
  
  /* Check the IRDA instance parameters */
  assert_param(IS_IRDA_INSTANCE(hirda->Instance));
  /* Check the IRDA mode parameter in the IRDA handle */
  assert_param(IS_IRDA_POWERMODE(hirda->Init.IrDAMode)); 
  
  if(hirda->gState == HAL_IRDA_STATE_RESET)
  {
    /* Allocate lock resource and initialize it */
    hirda->Lock = HAL_UNLOCKED;
    /* Init the low level hardware : GPIO, CLOCK, CORTEX...etc */
    HAL_IRDA_MspInit(hirda);
  }
  
  hirda->gState = HAL_IRDA_STATE_BUSY;
  
  /* Disable the IRDA peripheral */
  __HAL_IRDA_DISABLE(hirda);
  
  /* Set the IRDA communication parameters */
  IRDA_SetConfig(hirda);
  
  /* In IrDA mode, the following bits must be kept cleared: 
  - LINEN, STOP and CLKEN bits in the USART_CR2 register,
  - SCEN and HDSEL bits in the USART_CR3 register.*/
  CLEAR_BIT(hirda->Instance->CR2, USART_CR2_LINEN | USART_CR2_STOP | USART_CR2_CLKEN);
  CLEAR_BIT(hirda->Instance->CR3, USART_CR3_SCEN | USART_CR3_HDSEL);
  
  /* Enable the IRDA peripheral */
  __HAL_IRDA_ENABLE(hirda);
  
  /* Set the prescaler */
  MODIFY_REG(hirda->Instance->GTPR, USART_GTPR_PSC, hirda->Init.Prescaler);
  
  /* Configure the IrDA mode */
  MODIFY_REG(hirda->Instance->CR3, USART_CR3_IRLP, hirda->Init.IrDAMode);
  
  /* Enable the IrDA mode by setting the IREN bit in the CR3 register */
  SET_BIT(hirda->Instance->CR3, USART_CR3_IREN);
  
  /* Initialize the IRDA state*/
  hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
  hirda->gState= HAL_IRDA_STATE_READY;
  hirda->RxState= HAL_IRDA_STATE_READY;
  
  return HAL_OK;
}

/**
  * @brief  DeInitializes the IRDA peripheral 
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_DeInit(IRDA_HandleTypeDef *hirda)
{
  /* Check the IRDA handle allocation */
  if(hirda == NULL)
  {
    return HAL_ERROR;
  }
  
  /* Check the parameters */
  assert_param(IS_IRDA_INSTANCE(hirda->Instance)); 
  
  hirda->gState = HAL_IRDA_STATE_BUSY;
  
  /* Disable the Peripheral */
  __HAL_IRDA_DISABLE(hirda);
  
  /* DeInit the low level hardware */
  HAL_IRDA_MspDeInit(hirda);
  
  hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
  
  hirda->gState = HAL_IRDA_STATE_RESET; 
  hirda->RxState = HAL_IRDA_STATE_RESET;
  
  /* Release Lock */
  __HAL_UNLOCK(hirda);
  
  return HAL_OK;
}

/**
  * @brief  IRDA MSP Init.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
__weak void HAL_IRDA_MspInit(IRDA_HandleTypeDef *hirda)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hirda);
  /* NOTE : This function Should not be modified, when the callback is needed,
  the HAL_IRDA_MspInit could be implemented in the user file
  */ 
}

/**
  * @brief  IRDA MSP DeInit.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
__weak void HAL_IRDA_MspDeInit(IRDA_HandleTypeDef *hirda)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hirda);
  /* NOTE : This function Should not be modified, when the callback is needed,
  the HAL_IRDA_MspDeInit could be implemented in the user file
  */ 
}

/**
  * @}
  */

/** @defgroup IRDA_Exported_Functions_Group2 IO operation functions 
  *  @brief   IRDA Transmit/Receive functions 
  *
@verbatim   
 ===============================================================================
                      ##### IO operation functions #####
 ===============================================================================  
    This subsection provides a set of functions allowing to manage the IRDA data transfers.
    [..]
    IrDA is a half duplex communication protocol. If the Transmitter is busy, any data
    on the IrDA receive line will be ignored by the IrDA decoder and if the Receiver 
    is busy, data on the TX from the USART to IrDA will not be encoded by IrDA.
    While receiving data, transmission should be avoided as the data to be transmitted
    could be corrupted.

    (#) There are two modes of transfer:
       (++) Blocking mode: The communication is performed in polling mode. 
            The HAL status of all data processing is returned by the same function 
            after finishing transfer.  
       (++) No-Blocking mode: The communication is performed using Interrupts 
           or DMA, These APIs return the HAL status.
           The end of the data processing will be indicated through the 
           dedicated IRDA IRQ when using Interrupt mode or the DMA IRQ when 
           using DMA mode.
           The HAL_IRDA_TxCpltCallback(), HAL_IRDA_RxCpltCallback() user callbacks 
           will be executed respectively at the end of the transmit or Receive process
           The HAL_IRDA_ErrorCallback() user callback will be executed when a communication error is detected

    (#) Blocking mode API's are :
        (++) HAL_IRDA_Transmit()
        (++) HAL_IRDA_Receive() 
        
    (#) Non Blocking mode APIs with Interrupt are :
        (++) HAL_IRDA_Transmit_IT()
        (++) HAL_IRDA_Receive_IT()
        (++) HAL_IRDA_IRQHandler()

    (#) Non Blocking mode functions with DMA are :
        (++) HAL_IRDA_Transmit_DMA()
        (++) HAL_IRDA_Receive_DMA()

    (#) A set of Transfer Complete Callbacks are provided in non Blocking mode:
        (++) HAL_IRDA_TxCpltCallback()
        (++) HAL_IRDA_RxCpltCallback()
        (++) HAL_IRDA_ErrorCallback()

@endverbatim
  * @{
  */

/**
  * @brief  Sends an amount of data in blocking mode.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  pData Pointer to data buffer
  * @param  Size Amount of data to be sent
  * @param  Timeout Specify timeout value  
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Transmit(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size, uint32_t Timeout)
{
  uint16_t* tmp;
  uint32_t tickstart = 0U;
  
  /* Check that a Tx process is not already ongoing */
  if(hirda->gState == HAL_IRDA_STATE_READY) 
  {
    if((pData == NULL) || (Size == 0)) 
    {
      return  HAL_ERROR;
    }
    
    /* Process Locked */
    __HAL_LOCK(hirda);
    
    hirda->ErrorCode = HAL_IRDA_ERROR_NONE; 
    hirda->gState = HAL_IRDA_STATE_BUSY_TX;
    
    /* Init tickstart for timeout managment*/
    tickstart = HAL_GetTick();
    
    hirda->TxXferSize = Size;
    hirda->TxXferCount = Size;
    while(hirda->TxXferCount > 0U)
    {
      hirda->TxXferCount--;
      if(hirda->Init.WordLength == IRDA_WORDLENGTH_9B)
      {
        if(IRDA_WaitOnFlagUntilTimeout(hirda, IRDA_FLAG_TXE, RESET, tickstart, Timeout) != HAL_OK)
        { 
          return HAL_TIMEOUT;
        }
        tmp = (uint16_t*) pData;
        hirda->Instance->DR = (*tmp & (uint16_t)0x01FF);
        if(hirda->Init.Parity == IRDA_PARITY_NONE)
        {
          pData +=2;
        }
        else
        {
          pData +=1;
        }
      } 
      else
      {
        if(IRDA_WaitOnFlagUntilTimeout(hirda, IRDA_FLAG_TXE, RESET, tickstart, Timeout) != HAL_OK)
        {
          return HAL_TIMEOUT;
        }
        hirda->Instance->DR = (*pData++ & (uint8_t)0xFF);
      }
    }
    
    if(IRDA_WaitOnFlagUntilTimeout(hirda, IRDA_FLAG_TC, RESET, tickstart, Timeout) != HAL_OK)
    { 
      return HAL_TIMEOUT;
    }
    
    /* At end of Tx process, restore hirda->gState to Ready */
    hirda->gState = HAL_IRDA_STATE_READY;
    
    /* Process Unlocked */
    __HAL_UNLOCK(hirda);
    
    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;
  }
}

/**
  * @brief  Receive an amount of data in blocking mode. 
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  pData Pointer to data buffer
  * @param  Size Amount of data to be received
  * @param  Timeout Specify timeout value    
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Receive(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size, uint32_t Timeout)
{ 
  uint16_t* tmp;
  uint32_t tickstart = 0U;
  
  /* Check that a Rx process is not already ongoing */
  if(hirda->RxState == HAL_IRDA_STATE_READY) 
  {
    if((pData == NULL) || (Size == 0)) 
    {
      return  HAL_ERROR;
    }
    
    /* Process Locked */
    __HAL_LOCK(hirda);
    
    hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
    hirda->RxState = HAL_IRDA_STATE_BUSY_RX;
    
    /* Init tickstart for timeout managment*/
    tickstart = HAL_GetTick();
    
    hirda->RxXferSize = Size;
    hirda->RxXferCount = Size;
    /* Check the remain data to be received */
    while(hirda->RxXferCount > 0U)
    {
      hirda->RxXferCount--;
      if(hirda->Init.WordLength == IRDA_WORDLENGTH_9B)
      {
        if(IRDA_WaitOnFlagUntilTimeout(hirda, IRDA_FLAG_RXNE, RESET, tickstart, Timeout) != HAL_OK)
        { 
          return HAL_TIMEOUT;
        }
        tmp = (uint16_t*) pData ;
        if(hirda->Init.Parity == IRDA_PARITY_NONE)
        {
          *tmp = (uint16_t)(hirda->Instance->DR & (uint16_t)0x01FF);
          pData +=2;
        }
        else
        {
          *tmp = (uint16_t)(hirda->Instance->DR & (uint16_t)0x00FF);
          pData +=1;
        }
      } 
      else
      {
        if(IRDA_WaitOnFlagUntilTimeout(hirda, IRDA_FLAG_RXNE, RESET, tickstart, Timeout) != HAL_OK)
        { 
          return HAL_TIMEOUT;
        }
        if(hirda->Init.Parity == IRDA_PARITY_NONE)
        {
          *pData++ = (uint8_t)(hirda->Instance->DR & (uint8_t)0x00FF);
        }
        else
        {
          *pData++ = (uint8_t)(hirda->Instance->DR & (uint8_t)0x007F);
        }
      }
    }
    
    /* At end of Rx process, restore hirda->RxState to Ready */
    hirda->RxState = HAL_IRDA_STATE_READY;
    
    /* Process Unlocked */
    __HAL_UNLOCK(hirda);
    
    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;
  }
}

/**
  * @brief  Send an amount of data in non blocking mode. 
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  pData Pointer to data buffer
  * @param  Size Amount of data to be sent
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Transmit_IT(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size)
{
  /* Check that a Tx process is not already ongoing */
  if(hirda->gState == HAL_IRDA_STATE_READY) 
  {
    if((pData == NULL) || (Size == 0)) 
    {
      return HAL_ERROR;
    }
    /* Process Locked */
    __HAL_LOCK(hirda);

    hirda->pTxBuffPtr = pData;
    hirda->TxXferSize = Size;
    hirda->TxXferCount = Size;
    hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
    hirda->gState = HAL_IRDA_STATE_BUSY_TX;

    /* Process Unlocked */
    __HAL_UNLOCK(hirda);

    /* Enable the IRDA Transmit Data Register Empty Interrupt */
    SET_BIT(hirda->Instance->CR1, USART_CR1_TXEIE);

    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;
  }
}

/**
  * @brief  Receives an amount of data in non blocking mode. 
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  pData Pointer to data buffer
  * @param  Size Amount of data to be received
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Receive_IT(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size)
{
  /* Check that a Rx process is not already ongoing */	
  if(hirda->RxState == HAL_IRDA_STATE_READY) 
  {
    if((pData == NULL) || (Size == 0)) 
    {
      return HAL_ERROR;
    }
    
    /* Process Locked */
    __HAL_LOCK(hirda);
    
    hirda->pRxBuffPtr = pData;
    hirda->RxXferSize = Size;
    hirda->RxXferCount = Size;
    hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
    hirda->RxState = HAL_IRDA_STATE_BUSY_RX;
    
    /* Process Unlocked */
    __HAL_UNLOCK(hirda);

    /* Enable the IRDA Parity Error and Data Register not empty Interrupts */
    SET_BIT(hirda->Instance->CR1, USART_CR1_PEIE| USART_CR1_RXNEIE);

    /* Enable the IRDA Error Interrupt: (Frame error, noise error, overrun error) */
    SET_BIT(hirda->Instance->CR3, USART_CR3_EIE);

    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;
  }
}

/**
  * @brief  Sends an amount of data in non blocking mode. 
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  pData Pointer to data buffer
  * @param  Size Amount of data to be sent
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Transmit_DMA(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size)
{
  uint32_t *tmp;
  
  /* Check that a Tx process is not already ongoing */
  if(hirda->gState == HAL_IRDA_STATE_READY) 
  {
    if((pData == NULL) || (Size == 0)) 
    {
      return HAL_ERROR;
    }
    
    /* Process Locked */
    __HAL_LOCK(hirda);

    hirda->pTxBuffPtr = pData;
    hirda->TxXferSize = Size;
    hirda->TxXferCount = Size;
    hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
    hirda->gState = HAL_IRDA_STATE_BUSY_TX;

    /* Set the IRDA DMA transfer complete callback */
    hirda->hdmatx->XferCpltCallback = IRDA_DMATransmitCplt;

    /* Set the IRDA DMA half transfer complete callback */
    hirda->hdmatx->XferHalfCpltCallback = IRDA_DMATransmitHalfCplt;

    /* Set the DMA error callback */
    hirda->hdmatx->XferErrorCallback = IRDA_DMAError;

    /* Set the DMA abort callback */
    hirda->hdmatx->XferAbortCallback = NULL;

    /* Enable the IRDA transmit DMA Stream */
    tmp = (uint32_t*)&pData;
    HAL_DMA_Start_IT(hirda->hdmatx, *(uint32_t*)tmp, (uint32_t)&hirda->Instance->DR, Size);

    /* Clear the TC flag in the SR register by writing 0 to it */
    __HAL_IRDA_CLEAR_FLAG(hirda, IRDA_FLAG_TC);
    
    /* Process Unlocked */
    __HAL_UNLOCK(hirda);

    /* Enable the DMA transfer for transmit request by setting the DMAT bit
    in the USART CR3 register */
    SET_BIT(hirda->Instance->CR3, USART_CR3_DMAT);

    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;
  }
}

/**
  * @brief  Receives an amount of data in non blocking mode. 
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  pData Pointer to data buffer
  * @param  Size Amount of data to be received
  * @note   When the IRDA parity is enabled (PCE = 1) the data received contain the parity bit.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_Receive_DMA(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size)
{
  uint32_t *tmp;
  
  /* Check that a Rx process is not already ongoing */
  if(hirda->RxState == HAL_IRDA_STATE_READY) 
  {
    if((pData == NULL) || (Size == 0)) 
    {
      return HAL_ERROR;
    }

    /* Process Locked */
    __HAL_LOCK(hirda);

    hirda->pRxBuffPtr = pData;
    hirda->RxXferSize = Size;   
    hirda->ErrorCode = HAL_IRDA_ERROR_NONE; 
    hirda->RxState = HAL_IRDA_STATE_BUSY_RX;

    /* Set the IRDA DMA transfer complete callback */
    hirda->hdmarx->XferCpltCallback = IRDA_DMAReceiveCplt;

    /* Set the IRDA DMA half transfer complete callback */
    hirda->hdmarx->XferHalfCpltCallback = IRDA_DMAReceiveHalfCplt;

    /* Set the DMA error callback */
    hirda->hdmarx->XferErrorCallback = IRDA_DMAError;

    /* Set the DMA abort callback */
    hirda->hdmarx->XferAbortCallback = NULL;

    /* Enable the DMA Stream */
    tmp = (uint32_t*)&pData;
    HAL_DMA_Start_IT(hirda->hdmarx, (uint32_t)&hirda->Instance->DR, *(uint32_t*)tmp, Size);
	
    /* Clear the Overrun flag just before enabling the DMA Rx request: can be mandatory for the second transfer */
    __HAL_IRDA_CLEAR_OREFLAG(hirda);

    /* Process Unlocked */
    __HAL_UNLOCK(hirda);

    /* Enable the IRDA Parity Error Interrupt */
    SET_BIT(hirda->Instance->CR1, USART_CR1_PEIE);

    /* Enable the IRDA Error Interrupt: (Frame error, noise error, overrun error) */
    SET_BIT(hirda->Instance->CR3, USART_CR3_EIE);

    /* Enable the DMA transfer for the receiver request by setting the DMAR bit 
    in the USART CR3 register */
    SET_BIT(hirda->Instance->CR3, USART_CR3_DMAR);

    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;
  }
}
    
/**
  * @brief Pauses the DMA Transfer.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_DMAPause(IRDA_HandleTypeDef *hirda)
{
  uint32_t dmarequest = 0x00U;

  /* Process Locked */
  __HAL_LOCK(hirda);
  
  dmarequest = HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAT);
  if((hirda->gState == HAL_IRDA_STATE_BUSY_TX) && dmarequest)
  {
    /* Disable the IRDA DMA Tx request */
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAT);
  }
  
  dmarequest = HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR);
  if((hirda->RxState == HAL_IRDA_STATE_BUSY_RX) && dmarequest)
  {
    /* Disable PE and ERR (Frame error, noise error, overrun error) interrupts */
    CLEAR_BIT(hirda->Instance->CR1, USART_CR1_PEIE);
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);
    
    /* Disable the IRDA DMA Rx request */
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAR);
  }
  
  /* Process Unlocked */
  __HAL_UNLOCK(hirda);
  
  return HAL_OK;
}

/**
  * @brief Resumes the DMA Transfer.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_DMAResume(IRDA_HandleTypeDef *hirda)
{
  /* Process Locked */
  __HAL_LOCK(hirda);
  
  if(hirda->gState == HAL_IRDA_STATE_BUSY_TX)
  {
    /* Enable the IRDA DMA Tx request */
    SET_BIT(hirda->Instance->CR3, USART_CR3_DMAT);
  }
  if(hirda->RxState == HAL_IRDA_STATE_BUSY_RX)
  {
    /* Clear the Overrun flag before resuming the Rx transfer */
    __HAL_IRDA_CLEAR_OREFLAG(hirda);
    
    /* Reenable PE and ERR (Frame error, noise error, overrun error) interrupts */
    SET_BIT(hirda->Instance->CR1, USART_CR1_PEIE);
    SET_BIT(hirda->Instance->CR3, USART_CR3_EIE);
    
    /* Enable the IRDA DMA Rx request */
    SET_BIT(hirda->Instance->CR3, USART_CR3_DMAR);
  }
  
  /* Process Unlocked */
  __HAL_UNLOCK(hirda);
  
  return HAL_OK;
}

/**
  * @brief Stops the DMA Transfer.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
HAL_StatusTypeDef HAL_IRDA_DMAStop(IRDA_HandleTypeDef *hirda)
{
  uint32_t dmarequest = 0x00U;
  /* The Lock is not implemented on this API to allow the user application
  to call the HAL IRDA API under callbacks HAL_IRDA_TxCpltCallback() / HAL_IRDA_RxCpltCallback():
  when calling HAL_DMA_Abort() API the DMA TX/RX Transfer complete interrupt is generated
  and the correspond call back is executed HAL_IRDA_TxCpltCallback() / HAL_IRDA_RxCpltCallback()
  */
  
  /* Stop IRDA DMA Tx request if ongoing */
  dmarequest = HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAT);
  if((hirda->gState == HAL_IRDA_STATE_BUSY_TX) && dmarequest)
  {
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAT);
    
    /* Abort the IRDA DMA Tx channel */
    if(hirda->hdmatx != NULL)
    {
      HAL_DMA_Abort(hirda->hdmatx);
    }
    IRDA_EndTxTransfer(hirda);
  }

  /* Stop IRDA DMA Rx request if ongoing */
  dmarequest = HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR);
  if((hirda->RxState == HAL_IRDA_STATE_BUSY_RX) && dmarequest)
  {
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAR);
    
    /* Abort the IRDA DMA Rx channel */
    if(hirda->hdmarx != NULL)
    {
      HAL_DMA_Abort(hirda->hdmarx);
    }
    IRDA_EndRxTransfer(hirda);
  }
  return HAL_OK;
}

/**
  * @brief  Abort ongoing transfers (blocking mode).
  * @param  hirda IRDA handle.
  * @note   This procedure could be used for aborting any ongoing transfer started in Interrupt or DMA mode. 
  *         This procedure performs following operations :
  *           - Disable PPP Interrupts
  *           - Disable the DMA transfer in the peripheral register (if enabled)
  *           - Abort DMA transfer by calling HAL_DMA_Abort (in case of transfer in DMA mode)
  *           - Set handle State to READY
  * @note   This procedure is executed in blocking mode : when exiting function, Abort is considered as completed.
  * @retval HAL status
*/
HAL_StatusTypeDef HAL_IRDA_Abort(IRDA_HandleTypeDef *hirda)
{
  /* Disable TXEIE, TCIE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */
  CLEAR_BIT(hirda->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE));
  CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);
  
  /* Disable the IRDA DMA Tx request if enabled */
  if(HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAT))
  {
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAT);

    /* Abort the IRDA DMA Tx channel : use blocking DMA Abort API (no callback) */
    if(hirda->hdmatx != NULL)
    {
      /* Set the IRDA DMA Abort callback to Null. 
         No call back execution at end of DMA abort procedure */
      hirda->hdmatx->XferAbortCallback = NULL;

      HAL_DMA_Abort(hirda->hdmatx);
    }
  }

  /* Disable the IRDA DMA Rx request if enabled */
  if(HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR))
  {
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAR);

    /* Abort the IRDA DMA Rx channel : use blocking DMA Abort API (no callback) */
    if(hirda->hdmarx != NULL)
    {
      /* Set the IRDA DMA Abort callback to Null. 
         No call back execution at end of DMA abort procedure */
      hirda->hdmarx->XferAbortCallback = NULL;

      HAL_DMA_Abort(hirda->hdmarx);
    }
  }

  /* Reset Tx and Rx transfer counters */
  hirda->TxXferCount = 0x00U;
  hirda->RxXferCount = 0x00U;

  /* Reset ErrorCode */
  hirda->ErrorCode = HAL_IRDA_ERROR_NONE;

  /* Restore hirda->RxState and hirda->gState to Ready */
  hirda->RxState = HAL_IRDA_STATE_READY;
  hirda->gState = HAL_IRDA_STATE_READY;

  return HAL_OK;
}

/**
  * @brief  Abort ongoing Transmit transfer (blocking mode).
  * @param  hirda IRDA handle.
  * @note   This procedure could be used for aborting any ongoing transfer started in Interrupt or DMA mode. 
  *         This procedure performs following operations :
  *           - Disable PPP Interrupts
  *           - Disable the DMA transfer in the peripheral register (if enabled)
  *           - Abort DMA transfer by calling HAL_DMA_Abort (in case of transfer in DMA mode)
  *           - Set handle State to READY
  * @note   This procedure is executed in blocking mode : when exiting function, Abort is considered as completed.
  * @retval HAL status
*/
HAL_StatusTypeDef HAL_IRDA_AbortTransmit(IRDA_HandleTypeDef *hirda)
{
  /* Disable TXEIE and TCIE interrupts */
  CLEAR_BIT(hirda->Instance->CR1, (USART_CR1_TXEIE | USART_CR1_TCIE));

  /* Disable the IRDA DMA Tx request if enabled */
  if(HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAT))
  {
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAT);

    /* Abort the IRDA DMA Tx channel : use blocking DMA Abort API (no callback) */
    if(hirda->hdmatx != NULL)
    {
      /* Set the IRDA DMA Abort callback to Null. 
         No call back execution at end of DMA abort procedure */
      hirda->hdmatx->XferAbortCallback = NULL;

      HAL_DMA_Abort(hirda->hdmatx);
    }
  }

  /* Reset Tx transfer counter */
  hirda->TxXferCount = 0x00U;

  /* Restore hirda->gState to Ready */
  hirda->gState = HAL_IRDA_STATE_READY;

  return HAL_OK;
}

/**
  * @brief  Abort ongoing Receive transfer (blocking mode).
  * @param  hirda IRDA handle.
  * @note   This procedure could be used for aborting any ongoing transfer started in Interrupt or DMA mode. 
  *         This procedure performs following operations :
  *           - Disable PPP Interrupts
  *           - Disable the DMA transfer in the peripheral register (if enabled)
  *           - Abort DMA transfer by calling HAL_DMA_Abort (in case of transfer in DMA mode)
  *           - Set handle State to READY
  * @note   This procedure is executed in blocking mode : when exiting function, Abort is considered as completed.
  * @retval HAL status
*/
HAL_StatusTypeDef HAL_IRDA_AbortReceive(IRDA_HandleTypeDef *hirda)
{
  /* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */
  CLEAR_BIT(hirda->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE));
  CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);

  /* Disable the IRDA DMA Rx request if enabled */
  if(HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR))
  {
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAR);

    /* Abort the IRDA DMA Rx channel : use blocking DMA Abort API (no callback) */
    if(hirda->hdmarx != NULL)
    {
      /* Set the IRDA DMA Abort callback to Null. 
         No call back execution at end of DMA abort procedure */
      hirda->hdmarx->XferAbortCallback = NULL;

      HAL_DMA_Abort(hirda->hdmarx);
    }
  }

  /* Reset Rx transfer counter */
  hirda->RxXferCount = 0x00U;

  /* Restore hirda->RxState to Ready */
  hirda->RxState = HAL_IRDA_STATE_READY;

  return HAL_OK;
}

/**
  * @brief  Abort ongoing transfers (Interrupt mode).
  * @param  hirda IRDA handle.
  * @note   This procedure could be used for aborting any ongoing transfer started in Interrupt or DMA mode. 
  *         This procedure performs following operations :
  *           - Disable PPP Interrupts
  *           - Disable the DMA transfer in the peripheral register (if enabled)
  *           - Abort DMA transfer by calling HAL_DMA_Abort_IT (in case of transfer in DMA mode)
  *           - Set handle State to READY
  *           - At abort completion, call user abort complete callback
  * @note   This procedure is executed in Interrupt mode, meaning that abort procedure could be
  *         considered as completed only when user abort complete callback is executed (not when exiting function).
  * @retval HAL status
*/
HAL_StatusTypeDef HAL_IRDA_Abort_IT(IRDA_HandleTypeDef *hirda)
{
    uint32_t AbortCplt = 1U;

  /* Disable TXEIE, TCIE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */
  CLEAR_BIT(hirda->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE));
  CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);

  /* If DMA Tx and/or DMA Rx Handles are associated to IRDA Handle, DMA Abort complete callbacks should be initialised
     before any call to DMA Abort functions */
  /* DMA Tx Handle is valid */
  if(hirda->hdmatx != NULL)
  {
    /* Set DMA Abort Complete callback if IRDA DMA Tx request if enabled.
       Otherwise, set it to NULL */
    if(HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAT))
    {
      hirda->hdmatx->XferAbortCallback = IRDA_DMATxAbortCallback;
    }
    else
    {
      hirda->hdmatx->XferAbortCallback = NULL;
    }
  }
  /* DMA Rx Handle is valid */
  if(hirda->hdmarx != NULL)
  {
    /* Set DMA Abort Complete callback if IRDA DMA Rx request if enabled.
       Otherwise, set it to NULL */
    if(HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR))
    {
      hirda->hdmarx->XferAbortCallback = IRDA_DMARxAbortCallback;
    }
    else
    {
      hirda->hdmarx->XferAbortCallback = NULL;
    }
  }

  /* Disable the IRDA DMA Tx request if enabled */
  if(HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAT))
  {
    /* Disable DMA Tx at IRDA level */
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAT);

    /* Abort the IRDA DMA Tx channel : use non blocking DMA Abort API (callback) */
    if(hirda->hdmatx != NULL)
    {
      /* IRDA Tx DMA Abort callback has already been initialised : 
         will lead to call HAL_IRDA_AbortCpltCallback() at end of DMA abort procedure */

      /* Abort DMA TX */
      if(HAL_DMA_Abort_IT(hirda->hdmatx) != HAL_OK)
      {
        hirda->hdmatx->XferAbortCallback = NULL;
      }
      else
      {
        AbortCplt = 0x00U;
      }
    }
  }

  /* Disable the IRDA DMA Rx request if enabled */
  if(HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR))
  {
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAR);

    /* Abort the IRDA DMA Rx channel : use non blocking DMA Abort API (callback) */
    if(hirda->hdmarx != NULL)
    {
      /* IRDA Rx DMA Abort callback has already been initialised : 
         will lead to call HAL_IRDA_AbortCpltCallback() at end of DMA abort procedure */

      /* Abort DMA RX */
      if(HAL_DMA_Abort_IT(hirda->hdmarx) != HAL_OK)
      {
        hirda->hdmarx->XferAbortCallback = NULL;
        AbortCplt = 0x01U;
      }
      else
      {
        AbortCplt = 0x00U;
      }
    }
  }

  /* if no DMA abort complete callback execution is required => call user Abort Complete callback */
  if(AbortCplt == 0x01U)
  {
    /* Reset Tx and Rx transfer counters */
    hirda->TxXferCount = 0x00U; 
    hirda->RxXferCount = 0x00U;

    /* Reset ErrorCode */
    hirda->ErrorCode = HAL_IRDA_ERROR_NONE;

    /* Restore hirda->gState and hirda->RxState to Ready */
    hirda->gState  = HAL_IRDA_STATE_READY;
    hirda->RxState = HAL_IRDA_STATE_READY;

    /* As no DMA to be aborted, call directly user Abort complete callback */
    HAL_IRDA_AbortCpltCallback(hirda);
  }

  return HAL_OK;
}

/**
  * @brief  Abort ongoing Transmit transfer (Interrupt mode).
  * @param  hirda IRDA handle.
  * @note   This procedure could be used for aborting any ongoing transfer started in Interrupt or DMA mode. 
  *         This procedure performs following operations :
  *           - Disable PPP Interrupts
  *           - Disable the DMA transfer in the peripheral register (if enabled)
  *           - Abort DMA transfer by calling HAL_DMA_Abort_IT (in case of transfer in DMA mode)
  *           - Set handle State to READY
  *           - At abort completion, call user abort complete callback
  * @note   This procedure is executed in Interrupt mode, meaning that abort procedure could be
  *         considered as completed only when user abort complete callback is executed (not when exiting function).
  * @retval HAL status
*/
HAL_StatusTypeDef HAL_IRDA_AbortTransmit_IT(IRDA_HandleTypeDef *hirda)
{
  /* Disable TXEIE and TCIE interrupts */
  CLEAR_BIT(hirda->Instance->CR1, (USART_CR1_TXEIE | USART_CR1_TCIE));

  /* Disable the IRDA DMA Tx request if enabled */
  if(HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAT))
  {
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAT);

    /* Abort the IRDA DMA Tx channel : use blocking DMA Abort API (no callback) */
    if(hirda->hdmatx != NULL)
    {
      /* Set the IRDA DMA Abort callback : 
         will lead to call HAL_IRDA_AbortCpltCallback() at end of DMA abort procedure */
      hirda->hdmatx->XferAbortCallback = IRDA_DMATxOnlyAbortCallback;

      /* Abort DMA TX */
      if(HAL_DMA_Abort_IT(hirda->hdmatx) != HAL_OK)
      {
        /* Call Directly hirda->hdmatx->XferAbortCallback function in case of error */
        hirda->hdmatx->XferAbortCallback(hirda->hdmatx);
      }
    }
    else
    {
      /* Reset Tx transfer counter */
      hirda->TxXferCount = 0x00U;

      /* Restore hirda->gState to Ready */
      hirda->gState = HAL_IRDA_STATE_READY;
      
      /* As no DMA to be aborted, call directly user Abort complete callback */
      HAL_IRDA_AbortTransmitCpltCallback(hirda);
    }
  }
  else
  {
    /* Reset Tx transfer counter */
    hirda->TxXferCount = 0x00U;

    /* Restore hirda->gState to Ready */
    hirda->gState = HAL_IRDA_STATE_READY;

    /* As no DMA to be aborted, call directly user Abort complete callback */
    HAL_IRDA_AbortTransmitCpltCallback(hirda);
  }

  return HAL_OK;
}

/**
  * @brief  Abort ongoing Receive transfer (Interrupt mode).
  * @param  hirda IRDA handle.
  * @note   This procedure could be used for aborting any ongoing transfer started in Interrupt or DMA mode. 
  *         This procedure performs following operations :
  *           - Disable PPP Interrupts
  *           - Disable the DMA transfer in the peripheral register (if enabled)
  *           - Abort DMA transfer by calling HAL_DMA_Abort_IT (in case of transfer in DMA mode)
  *           - Set handle State to READY
  *           - At abort completion, call user abort complete callback
  * @note   This procedure is executed in Interrupt mode, meaning that abort procedure could be
  *         considered as completed only when user abort complete callback is executed (not when exiting function).
  * @retval HAL status
*/
HAL_StatusTypeDef HAL_IRDA_AbortReceive_IT(IRDA_HandleTypeDef *hirda)
{
  /* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */
  CLEAR_BIT(hirda->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE));
  CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);

  /* Disable the IRDA DMA Rx request if enabled */
  if(HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR))
  {
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAR);

    /* Abort the IRDA DMA Rx channel : use blocking DMA Abort API (no callback) */
    if(hirda->hdmarx != NULL)
    {
      /* Set the IRDA DMA Abort callback : 
         will lead to call HAL_IRDA_AbortCpltCallback() at end of DMA abort procedure */
      hirda->hdmarx->XferAbortCallback = IRDA_DMARxOnlyAbortCallback;

      /* Abort DMA RX */
      if(HAL_DMA_Abort_IT(hirda->hdmarx) != HAL_OK)
      {
        /* Call Directly hirda->hdmarx->XferAbortCallback function in case of error */
        hirda->hdmarx->XferAbortCallback(hirda->hdmarx);
      }
    }
    else
    {
      /* Reset Rx transfer counter */
      hirda->RxXferCount = 0x00U;

      /* Restore hirda->RxState to Ready */
      hirda->RxState = HAL_IRDA_STATE_READY;

      /* As no DMA to be aborted, call directly user Abort complete callback */
      HAL_IRDA_AbortReceiveCpltCallback(hirda);
    }
  }
  else
  {
    /* Reset Rx transfer counter */
    hirda->RxXferCount = 0x00U;

    /* Restore hirda->RxState to Ready */
    hirda->RxState = HAL_IRDA_STATE_READY;

    /* As no DMA to be aborted, call directly user Abort complete callback */
    HAL_IRDA_AbortReceiveCpltCallback(hirda);
  }

  return HAL_OK;
}

/**
  * @brief  This function handles IRDA interrupt request.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
void HAL_IRDA_IRQHandler(IRDA_HandleTypeDef *hirda)
{
   uint32_t isrflags   = READ_REG(hirda->Instance->SR);
   uint32_t cr1its     = READ_REG(hirda->Instance->CR1);
   uint32_t cr3its     = READ_REG(hirda->Instance->CR3);
   uint32_t errorflags = 0x00U;
   uint32_t dmarequest = 0x00U;

  /* If no error occurs */
  errorflags = (isrflags & (uint32_t)(USART_SR_PE | USART_SR_FE | USART_SR_ORE | USART_SR_NE));
  if(errorflags == RESET)
  {
    /* IRDA in mode Receiver -----------------------------------------------*/
    if(((isrflags & USART_SR_RXNE) != RESET) && ((cr1its & USART_CR1_RXNEIE) != RESET))
    {
      IRDA_Receive_IT(hirda);
      return;
    }
  }  

  /* If some errors occur */
  if((errorflags != RESET) && (((cr3its & USART_CR3_EIE) != RESET) || ((cr1its & (USART_CR1_RXNEIE | USART_CR1_PEIE)) != RESET)))
  {
    /* IRDA parity error interrupt occurred -------------------------------*/
    if(((isrflags & USART_SR_PE) != RESET) && ((cr1its & USART_CR1_PEIE) != RESET))
    {
      hirda->ErrorCode |= HAL_IRDA_ERROR_PE;
    }

    /* IRDA noise error interrupt occurred --------------------------------*/
    if(((isrflags & USART_SR_NE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET))
    {
      hirda->ErrorCode |= HAL_IRDA_ERROR_NE;
    }

    /* IRDA frame error interrupt occurred --------------------------------*/
    if(((isrflags & USART_SR_FE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET))
    {
      hirda->ErrorCode |= HAL_IRDA_ERROR_FE;
    }

    /* IRDA Over-Run interrupt occurred -----------------------------------*/
    if(((isrflags & USART_SR_ORE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET))
    { 
      hirda->ErrorCode |= HAL_IRDA_ERROR_ORE;
    }
    /* Call IRDA Error Call back function if need be -----------------------*/ 
    if(hirda->ErrorCode != HAL_IRDA_ERROR_NONE)
    {
      /* IRDA in mode Receiver ---------------------------------------------*/
      if(((isrflags & USART_SR_RXNE) != RESET) && ((cr1its & USART_CR1_RXNEIE) != RESET))
      {
        IRDA_Receive_IT(hirda);
      }

      dmarequest = HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR);
      /* If Overrun error occurs, or if any error occurs in DMA mode reception,
         consider error as blocking */
      if(((hirda->ErrorCode & HAL_IRDA_ERROR_ORE) != RESET) || dmarequest)
      {
        /* Blocking error : transfer is aborted
           Set the IRDA state ready to be able to start again the process,
           Disable Rx Interrupts, and disable Rx DMA request, if ongoing */
        IRDA_EndRxTransfer(hirda);

        /* Disable the IRDA DMA Rx request if enabled */
        if(HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR))
        {
          CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAR);

          /* Abort the IRDA DMA Rx channel */
          if(hirda->hdmarx != NULL)
          {
            /* Set the IRDA DMA Abort callback : 
            will lead to call HAL_IRDA_ErrorCallback() at end of DMA abort procedure */
            hirda->hdmarx->XferAbortCallback = IRDA_DMAAbortOnError;

            if(HAL_DMA_Abort_IT(hirda->hdmarx) != HAL_OK)
            {
              /* Call Directly XferAbortCallback function in case of error */
              hirda->hdmarx->XferAbortCallback(hirda->hdmarx);
            }
          }
          else
          {
            /* Call user error callback */
            HAL_IRDA_ErrorCallback(hirda);
          }
        }
        else
        {
          /* Call user error callback */
          HAL_IRDA_ErrorCallback(hirda);
        }
      }
      else
      {
        /* Non Blocking error : transfer could go on. 
           Error is notified to user through user error callback */
        HAL_IRDA_ErrorCallback(hirda);
        hirda->ErrorCode = HAL_IRDA_ERROR_NONE;
      }
    }
    return;
  } /* End if some error occurs */

  /* IRDA in mode Transmitter ------------------------------------------------*/
  if(((isrflags & USART_SR_TXE) != RESET) && ((cr1its & USART_CR1_TXEIE) != RESET))
  {
    IRDA_Transmit_IT(hirda);
    return;
  }

  /* IRDA in mode Transmitter end --------------------------------------------*/
  if(((isrflags & USART_SR_TC) != RESET) && ((cr1its & USART_CR1_TCIE) != RESET))
  {
    IRDA_EndTransmit_IT(hirda);
    return;
  }
}

/**
  * @brief  End ongoing Tx transfer on IRDA peripheral (following error detection or Transmit completion).
  * @param  hirda IRDA handle.
  * @retval None
  */
static void IRDA_EndTxTransfer(IRDA_HandleTypeDef *hirda)
{
  /* Disable TXEIE and TCIE interrupts */
  CLEAR_BIT(hirda->Instance->CR1, (USART_CR1_TXEIE | USART_CR1_TCIE));

  /* At end of Tx process, restore hirda->gState to Ready */
  hirda->gState = HAL_IRDA_STATE_READY;
}

/**
  * @brief  End ongoing Rx transfer on IRDA peripheral (following error detection or Reception completion).
  * @param  hirda IRDA handle.
  * @retval None
  */
static void IRDA_EndRxTransfer(IRDA_HandleTypeDef *hirda)
{
  /* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */
  CLEAR_BIT(hirda->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE));
  CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);

  /* At end of Rx process, restore hirda->RxState to Ready */
  hirda->RxState = HAL_IRDA_STATE_READY;
}

/**
  * @brief  DMA IRDA communication abort callback, when initiated by HAL services on Error
  *         (To be called at end of DMA Abort procedure following error occurrence).
  * @param  hdma DMA handle.
  * @retval None
  */
static void IRDA_DMAAbortOnError(DMA_HandleTypeDef *hdma)
{
  IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
  hirda->RxXferCount = 0x00U;
  hirda->TxXferCount = 0x00U;

  HAL_IRDA_ErrorCallback(hirda);
}

/**
  * @brief  DMA IRDA Tx communication abort callback, when initiated by user
  *         (To be called at end of DMA Tx Abort procedure following user abort request).
  * @note   When this callback is executed, User Abort complete call back is called only if no
  *         Abort still ongoing for Rx DMA Handle.
  * @param  hdma DMA handle.
  * @retval None
  */
static void IRDA_DMATxAbortCallback(DMA_HandleTypeDef *hdma)
{
  IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
  
  hirda->hdmatx->XferAbortCallback = NULL;

  /* Check if an Abort process is still ongoing */
  if(hirda->hdmarx != NULL)
  {
    if(hirda->hdmarx->XferAbortCallback != NULL)
    {
      return;
    }
  }
  
  /* No Abort process still ongoing : All DMA channels are aborted, call user Abort Complete callback */
  hirda->TxXferCount = 0x00U;
  hirda->RxXferCount = 0x00U;

  /* Reset ErrorCode */
  hirda->ErrorCode = HAL_IRDA_ERROR_NONE;

  /* Restore hirda->gState and hirda->RxState to Ready */
  hirda->gState  = HAL_IRDA_STATE_READY;
  hirda->RxState = HAL_IRDA_STATE_READY;

  /* Call user Abort complete callback */
  HAL_IRDA_AbortCpltCallback(hirda);
}

/**
  * @brief  DMA IRDA Rx communication abort callback, when initiated by user
  *         (To be called at end of DMA Rx Abort procedure following user abort request).
  * @note   When this callback is executed, User Abort complete call back is called only if no
  *         Abort still ongoing for Tx DMA Handle.
  * @param  hdma DMA handle.
  * @retval None
  */
static void IRDA_DMARxAbortCallback(DMA_HandleTypeDef *hdma)
{
  IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
  
  hirda->hdmarx->XferAbortCallback = NULL;

  /* Check if an Abort process is still ongoing */
  if(hirda->hdmatx != NULL)
  {
    if(hirda->hdmatx->XferAbortCallback != NULL)
    {
      return;
    }
  }
  
  /* No Abort process still ongoing : All DMA channels are aborted, call user Abort Complete callback */
  hirda->TxXferCount = 0x00U;
  hirda->RxXferCount = 0x00U;

  /* Reset ErrorCode */
  hirda->ErrorCode = HAL_IRDA_ERROR_NONE;

  /* Restore hirda->gState and hirda->RxState to Ready */
  hirda->gState  = HAL_IRDA_STATE_READY;
  hirda->RxState = HAL_IRDA_STATE_READY;

  /* Call user Abort complete callback */
  HAL_IRDA_AbortCpltCallback(hirda);
}

/**
  * @brief  DMA IRDA Tx communication abort callback, when initiated by user by a call to
  *         HAL_IRDA_AbortTransmit_IT API (Abort only Tx transfer)
  *         (This callback is executed at end of DMA Tx Abort procedure following user abort request,
  *         and leads to user Tx Abort Complete callback execution).
  * @param  hdma DMA handle.
  * @retval None
  */
static void IRDA_DMATxOnlyAbortCallback(DMA_HandleTypeDef *hdma)
{
  IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;

  hirda->TxXferCount = 0x00U;

  /* Restore hirda->gState to Ready */
  hirda->gState = HAL_IRDA_STATE_READY;

  /* Call user Abort complete callback */
  HAL_IRDA_AbortTransmitCpltCallback(hirda);
}

/**
  * @brief  DMA IRDA Rx communication abort callback, when initiated by user by a call to
  *         HAL_IRDA_AbortReceive_IT API (Abort only Rx transfer)
  *         (This callback is executed at end of DMA Rx Abort procedure following user abort request,
  *         and leads to user Rx Abort Complete callback execution).
  * @param  hdma DMA handle.
  * @retval None
  */
static void IRDA_DMARxOnlyAbortCallback(DMA_HandleTypeDef *hdma)
{
  IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;

  hirda->RxXferCount = 0x00U;

  /* Restore hirda->RxState to Ready */
  hirda->RxState = HAL_IRDA_STATE_READY;

  /* Call user Abort complete callback */
  HAL_IRDA_AbortReceiveCpltCallback(hirda);
}

/**
  * @brief  Tx Transfer complete callbacks.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
__weak void HAL_IRDA_TxCpltCallback(IRDA_HandleTypeDef *hirda)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hirda);
  /* NOTE : This function Should not be modified, when the callback is needed,
  the HAL_IRDA_TxCpltCallback could be implemented in the user file
  */ 
}

/**
  * @brief  Tx Half Transfer completed callbacks.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified USART module.
  * @retval None
  */
__weak void HAL_IRDA_TxHalfCpltCallback(IRDA_HandleTypeDef *hirda)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hirda);
  /* NOTE: This function Should not be modified, when the callback is needed,
  the HAL_IRDA_TxHalfCpltCallback could be implemented in the user file
  */
}

/**
  * @brief  Rx Transfer complete callbacks.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
__weak void HAL_IRDA_RxCpltCallback(IRDA_HandleTypeDef *hirda)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hirda);
  /* NOTE : This function Should not be modified, when the callback is needed,
  the HAL_IRDA_RxCpltCallback could be implemented in the user file
  */
}

/**
  * @brief  Rx Half Transfer complete callbacks.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
__weak void HAL_IRDA_RxHalfCpltCallback(IRDA_HandleTypeDef *hirda)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hirda);
  /* NOTE : This function Should not be modified, when the callback is needed,
  the HAL_IRDA_RxHalfCpltCallback could be implemented in the user file
  */
}

/**
  * @brief IRDA error callbacks.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
__weak void HAL_IRDA_ErrorCallback(IRDA_HandleTypeDef *hirda)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hirda);
  /* NOTE : This function Should not be modified, when the callback is needed,
  the HAL_IRDA_ErrorCallback could be implemented in the user file
  */ 
}

/**
  * @brief  IRDA Abort Complete callback.
  * @param  hirda IRDA handle.
  * @retval None
  */
__weak void HAL_IRDA_AbortCpltCallback(IRDA_HandleTypeDef *hirda)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hirda);

  /* NOTE : This function should not be modified, when the callback is needed,
            the HAL_IRDA_AbortCpltCallback can be implemented in the user file.
   */
}

/**
  * @brief  IRDA Abort Transmit Complete callback.
  * @param  hirda IRDA handle.
  * @retval None
  */
__weak void HAL_IRDA_AbortTransmitCpltCallback(IRDA_HandleTypeDef *hirda)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hirda);

  /* NOTE : This function should not be modified, when the callback is needed,
            the HAL_IRDA_AbortTransmitCpltCallback can be implemented in the user file.
   */
}

/**
  * @brief  IRDA Abort ReceiveComplete callback.
  * @param  hirda IRDA handle.
  * @retval None
  */
__weak void HAL_IRDA_AbortReceiveCpltCallback(IRDA_HandleTypeDef *hirda)
{
  /* Prevent unused argument(s) compilation warning */
  UNUSED(hirda);

  /* NOTE : This function should not be modified, when the callback is needed,
            the HAL_IRDA_AbortReceiveCpltCallback can be implemented in the user file.
   */
}

/**
  * @}
  */

/** @defgroup IRDA_Exported_Functions_Group3 Peripheral State and Errors functions 
  *  @brief   IRDA State and Errors functions 
  *
@verbatim   
  ==============================================================================
                  ##### Peripheral State and Errors functions #####
  ==============================================================================  
  [..]
    This subsection provides a set of functions allowing to return the State of IrDA 
    communication process and also return Peripheral Errors occurred during communication process
     (+) HAL_IRDA_GetState() API can be helpful to check in run-time the state of the IrDA peripheral.
     (+) HAL_IRDA_GetError() check in run-time errors that could be occurred during communication. 
     
@endverbatim
  * @{
  */

/**
  * @brief  Returns the IRDA state.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL state
  */
HAL_IRDA_StateTypeDef HAL_IRDA_GetState(IRDA_HandleTypeDef *hirda)
{
  uint32_t temp1 = 0x00U, temp2 = 0x00U;
  temp1 = hirda->gState;
  temp2 = hirda->RxState;
  
  return (HAL_IRDA_StateTypeDef)(temp1 | temp2);
}

/**
  * @brief  Return the IARDA error code
  * @param  hirda  pointer to a IRDA_HandleTypeDef structure that contains
  *              the configuration information for the specified IRDA.
  * @retval IRDA Error Code
  */
uint32_t HAL_IRDA_GetError(IRDA_HandleTypeDef *hirda)
{
  return hirda->ErrorCode;
}

/**
  * @}
  */
  
/**
  * @brief  DMA IRDA transmit process complete callback. 
  * @param  hdma  DMA handle
  * @retval None
  */
static void IRDA_DMATransmitCplt(DMA_HandleTypeDef *hdma)
{
  IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
  /* DMA Normal mode */
  if((hdma->Instance->CR & DMA_SxCR_CIRC) == 0U)
  {
    hirda->TxXferCount = 0U;
    
    /* Disable the DMA transfer for transmit request by setting the DMAT bit
    in the IRDA CR3 register */
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAT);
    
    /* Enable the IRDA Transmit Complete Interrupt */
    SET_BIT(hirda->Instance->CR1, USART_CR1_TCIE);
  }
  /* DMA Circular mode */
  else
  {
    HAL_IRDA_TxCpltCallback(hirda);
  }
}

/**
  * @brief DMA IRDA receive process half complete callback 
  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
  *                the configuration information for the specified DMA module.
  * @retval None
  */
static void IRDA_DMATransmitHalfCplt(DMA_HandleTypeDef *hdma)
{
  IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
  
  HAL_IRDA_TxHalfCpltCallback(hirda); 
}

/**
  * @brief  DMA IRDA receive process complete callback. 
  * @param  hdma DMA handle
  * @retval None
  */
static void IRDA_DMAReceiveCplt(DMA_HandleTypeDef *hdma)   
{
  IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
  /* DMA Normal mode */
  if((hdma->Instance->CR & DMA_SxCR_CIRC) == 0U)
  {
    hirda->RxXferCount = 0U;
    
    /* Disable PE and ERR (Frame error, noise error, overrun error) interrupts */
    CLEAR_BIT(hirda->Instance->CR1, USART_CR1_PEIE);
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);
    
    /* Disable the DMA transfer for the receiver request by setting the DMAR bit 
    in the IRDA CR3 register */
    CLEAR_BIT(hirda->Instance->CR3, USART_CR3_DMAR);
    
    /* At end of Rx process, restore hirda->RxState to Ready */
    hirda->RxState = HAL_IRDA_STATE_READY;
  }
  
  HAL_IRDA_RxCpltCallback(hirda);
}

/**
  * @brief DMA IRDA receive process half complete callback 
  * @param  hdma pointer to a DMA_HandleTypeDef structure that contains
  *                the configuration information for the specified DMA module.
  * @retval None
  */
static void IRDA_DMAReceiveHalfCplt(DMA_HandleTypeDef *hdma)
{
  IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
  HAL_IRDA_RxHalfCpltCallback(hirda); 
}

/**
  * @brief  DMA IRDA communication error callback.
  * @param  hdma DMA handle
  * @retval None
  */
static void IRDA_DMAError(DMA_HandleTypeDef *hdma)
{
  uint32_t dmarequest = 0x00U;
  IRDA_HandleTypeDef* hirda = ( IRDA_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
  
  /* Stop IRDA DMA Tx request if ongoing */
  dmarequest = HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAT);
  if((hirda->gState == HAL_IRDA_STATE_BUSY_TX) && dmarequest)
  {
    hirda->TxXferCount = 0U;
    IRDA_EndTxTransfer(hirda);
  }

  /* Stop IRDA DMA Rx request if ongoing */
  dmarequest = HAL_IS_BIT_SET(hirda->Instance->CR3, USART_CR3_DMAR);
  if((hirda->RxState == HAL_IRDA_STATE_BUSY_RX) && dmarequest)
  {
    hirda->RxXferCount = 0U;
    IRDA_EndRxTransfer(hirda);
  }
  
  hirda->ErrorCode |= HAL_IRDA_ERROR_DMA; 
  
  HAL_IRDA_ErrorCallback(hirda);
}

/**
  * @brief  This function handles IRDA Communication Timeout.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @param  Flag specifies the IRDA flag to check.
  * @param  Status The new Flag status (SET or RESET).
  * @param  Tickstart Tick start value
  * @param  Timeout Timeout duration
  * @retval HAL status
  */
static HAL_StatusTypeDef IRDA_WaitOnFlagUntilTimeout(IRDA_HandleTypeDef *hirda, uint32_t Flag, FlagStatus Status, uint32_t Tickstart, uint32_t Timeout)
{
  /* Wait until flag is set */
  while((__HAL_IRDA_GET_FLAG(hirda, Flag) ? SET : RESET) == Status)
  {
    /* Check for the Timeout */
    if(Timeout != HAL_MAX_DELAY)
    {
      if((Timeout == 0U)||((HAL_GetTick() - Tickstart ) > Timeout))
      {
        /* Disable TXE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts for the interrupt process */
        CLEAR_BIT(hirda->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE | USART_CR1_TXEIE));
        CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);
        
        hirda->gState  = HAL_IRDA_STATE_READY;
        hirda->RxState = HAL_IRDA_STATE_READY;
        
        /* Process Unlocked */
        __HAL_UNLOCK(hirda);
        
        return HAL_TIMEOUT;
      }
    }
  }
  return HAL_OK;
}

 /**
  * @brief  Send an amount of data in non blocking mode. 
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
static HAL_StatusTypeDef IRDA_Transmit_IT(IRDA_HandleTypeDef *hirda)
{
  uint16_t* tmp;
  
  /* Check that a Tx process is ongoing */
  if(hirda->gState == HAL_IRDA_STATE_BUSY_TX)
  {
    if(hirda->Init.WordLength == IRDA_WORDLENGTH_9B)
    {
      tmp = (uint16_t*) hirda->pTxBuffPtr;
      hirda->Instance->DR = (uint16_t)(*tmp & (uint16_t)0x01FF);
      if(hirda->Init.Parity == IRDA_PARITY_NONE)
      {
        hirda->pTxBuffPtr += 2U;
      }
      else
      {
        hirda->pTxBuffPtr += 1U;
      }
    } 
    else
    {
      hirda->Instance->DR = (uint8_t)(*hirda->pTxBuffPtr++ & (uint8_t)0x00FF);
    }
    
    if(--hirda->TxXferCount == 0U)
    {
      /* Disable the IRDA Transmit Data Register Empty Interrupt */
      CLEAR_BIT(hirda->Instance->CR1, USART_CR1_TXEIE);
      
      /* Enable the IRDA Transmit Complete Interrupt */
      SET_BIT(hirda->Instance->CR1, USART_CR1_TCIE);
    }
    
    return HAL_OK;
  }
  else
  {
    return HAL_BUSY;
  }
}

/**
  * @brief  Wraps up transmission in non blocking mode.
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
static HAL_StatusTypeDef IRDA_EndTransmit_IT(IRDA_HandleTypeDef *hirda)
{
  /* Disable the IRDA Transmit Complete Interrupt */    
  CLEAR_BIT(hirda->Instance->CR1, USART_CR1_TCIE);
  
  /* Disable the IRDA Error Interrupt: (Frame error, noise error, overrun error) */
  CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);
  
  /* Tx process is ended, restore hirda->gState to Ready */
  hirda->gState = HAL_IRDA_STATE_READY;
  
  HAL_IRDA_TxCpltCallback(hirda);
  
  return HAL_OK;
}

/**
  * @brief  Receives an amount of data in non blocking mode. 
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval HAL status
  */
static HAL_StatusTypeDef IRDA_Receive_IT(IRDA_HandleTypeDef *hirda)
{
  uint16_t* tmp;
  uint16_t  uhdata;
  
  /* Check that a Rx process is ongoing */
  if(hirda->RxState == HAL_IRDA_STATE_BUSY_RX) 
  {
    uhdata = (uint16_t) READ_REG(hirda->Instance->DR);
    if(hirda->Init.WordLength == IRDA_WORDLENGTH_9B)
    {
      tmp = (uint16_t*) hirda->pRxBuffPtr;
      if(hirda->Init.Parity == IRDA_PARITY_NONE)
      {
        *tmp = (uint16_t)(uhdata & (uint16_t)0x01FF);
        hirda->pRxBuffPtr += 2U;
      }
      else
      {
        *tmp = (uint16_t)(uhdata & (uint16_t)0x00FF);
        hirda->pRxBuffPtr += 1U;
      }
    } 
    else
    {
      if(hirda->Init.Parity == IRDA_PARITY_NONE)
      {
        *hirda->pRxBuffPtr++ = (uint8_t)(uhdata & (uint8_t)0x00FF);
      }
      else
      {
        *hirda->pRxBuffPtr++ = (uint8_t)(uhdata & (uint8_t)0x007F);
      }
    }
    
    if(--hirda->RxXferCount == 0U)
    {
      /* Disable the IRDA Data Register not empty Interrupt */
      CLEAR_BIT(hirda->Instance->CR1, USART_CR1_RXNEIE);
      
      /* Disable the IRDA Parity Error Interrupt */
      CLEAR_BIT(hirda->Instance->CR1, USART_CR1_PEIE);
      
      /* Disable the IRDA Error Interrupt: (Frame error, noise error, overrun error) */
      CLEAR_BIT(hirda->Instance->CR3, USART_CR3_EIE);
      
      /* Rx process is completed, restore hirda->RxState to Ready */
      hirda->RxState = HAL_IRDA_STATE_READY;
      
      HAL_IRDA_RxCpltCallback(hirda);
      
      return HAL_OK;
    }
    return HAL_OK;
  }
  else
  {
    return HAL_BUSY; 
  }
}

/**
  * @brief  Configures the IRDA peripheral. 
  * @param  hirda pointer to a IRDA_HandleTypeDef structure that contains
  *                the configuration information for the specified IRDA module.
  * @retval None
  */
static void IRDA_SetConfig(IRDA_HandleTypeDef *hirda)
{
  /* Check the parameters */
  assert_param(IS_IRDA_INSTANCE(hirda->Instance));
  assert_param(IS_IRDA_BAUDRATE(hirda->Init.BaudRate));  
  assert_param(IS_IRDA_WORD_LENGTH(hirda->Init.WordLength));
  assert_param(IS_IRDA_PARITY(hirda->Init.Parity));
  assert_param(IS_IRDA_MODE(hirda->Init.Mode));
  
  /*-------------------------- IRDA CR2 Configuration ------------------------*/
  /* Clear STOP[13:12] bits */
  CLEAR_BIT(hirda->Instance->CR2, USART_CR2_STOP);
  
  /*-------------------------- USART CR1 Configuration -----------------------*/
  /* Clear M, PCE, PS, TE and RE bits */
  CLEAR_BIT(hirda->Instance->CR1, USART_CR1_M | USART_CR1_PCE | USART_CR1_PS | USART_CR1_TE | USART_CR1_RE);
  
  /* Configure the USART Word Length, Parity and mode: 
  Set the M bits according to hirda->Init.WordLength value 
  Set PCE and PS bits according to hirda->Init.Parity value
  Set TE and RE bits according to hirda->Init.Mode value */
  /* Write to USART CR1 */
  SET_BIT(hirda->Instance->CR1, (uint32_t)hirda->Init.WordLength | hirda->Init.Parity | hirda->Init.Mode);
  
  /*-------------------------- USART CR3 Configuration -----------------------*/
  /* Clear CTSE and RTSE bits */
  CLEAR_BIT(hirda->Instance->CR3, USART_CR3_RTSE | USART_CR3_CTSE);
  
  /*-------------------------- USART BRR Configuration -----------------------*/
#if defined(USART6)  
  if((hirda->Instance == USART1) || (hirda->Instance == USART6))
  {
    SET_BIT(hirda->Instance->BRR, IRDA_BRR(HAL_RCC_GetPCLK2Freq(), hirda->Init.BaudRate));
  }
#else
  if(hirda->Instance == USART1)
  {
    SET_BIT(hirda->Instance->BRR, IRDA_BRR(HAL_RCC_GetPCLK2Freq(), hirda->Init.BaudRate));
  }	
#endif /* USART6 */
  else
  {
    SET_BIT(hirda->Instance->BRR, IRDA_BRR(HAL_RCC_GetPCLK1Freq(), hirda->Init.BaudRate));
  }
}

/**
  * @}
  */

#endif /* HAL_IRDA_MODULE_ENABLED */
/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/