view Small_CPU/Src/i2c.c @ 842:c3dd461ca3f9 Evo_2_23

Migrated Sentinel protocol to new UART structure: The Sentinel protocol had not been migrated to the new UART structure which was introduced with the introduction of the UART MUX. The Sentinel is now supported by autodetection again (development version only)
author Ideenmodellierer
date Mon, 15 Jan 2024 21:44:18 +0100
parents 4fe5400567e7
children
line wrap: on
line source

#include "baseCPU2.h"
#include "i2c.h"
#include "scheduler.h"

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/


//  ===============================================================================
//	I2C addresses - see i2c.h
//  ===============================================================================

I2C_HandleTypeDef I2cHandle;


/*
static void I2C_Error_Handler(void)
{
  while(1)
  {
  }
}
*/

GPIO_PinState HAL_I2C_Read_Data_PIN(void)
{
	return HAL_GPIO_ReadPin(I2Cx_SDA_GPIO_PORT,I2Cx_SDA_PIN);
}

void HAL_I2C_Send_One_CLOCK(void)
{
	HAL_GPIO_WritePin(I2Cx_SCL_GPIO_PORT, I2Cx_SCL_PIN, GPIO_PIN_RESET);
	HAL_Delay(1); 
	HAL_GPIO_WritePin(I2Cx_SCL_GPIO_PORT, I2Cx_SCL_PIN, GPIO_PIN_SET);
	HAL_Delay(1);
}

GPIO_PinState MX_I2C1_TestAndClear(void)
{
	GPIO_PinState retval;
	uint8_t repeatcnt = 3;

	I2C_DeInit();
	HAL_I2C_ManualControl_MspInit();
	
/* The SDA line is expected to be HIGH if no com is pending => send dummy clock signals if that is not the case */
	do
	{
		for(int i=0; i<20;i++)
		{
			if(HAL_I2C_Read_Data_PIN() == GPIO_PIN_RESET)
				HAL_I2C_Send_One_CLOCK();
			else
				break;
		}
		retval = HAL_I2C_Read_Data_PIN();
	}while ((repeatcnt-- > 0) && (retval != GPIO_PIN_SET));

	return retval;
}

HAL_StatusTypeDef MX_I2C1_Init(void)
{
  I2cHandle.Instance             = I2Cx;
  I2cHandle.Init.AddressingMode  = I2C_ADDRESSINGMODE_7BIT;
  I2cHandle.Init.ClockSpeed      = 88000; /* Reduced to avoid behavior described in errata: Mismatch on the “Setup time for a repeated Start condition” */
  I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
  I2cHandle.Init.DutyCycle       = I2C_DUTYCYCLE_2;				/* don't care if not in fast mode */
  I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLED;
  I2cHandle.Init.NoStretchMode   = I2C_NOSTRETCH_DISABLED;
  I2cHandle.Init.OwnAddress1     = 0x01;						/* don't care because of master mode */

/* According to documentation setting filters before I2C initialization is recommended */
	/* HAL_I2CEx_AnalogFilter_Config(&I2cHandle, I2C_ANALOGFILTER_ENABLED); */
	HAL_I2CEx_ConfigDigitalFilter(&I2cHandle,0x0F);

	global.I2C_SystemStatus = HAL_I2C_Init(&I2cHandle);

	if(global.dataSendToSlavePending)
	{
		scheduleSpecial_Evaluate_DataSendToSlave();
	}
	return global.I2C_SystemStatus;
}


void I2C_DeInit(void)
{
	HAL_I2C_DeInit(&I2cHandle);
}

static uint8_t i2c_errors = 0;

void I2C_Error_count(void)
{
	i2c_errors++;
}


HAL_StatusTypeDef I2C_Master_Transmit(  uint16_t DevAddress, uint8_t *pData, uint16_t Size)
{
	if(global.I2C_SystemStatus != HAL_OK)
		return global.I2C_SystemStatus;

	global.I2C_SystemStatus = HAL_I2C_Master_Transmit(&I2cHandle, DevAddress,  pData, Size, 10);
	if(global.I2C_SystemStatus != HAL_OK)
	{
		I2C_Error_count();
	}
	
	return global.I2C_SystemStatus;
}

HAL_StatusTypeDef I2C_Master_Receive(  uint16_t DevAddress, uint8_t *pData, uint16_t Size)
{
	if(global.I2C_SystemStatus != HAL_OK)
		return global.I2C_SystemStatus;

	global.I2C_SystemStatus = HAL_I2C_Master_Receive(&I2cHandle, DevAddress,  pData, Size, 10);
	if(global.I2C_SystemStatus != HAL_OK)
	{
		I2C_Error_count();
	}

	return global.I2C_SystemStatus;
}