Mercurial > public > ostc4
view Common/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc_ex.c @ 842:c3dd461ca3f9 Evo_2_23
Migrated Sentinel protocol to new UART structure:
The Sentinel protocol had not been migrated to the new UART structure which was introduced with the introduction of the UART MUX. The Sentinel is now supported by autodetection again (development version only)
author | Ideenmodellierer |
---|---|
date | Mon, 15 Jan 2024 21:44:18 +0100 |
parents | c78bcbd5deda |
children |
line wrap: on
line source
/** ****************************************************************************** * @file stm32f4xx_hal_rcc_ex.c * @author MCD Application Team * @brief Extension RCC HAL module driver. * This file provides firmware functions to manage the following * functionalities RCC extension peripheral: * + Extended Peripheral Control functions * ****************************************************************************** * @attention * * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2> * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ #include "stm32f4xx_hal.h" /** @addtogroup STM32F4xx_HAL_Driver * @{ */ /** @defgroup RCCEx RCCEx * @brief RCCEx HAL module driver * @{ */ #ifdef HAL_RCC_MODULE_ENABLED /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ /** @addtogroup RCCEx_Private_Constants * @{ */ /** * @} */ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Private function prototypes -----------------------------------------------*/ /* Private functions ---------------------------------------------------------*/ /** @defgroup RCCEx_Exported_Functions RCCEx Exported Functions * @{ */ /** @defgroup RCCEx_Exported_Functions_Group1 Extended Peripheral Control functions * @brief Extended Peripheral Control functions * @verbatim =============================================================================== ##### Extended Peripheral Control functions ##### =============================================================================== [..] This subsection provides a set of functions allowing to control the RCC Clocks frequencies. [..] (@) Important note: Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select the RTC clock source; in this case the Backup domain will be reset in order to modify the RTC Clock source, as consequence RTC registers (including the backup registers) and RCC_BDCR register are set to their reset values. @endverbatim * @{ */ #if defined(STM32F446xx) /** * @brief Initializes the RCC extended peripherals clocks according to the specified * parameters in the RCC_PeriphCLKInitTypeDef. * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that * contains the configuration information for the Extended Peripherals * clocks(I2S, SAI, LTDC RTC and TIM). * * @note Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select * the RTC clock source; in this case the Backup domain will be reset in * order to modify the RTC Clock source, as consequence RTC registers (including * the backup registers) and RCC_BDCR register are set to their reset values. * * @retval HAL status */ HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) { uint32_t tickstart = 0U; uint32_t tmpreg1 = 0U; uint32_t plli2sp = 0U; uint32_t plli2sq = 0U; uint32_t plli2sr = 0U; uint32_t pllsaip = 0U; uint32_t pllsaiq = 0U; uint32_t plli2sused = 0U; uint32_t pllsaiused = 0U; /* Check the peripheral clock selection parameters */ assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); /*------------------------ I2S APB1 configuration --------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB1) == (RCC_PERIPHCLK_I2S_APB1)) { /* Check the parameters */ assert_param(IS_RCC_I2SAPB1CLKSOURCE(PeriphClkInit->I2sApb1ClockSelection)); /* Configure I2S Clock source */ __HAL_RCC_I2S_APB1_CONFIG(PeriphClkInit->I2sApb1ClockSelection); /* Enable the PLLI2S when it's used as clock source for I2S */ if(PeriphClkInit->I2sApb1ClockSelection == RCC_I2SAPB1CLKSOURCE_PLLI2S) { plli2sused = 1U; } } /*--------------------------------------------------------------------------*/ /*---------------------------- I2S APB2 configuration ----------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB2) == (RCC_PERIPHCLK_I2S_APB2)) { /* Check the parameters */ assert_param(IS_RCC_I2SAPB2CLKSOURCE(PeriphClkInit->I2sApb2ClockSelection)); /* Configure I2S Clock source */ __HAL_RCC_I2S_APB2_CONFIG(PeriphClkInit->I2sApb2ClockSelection); /* Enable the PLLI2S when it's used as clock source for I2S */ if(PeriphClkInit->I2sApb2ClockSelection == RCC_I2SAPB2CLKSOURCE_PLLI2S) { plli2sused = 1U; } } /*--------------------------------------------------------------------------*/ /*--------------------------- SAI1 configuration ---------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI1) == (RCC_PERIPHCLK_SAI1)) { /* Check the parameters */ assert_param(IS_RCC_SAI1CLKSOURCE(PeriphClkInit->Sai1ClockSelection)); /* Configure SAI1 Clock source */ __HAL_RCC_SAI1_CONFIG(PeriphClkInit->Sai1ClockSelection); /* Enable the PLLI2S when it's used as clock source for SAI */ if(PeriphClkInit->Sai1ClockSelection == RCC_SAI1CLKSOURCE_PLLI2S) { plli2sused = 1U; } /* Enable the PLLSAI when it's used as clock source for SAI */ if(PeriphClkInit->Sai1ClockSelection == RCC_SAI1CLKSOURCE_PLLSAI) { pllsaiused = 1U; } } /*--------------------------------------------------------------------------*/ /*-------------------------- SAI2 configuration ----------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI2) == (RCC_PERIPHCLK_SAI2)) { /* Check the parameters */ assert_param(IS_RCC_SAI2CLKSOURCE(PeriphClkInit->Sai2ClockSelection)); /* Configure SAI2 Clock source */ __HAL_RCC_SAI2_CONFIG(PeriphClkInit->Sai2ClockSelection); /* Enable the PLLI2S when it's used as clock source for SAI */ if(PeriphClkInit->Sai2ClockSelection == RCC_SAI2CLKSOURCE_PLLI2S) { plli2sused = 1U; } /* Enable the PLLSAI when it's used as clock source for SAI */ if(PeriphClkInit->Sai2ClockSelection == RCC_SAI2CLKSOURCE_PLLSAI) { pllsaiused = 1U; } } /*--------------------------------------------------------------------------*/ /*----------------------------- RTC configuration --------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC)) { /* Check for RTC Parameters used to output RTCCLK */ assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); /* Enable Power Clock*/ __HAL_RCC_PWR_CLK_ENABLE(); /* Enable write access to Backup domain */ PWR->CR |= PWR_CR_DBP; /* Get tick */ tickstart = HAL_GetTick(); while((PWR->CR & PWR_CR_DBP) == RESET) { if((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ tmpreg1 = (RCC->BDCR & RCC_BDCR_RTCSEL); if((tmpreg1 != 0x00000000U) && ((tmpreg1) != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) { /* Store the content of BDCR register before the reset of Backup Domain */ tmpreg1 = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); /* RTC Clock selection can be changed only if the Backup Domain is reset */ __HAL_RCC_BACKUPRESET_FORCE(); __HAL_RCC_BACKUPRESET_RELEASE(); /* Restore the Content of BDCR register */ RCC->BDCR = tmpreg1; /* Wait for LSE reactivation if LSE was enable prior to Backup Domain reset */ if(HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSEON)) { /* Get tick */ tickstart = HAL_GetTick(); /* Wait till LSE is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) { if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } } __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); } /*--------------------------------------------------------------------------*/ /*---------------------------- TIM configuration ---------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_TIM) == (RCC_PERIPHCLK_TIM)) { /* Configure Timer Prescaler */ __HAL_RCC_TIMCLKPRESCALER(PeriphClkInit->TIMPresSelection); } /*--------------------------------------------------------------------------*/ /*---------------------------- FMPI2C1 Configuration -----------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_FMPI2C1) == RCC_PERIPHCLK_FMPI2C1) { /* Check the parameters */ assert_param(IS_RCC_FMPI2C1CLKSOURCE(PeriphClkInit->Fmpi2c1ClockSelection)); /* Configure the FMPI2C1 clock source */ __HAL_RCC_FMPI2C1_CONFIG(PeriphClkInit->Fmpi2c1ClockSelection); } /*--------------------------------------------------------------------------*/ /*------------------------------ CEC Configuration -------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CEC) == RCC_PERIPHCLK_CEC) { /* Check the parameters */ assert_param(IS_RCC_CECCLKSOURCE(PeriphClkInit->CecClockSelection)); /* Configure the CEC clock source */ __HAL_RCC_CEC_CONFIG(PeriphClkInit->CecClockSelection); } /*--------------------------------------------------------------------------*/ /*----------------------------- CLK48 Configuration ------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) { /* Check the parameters */ assert_param(IS_RCC_CLK48CLKSOURCE(PeriphClkInit->Clk48ClockSelection)); /* Configure the CLK48 clock source */ __HAL_RCC_CLK48_CONFIG(PeriphClkInit->Clk48ClockSelection); /* Enable the PLLSAI when it's used as clock source for CLK48 */ if(PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLSAIP) { pllsaiused = 1U; } } /*--------------------------------------------------------------------------*/ /*----------------------------- SDIO Configuration -------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SDIO) == RCC_PERIPHCLK_SDIO) { /* Check the parameters */ assert_param(IS_RCC_SDIOCLKSOURCE(PeriphClkInit->SdioClockSelection)); /* Configure the SDIO clock source */ __HAL_RCC_SDIO_CONFIG(PeriphClkInit->SdioClockSelection); } /*--------------------------------------------------------------------------*/ /*------------------------------ SPDIFRX Configuration ---------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SPDIFRX) == RCC_PERIPHCLK_SPDIFRX) { /* Check the parameters */ assert_param(IS_RCC_SPDIFRXCLKSOURCE(PeriphClkInit->SpdifClockSelection)); /* Configure the SPDIFRX clock source */ __HAL_RCC_SPDIFRX_CONFIG(PeriphClkInit->SpdifClockSelection); /* Enable the PLLI2S when it's used as clock source for SPDIFRX */ if(PeriphClkInit->SpdifClockSelection == RCC_SPDIFRXCLKSOURCE_PLLI2SP) { plli2sused = 1U; } } /*--------------------------------------------------------------------------*/ /*---------------------------- PLLI2S Configuration ------------------------*/ /* PLLI2S is configured when a peripheral will use it as source clock : SAI1, SAI2, I2S on APB1, I2S on APB2 or SPDIFRX */ if((plli2sused == 1U) || (PeriphClkInit->PeriphClockSelection == RCC_PERIPHCLK_PLLI2S)) { /* Disable the PLLI2S */ __HAL_RCC_PLLI2S_DISABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLI2S is disabled */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) { if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } /* check for common PLLI2S Parameters */ assert_param(IS_RCC_PLLI2SM_VALUE(PeriphClkInit->PLLI2S.PLLI2SM)); assert_param(IS_RCC_PLLI2SN_VALUE(PeriphClkInit->PLLI2S.PLLI2SN)); /*------ In Case of PLLI2S is selected as source clock for I2S -----------*/ if(((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB1) == RCC_PERIPHCLK_I2S_APB1) && (PeriphClkInit->I2sApb1ClockSelection == RCC_I2SAPB1CLKSOURCE_PLLI2S)) || ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB2) == RCC_PERIPHCLK_I2S_APB2) && (PeriphClkInit->I2sApb2ClockSelection == RCC_I2SAPB2CLKSOURCE_PLLI2S))) { /* check for Parameters */ assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); /* Read PLLI2SP/PLLI2SQ value from PLLI2SCFGR register (this value is not needed for I2S configuration) */ plli2sp = ((((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SP) >> RCC_PLLI2SCFGR_PLLI2SP_Pos) + 1U) << 1U); plli2sq = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> RCC_PLLI2SCFGR_PLLI2SQ_Pos); /* Configure the PLLI2S division factors */ /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM) */ /* I2SCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SR */ __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN , plli2sp, plli2sq, PeriphClkInit->PLLI2S.PLLI2SR); } /*------- In Case of PLLI2S is selected as source clock for SAI ----------*/ if(((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI1) == RCC_PERIPHCLK_SAI1) && (PeriphClkInit->Sai1ClockSelection == RCC_SAI1CLKSOURCE_PLLI2S)) || ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI2) == RCC_PERIPHCLK_SAI2) && (PeriphClkInit->Sai2ClockSelection == RCC_SAI2CLKSOURCE_PLLI2S))) { /* Check for PLLI2S Parameters */ assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); /* Check for PLLI2S/DIVQ parameters */ assert_param(IS_RCC_PLLI2S_DIVQ_VALUE(PeriphClkInit->PLLI2SDivQ)); /* Read PLLI2SP/PLLI2SR value from PLLI2SCFGR register (this value is not needed for SAI configuration) */ plli2sp = ((((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SP) >> RCC_PLLI2SCFGR_PLLI2SP_Pos) + 1U) << 1U); plli2sr = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> RCC_PLLI2SCFGR_PLLI2SR_Pos); /* Configure the PLLI2S division factors */ /* PLLI2S_VCO Input = PLL_SOURCE/PLLI2SM */ /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ /* SAI_CLK(first level) = PLLI2S_VCO Output/PLLI2SQ */ __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN , plli2sp, PeriphClkInit->PLLI2S.PLLI2SQ, plli2sr); /* SAI_CLK_x = SAI_CLK(first level)/PLLI2SDIVQ */ __HAL_RCC_PLLI2S_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLI2SDivQ); } /*------ In Case of PLLI2S is selected as source clock for SPDIFRX -------*/ if((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SPDIFRX) == RCC_PERIPHCLK_SPDIFRX) && (PeriphClkInit->SpdifClockSelection == RCC_SPDIFRXCLKSOURCE_PLLI2SP)) { /* check for Parameters */ assert_param(IS_RCC_PLLI2SP_VALUE(PeriphClkInit->PLLI2S.PLLI2SP)); /* Read PLLI2SR value from PLLI2SCFGR register (this value is not need for SAI configuration) */ plli2sq = ((((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SP) >> RCC_PLLI2SCFGR_PLLI2SP_Pos) + 1U) << 1U); plli2sr = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> RCC_PLLI2SCFGR_PLLI2SR_Pos); /* Configure the PLLI2S division factors */ /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM) */ /* SPDIFRXCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SP */ __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN , PeriphClkInit->PLLI2S.PLLI2SP, plli2sq, plli2sr); } /*----------------- In Case of PLLI2S is just selected -----------------*/ if((PeriphClkInit->PeriphClockSelection & RCC_PERIPHCLK_PLLI2S) == RCC_PERIPHCLK_PLLI2S) { /* Check for Parameters */ assert_param(IS_RCC_PLLI2SP_VALUE(PeriphClkInit->PLLI2S.PLLI2SP)); assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); /* Configure the PLLI2S division factors */ /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM) */ __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN , PeriphClkInit->PLLI2S.PLLI2SP, PeriphClkInit->PLLI2S.PLLI2SQ, PeriphClkInit->PLLI2S.PLLI2SR); } /* Enable the PLLI2S */ __HAL_RCC_PLLI2S_ENABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLI2S is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) { if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } } /*--------------------------------------------------------------------------*/ /*----------------------------- PLLSAI Configuration -----------------------*/ /* PLLSAI is configured when a peripheral will use it as source clock : SAI1, SAI2, CLK48 or SDIO */ if(pllsaiused == 1U) { /* Disable PLLSAI Clock */ __HAL_RCC_PLLSAI_DISABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLSAI is disabled */ while(__HAL_RCC_PLLSAI_GET_FLAG() != RESET) { if((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } /* Check the PLLSAI division factors */ assert_param(IS_RCC_PLLSAIM_VALUE(PeriphClkInit->PLLSAI.PLLSAIM)); assert_param(IS_RCC_PLLSAIN_VALUE(PeriphClkInit->PLLSAI.PLLSAIN)); /*------ In Case of PLLSAI is selected as source clock for SAI -----------*/ if(((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI1) == RCC_PERIPHCLK_SAI1) && (PeriphClkInit->Sai1ClockSelection == RCC_SAI1CLKSOURCE_PLLSAI)) || ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI2) == RCC_PERIPHCLK_SAI2) && (PeriphClkInit->Sai2ClockSelection == RCC_SAI2CLKSOURCE_PLLSAI))) { /* check for PLLSAIQ Parameter */ assert_param(IS_RCC_PLLSAIQ_VALUE(PeriphClkInit->PLLSAI.PLLSAIQ)); /* check for PLLSAI/DIVQ Parameter */ assert_param(IS_RCC_PLLSAI_DIVQ_VALUE(PeriphClkInit->PLLSAIDivQ)); /* Read PLLSAIP value from PLLSAICFGR register (this value is not needed for SAI configuration) */ pllsaip = ((((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIP) >> RCC_PLLSAICFGR_PLLSAIP_Pos) + 1U) << 1U); /* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ /* SAI_CLK(first level) = PLLSAI_VCO Output/PLLSAIQ */ __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIM, PeriphClkInit->PLLSAI.PLLSAIN , pllsaip, PeriphClkInit->PLLSAI.PLLSAIQ, 0U); /* SAI_CLK_x = SAI_CLK(first level)/PLLSAIDIVQ */ __HAL_RCC_PLLSAI_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLSAIDivQ); } /*------ In Case of PLLSAI is selected as source clock for CLK48 ---------*/ /* In Case of PLLI2S is selected as source clock for CLK48 */ if((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) && (PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLSAIP)) { /* check for Parameters */ assert_param(IS_RCC_PLLSAIP_VALUE(PeriphClkInit->PLLSAI.PLLSAIP)); /* Read PLLSAIQ value from PLLI2SCFGR register (this value is not need for SAI configuration) */ pllsaiq = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> RCC_PLLSAICFGR_PLLSAIQ_Pos); /* Configure the PLLSAI division factors */ /* PLLSAI_VCO = f(VCO clock) = f(PLLSAI clock input) * (PLLI2SN/PLLSAIM) */ /* 48CLK = f(PLLSAI clock output) = f(VCO clock) / PLLSAIP */ __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIM, PeriphClkInit->PLLSAI.PLLSAIN , PeriphClkInit->PLLSAI.PLLSAIP, pllsaiq, 0U); } /* Enable PLLSAI Clock */ __HAL_RCC_PLLSAI_ENABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLSAI is ready */ while(__HAL_RCC_PLLSAI_GET_FLAG() == RESET) { if((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } } return HAL_OK; } /** * @brief Get the RCC_PeriphCLKInitTypeDef according to the internal * RCC configuration registers. * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that * will be configured. * @retval None */ void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) { uint32_t tempreg; /* Set all possible values for the extended clock type parameter------------*/ PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_I2S_APB1 | RCC_PERIPHCLK_I2S_APB2 |\ RCC_PERIPHCLK_SAI1 | RCC_PERIPHCLK_SAI2 |\ RCC_PERIPHCLK_TIM | RCC_PERIPHCLK_RTC |\ RCC_PERIPHCLK_CEC | RCC_PERIPHCLK_FMPI2C1 |\ RCC_PERIPHCLK_CLK48 | RCC_PERIPHCLK_SDIO |\ RCC_PERIPHCLK_SPDIFRX; /* Get the PLLI2S Clock configuration --------------------------------------*/ PeriphClkInit->PLLI2S.PLLI2SM = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM) >> RCC_PLLI2SCFGR_PLLI2SM_Pos); PeriphClkInit->PLLI2S.PLLI2SN = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> RCC_PLLI2SCFGR_PLLI2SN_Pos); PeriphClkInit->PLLI2S.PLLI2SP = (uint32_t)((((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SP) >> RCC_PLLI2SCFGR_PLLI2SP_Pos) + 1U) << 1U); PeriphClkInit->PLLI2S.PLLI2SQ = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> RCC_PLLI2SCFGR_PLLI2SQ_Pos); PeriphClkInit->PLLI2S.PLLI2SR = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> RCC_PLLI2SCFGR_PLLI2SR_Pos); /* Get the PLLSAI Clock configuration --------------------------------------*/ PeriphClkInit->PLLSAI.PLLSAIM = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIM) >> RCC_PLLSAICFGR_PLLSAIM_Pos); PeriphClkInit->PLLSAI.PLLSAIN = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIN) >> RCC_PLLSAICFGR_PLLSAIN_Pos); PeriphClkInit->PLLSAI.PLLSAIP = (uint32_t)((((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIP) >> RCC_PLLSAICFGR_PLLSAIP_Pos) + 1U) << 1U); PeriphClkInit->PLLSAI.PLLSAIQ = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> RCC_PLLSAICFGR_PLLSAIQ_Pos); /* Get the PLLSAI/PLLI2S division factors ----------------------------------*/ PeriphClkInit->PLLI2SDivQ = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLI2SDIVQ) >> RCC_DCKCFGR_PLLI2SDIVQ_Pos); PeriphClkInit->PLLSAIDivQ = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLSAIDIVQ) >> RCC_DCKCFGR_PLLSAIDIVQ_Pos); /* Get the SAI1 clock configuration ----------------------------------------*/ PeriphClkInit->Sai1ClockSelection = __HAL_RCC_GET_SAI1_SOURCE(); /* Get the SAI2 clock configuration ----------------------------------------*/ PeriphClkInit->Sai2ClockSelection = __HAL_RCC_GET_SAI2_SOURCE(); /* Get the I2S APB1 clock configuration ------------------------------------*/ PeriphClkInit->I2sApb1ClockSelection = __HAL_RCC_GET_I2S_APB1_SOURCE(); /* Get the I2S APB2 clock configuration ------------------------------------*/ PeriphClkInit->I2sApb2ClockSelection = __HAL_RCC_GET_I2S_APB2_SOURCE(); /* Get the RTC Clock configuration -----------------------------------------*/ tempreg = (RCC->CFGR & RCC_CFGR_RTCPRE); PeriphClkInit->RTCClockSelection = (uint32_t)((tempreg) | (RCC->BDCR & RCC_BDCR_RTCSEL)); /* Get the CEC clock configuration -----------------------------------------*/ PeriphClkInit->CecClockSelection = __HAL_RCC_GET_CEC_SOURCE(); /* Get the FMPI2C1 clock configuration -------------------------------------*/ PeriphClkInit->Fmpi2c1ClockSelection = __HAL_RCC_GET_FMPI2C1_SOURCE(); /* Get the CLK48 clock configuration ----------------------------------------*/ PeriphClkInit->Clk48ClockSelection = __HAL_RCC_GET_CLK48_SOURCE(); /* Get the SDIO clock configuration ----------------------------------------*/ PeriphClkInit->SdioClockSelection = __HAL_RCC_GET_SDIO_SOURCE(); /* Get the SPDIFRX clock configuration -------------------------------------*/ PeriphClkInit->SpdifClockSelection = __HAL_RCC_GET_SPDIFRX_SOURCE(); /* Get the TIM Prescaler configuration -------------------------------------*/ if ((RCC->DCKCFGR & RCC_DCKCFGR_TIMPRE) == RESET) { PeriphClkInit->TIMPresSelection = RCC_TIMPRES_DESACTIVATED; } else { PeriphClkInit->TIMPresSelection = RCC_TIMPRES_ACTIVATED; } } /** * @brief Return the peripheral clock frequency for a given peripheral(SAI..) * @note Return 0 if peripheral clock identifier not managed by this API * @param PeriphClk Peripheral clock identifier * This parameter can be one of the following values: * @arg RCC_PERIPHCLK_SAI1: SAI1 peripheral clock * @arg RCC_PERIPHCLK_SAI2: SAI2 peripheral clock * @arg RCC_PERIPHCLK_I2S_APB1: I2S APB1 peripheral clock * @arg RCC_PERIPHCLK_I2S_APB2: I2S APB2 peripheral clock * @retval Frequency in KHz */ uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk) { uint32_t tmpreg1 = 0U; /* This variable used to store the SAI clock frequency (value in Hz) */ uint32_t frequency = 0U; /* This variable used to store the VCO Input (value in Hz) */ uint32_t vcoinput = 0U; /* This variable used to store the SAI clock source */ uint32_t saiclocksource = 0U; uint32_t srcclk = 0U; /* This variable used to store the VCO Output (value in Hz) */ uint32_t vcooutput = 0U; switch (PeriphClk) { case RCC_PERIPHCLK_SAI1: case RCC_PERIPHCLK_SAI2: { saiclocksource = RCC->DCKCFGR; saiclocksource &= (RCC_DCKCFGR_SAI1SRC | RCC_DCKCFGR_SAI2SRC); switch (saiclocksource) { case 0U: /* PLLSAI is the clock source for SAI*/ { /* Configure the PLLSAI division factor */ /* PLLSAI_VCO Input = PLL_SOURCE/PLLSAIM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) { /* In Case the PLL Source is HSI (Internal Clock) */ vcoinput = (HSI_VALUE / (uint32_t)(RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIM)); } else { /* In Case the PLL Source is HSE (External Clock) */ vcoinput = ((HSE_VALUE / (uint32_t)(RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIM))); } /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ /* SAI_CLK(first level) = PLLSAI_VCO Output/PLLSAIQ */ tmpreg1 = (RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> 24U; frequency = (vcoinput * ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIN) >> 6U))/(tmpreg1); /* SAI_CLK_x = SAI_CLK(first level)/PLLSAIDIVQ */ tmpreg1 = (((RCC->DCKCFGR & RCC_DCKCFGR_PLLSAIDIVQ) >> 8U) + 1U); frequency = frequency/(tmpreg1); break; } case RCC_DCKCFGR_SAI1SRC_0: /* PLLI2S is the clock source for SAI*/ case RCC_DCKCFGR_SAI2SRC_0: /* PLLI2S is the clock source for SAI*/ { /* Configure the PLLI2S division factor */ /* PLLI2S_VCO Input = PLL_SOURCE/PLLI2SM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) { /* In Case the PLL Source is HSI (Internal Clock) */ vcoinput = (HSI_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); } else { /* In Case the PLL Source is HSE (External Clock) */ vcoinput = ((HSE_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM))); } /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ /* SAI_CLK(first level) = PLLI2S_VCO Output/PLLI2SQ */ tmpreg1 = (RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> 24U; frequency = (vcoinput * ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> 6U))/(tmpreg1); /* SAI_CLK_x = SAI_CLK(first level)/PLLI2SDIVQ */ tmpreg1 = ((RCC->DCKCFGR & RCC_DCKCFGR_PLLI2SDIVQ) + 1U); frequency = frequency/(tmpreg1); break; } case RCC_DCKCFGR_SAI1SRC_1: /* PLLR is the clock source for SAI*/ case RCC_DCKCFGR_SAI2SRC_1: /* PLLR is the clock source for SAI*/ { /* Configure the PLLI2S division factor */ /* PLL_VCO Input = PLL_SOURCE/PLLM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) { /* In Case the PLL Source is HSI (Internal Clock) */ vcoinput = (HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } else { /* In Case the PLL Source is HSE (External Clock) */ vcoinput = ((HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM))); } /* PLL_VCO Output = PLL_VCO Input * PLLN */ /* SAI_CLK_x = PLL_VCO Output/PLLR */ tmpreg1 = (RCC->PLLCFGR & RCC_PLLCFGR_PLLR) >> 28U; frequency = (vcoinput * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6U))/(tmpreg1); break; } case RCC_DCKCFGR_SAI1SRC: /* External clock is the clock source for SAI*/ { frequency = EXTERNAL_CLOCK_VALUE; break; } case RCC_DCKCFGR_SAI2SRC: /* PLLSRC(HSE or HSI) is the clock source for SAI*/ { if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSI) { /* In Case the PLL Source is HSI (Internal Clock) */ frequency = (uint32_t)(HSI_VALUE); } else { /* In Case the PLL Source is HSE (External Clock) */ frequency = (uint32_t)(HSE_VALUE); } break; } default : { break; } } break; } case RCC_PERIPHCLK_I2S_APB1: { /* Get the current I2S source */ srcclk = __HAL_RCC_GET_I2S_APB1_SOURCE(); switch (srcclk) { /* Check if I2S clock selection is External clock mapped on the I2S_CKIN pin used as I2S clock */ case RCC_I2SAPB1CLKSOURCE_EXT: { /* Set the I2S clock to the external clock value */ frequency = EXTERNAL_CLOCK_VALUE; break; } /* Check if I2S clock selection is PLLI2S VCO output clock divided by PLLI2SR used as I2S clock */ case RCC_I2SAPB1CLKSOURCE_PLLI2S: { /* Configure the PLLI2S division factor */ /* PLLI2S_VCO Input = PLL_SOURCE/PLLI2SM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSE_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); } else { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSI_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); } /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ vcooutput = (uint32_t)(vcoinput * (((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> 6U) & (RCC_PLLI2SCFGR_PLLI2SN >> 6U))); /* I2S_CLK = PLLI2S_VCO Output/PLLI2SR */ frequency = (uint32_t)(vcooutput /(((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> 28U) & (RCC_PLLI2SCFGR_PLLI2SR >> 28U))); break; } /* Check if I2S clock selection is PLL VCO Output divided by PLLR used as I2S clock */ case RCC_I2SAPB1CLKSOURCE_PLLR: { /* Configure the PLL division factor R */ /* PLL_VCO Input = PLL_SOURCE/PLLM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } else { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } /* PLL_VCO Output = PLL_VCO Input * PLLN */ vcooutput = (uint32_t)(vcoinput * (((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6U) & (RCC_PLLCFGR_PLLN >> 6U))); /* I2S_CLK = PLL_VCO Output/PLLR */ frequency = (uint32_t)(vcooutput /(((RCC->PLLCFGR & RCC_PLLCFGR_PLLR) >> 28U) & (RCC_PLLCFGR_PLLR >> 28U))); break; } /* Check if I2S clock selection is HSI or HSE depending from PLL source Clock */ case RCC_I2SAPB1CLKSOURCE_PLLSRC: { if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { frequency = HSE_VALUE; } else { frequency = HSI_VALUE; } break; } /* Clock not enabled for I2S*/ default: { frequency = 0U; break; } } break; } case RCC_PERIPHCLK_I2S_APB2: { /* Get the current I2S source */ srcclk = __HAL_RCC_GET_I2S_APB2_SOURCE(); switch (srcclk) { /* Check if I2S clock selection is External clock mapped on the I2S_CKIN pin used as I2S clock */ case RCC_I2SAPB2CLKSOURCE_EXT: { /* Set the I2S clock to the external clock value */ frequency = EXTERNAL_CLOCK_VALUE; break; } /* Check if I2S clock selection is PLLI2S VCO output clock divided by PLLI2SR used as I2S clock */ case RCC_I2SAPB2CLKSOURCE_PLLI2S: { /* Configure the PLLI2S division factor */ /* PLLI2S_VCO Input = PLL_SOURCE/PLLI2SM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSE_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); } else { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSI_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); } /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ vcooutput = (uint32_t)(vcoinput * (((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> 6U) & (RCC_PLLI2SCFGR_PLLI2SN >> 6U))); /* I2S_CLK = PLLI2S_VCO Output/PLLI2SR */ frequency = (uint32_t)(vcooutput /(((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> 28U) & (RCC_PLLI2SCFGR_PLLI2SR >> 28U))); break; } /* Check if I2S clock selection is PLL VCO Output divided by PLLR used as I2S clock */ case RCC_I2SAPB2CLKSOURCE_PLLR: { /* Configure the PLL division factor R */ /* PLL_VCO Input = PLL_SOURCE/PLLM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } else { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } /* PLL_VCO Output = PLL_VCO Input * PLLN */ vcooutput = (uint32_t)(vcoinput * (((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6U) & (RCC_PLLCFGR_PLLN >> 6U))); /* I2S_CLK = PLL_VCO Output/PLLR */ frequency = (uint32_t)(vcooutput /(((RCC->PLLCFGR & RCC_PLLCFGR_PLLR) >> 28U) & (RCC_PLLCFGR_PLLR >> 28U))); break; } /* Check if I2S clock selection is HSI or HSE depending from PLL source Clock */ case RCC_I2SAPB2CLKSOURCE_PLLSRC: { if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { frequency = HSE_VALUE; } else { frequency = HSI_VALUE; } break; } /* Clock not enabled for I2S*/ default: { frequency = 0U; break; } } break; } } return frequency; } #endif /* STM32F446xx */ #if defined(STM32F469xx) || defined(STM32F479xx) /** * @brief Initializes the RCC extended peripherals clocks according to the specified * parameters in the RCC_PeriphCLKInitTypeDef. * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that * contains the configuration information for the Extended Peripherals * clocks(I2S, SAI, LTDC, RTC and TIM). * * @note Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select * the RTC clock source; in this case the Backup domain will be reset in * order to modify the RTC Clock source, as consequence RTC registers (including * the backup registers) and RCC_BDCR register are set to their reset values. * * @retval HAL status */ HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) { uint32_t tickstart = 0U; uint32_t tmpreg1 = 0U; uint32_t pllsaip = 0U; uint32_t pllsaiq = 0U; uint32_t pllsair = 0U; /* Check the parameters */ assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); /*--------------------------- CLK48 Configuration --------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) { /* Check the parameters */ assert_param(IS_RCC_CLK48CLKSOURCE(PeriphClkInit->Clk48ClockSelection)); /* Configure the CLK48 clock source */ __HAL_RCC_CLK48_CONFIG(PeriphClkInit->Clk48ClockSelection); } /*--------------------------------------------------------------------------*/ /*------------------------------ SDIO Configuration ------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SDIO) == RCC_PERIPHCLK_SDIO) { /* Check the parameters */ assert_param(IS_RCC_SDIOCLKSOURCE(PeriphClkInit->SdioClockSelection)); /* Configure the SDIO clock source */ __HAL_RCC_SDIO_CONFIG(PeriphClkInit->SdioClockSelection); } /*--------------------------------------------------------------------------*/ /*----------------------- SAI/I2S Configuration (PLLI2S) -------------------*/ /*------------------- Common configuration SAI/I2S -------------------------*/ /* In Case of SAI or I2S Clock Configuration through PLLI2S, PLLI2SN division factor is common parameters for both peripherals */ if((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == RCC_PERIPHCLK_I2S) || (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLI2S) == RCC_PERIPHCLK_SAI_PLLI2S) || (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_PLLI2S) == RCC_PERIPHCLK_PLLI2S)) { /* check for Parameters */ assert_param(IS_RCC_PLLI2SN_VALUE(PeriphClkInit->PLLI2S.PLLI2SN)); /* Disable the PLLI2S */ __HAL_RCC_PLLI2S_DISABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLI2S is disabled */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) { if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } /*---------------------- I2S configuration -------------------------------*/ /* In Case of I2S Clock Configuration through PLLI2S, PLLI2SR must be added only for I2S configuration */ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == (RCC_PERIPHCLK_I2S)) { /* check for Parameters */ assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); /* Configure the PLLI2S division factors */ /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) x (PLLI2SN/PLLM) */ /* I2SCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SR */ __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN , PeriphClkInit->PLLI2S.PLLI2SR); } /*---------------------------- SAI configuration -------------------------*/ /* In Case of SAI Clock Configuration through PLLI2S, PLLI2SQ and PLLI2S_DIVQ must be added only for SAI configuration */ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLI2S) == (RCC_PERIPHCLK_SAI_PLLI2S)) { /* Check the PLLI2S division factors */ assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); assert_param(IS_RCC_PLLI2S_DIVQ_VALUE(PeriphClkInit->PLLI2SDivQ)); /* Read PLLI2SR value from PLLI2SCFGR register (this value is not need for SAI configuration) */ tmpreg1 = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> RCC_PLLI2SCFGR_PLLI2SR_Pos); /* Configure the PLLI2S division factors */ /* PLLI2S_VCO Input = PLL_SOURCE/PLLM */ /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ /* SAI_CLK(first level) = PLLI2S_VCO Output/PLLI2SQ */ __HAL_RCC_PLLI2S_SAICLK_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN , PeriphClkInit->PLLI2S.PLLI2SQ , tmpreg1); /* SAI_CLK_x = SAI_CLK(first level)/PLLI2SDIVQ */ __HAL_RCC_PLLI2S_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLI2SDivQ); } /*----------------- In Case of PLLI2S is just selected -----------------*/ if((PeriphClkInit->PeriphClockSelection & RCC_PERIPHCLK_PLLI2S) == RCC_PERIPHCLK_PLLI2S) { /* Check for Parameters */ assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); /* Configure the PLLI2S multiplication and division factors */ __HAL_RCC_PLLI2S_SAICLK_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN, PeriphClkInit->PLLI2S.PLLI2SQ, PeriphClkInit->PLLI2S.PLLI2SR); } /* Enable the PLLI2S */ __HAL_RCC_PLLI2S_ENABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLI2S is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) { if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } } /*--------------------------------------------------------------------------*/ /*----------------------- SAI/LTDC Configuration (PLLSAI) ------------------*/ /*----------------------- Common configuration SAI/LTDC --------------------*/ /* In Case of SAI, LTDC or CLK48 Clock Configuration through PLLSAI, PLLSAIN division factor is common parameters for these peripherals */ if((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLSAI) == RCC_PERIPHCLK_SAI_PLLSAI) || (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LTDC) == RCC_PERIPHCLK_LTDC) || ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) && (PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLSAIP))) { /* Check the PLLSAI division factors */ assert_param(IS_RCC_PLLSAIN_VALUE(PeriphClkInit->PLLSAI.PLLSAIN)); /* Disable PLLSAI Clock */ __HAL_RCC_PLLSAI_DISABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLSAI is disabled */ while(__HAL_RCC_PLLSAI_GET_FLAG() != RESET) { if((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } /*---------------------------- SAI configuration -------------------------*/ /* In Case of SAI Clock Configuration through PLLSAI, PLLSAIQ and PLLSAI_DIVQ must be added only for SAI configuration */ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLSAI) == (RCC_PERIPHCLK_SAI_PLLSAI)) { assert_param(IS_RCC_PLLSAIQ_VALUE(PeriphClkInit->PLLSAI.PLLSAIQ)); assert_param(IS_RCC_PLLSAI_DIVQ_VALUE(PeriphClkInit->PLLSAIDivQ)); /* Read PLLSAIP value from PLLSAICFGR register (this value is not needed for SAI configuration) */ pllsaip = ((((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIP) >> RCC_PLLSAICFGR_PLLSAIP_Pos) + 1U) << 1U); /* Read PLLSAIR value from PLLSAICFGR register (this value is not need for SAI configuration) */ pllsair = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIR) >> RCC_PLLSAICFGR_PLLSAIR_Pos); /* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ /* SAI_CLK(first level) = PLLSAI_VCO Output/PLLSAIQ */ __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIN, pllsaip, PeriphClkInit->PLLSAI.PLLSAIQ, pllsair); /* SAI_CLK_x = SAI_CLK(first level)/PLLSAIDIVQ */ __HAL_RCC_PLLSAI_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLSAIDivQ); } /*---------------------------- LTDC configuration ------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LTDC) == (RCC_PERIPHCLK_LTDC)) { assert_param(IS_RCC_PLLSAIR_VALUE(PeriphClkInit->PLLSAI.PLLSAIR)); assert_param(IS_RCC_PLLSAI_DIVR_VALUE(PeriphClkInit->PLLSAIDivR)); /* Read PLLSAIP value from PLLSAICFGR register (this value is not needed for SAI configuration) */ pllsaip = ((((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIP) >> RCC_PLLSAICFGR_PLLSAIP_Pos) + 1U) << 1U); /* Read PLLSAIQ value from PLLSAICFGR register (this value is not need for SAI configuration) */ pllsaiq = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> RCC_PLLSAICFGR_PLLSAIQ_Pos); /* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ /* LTDC_CLK(first level) = PLLSAI_VCO Output/PLLSAIR */ __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIN, pllsaip, pllsaiq, PeriphClkInit->PLLSAI.PLLSAIR); /* LTDC_CLK = LTDC_CLK(first level)/PLLSAIDIVR */ __HAL_RCC_PLLSAI_PLLSAICLKDIVR_CONFIG(PeriphClkInit->PLLSAIDivR); } /*---------------------------- CLK48 configuration ------------------------*/ /* Configure the PLLSAI when it is used as clock source for CLK48 */ if((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == (RCC_PERIPHCLK_CLK48)) && (PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLSAIP)) { assert_param(IS_RCC_PLLSAIP_VALUE(PeriphClkInit->PLLSAI.PLLSAIP)); /* Read PLLSAIQ value from PLLSAICFGR register (this value is not need for SAI configuration) */ pllsaiq = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> RCC_PLLSAICFGR_PLLSAIQ_Pos); /* Read PLLSAIR value from PLLSAICFGR register (this value is not need for SAI configuration) */ pllsair = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIR) >> RCC_PLLSAICFGR_PLLSAIR_Pos); /* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ /* CLK48_CLK(first level) = PLLSAI_VCO Output/PLLSAIP */ __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIN, PeriphClkInit->PLLSAI.PLLSAIP, pllsaiq, pllsair); } /* Enable PLLSAI Clock */ __HAL_RCC_PLLSAI_ENABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLSAI is ready */ while(__HAL_RCC_PLLSAI_GET_FLAG() == RESET) { if((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } } /*--------------------------------------------------------------------------*/ /*---------------------------- RTC configuration ---------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC)) { /* Check for RTC Parameters used to output RTCCLK */ assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); /* Enable Power Clock*/ __HAL_RCC_PWR_CLK_ENABLE(); /* Enable write access to Backup domain */ PWR->CR |= PWR_CR_DBP; /* Get tick */ tickstart = HAL_GetTick(); while((PWR->CR & PWR_CR_DBP) == RESET) { if((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ tmpreg1 = (RCC->BDCR & RCC_BDCR_RTCSEL); if((tmpreg1 != 0x00000000U) && ((tmpreg1) != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) { /* Store the content of BDCR register before the reset of Backup Domain */ tmpreg1 = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); /* RTC Clock selection can be changed only if the Backup Domain is reset */ __HAL_RCC_BACKUPRESET_FORCE(); __HAL_RCC_BACKUPRESET_RELEASE(); /* Restore the Content of BDCR register */ RCC->BDCR = tmpreg1; /* Wait for LSE reactivation if LSE was enable prior to Backup Domain reset */ if(HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSEON)) { /* Get tick */ tickstart = HAL_GetTick(); /* Wait till LSE is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) { if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } } __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); } /*--------------------------------------------------------------------------*/ /*---------------------------- TIM configuration ---------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_TIM) == (RCC_PERIPHCLK_TIM)) { __HAL_RCC_TIMCLKPRESCALER(PeriphClkInit->TIMPresSelection); } return HAL_OK; } /** * @brief Configures the RCC_PeriphCLKInitTypeDef according to the internal * RCC configuration registers. * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that * will be configured. * @retval None */ void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) { uint32_t tempreg; /* Set all possible values for the extended clock type parameter------------*/ PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_I2S | RCC_PERIPHCLK_SAI_PLLSAI |\ RCC_PERIPHCLK_SAI_PLLI2S | RCC_PERIPHCLK_LTDC |\ RCC_PERIPHCLK_TIM | RCC_PERIPHCLK_RTC |\ RCC_PERIPHCLK_CLK48 | RCC_PERIPHCLK_SDIO; /* Get the PLLI2S Clock configuration --------------------------------------*/ PeriphClkInit->PLLI2S.PLLI2SN = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> RCC_PLLI2SCFGR_PLLI2SN_Pos); PeriphClkInit->PLLI2S.PLLI2SR = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> RCC_PLLI2SCFGR_PLLI2SR_Pos); PeriphClkInit->PLLI2S.PLLI2SQ = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> RCC_PLLI2SCFGR_PLLI2SQ_Pos); /* Get the PLLSAI Clock configuration --------------------------------------*/ PeriphClkInit->PLLSAI.PLLSAIN = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIN) >> RCC_PLLSAICFGR_PLLSAIN_Pos); PeriphClkInit->PLLSAI.PLLSAIR = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIR) >> RCC_PLLSAICFGR_PLLSAIR_Pos); PeriphClkInit->PLLSAI.PLLSAIQ = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> RCC_PLLSAICFGR_PLLSAIQ_Pos); /* Get the PLLSAI/PLLI2S division factors ----------------------------------*/ PeriphClkInit->PLLI2SDivQ = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLI2SDIVQ) >> RCC_DCKCFGR_PLLI2SDIVQ_Pos); PeriphClkInit->PLLSAIDivQ = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLSAIDIVQ) >> RCC_DCKCFGR_PLLSAIDIVQ_Pos); PeriphClkInit->PLLSAIDivR = (uint32_t)(RCC->DCKCFGR & RCC_DCKCFGR_PLLSAIDIVR); /* Get the RTC Clock configuration -----------------------------------------*/ tempreg = (RCC->CFGR & RCC_CFGR_RTCPRE); PeriphClkInit->RTCClockSelection = (uint32_t)((tempreg) | (RCC->BDCR & RCC_BDCR_RTCSEL)); /* Get the CLK48 clock configuration -------------------------------------*/ PeriphClkInit->Clk48ClockSelection = __HAL_RCC_GET_CLK48_SOURCE(); /* Get the SDIO clock configuration ----------------------------------------*/ PeriphClkInit->SdioClockSelection = __HAL_RCC_GET_SDIO_SOURCE(); if ((RCC->DCKCFGR & RCC_DCKCFGR_TIMPRE) == RESET) { PeriphClkInit->TIMPresSelection = RCC_TIMPRES_DESACTIVATED; } else { PeriphClkInit->TIMPresSelection = RCC_TIMPRES_ACTIVATED; } } /** * @brief Return the peripheral clock frequency for a given peripheral(SAI..) * @note Return 0 if peripheral clock identifier not managed by this API * @param PeriphClk Peripheral clock identifier * This parameter can be one of the following values: * @arg RCC_PERIPHCLK_I2S: I2S peripheral clock * @retval Frequency in KHz */ uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk) { /* This variable used to store the I2S clock frequency (value in Hz) */ uint32_t frequency = 0U; /* This variable used to store the VCO Input (value in Hz) */ uint32_t vcoinput = 0U; uint32_t srcclk = 0U; /* This variable used to store the VCO Output (value in Hz) */ uint32_t vcooutput = 0U; switch (PeriphClk) { case RCC_PERIPHCLK_I2S: { /* Get the current I2S source */ srcclk = __HAL_RCC_GET_I2S_SOURCE(); switch (srcclk) { /* Check if I2S clock selection is External clock mapped on the I2S_CKIN pin used as I2S clock */ case RCC_I2SCLKSOURCE_EXT: { /* Set the I2S clock to the external clock value */ frequency = EXTERNAL_CLOCK_VALUE; break; } /* Check if I2S clock selection is PLLI2S VCO output clock divided by PLLI2SR used as I2S clock */ case RCC_I2SCLKSOURCE_PLLI2S: { /* Configure the PLLI2S division factor */ /* PLLI2S_VCO Input = PLL_SOURCE/PLLI2SM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } else { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ vcooutput = (uint32_t)(vcoinput * (((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> 6U) & (RCC_PLLI2SCFGR_PLLI2SN >> 6U))); /* I2S_CLK = PLLI2S_VCO Output/PLLI2SR */ frequency = (uint32_t)(vcooutput /(((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> 28U) & (RCC_PLLI2SCFGR_PLLI2SR >> 28U))); break; } /* Clock not enabled for I2S*/ default: { frequency = 0U; break; } } break; } } return frequency; } #endif /* STM32F469xx || STM32F479xx */ #if defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) || defined(STM32F413xx) || defined(STM32F423xx) /** * @brief Initializes the RCC extended peripherals clocks according to the specified * parameters in the RCC_PeriphCLKInitTypeDef. * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that * contains the configuration information for the Extended Peripherals * clocks(I2S, LTDC RTC and TIM). * * @note Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select * the RTC clock source; in this case the Backup domain will be reset in * order to modify the RTC Clock source, as consequence RTC registers (including * the backup registers) and RCC_BDCR register are set to their reset values. * * @retval HAL status */ HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) { uint32_t tickstart = 0U; uint32_t tmpreg1 = 0U; #if defined(STM32F413xx) || defined(STM32F423xx) uint32_t plli2sq = 0U; #endif /* STM32F413xx || STM32F423xx */ uint32_t plli2sused = 0U; /* Check the peripheral clock selection parameters */ assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); /*----------------------------------- I2S APB1 configuration ---------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB1) == (RCC_PERIPHCLK_I2S_APB1)) { /* Check the parameters */ assert_param(IS_RCC_I2SAPB1CLKSOURCE(PeriphClkInit->I2sApb1ClockSelection)); /* Configure I2S Clock source */ __HAL_RCC_I2S_APB1_CONFIG(PeriphClkInit->I2sApb1ClockSelection); /* Enable the PLLI2S when it's used as clock source for I2S */ if(PeriphClkInit->I2sApb1ClockSelection == RCC_I2SAPB1CLKSOURCE_PLLI2S) { plli2sused = 1U; } } /*--------------------------------------------------------------------------*/ /*----------------------------------- I2S APB2 configuration ---------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB2) == (RCC_PERIPHCLK_I2S_APB2)) { /* Check the parameters */ assert_param(IS_RCC_I2SAPB2CLKSOURCE(PeriphClkInit->I2sApb2ClockSelection)); /* Configure I2S Clock source */ __HAL_RCC_I2S_APB2_CONFIG(PeriphClkInit->I2sApb2ClockSelection); /* Enable the PLLI2S when it's used as clock source for I2S */ if(PeriphClkInit->I2sApb2ClockSelection == RCC_I2SAPB2CLKSOURCE_PLLI2S) { plli2sused = 1U; } } /*--------------------------------------------------------------------------*/ #if defined(STM32F413xx) || defined(STM32F423xx) /*----------------------- SAI1 Block A configuration -----------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAIA) == (RCC_PERIPHCLK_SAIA)) { /* Check the parameters */ assert_param(IS_RCC_SAIACLKSOURCE(PeriphClkInit->SaiAClockSelection)); /* Configure SAI1 Clock source */ __HAL_RCC_SAI_BLOCKACLKSOURCE_CONFIG(PeriphClkInit->SaiAClockSelection); /* Enable the PLLI2S when it's used as clock source for SAI */ if(PeriphClkInit->SaiAClockSelection == RCC_SAIACLKSOURCE_PLLI2SR) { plli2sused = 1U; } /* Enable the PLLSAI when it's used as clock source for SAI */ if(PeriphClkInit->SaiAClockSelection == RCC_SAIACLKSOURCE_PLLR) { /* Check for PLL/DIVR parameters */ assert_param(IS_RCC_PLL_DIVR_VALUE(PeriphClkInit->PLLDivR)); /* SAI_CLK_x = SAI_CLK(first level)/PLLDIVR */ __HAL_RCC_PLL_PLLSAICLKDIVR_CONFIG(PeriphClkInit->PLLDivR); } } /*--------------------------------------------------------------------------*/ /*---------------------- SAI1 Block B configuration ------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAIB) == (RCC_PERIPHCLK_SAIB)) { /* Check the parameters */ assert_param(IS_RCC_SAIBCLKSOURCE(PeriphClkInit->SaiBClockSelection)); /* Configure SAI1 Clock source */ __HAL_RCC_SAI_BLOCKBCLKSOURCE_CONFIG(PeriphClkInit->SaiBClockSelection); /* Enable the PLLI2S when it's used as clock source for SAI */ if(PeriphClkInit->SaiBClockSelection == RCC_SAIBCLKSOURCE_PLLI2SR) { plli2sused = 1U; } /* Enable the PLLSAI when it's used as clock source for SAI */ if(PeriphClkInit->SaiBClockSelection == RCC_SAIBCLKSOURCE_PLLR) { /* Check for PLL/DIVR parameters */ assert_param(IS_RCC_PLL_DIVR_VALUE(PeriphClkInit->PLLDivR)); /* SAI_CLK_x = SAI_CLK(first level)/PLLDIVR */ __HAL_RCC_PLL_PLLSAICLKDIVR_CONFIG(PeriphClkInit->PLLDivR); } } /*--------------------------------------------------------------------------*/ #endif /* STM32F413xx || STM32F423xx */ /*------------------------------------ RTC configuration -------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC)) { /* Check for RTC Parameters used to output RTCCLK */ assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); /* Enable Power Clock*/ __HAL_RCC_PWR_CLK_ENABLE(); /* Enable write access to Backup domain */ PWR->CR |= PWR_CR_DBP; /* Get tick */ tickstart = HAL_GetTick(); while((PWR->CR & PWR_CR_DBP) == RESET) { if((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ tmpreg1 = (RCC->BDCR & RCC_BDCR_RTCSEL); if((tmpreg1 != 0x00000000U) && ((tmpreg1) != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) { /* Store the content of BDCR register before the reset of Backup Domain */ tmpreg1 = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); /* RTC Clock selection can be changed only if the Backup Domain is reset */ __HAL_RCC_BACKUPRESET_FORCE(); __HAL_RCC_BACKUPRESET_RELEASE(); /* Restore the Content of BDCR register */ RCC->BDCR = tmpreg1; /* Wait for LSE reactivation if LSE was enable prior to Backup Domain reset */ if(HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSEON)) { /* Get tick */ tickstart = HAL_GetTick(); /* Wait till LSE is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) { if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } } __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); } /*--------------------------------------------------------------------------*/ /*------------------------------------ TIM configuration -------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_TIM) == (RCC_PERIPHCLK_TIM)) { /* Configure Timer Prescaler */ __HAL_RCC_TIMCLKPRESCALER(PeriphClkInit->TIMPresSelection); } /*--------------------------------------------------------------------------*/ /*------------------------------------- FMPI2C1 Configuration --------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_FMPI2C1) == RCC_PERIPHCLK_FMPI2C1) { /* Check the parameters */ assert_param(IS_RCC_FMPI2C1CLKSOURCE(PeriphClkInit->Fmpi2c1ClockSelection)); /* Configure the FMPI2C1 clock source */ __HAL_RCC_FMPI2C1_CONFIG(PeriphClkInit->Fmpi2c1ClockSelection); } /*--------------------------------------------------------------------------*/ /*------------------------------------- CLK48 Configuration ----------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) { /* Check the parameters */ assert_param(IS_RCC_CLK48CLKSOURCE(PeriphClkInit->Clk48ClockSelection)); /* Configure the SDIO clock source */ __HAL_RCC_CLK48_CONFIG(PeriphClkInit->Clk48ClockSelection); /* Enable the PLLI2S when it's used as clock source for CLK48 */ if(PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLI2SQ) { plli2sused = 1U; } } /*--------------------------------------------------------------------------*/ /*------------------------------------- SDIO Configuration -----------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SDIO) == RCC_PERIPHCLK_SDIO) { /* Check the parameters */ assert_param(IS_RCC_SDIOCLKSOURCE(PeriphClkInit->SdioClockSelection)); /* Configure the SDIO clock source */ __HAL_RCC_SDIO_CONFIG(PeriphClkInit->SdioClockSelection); } /*--------------------------------------------------------------------------*/ /*-------------------------------------- PLLI2S Configuration --------------*/ /* PLLI2S is configured when a peripheral will use it as source clock : I2S on APB1 or I2S on APB2*/ if((plli2sused == 1U) || (PeriphClkInit->PeriphClockSelection == RCC_PERIPHCLK_PLLI2S)) { /* Disable the PLLI2S */ __HAL_RCC_PLLI2S_DISABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLI2S is disabled */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) { if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } /* check for common PLLI2S Parameters */ assert_param(IS_RCC_PLLI2SCLKSOURCE(PeriphClkInit->PLLI2SSelection)); assert_param(IS_RCC_PLLI2SM_VALUE(PeriphClkInit->PLLI2S.PLLI2SM)); assert_param(IS_RCC_PLLI2SN_VALUE(PeriphClkInit->PLLI2S.PLLI2SN)); /*-------------------- Set the PLL I2S clock -----------------------------*/ __HAL_RCC_PLL_I2S_CONFIG(PeriphClkInit->PLLI2SSelection); /*------- In Case of PLLI2S is selected as source clock for I2S ----------*/ if(((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB1) == RCC_PERIPHCLK_I2S_APB1) && (PeriphClkInit->I2sApb1ClockSelection == RCC_I2SAPB1CLKSOURCE_PLLI2S)) || ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S_APB2) == RCC_PERIPHCLK_I2S_APB2) && (PeriphClkInit->I2sApb2ClockSelection == RCC_I2SAPB2CLKSOURCE_PLLI2S)) || ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_CLK48) == RCC_PERIPHCLK_CLK48) && (PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLI2SQ)) || ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SDIO) == RCC_PERIPHCLK_SDIO) && (PeriphClkInit->SdioClockSelection == RCC_SDIOCLKSOURCE_CLK48) && (PeriphClkInit->Clk48ClockSelection == RCC_CLK48CLKSOURCE_PLLI2SQ))) { /* check for Parameters */ assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); /* Configure the PLLI2S division factors */ /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM)*/ /* I2SCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SR */ __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN , PeriphClkInit->PLLI2S.PLLI2SQ, PeriphClkInit->PLLI2S.PLLI2SR); } #if defined(STM32F413xx) || defined(STM32F423xx) /*------- In Case of PLLI2S is selected as source clock for SAI ----------*/ if(((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAIA) == RCC_PERIPHCLK_SAIA) && (PeriphClkInit->SaiAClockSelection == RCC_SAIACLKSOURCE_PLLI2SR)) || ((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAIB) == RCC_PERIPHCLK_SAIB) && (PeriphClkInit->SaiBClockSelection == RCC_SAIBCLKSOURCE_PLLI2SR))) { /* Check for PLLI2S Parameters */ assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); /* Check for PLLI2S/DIVR parameters */ assert_param(IS_RCC_PLLI2S_DIVR_VALUE(PeriphClkInit->PLLI2SDivR)); /* Read PLLI2SQ value from PLLI2SCFGR register (this value is not needed for SAI configuration) */ plli2sq = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> RCC_PLLI2SCFGR_PLLI2SQ_Pos); /* Configure the PLLI2S division factors */ /* PLLI2S_VCO Input = PLL_SOURCE/PLLI2SM */ /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ /* SAI_CLK(first level) = PLLI2S_VCO Output/PLLI2SQ */ __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN, plli2sq, PeriphClkInit->PLLI2S.PLLI2SR); /* SAI_CLK_x = SAI_CLK(first level)/PLLI2SDIVR */ __HAL_RCC_PLLI2S_PLLSAICLKDIVR_CONFIG(PeriphClkInit->PLLI2SDivR); } #endif /* STM32F413xx || STM32F423xx */ /*----------------- In Case of PLLI2S is just selected ------------------*/ if((PeriphClkInit->PeriphClockSelection & RCC_PERIPHCLK_PLLI2S) == RCC_PERIPHCLK_PLLI2S) { /* Check for Parameters */ assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); /* Configure the PLLI2S division factors */ /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM)*/ /* SPDIFRXCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SP */ __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN , PeriphClkInit->PLLI2S.PLLI2SQ, PeriphClkInit->PLLI2S.PLLI2SR); } /* Enable the PLLI2S */ __HAL_RCC_PLLI2S_ENABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLI2S is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) { if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } } /*--------------------------------------------------------------------------*/ /*-------------------- DFSDM1 clock source configuration -------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_DFSDM1) == RCC_PERIPHCLK_DFSDM1) { /* Check the parameters */ assert_param(IS_RCC_DFSDM1CLKSOURCE(PeriphClkInit->Dfsdm1ClockSelection)); /* Configure the DFSDM1 interface clock source */ __HAL_RCC_DFSDM1_CONFIG(PeriphClkInit->Dfsdm1ClockSelection); } /*--------------------------------------------------------------------------*/ /*-------------------- DFSDM1 Audio clock source configuration -------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_DFSDM1_AUDIO) == RCC_PERIPHCLK_DFSDM1_AUDIO) { /* Check the parameters */ assert_param(IS_RCC_DFSDM1AUDIOCLKSOURCE(PeriphClkInit->Dfsdm1AudioClockSelection)); /* Configure the DFSDM1 Audio interface clock source */ __HAL_RCC_DFSDM1AUDIO_CONFIG(PeriphClkInit->Dfsdm1AudioClockSelection); } /*--------------------------------------------------------------------------*/ #if defined(STM32F413xx) || defined(STM32F423xx) /*-------------------- DFSDM2 clock source configuration -------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_DFSDM2) == RCC_PERIPHCLK_DFSDM2) { /* Check the parameters */ assert_param(IS_RCC_DFSDM2CLKSOURCE(PeriphClkInit->Dfsdm2ClockSelection)); /* Configure the DFSDM1 interface clock source */ __HAL_RCC_DFSDM2_CONFIG(PeriphClkInit->Dfsdm2ClockSelection); } /*--------------------------------------------------------------------------*/ /*-------------------- DFSDM2 Audio clock source configuration -------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_DFSDM2_AUDIO) == RCC_PERIPHCLK_DFSDM2_AUDIO) { /* Check the parameters */ assert_param(IS_RCC_DFSDM2AUDIOCLKSOURCE(PeriphClkInit->Dfsdm2AudioClockSelection)); /* Configure the DFSDM1 Audio interface clock source */ __HAL_RCC_DFSDM2AUDIO_CONFIG(PeriphClkInit->Dfsdm2AudioClockSelection); } /*--------------------------------------------------------------------------*/ /*---------------------------- LPTIM1 Configuration ------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LPTIM1) == RCC_PERIPHCLK_LPTIM1) { /* Check the parameters */ assert_param(IS_RCC_LPTIM1CLKSOURCE(PeriphClkInit->Lptim1ClockSelection)); /* Configure the LPTIM1 clock source */ __HAL_RCC_LPTIM1_CONFIG(PeriphClkInit->Lptim1ClockSelection); } /*--------------------------------------------------------------------------*/ #endif /* STM32F413xx || STM32F423xx */ return HAL_OK; } /** * @brief Get the RCC_PeriphCLKInitTypeDef according to the internal * RCC configuration registers. * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that * will be configured. * @retval None */ void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) { uint32_t tempreg; /* Set all possible values for the extended clock type parameter------------*/ #if defined(STM32F413xx) || defined(STM32F423xx) PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_I2S_APB1 | RCC_PERIPHCLK_I2S_APB2 |\ RCC_PERIPHCLK_TIM | RCC_PERIPHCLK_RTC |\ RCC_PERIPHCLK_FMPI2C1 | RCC_PERIPHCLK_CLK48 |\ RCC_PERIPHCLK_SDIO | RCC_PERIPHCLK_DFSDM1 |\ RCC_PERIPHCLK_DFSDM1_AUDIO | RCC_PERIPHCLK_DFSDM2 |\ RCC_PERIPHCLK_DFSDM2_AUDIO | RCC_PERIPHCLK_LPTIM1 |\ RCC_PERIPHCLK_SAIA | RCC_PERIPHCLK_SAIB; #else /* STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx */ PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_I2S_APB1 | RCC_PERIPHCLK_I2S_APB2 |\ RCC_PERIPHCLK_TIM | RCC_PERIPHCLK_RTC |\ RCC_PERIPHCLK_FMPI2C1 | RCC_PERIPHCLK_CLK48 |\ RCC_PERIPHCLK_SDIO | RCC_PERIPHCLK_DFSDM1 |\ RCC_PERIPHCLK_DFSDM1_AUDIO; #endif /* STM32F413xx || STM32F423xx */ /* Get the PLLI2S Clock configuration --------------------------------------*/ PeriphClkInit->PLLI2S.PLLI2SM = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM) >> RCC_PLLI2SCFGR_PLLI2SM_Pos); PeriphClkInit->PLLI2S.PLLI2SN = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> RCC_PLLI2SCFGR_PLLI2SN_Pos); PeriphClkInit->PLLI2S.PLLI2SQ = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> RCC_PLLI2SCFGR_PLLI2SQ_Pos); PeriphClkInit->PLLI2S.PLLI2SR = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> RCC_PLLI2SCFGR_PLLI2SR_Pos); #if defined(STM32F413xx) || defined(STM32F423xx) /* Get the PLL/PLLI2S division factors -------------------------------------*/ PeriphClkInit->PLLI2SDivR = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLI2SDIVR) >> RCC_DCKCFGR_PLLI2SDIVR_Pos); PeriphClkInit->PLLDivR = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLDIVR) >> RCC_DCKCFGR_PLLDIVR_Pos); #endif /* STM32F413xx || STM32F423xx */ /* Get the I2S APB1 clock configuration ------------------------------------*/ PeriphClkInit->I2sApb1ClockSelection = __HAL_RCC_GET_I2S_APB1_SOURCE(); /* Get the I2S APB2 clock configuration ------------------------------------*/ PeriphClkInit->I2sApb2ClockSelection = __HAL_RCC_GET_I2S_APB2_SOURCE(); /* Get the RTC Clock configuration -----------------------------------------*/ tempreg = (RCC->CFGR & RCC_CFGR_RTCPRE); PeriphClkInit->RTCClockSelection = (uint32_t)((tempreg) | (RCC->BDCR & RCC_BDCR_RTCSEL)); /* Get the FMPI2C1 clock configuration -------------------------------------*/ PeriphClkInit->Fmpi2c1ClockSelection = __HAL_RCC_GET_FMPI2C1_SOURCE(); /* Get the CLK48 clock configuration ---------------------------------------*/ PeriphClkInit->Clk48ClockSelection = __HAL_RCC_GET_CLK48_SOURCE(); /* Get the SDIO clock configuration ----------------------------------------*/ PeriphClkInit->SdioClockSelection = __HAL_RCC_GET_SDIO_SOURCE(); /* Get the DFSDM1 clock configuration --------------------------------------*/ PeriphClkInit->Dfsdm1ClockSelection = __HAL_RCC_GET_DFSDM1_SOURCE(); /* Get the DFSDM1 Audio clock configuration --------------------------------*/ PeriphClkInit->Dfsdm1AudioClockSelection = __HAL_RCC_GET_DFSDM1AUDIO_SOURCE(); #if defined(STM32F413xx) || defined(STM32F423xx) /* Get the DFSDM2 clock configuration --------------------------------------*/ PeriphClkInit->Dfsdm2ClockSelection = __HAL_RCC_GET_DFSDM2_SOURCE(); /* Get the DFSDM2 Audio clock configuration --------------------------------*/ PeriphClkInit->Dfsdm2AudioClockSelection = __HAL_RCC_GET_DFSDM2AUDIO_SOURCE(); /* Get the LPTIM1 clock configuration --------------------------------------*/ PeriphClkInit->Lptim1ClockSelection = __HAL_RCC_GET_LPTIM1_SOURCE(); /* Get the SAI1 Block Aclock configuration ---------------------------------*/ PeriphClkInit->SaiAClockSelection = __HAL_RCC_GET_SAI_BLOCKA_SOURCE(); /* Get the SAI1 Block B clock configuration --------------------------------*/ PeriphClkInit->SaiBClockSelection = __HAL_RCC_GET_SAI_BLOCKB_SOURCE(); #endif /* STM32F413xx || STM32F423xx */ /* Get the TIM Prescaler configuration -------------------------------------*/ if ((RCC->DCKCFGR & RCC_DCKCFGR_TIMPRE) == RESET) { PeriphClkInit->TIMPresSelection = RCC_TIMPRES_DESACTIVATED; } else { PeriphClkInit->TIMPresSelection = RCC_TIMPRES_ACTIVATED; } } /** * @brief Return the peripheral clock frequency for a given peripheral(I2S..) * @note Return 0 if peripheral clock identifier not managed by this API * @param PeriphClk Peripheral clock identifier * This parameter can be one of the following values: * @arg RCC_PERIPHCLK_I2S_APB1: I2S APB1 peripheral clock * @arg RCC_PERIPHCLK_I2S_APB2: I2S APB2 peripheral clock * @retval Frequency in KHz */ uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk) { /* This variable used to store the I2S clock frequency (value in Hz) */ uint32_t frequency = 0U; /* This variable used to store the VCO Input (value in Hz) */ uint32_t vcoinput = 0U; uint32_t srcclk = 0U; /* This variable used to store the VCO Output (value in Hz) */ uint32_t vcooutput = 0U; switch (PeriphClk) { case RCC_PERIPHCLK_I2S_APB1: { /* Get the current I2S source */ srcclk = __HAL_RCC_GET_I2S_APB1_SOURCE(); switch (srcclk) { /* Check if I2S clock selection is External clock mapped on the I2S_CKIN pin used as I2S clock */ case RCC_I2SAPB1CLKSOURCE_EXT: { /* Set the I2S clock to the external clock value */ frequency = EXTERNAL_CLOCK_VALUE; break; } /* Check if I2S clock selection is PLLI2S VCO output clock divided by PLLI2SR used as I2S clock */ case RCC_I2SAPB1CLKSOURCE_PLLI2S: { if((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SSRC) == RCC_PLLI2SCFGR_PLLI2SSRC) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(EXTERNAL_CLOCK_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); } else { /* Configure the PLLI2S division factor */ /* PLLI2S_VCO Input = PLL_SOURCE/PLLI2SM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSE_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); } else { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSI_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); } } /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ vcooutput = (uint32_t)(vcoinput * (((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> 6U) & (RCC_PLLI2SCFGR_PLLI2SN >> 6U))); /* I2S_CLK = PLLI2S_VCO Output/PLLI2SR */ frequency = (uint32_t)(vcooutput /(((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> 28U) & (RCC_PLLI2SCFGR_PLLI2SR >> 28U))); break; } /* Check if I2S clock selection is PLL VCO Output divided by PLLR used as I2S clock */ case RCC_I2SAPB1CLKSOURCE_PLLR: { /* Configure the PLL division factor R */ /* PLL_VCO Input = PLL_SOURCE/PLLM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } else { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } /* PLL_VCO Output = PLL_VCO Input * PLLN */ vcooutput = (uint32_t)(vcoinput * (((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6U) & (RCC_PLLCFGR_PLLN >> 6U))); /* I2S_CLK = PLL_VCO Output/PLLR */ frequency = (uint32_t)(vcooutput /(((RCC->PLLCFGR & RCC_PLLCFGR_PLLR) >> 28U) & (RCC_PLLCFGR_PLLR >> 28U))); break; } /* Check if I2S clock selection is HSI or HSE depending from PLL source Clock */ case RCC_I2SAPB1CLKSOURCE_PLLSRC: { if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { frequency = HSE_VALUE; } else { frequency = HSI_VALUE; } break; } /* Clock not enabled for I2S*/ default: { frequency = 0U; break; } } break; } case RCC_PERIPHCLK_I2S_APB2: { /* Get the current I2S source */ srcclk = __HAL_RCC_GET_I2S_APB2_SOURCE(); switch (srcclk) { /* Check if I2S clock selection is External clock mapped on the I2S_CKIN pin used as I2S clock */ case RCC_I2SAPB2CLKSOURCE_EXT: { /* Set the I2S clock to the external clock value */ frequency = EXTERNAL_CLOCK_VALUE; break; } /* Check if I2S clock selection is PLLI2S VCO output clock divided by PLLI2SR used as I2S clock */ case RCC_I2SAPB2CLKSOURCE_PLLI2S: { if((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SSRC) == RCC_PLLI2SCFGR_PLLI2SSRC) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(EXTERNAL_CLOCK_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); } else { /* Configure the PLLI2S division factor */ /* PLLI2S_VCO Input = PLL_SOURCE/PLLI2SM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSE_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); } else { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSI_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); } } /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ vcooutput = (uint32_t)(vcoinput * (((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> 6U) & (RCC_PLLI2SCFGR_PLLI2SN >> 6U))); /* I2S_CLK = PLLI2S_VCO Output/PLLI2SR */ frequency = (uint32_t)(vcooutput /(((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> 28U) & (RCC_PLLI2SCFGR_PLLI2SR >> 28U))); break; } /* Check if I2S clock selection is PLL VCO Output divided by PLLR used as I2S clock */ case RCC_I2SAPB2CLKSOURCE_PLLR: { /* Configure the PLL division factor R */ /* PLL_VCO Input = PLL_SOURCE/PLLM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } else { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } /* PLL_VCO Output = PLL_VCO Input * PLLN */ vcooutput = (uint32_t)(vcoinput * (((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6U) & (RCC_PLLCFGR_PLLN >> 6U))); /* I2S_CLK = PLL_VCO Output/PLLR */ frequency = (uint32_t)(vcooutput /(((RCC->PLLCFGR & RCC_PLLCFGR_PLLR) >> 28U) & (RCC_PLLCFGR_PLLR >> 28U))); break; } /* Check if I2S clock selection is HSI or HSE depending from PLL source Clock */ case RCC_I2SAPB2CLKSOURCE_PLLSRC: { if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { frequency = HSE_VALUE; } else { frequency = HSI_VALUE; } break; } /* Clock not enabled for I2S*/ default: { frequency = 0U; break; } } break; } } return frequency; } #endif /* STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx || STM32F413xx || STM32F423xx */ #if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) /** * @brief Initializes the RCC extended peripherals clocks according to the specified parameters in the * RCC_PeriphCLKInitTypeDef. * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that * contains the configuration information for the Extended Peripherals clocks(I2S and RTC clocks). * * @note A caution to be taken when HAL_RCCEx_PeriphCLKConfig() is used to select RTC clock selection, in this case * the Reset of Backup domain will be applied in order to modify the RTC Clock source as consequence all backup * domain (RTC and RCC_BDCR register expect BKPSRAM) will be reset * * @retval HAL status */ HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) { uint32_t tickstart = 0U; uint32_t tmpreg1 = 0U; /* Check the parameters */ assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); /*---------------------------- RTC configuration ---------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC)) { /* Check for RTC Parameters used to output RTCCLK */ assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); /* Enable Power Clock*/ __HAL_RCC_PWR_CLK_ENABLE(); /* Enable write access to Backup domain */ PWR->CR |= PWR_CR_DBP; /* Get tick */ tickstart = HAL_GetTick(); while((PWR->CR & PWR_CR_DBP) == RESET) { if((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ tmpreg1 = (RCC->BDCR & RCC_BDCR_RTCSEL); if((tmpreg1 != 0x00000000U) && ((tmpreg1) != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) { /* Store the content of BDCR register before the reset of Backup Domain */ tmpreg1 = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); /* RTC Clock selection can be changed only if the Backup Domain is reset */ __HAL_RCC_BACKUPRESET_FORCE(); __HAL_RCC_BACKUPRESET_RELEASE(); /* Restore the Content of BDCR register */ RCC->BDCR = tmpreg1; /* Wait for LSE reactivation if LSE was enable prior to Backup Domain reset */ if(HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSEON)) { /* Get tick */ tickstart = HAL_GetTick(); /* Wait till LSE is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) { if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } } __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); } /*--------------------------------------------------------------------------*/ /*---------------------------- TIM configuration ---------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_TIM) == (RCC_PERIPHCLK_TIM)) { __HAL_RCC_TIMCLKPRESCALER(PeriphClkInit->TIMPresSelection); } /*--------------------------------------------------------------------------*/ /*---------------------------- FMPI2C1 Configuration -----------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_FMPI2C1) == RCC_PERIPHCLK_FMPI2C1) { /* Check the parameters */ assert_param(IS_RCC_FMPI2C1CLKSOURCE(PeriphClkInit->Fmpi2c1ClockSelection)); /* Configure the FMPI2C1 clock source */ __HAL_RCC_FMPI2C1_CONFIG(PeriphClkInit->Fmpi2c1ClockSelection); } /*--------------------------------------------------------------------------*/ /*---------------------------- LPTIM1 Configuration ------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LPTIM1) == RCC_PERIPHCLK_LPTIM1) { /* Check the parameters */ assert_param(IS_RCC_LPTIM1CLKSOURCE(PeriphClkInit->Lptim1ClockSelection)); /* Configure the LPTIM1 clock source */ __HAL_RCC_LPTIM1_CONFIG(PeriphClkInit->Lptim1ClockSelection); } /*---------------------------- I2S Configuration ---------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == RCC_PERIPHCLK_I2S) { /* Check the parameters */ assert_param(IS_RCC_I2SAPBCLKSOURCE(PeriphClkInit->I2SClockSelection)); /* Configure the I2S clock source */ __HAL_RCC_I2S_CONFIG(PeriphClkInit->I2SClockSelection); } return HAL_OK; } /** * @brief Configures the RCC_OscInitStruct according to the internal * RCC configuration registers. * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that * will be configured. * @retval None */ void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) { uint32_t tempreg; /* Set all possible values for the extended clock type parameter------------*/ PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_FMPI2C1 | RCC_PERIPHCLK_LPTIM1 | RCC_PERIPHCLK_TIM | RCC_PERIPHCLK_RTC; tempreg = (RCC->CFGR & RCC_CFGR_RTCPRE); PeriphClkInit->RTCClockSelection = (uint32_t)((tempreg) | (RCC->BDCR & RCC_BDCR_RTCSEL)); if ((RCC->DCKCFGR & RCC_DCKCFGR_TIMPRE) == RESET) { PeriphClkInit->TIMPresSelection = RCC_TIMPRES_DESACTIVATED; } else { PeriphClkInit->TIMPresSelection = RCC_TIMPRES_ACTIVATED; } /* Get the FMPI2C1 clock configuration -------------------------------------*/ PeriphClkInit->Fmpi2c1ClockSelection = __HAL_RCC_GET_FMPI2C1_SOURCE(); /* Get the I2S clock configuration -----------------------------------------*/ PeriphClkInit->I2SClockSelection = __HAL_RCC_GET_I2S_SOURCE(); } /** * @brief Return the peripheral clock frequency for a given peripheral(SAI..) * @note Return 0 if peripheral clock identifier not managed by this API * @param PeriphClk Peripheral clock identifier * This parameter can be one of the following values: * @arg RCC_PERIPHCLK_I2S: I2S peripheral clock * @retval Frequency in KHz */ uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk) { /* This variable used to store the I2S clock frequency (value in Hz) */ uint32_t frequency = 0U; /* This variable used to store the VCO Input (value in Hz) */ uint32_t vcoinput = 0U; uint32_t srcclk = 0U; /* This variable used to store the VCO Output (value in Hz) */ uint32_t vcooutput = 0U; switch (PeriphClk) { case RCC_PERIPHCLK_I2S: { /* Get the current I2S source */ srcclk = __HAL_RCC_GET_I2S_SOURCE(); switch (srcclk) { /* Check if I2S clock selection is External clock mapped on the I2S_CKIN pin used as I2S clock */ case RCC_I2SAPBCLKSOURCE_EXT: { /* Set the I2S clock to the external clock value */ frequency = EXTERNAL_CLOCK_VALUE; break; } /* Check if I2S clock selection is PLL VCO Output divided by PLLR used as I2S clock */ case RCC_I2SAPBCLKSOURCE_PLLR: { /* Configure the PLL division factor R */ /* PLL_VCO Input = PLL_SOURCE/PLLM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } else { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } /* PLL_VCO Output = PLL_VCO Input * PLLN */ vcooutput = (uint32_t)(vcoinput * (((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6U) & (RCC_PLLCFGR_PLLN >> 6U))); /* I2S_CLK = PLL_VCO Output/PLLR */ frequency = (uint32_t)(vcooutput /(((RCC->PLLCFGR & RCC_PLLCFGR_PLLR) >> 28U) & (RCC_PLLCFGR_PLLR >> 28U))); break; } /* Check if I2S clock selection is HSI or HSE depending from PLL source Clock */ case RCC_I2SAPBCLKSOURCE_PLLSRC: { if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { frequency = HSE_VALUE; } else { frequency = HSI_VALUE; } break; } /* Clock not enabled for I2S*/ default: { frequency = 0U; break; } } break; } } return frequency; } #endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */ #if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) /** * @brief Initializes the RCC extended peripherals clocks according to the specified * parameters in the RCC_PeriphCLKInitTypeDef. * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that * contains the configuration information for the Extended Peripherals * clocks(I2S, SAI, LTDC RTC and TIM). * * @note Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select * the RTC clock source; in this case the Backup domain will be reset in * order to modify the RTC Clock source, as consequence RTC registers (including * the backup registers) and RCC_BDCR register are set to their reset values. * * @retval HAL status */ HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) { uint32_t tickstart = 0U; uint32_t tmpreg1 = 0U; /* Check the parameters */ assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); /*----------------------- SAI/I2S Configuration (PLLI2S) -------------------*/ /*----------------------- Common configuration SAI/I2S ---------------------*/ /* In Case of SAI or I2S Clock Configuration through PLLI2S, PLLI2SN division factor is common parameters for both peripherals */ if((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == RCC_PERIPHCLK_I2S) || (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLI2S) == RCC_PERIPHCLK_SAI_PLLI2S)) { /* check for Parameters */ assert_param(IS_RCC_PLLI2SN_VALUE(PeriphClkInit->PLLI2S.PLLI2SN)); /* Disable the PLLI2S */ __HAL_RCC_PLLI2S_DISABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLI2S is disabled */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) { if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } /*---------------------------- I2S configuration -------------------------*/ /* In Case of I2S Clock Configuration through PLLI2S, PLLI2SR must be added only for I2S configuration */ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == (RCC_PERIPHCLK_I2S)) { /* check for Parameters */ assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); /* Configure the PLLI2S division factors */ /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLM) */ /* I2SCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SR */ __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN , PeriphClkInit->PLLI2S.PLLI2SR); } /*---------------------------- SAI configuration -------------------------*/ /* In Case of SAI Clock Configuration through PLLI2S, PLLI2SQ and PLLI2S_DIVQ must be added only for SAI configuration */ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLI2S) == (RCC_PERIPHCLK_SAI_PLLI2S)) { /* Check the PLLI2S division factors */ assert_param(IS_RCC_PLLI2SQ_VALUE(PeriphClkInit->PLLI2S.PLLI2SQ)); assert_param(IS_RCC_PLLI2S_DIVQ_VALUE(PeriphClkInit->PLLI2SDivQ)); /* Read PLLI2SR value from PLLI2SCFGR register (this value is not need for SAI configuration) */ tmpreg1 = ((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> RCC_PLLI2SCFGR_PLLI2SR_Pos); /* Configure the PLLI2S division factors */ /* PLLI2S_VCO Input = PLL_SOURCE/PLLM */ /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ /* SAI_CLK(first level) = PLLI2S_VCO Output/PLLI2SQ */ __HAL_RCC_PLLI2S_SAICLK_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN , PeriphClkInit->PLLI2S.PLLI2SQ , tmpreg1); /* SAI_CLK_x = SAI_CLK(first level)/PLLI2SDIVQ */ __HAL_RCC_PLLI2S_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLI2SDivQ); } /* Enable the PLLI2S */ __HAL_RCC_PLLI2S_ENABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLI2S is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) { if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } } /*--------------------------------------------------------------------------*/ /*----------------------- SAI/LTDC Configuration (PLLSAI) ------------------*/ /*----------------------- Common configuration SAI/LTDC --------------------*/ /* In Case of SAI or LTDC Clock Configuration through PLLSAI, PLLSAIN division factor is common parameters for both peripherals */ if((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLSAI) == RCC_PERIPHCLK_SAI_PLLSAI) || (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LTDC) == RCC_PERIPHCLK_LTDC)) { /* Check the PLLSAI division factors */ assert_param(IS_RCC_PLLSAIN_VALUE(PeriphClkInit->PLLSAI.PLLSAIN)); /* Disable PLLSAI Clock */ __HAL_RCC_PLLSAI_DISABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLSAI is disabled */ while(__HAL_RCC_PLLSAI_GET_FLAG() != RESET) { if((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } /*---------------------------- SAI configuration -------------------------*/ /* In Case of SAI Clock Configuration through PLLSAI, PLLSAIQ and PLLSAI_DIVQ must be added only for SAI configuration */ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_SAI_PLLSAI) == (RCC_PERIPHCLK_SAI_PLLSAI)) { assert_param(IS_RCC_PLLSAIQ_VALUE(PeriphClkInit->PLLSAI.PLLSAIQ)); assert_param(IS_RCC_PLLSAI_DIVQ_VALUE(PeriphClkInit->PLLSAIDivQ)); /* Read PLLSAIR value from PLLSAICFGR register (this value is not need for SAI configuration) */ tmpreg1 = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIR) >> RCC_PLLSAICFGR_PLLSAIR_Pos); /* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ /* SAI_CLK(first level) = PLLSAI_VCO Output/PLLSAIQ */ __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIN , PeriphClkInit->PLLSAI.PLLSAIQ, tmpreg1); /* SAI_CLK_x = SAI_CLK(first level)/PLLSAIDIVQ */ __HAL_RCC_PLLSAI_PLLSAICLKDIVQ_CONFIG(PeriphClkInit->PLLSAIDivQ); } /*---------------------------- LTDC configuration ------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_LTDC) == (RCC_PERIPHCLK_LTDC)) { assert_param(IS_RCC_PLLSAIR_VALUE(PeriphClkInit->PLLSAI.PLLSAIR)); assert_param(IS_RCC_PLLSAI_DIVR_VALUE(PeriphClkInit->PLLSAIDivR)); /* Read PLLSAIR value from PLLSAICFGR register (this value is not need for SAI configuration) */ tmpreg1 = ((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> RCC_PLLSAICFGR_PLLSAIQ_Pos); /* PLLSAI_VCO Input = PLL_SOURCE/PLLM */ /* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAIN */ /* LTDC_CLK(first level) = PLLSAI_VCO Output/PLLSAIR */ __HAL_RCC_PLLSAI_CONFIG(PeriphClkInit->PLLSAI.PLLSAIN , tmpreg1, PeriphClkInit->PLLSAI.PLLSAIR); /* LTDC_CLK = LTDC_CLK(first level)/PLLSAIDIVR */ __HAL_RCC_PLLSAI_PLLSAICLKDIVR_CONFIG(PeriphClkInit->PLLSAIDivR); } /* Enable PLLSAI Clock */ __HAL_RCC_PLLSAI_ENABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLSAI is ready */ while(__HAL_RCC_PLLSAI_GET_FLAG() == RESET) { if((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } } /*--------------------------------------------------------------------------*/ /*---------------------------- RTC configuration ---------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC)) { /* Check for RTC Parameters used to output RTCCLK */ assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); /* Enable Power Clock*/ __HAL_RCC_PWR_CLK_ENABLE(); /* Enable write access to Backup domain */ PWR->CR |= PWR_CR_DBP; /* Get tick */ tickstart = HAL_GetTick(); while((PWR->CR & PWR_CR_DBP) == RESET) { if((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ tmpreg1 = (RCC->BDCR & RCC_BDCR_RTCSEL); if((tmpreg1 != 0x00000000U) && ((tmpreg1) != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) { /* Store the content of BDCR register before the reset of Backup Domain */ tmpreg1 = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); /* RTC Clock selection can be changed only if the Backup Domain is reset */ __HAL_RCC_BACKUPRESET_FORCE(); __HAL_RCC_BACKUPRESET_RELEASE(); /* Restore the Content of BDCR register */ RCC->BDCR = tmpreg1; /* Wait for LSE reactivation if LSE was enable prior to Backup Domain reset */ if(HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSEON)) { /* Get tick */ tickstart = HAL_GetTick(); /* Wait till LSE is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) { if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } } __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); } /*--------------------------------------------------------------------------*/ /*---------------------------- TIM configuration ---------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_TIM) == (RCC_PERIPHCLK_TIM)) { __HAL_RCC_TIMCLKPRESCALER(PeriphClkInit->TIMPresSelection); } return HAL_OK; } /** * @brief Configures the PeriphClkInit according to the internal * RCC configuration registers. * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that * will be configured. * @retval None */ void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) { uint32_t tempreg; /* Set all possible values for the extended clock type parameter------------*/ PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_I2S | RCC_PERIPHCLK_SAI_PLLSAI | RCC_PERIPHCLK_SAI_PLLI2S | RCC_PERIPHCLK_LTDC | RCC_PERIPHCLK_TIM | RCC_PERIPHCLK_RTC; /* Get the PLLI2S Clock configuration -----------------------------------------------*/ PeriphClkInit->PLLI2S.PLLI2SN = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> RCC_PLLI2SCFGR_PLLI2SN_Pos); PeriphClkInit->PLLI2S.PLLI2SR = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> RCC_PLLI2SCFGR_PLLI2SR_Pos); PeriphClkInit->PLLI2S.PLLI2SQ = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SQ) >> RCC_PLLI2SCFGR_PLLI2SQ_Pos); /* Get the PLLSAI Clock configuration -----------------------------------------------*/ PeriphClkInit->PLLSAI.PLLSAIN = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIN) >> RCC_PLLSAICFGR_PLLSAIN_Pos); PeriphClkInit->PLLSAI.PLLSAIR = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIR) >> RCC_PLLSAICFGR_PLLSAIR_Pos); PeriphClkInit->PLLSAI.PLLSAIQ = (uint32_t)((RCC->PLLSAICFGR & RCC_PLLSAICFGR_PLLSAIQ) >> RCC_PLLSAICFGR_PLLSAIQ_Pos); /* Get the PLLSAI/PLLI2S division factors -----------------------------------------------*/ PeriphClkInit->PLLI2SDivQ = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLI2SDIVQ) >> RCC_DCKCFGR_PLLI2SDIVQ_Pos); PeriphClkInit->PLLSAIDivQ = (uint32_t)((RCC->DCKCFGR & RCC_DCKCFGR_PLLSAIDIVQ) >> RCC_DCKCFGR_PLLSAIDIVQ_Pos); PeriphClkInit->PLLSAIDivR = (uint32_t)(RCC->DCKCFGR & RCC_DCKCFGR_PLLSAIDIVR); /* Get the RTC Clock configuration -----------------------------------------------*/ tempreg = (RCC->CFGR & RCC_CFGR_RTCPRE); PeriphClkInit->RTCClockSelection = (uint32_t)((tempreg) | (RCC->BDCR & RCC_BDCR_RTCSEL)); if ((RCC->DCKCFGR & RCC_DCKCFGR_TIMPRE) == RESET) { PeriphClkInit->TIMPresSelection = RCC_TIMPRES_DESACTIVATED; } else { PeriphClkInit->TIMPresSelection = RCC_TIMPRES_ACTIVATED; } } /** * @brief Return the peripheral clock frequency for a given peripheral(SAI..) * @note Return 0 if peripheral clock identifier not managed by this API * @param PeriphClk Peripheral clock identifier * This parameter can be one of the following values: * @arg RCC_PERIPHCLK_I2S: I2S peripheral clock * @retval Frequency in KHz */ uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk) { /* This variable used to store the I2S clock frequency (value in Hz) */ uint32_t frequency = 0U; /* This variable used to store the VCO Input (value in Hz) */ uint32_t vcoinput = 0U; uint32_t srcclk = 0U; /* This variable used to store the VCO Output (value in Hz) */ uint32_t vcooutput = 0U; switch (PeriphClk) { case RCC_PERIPHCLK_I2S: { /* Get the current I2S source */ srcclk = __HAL_RCC_GET_I2S_SOURCE(); switch (srcclk) { /* Check if I2S clock selection is External clock mapped on the I2S_CKIN pin used as I2S clock */ case RCC_I2SCLKSOURCE_EXT: { /* Set the I2S clock to the external clock value */ frequency = EXTERNAL_CLOCK_VALUE; break; } /* Check if I2S clock selection is PLLI2S VCO output clock divided by PLLI2SR used as I2S clock */ case RCC_I2SCLKSOURCE_PLLI2S: { /* Configure the PLLI2S division factor */ /* PLLI2S_VCO Input = PLL_SOURCE/PLLM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } else { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ vcooutput = (uint32_t)(vcoinput * (((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> 6U) & (RCC_PLLI2SCFGR_PLLI2SN >> 6U))); /* I2S_CLK = PLLI2S_VCO Output/PLLI2SR */ frequency = (uint32_t)(vcooutput /(((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> 28U) & (RCC_PLLI2SCFGR_PLLI2SR >> 28U))); break; } /* Clock not enabled for I2S */ default: { frequency = 0U; break; } } break; } } return frequency; } #endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */ #if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) ||\ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) /** * @brief Initializes the RCC extended peripherals clocks according to the specified parameters in the * RCC_PeriphCLKInitTypeDef. * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that * contains the configuration information for the Extended Peripherals clocks(I2S and RTC clocks). * * @note A caution to be taken when HAL_RCCEx_PeriphCLKConfig() is used to select RTC clock selection, in this case * the Reset of Backup domain will be applied in order to modify the RTC Clock source as consequence all backup * domain (RTC and RCC_BDCR register expect BKPSRAM) will be reset * * @retval HAL status */ HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) { uint32_t tickstart = 0U; uint32_t tmpreg1 = 0U; /* Check the parameters */ assert_param(IS_RCC_PERIPHCLOCK(PeriphClkInit->PeriphClockSelection)); /*---------------------------- I2S configuration ---------------------------*/ if((((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_I2S) == RCC_PERIPHCLK_I2S) || (((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_PLLI2S) == RCC_PERIPHCLK_PLLI2S)) { /* check for Parameters */ assert_param(IS_RCC_PLLI2SR_VALUE(PeriphClkInit->PLLI2S.PLLI2SR)); assert_param(IS_RCC_PLLI2SN_VALUE(PeriphClkInit->PLLI2S.PLLI2SN)); #if defined(STM32F411xE) assert_param(IS_RCC_PLLI2SM_VALUE(PeriphClkInit->PLLI2S.PLLI2SM)); #endif /* STM32F411xE */ /* Disable the PLLI2S */ __HAL_RCC_PLLI2S_DISABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLI2S is disabled */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) { if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } #if defined(STM32F411xE) /* Configure the PLLI2S division factors */ /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM) */ /* I2SCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SR */ __HAL_RCC_PLLI2S_I2SCLK_CONFIG(PeriphClkInit->PLLI2S.PLLI2SM, PeriphClkInit->PLLI2S.PLLI2SN, PeriphClkInit->PLLI2S.PLLI2SR); #else /* Configure the PLLI2S division factors */ /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLM) */ /* I2SCLK = f(PLLI2S clock output) = f(VCO clock) / PLLI2SR */ __HAL_RCC_PLLI2S_CONFIG(PeriphClkInit->PLLI2S.PLLI2SN , PeriphClkInit->PLLI2S.PLLI2SR); #endif /* STM32F411xE */ /* Enable the PLLI2S */ __HAL_RCC_PLLI2S_ENABLE(); /* Get tick */ tickstart = HAL_GetTick(); /* Wait till PLLI2S is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) { if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } } /*---------------------------- RTC configuration ---------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_RTC) == (RCC_PERIPHCLK_RTC)) { /* Check for RTC Parameters used to output RTCCLK */ assert_param(IS_RCC_RTCCLKSOURCE(PeriphClkInit->RTCClockSelection)); /* Enable Power Clock*/ __HAL_RCC_PWR_CLK_ENABLE(); /* Enable write access to Backup domain */ PWR->CR |= PWR_CR_DBP; /* Get tick */ tickstart = HAL_GetTick(); while((PWR->CR & PWR_CR_DBP) == RESET) { if((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } /* Reset the Backup domain only if the RTC Clock source selection is modified from reset value */ tmpreg1 = (RCC->BDCR & RCC_BDCR_RTCSEL); if((tmpreg1 != 0x00000000U) && ((tmpreg1) != (PeriphClkInit->RTCClockSelection & RCC_BDCR_RTCSEL))) { /* Store the content of BDCR register before the reset of Backup Domain */ tmpreg1 = (RCC->BDCR & ~(RCC_BDCR_RTCSEL)); /* RTC Clock selection can be changed only if the Backup Domain is reset */ __HAL_RCC_BACKUPRESET_FORCE(); __HAL_RCC_BACKUPRESET_RELEASE(); /* Restore the Content of BDCR register */ RCC->BDCR = tmpreg1; /* Wait for LSE reactivation if LSE was enable prior to Backup Domain reset */ if(HAL_IS_BIT_SET(RCC->BDCR, RCC_BDCR_LSEON)) { /* Get tick */ tickstart = HAL_GetTick(); /* Wait till LSE is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) { if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } } __HAL_RCC_RTC_CONFIG(PeriphClkInit->RTCClockSelection); } #if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) /*---------------------------- TIM configuration ---------------------------*/ if(((PeriphClkInit->PeriphClockSelection) & RCC_PERIPHCLK_TIM) == (RCC_PERIPHCLK_TIM)) { __HAL_RCC_TIMCLKPRESCALER(PeriphClkInit->TIMPresSelection); } #endif /* STM32F401xC || STM32F401xE || STM32F411xE */ return HAL_OK; } /** * @brief Configures the RCC_OscInitStruct according to the internal * RCC configuration registers. * @param PeriphClkInit pointer to an RCC_PeriphCLKInitTypeDef structure that * will be configured. * @retval None */ void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit) { uint32_t tempreg; /* Set all possible values for the extended clock type parameter------------*/ PeriphClkInit->PeriphClockSelection = RCC_PERIPHCLK_I2S | RCC_PERIPHCLK_RTC; /* Get the PLLI2S Clock configuration --------------------------------------*/ PeriphClkInit->PLLI2S.PLLI2SN = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> RCC_PLLI2SCFGR_PLLI2SN_Pos); PeriphClkInit->PLLI2S.PLLI2SR = (uint32_t)((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> RCC_PLLI2SCFGR_PLLI2SR_Pos); #if defined(STM32F411xE) PeriphClkInit->PLLI2S.PLLI2SM = (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM); #endif /* STM32F411xE */ /* Get the RTC Clock configuration -----------------------------------------*/ tempreg = (RCC->CFGR & RCC_CFGR_RTCPRE); PeriphClkInit->RTCClockSelection = (uint32_t)((tempreg) | (RCC->BDCR & RCC_BDCR_RTCSEL)); #if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) /* Get the TIM Prescaler configuration -------------------------------------*/ if ((RCC->DCKCFGR & RCC_DCKCFGR_TIMPRE) == RESET) { PeriphClkInit->TIMPresSelection = RCC_TIMPRES_DESACTIVATED; } else { PeriphClkInit->TIMPresSelection = RCC_TIMPRES_ACTIVATED; } #endif /* STM32F401xC || STM32F401xE || STM32F411xE */ } /** * @brief Return the peripheral clock frequency for a given peripheral(SAI..) * @note Return 0 if peripheral clock identifier not managed by this API * @param PeriphClk Peripheral clock identifier * This parameter can be one of the following values: * @arg RCC_PERIPHCLK_I2S: I2S peripheral clock * @retval Frequency in KHz */ uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk) { /* This variable used to store the I2S clock frequency (value in Hz) */ uint32_t frequency = 0U; /* This variable used to store the VCO Input (value in Hz) */ uint32_t vcoinput = 0U; uint32_t srcclk = 0U; /* This variable used to store the VCO Output (value in Hz) */ uint32_t vcooutput = 0U; switch (PeriphClk) { case RCC_PERIPHCLK_I2S: { /* Get the current I2S source */ srcclk = __HAL_RCC_GET_I2S_SOURCE(); switch (srcclk) { /* Check if I2S clock selection is External clock mapped on the I2S_CKIN pin used as I2S clock */ case RCC_I2SCLKSOURCE_EXT: { /* Set the I2S clock to the external clock value */ frequency = EXTERNAL_CLOCK_VALUE; break; } /* Check if I2S clock selection is PLLI2S VCO output clock divided by PLLI2SR used as I2S clock */ case RCC_I2SCLKSOURCE_PLLI2S: { #if defined(STM32F411xE) /* Configure the PLLI2S division factor */ /* PLLI2S_VCO Input = PLL_SOURCE/PLLI2SM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSE_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); } else { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSI_VALUE / (uint32_t)(RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SM)); } #else /* Configure the PLLI2S division factor */ /* PLLI2S_VCO Input = PLL_SOURCE/PLLM */ if((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLSOURCE_HSE) { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSE_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } else { /* Get the I2S source clock value */ vcoinput = (uint32_t)(HSI_VALUE / (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM)); } #endif /* STM32F411xE */ /* PLLI2S_VCO Output = PLLI2S_VCO Input * PLLI2SN */ vcooutput = (uint32_t)(vcoinput * (((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SN) >> 6U) & (RCC_PLLI2SCFGR_PLLI2SN >> 6U))); /* I2S_CLK = PLLI2S_VCO Output/PLLI2SR */ frequency = (uint32_t)(vcooutput /(((RCC->PLLI2SCFGR & RCC_PLLI2SCFGR_PLLI2SR) >> 28U) & (RCC_PLLI2SCFGR_PLLI2SR >> 28U))); break; } /* Clock not enabled for I2S*/ default: { frequency = 0U; break; } } break; } } return frequency; } #endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE */ #if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) ||\ defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) || defined(STM32F413xx) || defined(STM32F423xx) /** * @brief Select LSE mode * * @note This mode is only available for STM32F410xx/STM32F411xx/STM32F446xx/STM32F469xx/STM32F479xx/STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx devices. * * @param Mode specifies the LSE mode. * This parameter can be one of the following values: * @arg RCC_LSE_LOWPOWER_MODE: LSE oscillator in low power mode selection * @arg RCC_LSE_HIGHDRIVE_MODE: LSE oscillator in High Drive mode selection * @retval None */ void HAL_RCCEx_SelectLSEMode(uint8_t Mode) { /* Check the parameters */ assert_param(IS_RCC_LSE_MODE(Mode)); if(Mode == RCC_LSE_HIGHDRIVE_MODE) { SET_BIT(RCC->BDCR, RCC_BDCR_LSEMOD); } else { CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEMOD); } } #endif /* STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx || STM32F413xx || STM32F423xx */ /** @defgroup RCCEx_Exported_Functions_Group2 Extended Clock management functions * @brief Extended Clock management functions * @verbatim =============================================================================== ##### Extended clock management functions ##### =============================================================================== [..] This subsection provides a set of functions allowing to control the activation or deactivation of PLLI2S, PLLSAI. @endverbatim * @{ */ #if defined(RCC_PLLI2S_SUPPORT) /** * @brief Enable PLLI2S. * @param PLLI2SInit pointer to an RCC_PLLI2SInitTypeDef structure that * contains the configuration information for the PLLI2S * @retval HAL status */ HAL_StatusTypeDef HAL_RCCEx_EnablePLLI2S(RCC_PLLI2SInitTypeDef *PLLI2SInit) { uint32_t tickstart; /* Check for parameters */ assert_param(IS_RCC_PLLI2SN_VALUE(PLLI2SInit->PLLI2SN)); assert_param(IS_RCC_PLLI2SR_VALUE(PLLI2SInit->PLLI2SR)); #if defined(RCC_PLLI2SCFGR_PLLI2SM) assert_param(IS_RCC_PLLI2SM_VALUE(PLLI2SInit->PLLI2SM)); #endif /* RCC_PLLI2SCFGR_PLLI2SM */ #if defined(RCC_PLLI2SCFGR_PLLI2SP) assert_param(IS_RCC_PLLI2SP_VALUE(PLLI2SInit->PLLI2SP)); #endif /* RCC_PLLI2SCFGR_PLLI2SP */ #if defined(RCC_PLLI2SCFGR_PLLI2SQ) assert_param(IS_RCC_PLLI2SQ_VALUE(PLLI2SInit->PLLI2SQ)); #endif /* RCC_PLLI2SCFGR_PLLI2SQ */ /* Disable the PLLI2S */ __HAL_RCC_PLLI2S_DISABLE(); /* Wait till PLLI2S is disabled */ tickstart = HAL_GetTick(); while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) != RESET) { if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } /* Configure the PLLI2S division factors */ #if defined(STM32F446xx) /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM) */ /* I2SPCLK = PLLI2S_VCO / PLLI2SP */ /* I2SQCLK = PLLI2S_VCO / PLLI2SQ */ /* I2SRCLK = PLLI2S_VCO / PLLI2SR */ __HAL_RCC_PLLI2S_CONFIG(PLLI2SInit->PLLI2SM, PLLI2SInit->PLLI2SN, \ PLLI2SInit->PLLI2SP, PLLI2SInit->PLLI2SQ, PLLI2SInit->PLLI2SR); #elif defined(STM32F412Zx) || defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) ||\ defined(STM32F413xx) || defined(STM32F423xx) /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM)*/ /* I2SQCLK = PLLI2S_VCO / PLLI2SQ */ /* I2SRCLK = PLLI2S_VCO / PLLI2SR */ __HAL_RCC_PLLI2S_CONFIG(PLLI2SInit->PLLI2SM, PLLI2SInit->PLLI2SN, \ PLLI2SInit->PLLI2SQ, PLLI2SInit->PLLI2SR); #elif defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ defined(STM32F469xx) || defined(STM32F479xx) /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * PLLI2SN */ /* I2SQCLK = PLLI2S_VCO / PLLI2SQ */ /* I2SRCLK = PLLI2S_VCO / PLLI2SR */ __HAL_RCC_PLLI2S_SAICLK_CONFIG(PLLI2SInit->PLLI2SN, PLLI2SInit->PLLI2SQ, PLLI2SInit->PLLI2SR); #elif defined(STM32F411xE) /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) * (PLLI2SN/PLLI2SM) */ /* I2SRCLK = PLLI2S_VCO / PLLI2SR */ __HAL_RCC_PLLI2S_I2SCLK_CONFIG(PLLI2SInit->PLLI2SM, PLLI2SInit->PLLI2SN, PLLI2SInit->PLLI2SR); #else /* PLLI2S_VCO = f(VCO clock) = f(PLLI2S clock input) x PLLI2SN */ /* I2SRCLK = PLLI2S_VCO / PLLI2SR */ __HAL_RCC_PLLI2S_CONFIG(PLLI2SInit->PLLI2SN, PLLI2SInit->PLLI2SR); #endif /* STM32F446xx */ /* Enable the PLLI2S */ __HAL_RCC_PLLI2S_ENABLE(); /* Wait till PLLI2S is ready */ tickstart = HAL_GetTick(); while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLI2SRDY) == RESET) { if((HAL_GetTick() - tickstart ) > PLLI2S_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } return HAL_OK; } /** * @brief Disable PLLI2S. * @retval HAL status */ HAL_StatusTypeDef HAL_RCCEx_DisablePLLI2S(void) { uint32_t tickstart; /* Disable the PLLI2S */ __HAL_RCC_PLLI2S_DISABLE(); /* Wait till PLLI2S is disabled */ tickstart = HAL_GetTick(); while(READ_BIT(RCC->CR, RCC_CR_PLLI2SRDY) != RESET) { if((HAL_GetTick() - tickstart) > PLLI2S_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } return HAL_OK; } #endif /* RCC_PLLI2S_SUPPORT */ #if defined(RCC_PLLSAI_SUPPORT) /** * @brief Enable PLLSAI. * @param PLLSAIInit pointer to an RCC_PLLSAIInitTypeDef structure that * contains the configuration information for the PLLSAI * @retval HAL status */ HAL_StatusTypeDef HAL_RCCEx_EnablePLLSAI(RCC_PLLSAIInitTypeDef *PLLSAIInit) { uint32_t tickstart; /* Check for parameters */ assert_param(IS_RCC_PLLSAIN_VALUE(PLLSAIInit->PLLSAIN)); assert_param(IS_RCC_PLLSAIQ_VALUE(PLLSAIInit->PLLSAIQ)); #if defined(RCC_PLLSAICFGR_PLLSAIM) assert_param(IS_RCC_PLLSAIM_VALUE(PLLSAIInit->PLLSAIM)); #endif /* RCC_PLLSAICFGR_PLLSAIM */ #if defined(RCC_PLLSAICFGR_PLLSAIP) assert_param(IS_RCC_PLLSAIP_VALUE(PLLSAIInit->PLLSAIP)); #endif /* RCC_PLLSAICFGR_PLLSAIP */ #if defined(RCC_PLLSAICFGR_PLLSAIR) assert_param(IS_RCC_PLLSAIR_VALUE(PLLSAIInit->PLLSAIR)); #endif /* RCC_PLLSAICFGR_PLLSAIR */ /* Disable the PLLSAI */ __HAL_RCC_PLLSAI_DISABLE(); /* Wait till PLLSAI is disabled */ tickstart = HAL_GetTick(); while(__HAL_RCC_PLLSAI_GET_FLAG() != RESET) { if((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } /* Configure the PLLSAI division factors */ #if defined(STM32F446xx) /* PLLSAI_VCO = f(VCO clock) = f(PLLSAI clock input) * (PLLSAIN/PLLSAIM) */ /* SAIPCLK = PLLSAI_VCO / PLLSAIP */ /* SAIQCLK = PLLSAI_VCO / PLLSAIQ */ /* SAIRCLK = PLLSAI_VCO / PLLSAIR */ __HAL_RCC_PLLSAI_CONFIG(PLLSAIInit->PLLSAIM, PLLSAIInit->PLLSAIN, \ PLLSAIInit->PLLSAIP, PLLSAIInit->PLLSAIQ, 0U); #elif defined(STM32F469xx) || defined(STM32F479xx) /* PLLSAI_VCO = f(VCO clock) = f(PLLSAI clock input) * PLLSAIN */ /* SAIPCLK = PLLSAI_VCO / PLLSAIP */ /* SAIQCLK = PLLSAI_VCO / PLLSAIQ */ /* SAIRCLK = PLLSAI_VCO / PLLSAIR */ __HAL_RCC_PLLSAI_CONFIG(PLLSAIInit->PLLSAIN, PLLSAIInit->PLLSAIP, \ PLLSAIInit->PLLSAIQ, PLLSAIInit->PLLSAIR); #else /* PLLSAI_VCO = f(VCO clock) = f(PLLSAI clock input) x PLLSAIN */ /* SAIQCLK = PLLSAI_VCO / PLLSAIQ */ /* SAIRCLK = PLLSAI_VCO / PLLSAIR */ __HAL_RCC_PLLSAI_CONFIG(PLLSAIInit->PLLSAIN, PLLSAIInit->PLLSAIQ, PLLSAIInit->PLLSAIR); #endif /* STM32F446xx */ /* Enable the PLLSAI */ __HAL_RCC_PLLSAI_ENABLE(); /* Wait till PLLSAI is ready */ tickstart = HAL_GetTick(); while(__HAL_RCC_PLLSAI_GET_FLAG() == RESET) { if((HAL_GetTick() - tickstart ) > PLLSAI_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } return HAL_OK; } /** * @brief Disable PLLSAI. * @retval HAL status */ HAL_StatusTypeDef HAL_RCCEx_DisablePLLSAI(void) { uint32_t tickstart; /* Disable the PLLSAI */ __HAL_RCC_PLLSAI_DISABLE(); /* Wait till PLLSAI is disabled */ tickstart = HAL_GetTick(); while(__HAL_RCC_PLLSAI_GET_FLAG() != RESET) { if((HAL_GetTick() - tickstart) > PLLSAI_TIMEOUT_VALUE) { /* return in case of Timeout detected */ return HAL_TIMEOUT; } } return HAL_OK; } #endif /* RCC_PLLSAI_SUPPORT */ /** * @} */ #if defined(STM32F446xx) /** * @brief Returns the SYSCLK frequency * * @note This function implementation is valid only for STM32F446xx devices. * @note This function add the PLL/PLLR System clock source * * @note The system frequency computed by this function is not the real * frequency in the chip. It is calculated based on the predefined * constant and the selected clock source: * @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*) * @note If SYSCLK source is HSE, function returns values based on HSE_VALUE(**) * @note If SYSCLK source is PLL or PLLR, function returns values based on HSE_VALUE(**) * or HSI_VALUE(*) multiplied/divided by the PLL factors. * @note (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value * 16 MHz) but the real value may vary depending on the variations * in voltage and temperature. * @note (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value * 25 MHz), user has to ensure that HSE_VALUE is same as the real * frequency of the crystal used. Otherwise, this function may * have wrong result. * * @note The result of this function could be not correct when using fractional * value for HSE crystal. * * @note This function can be used by the user application to compute the * baudrate for the communication peripherals or configure other parameters. * * @note Each time SYSCLK changes, this function must be called to update the * right SYSCLK value. Otherwise, any configuration based on this function will be incorrect. * * * @retval SYSCLK frequency */ uint32_t HAL_RCC_GetSysClockFreq(void) { uint32_t pllm = 0U; uint32_t pllvco = 0U; uint32_t pllp = 0U; uint32_t pllr = 0U; uint32_t sysclockfreq = 0U; /* Get SYSCLK source -------------------------------------------------------*/ switch (RCC->CFGR & RCC_CFGR_SWS) { case RCC_CFGR_SWS_HSI: /* HSI used as system clock source */ { sysclockfreq = HSI_VALUE; break; } case RCC_CFGR_SWS_HSE: /* HSE used as system clock source */ { sysclockfreq = HSE_VALUE; break; } case RCC_CFGR_SWS_PLL: /* PLL/PLLP used as system clock source */ { /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLLM) * PLLN SYSCLK = PLL_VCO / PLLP */ pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM; if(__HAL_RCC_GET_PLL_OSCSOURCE() != RCC_PLLSOURCE_HSI) { /* HSE used as PLL clock source */ pllvco = (uint32_t) ((((uint64_t) HSE_VALUE * ((uint64_t) ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos)))) / (uint64_t)pllm); } else { /* HSI used as PLL clock source */ pllvco = (uint32_t) ((((uint64_t) HSI_VALUE * ((uint64_t) ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos)))) / (uint64_t)pllm); } pllp = ((((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >> RCC_PLLCFGR_PLLP_Pos) + 1U) *2U); sysclockfreq = pllvco/pllp; break; } case RCC_CFGR_SWS_PLLR: /* PLL/PLLR used as system clock source */ { /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLLM) * PLLN SYSCLK = PLL_VCO / PLLR */ pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM; if(__HAL_RCC_GET_PLL_OSCSOURCE() != RCC_PLLSOURCE_HSI) { /* HSE used as PLL clock source */ pllvco = (uint32_t) ((((uint64_t) HSE_VALUE * ((uint64_t) ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos)))) / (uint64_t)pllm); } else { /* HSI used as PLL clock source */ pllvco = (uint32_t) ((((uint64_t) HSI_VALUE * ((uint64_t) ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos)))) / (uint64_t)pllm); } pllr = ((RCC->PLLCFGR & RCC_PLLCFGR_PLLR) >> RCC_PLLCFGR_PLLR_Pos); sysclockfreq = pllvco/pllr; break; } default: { sysclockfreq = HSI_VALUE; break; } } return sysclockfreq; } #endif /* STM32F446xx */ /** * @} */ /** * @} */ /** * @brief Resets the RCC clock configuration to the default reset state. * @note The default reset state of the clock configuration is given below: * - HSI ON and used as system clock source * - HSE, PLL, PLLI2S and PLLSAI OFF * - AHB, APB1 and APB2 prescaler set to 1. * - CSS, MCO1 and MCO2 OFF * - All interrupts disabled * @note This function doesn't modify the configuration of the * - Peripheral clocks * - LSI, LSE and RTC clocks * @retval HAL status */ HAL_StatusTypeDef HAL_RCC_DeInit(void) { uint32_t tickstart; /* Get Start Tick */ tickstart = HAL_GetTick(); /* Set HSION bit to the reset value */ SET_BIT(RCC->CR, RCC_CR_HSION); /* Wait till HSI is ready */ while (READ_BIT(RCC->CR, RCC_CR_HSIRDY) == RESET) { if ((HAL_GetTick() - tickstart) > HSI_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } /* Set HSITRIM[4:0] bits to the reset value */ SET_BIT(RCC->CR, RCC_CR_HSITRIM_4); /* Get Start Tick */ tickstart = HAL_GetTick(); /* Reset CFGR register */ CLEAR_REG(RCC->CFGR); /* Wait till clock switch is ready */ while (READ_BIT(RCC->CFGR, RCC_CFGR_SWS) != RESET) { if ((HAL_GetTick() - tickstart) > CLOCKSWITCH_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } /* Get Start Tick */ tickstart = HAL_GetTick(); /* Clear HSEON, HSEBYP and CSSON bits */ CLEAR_BIT(RCC->CR, RCC_CR_HSEON | RCC_CR_HSEBYP | RCC_CR_CSSON); /* Wait till HSE is disabled */ while (READ_BIT(RCC->CR, RCC_CR_HSERDY) != RESET) { if ((HAL_GetTick() - tickstart) > HSE_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } /* Get Start Tick */ tickstart = HAL_GetTick(); /* Clear PLLON bit */ CLEAR_BIT(RCC->CR, RCC_CR_PLLON); /* Wait till PLL is disabled */ while (READ_BIT(RCC->CR, RCC_CR_PLLRDY) != RESET) { if ((HAL_GetTick() - tickstart) > PLL_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } #if defined(RCC_PLLI2S_SUPPORT) /* Get Start Tick */ tickstart = HAL_GetTick(); /* Reset PLLI2SON bit */ CLEAR_BIT(RCC->CR, RCC_CR_PLLI2SON); /* Wait till PLLI2S is disabled */ while (READ_BIT(RCC->CR, RCC_CR_PLLI2SRDY) != RESET) { if ((HAL_GetTick() - tickstart) > PLLI2S_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } #endif /* RCC_PLLI2S_SUPPORT */ #if defined(RCC_PLLSAI_SUPPORT) /* Get Start Tick */ tickstart = HAL_GetTick(); /* Reset PLLSAI bit */ CLEAR_BIT(RCC->CR, RCC_CR_PLLSAION); /* Wait till PLLSAI is disabled */ while (READ_BIT(RCC->CR, RCC_CR_PLLSAIRDY) != RESET) { if ((HAL_GetTick() - tickstart) > PLLSAI_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } #endif /* RCC_PLLSAI_SUPPORT */ /* Once PLL, PLLI2S and PLLSAI are OFF, reset PLLCFGR register to default value */ #if defined(STM32F412Cx) || defined(STM32F412Rx) || defined(STM32F412Vx) || defined(STM32F412Zx) || defined(STM32F413xx) || \ defined(STM32F423xx) || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) RCC->PLLCFGR = RCC_PLLCFGR_PLLM_4 | RCC_PLLCFGR_PLLN_6 | RCC_PLLCFGR_PLLN_7 | RCC_PLLCFGR_PLLQ_2 | RCC_PLLCFGR_PLLR_1; #elif defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) RCC->PLLCFGR = RCC_PLLCFGR_PLLR_0 | RCC_PLLCFGR_PLLR_1 | RCC_PLLCFGR_PLLR_2 | RCC_PLLCFGR_PLLM_4 | RCC_PLLCFGR_PLLN_6 | RCC_PLLCFGR_PLLN_7 | RCC_PLLCFGR_PLLQ_0 | RCC_PLLCFGR_PLLQ_1 | RCC_PLLCFGR_PLLQ_2 | RCC_PLLCFGR_PLLQ_3; #else RCC->PLLCFGR = RCC_PLLCFGR_PLLM_4 | RCC_PLLCFGR_PLLN_6 | RCC_PLLCFGR_PLLN_7 | RCC_PLLCFGR_PLLQ_2; #endif /* STM32F412Cx || STM32F412Rx || STM32F412Vx || STM32F412Zx || STM32F413xx || STM32F423xx || STM32F446xx || STM32F469xx || STM32F479xx */ /* Reset PLLI2SCFGR register to default value */ #if defined(STM32F412Cx) || defined(STM32F412Rx) || defined(STM32F412Vx) || defined(STM32F412Zx) || defined(STM32F413xx) || \ defined(STM32F423xx) || defined(STM32F446xx) RCC->PLLI2SCFGR = RCC_PLLI2SCFGR_PLLI2SM_4 | RCC_PLLI2SCFGR_PLLI2SN_6 | RCC_PLLI2SCFGR_PLLI2SN_7 | RCC_PLLI2SCFGR_PLLI2SQ_2 | RCC_PLLI2SCFGR_PLLI2SR_1; #elif defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) RCC->PLLI2SCFGR = RCC_PLLI2SCFGR_PLLI2SN_6 | RCC_PLLI2SCFGR_PLLI2SN_7 | RCC_PLLI2SCFGR_PLLI2SR_1; #elif defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) RCC->PLLI2SCFGR = RCC_PLLI2SCFGR_PLLI2SN_6 | RCC_PLLI2SCFGR_PLLI2SN_7 | RCC_PLLI2SCFGR_PLLI2SQ_2 | RCC_PLLI2SCFGR_PLLI2SR_1; #elif defined(STM32F411xE) RCC->PLLI2SCFGR = RCC_PLLI2SCFGR_PLLI2SM_4 | RCC_PLLI2SCFGR_PLLI2SN_6 | RCC_PLLI2SCFGR_PLLI2SN_7 | RCC_PLLI2SCFGR_PLLI2SR_1; #endif /* STM32F412Cx || STM32F412Rx || STM32F412Vx || STM32F412Zx || STM32F413xx || STM32F423xx || STM32F446xx */ /* Reset PLLSAICFGR register */ #if defined(STM32F427xx) || defined(STM32F429xx) || defined(STM32F437xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) RCC->PLLSAICFGR = RCC_PLLSAICFGR_PLLSAIN_6 | RCC_PLLSAICFGR_PLLSAIN_7 | RCC_PLLSAICFGR_PLLSAIQ_2 | RCC_PLLSAICFGR_PLLSAIR_1; #elif defined(STM32F446xx) RCC->PLLSAICFGR = RCC_PLLSAICFGR_PLLSAIM_4 | RCC_PLLSAICFGR_PLLSAIN_6 | RCC_PLLSAICFGR_PLLSAIN_7 | RCC_PLLSAICFGR_PLLSAIQ_2; #endif /* STM32F427xx || STM32F429xx || STM32F437xx || STM32F439xx || STM32F469xx || STM32F479xx */ /* Disable all interrupts */ CLEAR_BIT(RCC->CIR, RCC_CIR_LSIRDYIE | RCC_CIR_LSERDYIE | RCC_CIR_HSIRDYIE | RCC_CIR_HSERDYIE | RCC_CIR_PLLRDYIE); #if defined(RCC_CIR_PLLI2SRDYIE) CLEAR_BIT(RCC->CIR, RCC_CIR_PLLI2SRDYIE); #endif /* RCC_CIR_PLLI2SRDYIE */ #if defined(RCC_CIR_PLLSAIRDYIE) CLEAR_BIT(RCC->CIR, RCC_CIR_PLLSAIRDYIE); #endif /* RCC_CIR_PLLSAIRDYIE */ /* Clear all interrupt flags */ SET_BIT(RCC->CIR, RCC_CIR_LSIRDYC | RCC_CIR_LSERDYC | RCC_CIR_HSIRDYC | RCC_CIR_HSERDYC | RCC_CIR_PLLRDYC | RCC_CIR_CSSC); #if defined(RCC_CIR_PLLI2SRDYC) SET_BIT(RCC->CIR, RCC_CIR_PLLI2SRDYC); #endif /* RCC_CIR_PLLI2SRDYC */ #if defined(RCC_CIR_PLLSAIRDYC) SET_BIT(RCC->CIR, RCC_CIR_PLLSAIRDYC); #endif /* RCC_CIR_PLLSAIRDYC */ /* Clear LSION bit */ CLEAR_BIT(RCC->CSR, RCC_CSR_LSION); /* Reset all CSR flags */ SET_BIT(RCC->CSR, RCC_CSR_RMVF); /* Update the SystemCoreClock global variable */ SystemCoreClock = HSI_VALUE; /* Adapt Systick interrupt period */ if(HAL_InitTick(TICK_INT_PRIORITY) != HAL_OK) { return HAL_ERROR; } else { return HAL_OK; } } #if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) ||\ defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) || defined(STM32F413xx) || defined(STM32F423xx) /** * @brief Initializes the RCC Oscillators according to the specified parameters in the * RCC_OscInitTypeDef. * @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that * contains the configuration information for the RCC Oscillators. * @note The PLL is not disabled when used as system clock. * @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not * supported by this API. User should request a transition to LSE Off * first and then LSE On or LSE Bypass. * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not * supported by this API. User should request a transition to HSE Off * first and then HSE On or HSE Bypass. * @note This function add the PLL/PLLR factor management during PLL configuration this feature * is only available in STM32F410xx/STM32F446xx/STM32F469xx/STM32F479xx/STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx devices * @retval HAL status */ HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct) { uint32_t tickstart = 0U; /* Check the parameters */ assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType)); /*------------------------------- HSE Configuration ------------------------*/ if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) { /* Check the parameters */ assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState)); /* When the HSE is used as system clock or clock source for PLL in these cases HSE will not disabled */ #if defined(STM32F446xx) if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSE) ||\ ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSE)) ||\ ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLLR) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSE))) #else if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSE) ||\ ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSE))) #endif /* STM32F446xx */ { if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) && (RCC_OscInitStruct->HSEState == RCC_HSE_OFF)) { return HAL_ERROR; } } else { /* Set the new HSE configuration ---------------------------------------*/ __HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState); /* Check the HSE State */ if((RCC_OscInitStruct->HSEState) != RCC_HSE_OFF) { /* Get Start Tick*/ tickstart = HAL_GetTick(); /* Wait till HSE is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) { if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } else { /* Get Start Tick*/ tickstart = HAL_GetTick(); /* Wait till HSE is bypassed or disabled */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) { if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } } } /*----------------------------- HSI Configuration --------------------------*/ if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) { /* Check the parameters */ assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState)); assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue)); /* Check if HSI is used as system clock or as PLL source when PLL is selected as system clock */ #if defined(STM32F446xx) if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSI) ||\ ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSI)) ||\ ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLLR) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSI))) #else if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSI) ||\ ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSI))) #endif /* STM32F446xx */ { /* When HSI is used as system clock it will not disabled */ if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON)) { return HAL_ERROR; } /* Otherwise, just the calibration is allowed */ else { /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); } } else { /* Check the HSI State */ if((RCC_OscInitStruct->HSIState)!= RCC_HSI_OFF) { /* Enable the Internal High Speed oscillator (HSI). */ __HAL_RCC_HSI_ENABLE(); /* Get Start Tick*/ tickstart = HAL_GetTick(); /* Wait till HSI is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) { if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); } else { /* Disable the Internal High Speed oscillator (HSI). */ __HAL_RCC_HSI_DISABLE(); /* Get Start Tick*/ tickstart = HAL_GetTick(); /* Wait till HSI is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) { if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } } } /*------------------------------ LSI Configuration -------------------------*/ if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) { /* Check the parameters */ assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState)); /* Check the LSI State */ if((RCC_OscInitStruct->LSIState)!= RCC_LSI_OFF) { /* Enable the Internal Low Speed oscillator (LSI). */ __HAL_RCC_LSI_ENABLE(); /* Get Start Tick*/ tickstart = HAL_GetTick(); /* Wait till LSI is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == RESET) { if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } else { /* Disable the Internal Low Speed oscillator (LSI). */ __HAL_RCC_LSI_DISABLE(); /* Get Start Tick*/ tickstart = HAL_GetTick(); /* Wait till LSI is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != RESET) { if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } } /*------------------------------ LSE Configuration -------------------------*/ if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE) { FlagStatus pwrclkchanged = RESET; /* Check the parameters */ assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState)); /* Update LSE configuration in Backup Domain control register */ /* Requires to enable write access to Backup Domain of necessary */ if(__HAL_RCC_PWR_IS_CLK_DISABLED()) { __HAL_RCC_PWR_CLK_ENABLE(); pwrclkchanged = SET; } if(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP)) { /* Enable write access to Backup domain */ SET_BIT(PWR->CR, PWR_CR_DBP); /* Wait for Backup domain Write protection disable */ tickstart = HAL_GetTick(); while(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP)) { if((HAL_GetTick() - tickstart) > RCC_DBP_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } /* Set the new LSE configuration -----------------------------------------*/ __HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState); /* Check the LSE State */ if((RCC_OscInitStruct->LSEState) != RCC_LSE_OFF) { /* Get Start Tick*/ tickstart = HAL_GetTick(); /* Wait till LSE is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) { if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } else { /* Get Start Tick*/ tickstart = HAL_GetTick(); /* Wait till LSE is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET) { if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } /* Restore clock configuration if changed */ if(pwrclkchanged == SET) { __HAL_RCC_PWR_CLK_DISABLE(); } } /*-------------------------------- PLL Configuration -----------------------*/ /* Check the parameters */ assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState)); if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE) { /* Check if the PLL is used as system clock or not */ if(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_PLL) { if((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON) { /* Check the parameters */ assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource)); assert_param(IS_RCC_PLLM_VALUE(RCC_OscInitStruct->PLL.PLLM)); assert_param(IS_RCC_PLLN_VALUE(RCC_OscInitStruct->PLL.PLLN)); assert_param(IS_RCC_PLLP_VALUE(RCC_OscInitStruct->PLL.PLLP)); assert_param(IS_RCC_PLLQ_VALUE(RCC_OscInitStruct->PLL.PLLQ)); assert_param(IS_RCC_PLLR_VALUE(RCC_OscInitStruct->PLL.PLLR)); /* Disable the main PLL. */ __HAL_RCC_PLL_DISABLE(); /* Get Start Tick*/ tickstart = HAL_GetTick(); /* Wait till PLL is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) { if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } /* Configure the main PLL clock source, multiplication and division factors. */ __HAL_RCC_PLL_CONFIG(RCC_OscInitStruct->PLL.PLLSource, RCC_OscInitStruct->PLL.PLLM, RCC_OscInitStruct->PLL.PLLN, RCC_OscInitStruct->PLL.PLLP, RCC_OscInitStruct->PLL.PLLQ, RCC_OscInitStruct->PLL.PLLR); /* Enable the main PLL. */ __HAL_RCC_PLL_ENABLE(); /* Get Start Tick*/ tickstart = HAL_GetTick(); /* Wait till PLL is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) { if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } else { /* Disable the main PLL. */ __HAL_RCC_PLL_DISABLE(); /* Get Start Tick*/ tickstart = HAL_GetTick(); /* Wait till PLL is ready */ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) { if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } } else { return HAL_ERROR; } } return HAL_OK; } /** * @brief Configures the RCC_OscInitStruct according to the internal * RCC configuration registers. * @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that will be configured. * * @note This function is only available in case of STM32F410xx/STM32F446xx/STM32F469xx/STM32F479xx/STM32F412Zx/STM32F412Vx/STM32F412Rx/STM32F412Cx devices. * @note This function add the PLL/PLLR factor management * @retval None */ void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct) { /* Set all possible values for the Oscillator type parameter ---------------*/ RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_LSI; /* Get the HSE configuration -----------------------------------------------*/ if((RCC->CR &RCC_CR_HSEBYP) == RCC_CR_HSEBYP) { RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS; } else if((RCC->CR &RCC_CR_HSEON) == RCC_CR_HSEON) { RCC_OscInitStruct->HSEState = RCC_HSE_ON; } else { RCC_OscInitStruct->HSEState = RCC_HSE_OFF; } /* Get the HSI configuration -----------------------------------------------*/ if((RCC->CR &RCC_CR_HSION) == RCC_CR_HSION) { RCC_OscInitStruct->HSIState = RCC_HSI_ON; } else { RCC_OscInitStruct->HSIState = RCC_HSI_OFF; } RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->CR &RCC_CR_HSITRIM) >> RCC_CR_HSITRIM_Pos); /* Get the LSE configuration -----------------------------------------------*/ if((RCC->BDCR &RCC_BDCR_LSEBYP) == RCC_BDCR_LSEBYP) { RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS; } else if((RCC->BDCR &RCC_BDCR_LSEON) == RCC_BDCR_LSEON) { RCC_OscInitStruct->LSEState = RCC_LSE_ON; } else { RCC_OscInitStruct->LSEState = RCC_LSE_OFF; } /* Get the LSI configuration -----------------------------------------------*/ if((RCC->CSR &RCC_CSR_LSION) == RCC_CSR_LSION) { RCC_OscInitStruct->LSIState = RCC_LSI_ON; } else { RCC_OscInitStruct->LSIState = RCC_LSI_OFF; } /* Get the PLL configuration -----------------------------------------------*/ if((RCC->CR &RCC_CR_PLLON) == RCC_CR_PLLON) { RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON; } else { RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF; } RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC); RCC_OscInitStruct->PLL.PLLM = (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM); RCC_OscInitStruct->PLL.PLLN = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos); RCC_OscInitStruct->PLL.PLLP = (uint32_t)((((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) + RCC_PLLCFGR_PLLP_0) << 1U) >> RCC_PLLCFGR_PLLP_Pos); RCC_OscInitStruct->PLL.PLLQ = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLQ) >> RCC_PLLCFGR_PLLQ_Pos); RCC_OscInitStruct->PLL.PLLR = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLR) >> RCC_PLLCFGR_PLLR_Pos); } #endif /* STM32F410xx || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx || STM32F413xx || STM32F423xx */ #endif /* HAL_RCC_MODULE_ENABLED */ /** * @} */ /** * @} */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/