Mercurial > public > ostc4
view Common/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc.h @ 199:ac58a9fb92ac div-fixes-cleaup-2
Bugfix: fix initial CNS data in the logbook header
Apparently, there has been confusion in the past about the data format of the
CNS data in the logbook. This seems to be partially fixed back in 2015, but
this fix forgot that the initial CNS data is also in the logbook header.
So, now, the logbook header also stores the initial CNS data in a correct way,
which fixes the problem of strange CNS values at the very start of repetitive
dives, that get reset in the dive profile after the first CNS sample data comes
along.
Signed-off-by: Jan Mulder <jlmulder@xs4all.nl>
| author | Jan Mulder <jlmulder@xs4all.nl> |
|---|---|
| date | Fri, 22 Mar 2019 08:36:39 +0100 |
| parents | c78bcbd5deda |
| children |
line wrap: on
line source
/** ****************************************************************************** * @file stm32f4xx_hal_rcc.h * @author MCD Application Team * @brief Header file of RCC HAL module. ****************************************************************************** * @attention * * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2> * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef __STM32F4xx_HAL_RCC_H #define __STM32F4xx_HAL_RCC_H #ifdef __cplusplus extern "C" { #endif /* Includes ------------------------------------------------------------------*/ #include "stm32f4xx_hal_def.h" /* Include RCC HAL Extended module */ /* (include on top of file since RCC structures are defined in extended file) */ #include "stm32f4xx_hal_rcc_ex.h" /** @addtogroup STM32F4xx_HAL_Driver * @{ */ /** @addtogroup RCC * @{ */ /* Exported types ------------------------------------------------------------*/ /** @defgroup RCC_Exported_Types RCC Exported Types * @{ */ /** * @brief RCC Internal/External Oscillator (HSE, HSI, LSE and LSI) configuration structure definition */ typedef struct { uint32_t OscillatorType; /*!< The oscillators to be configured. This parameter can be a value of @ref RCC_Oscillator_Type */ uint32_t HSEState; /*!< The new state of the HSE. This parameter can be a value of @ref RCC_HSE_Config */ uint32_t LSEState; /*!< The new state of the LSE. This parameter can be a value of @ref RCC_LSE_Config */ uint32_t HSIState; /*!< The new state of the HSI. This parameter can be a value of @ref RCC_HSI_Config */ uint32_t HSICalibrationValue; /*!< The HSI calibration trimming value (default is RCC_HSICALIBRATION_DEFAULT). This parameter must be a number between Min_Data = 0x00 and Max_Data = 0x1F */ uint32_t LSIState; /*!< The new state of the LSI. This parameter can be a value of @ref RCC_LSI_Config */ RCC_PLLInitTypeDef PLL; /*!< PLL structure parameters */ }RCC_OscInitTypeDef; /** * @brief RCC System, AHB and APB busses clock configuration structure definition */ typedef struct { uint32_t ClockType; /*!< The clock to be configured. This parameter can be a value of @ref RCC_System_Clock_Type */ uint32_t SYSCLKSource; /*!< The clock source (SYSCLKS) used as system clock. This parameter can be a value of @ref RCC_System_Clock_Source */ uint32_t AHBCLKDivider; /*!< The AHB clock (HCLK) divider. This clock is derived from the system clock (SYSCLK). This parameter can be a value of @ref RCC_AHB_Clock_Source */ uint32_t APB1CLKDivider; /*!< The APB1 clock (PCLK1) divider. This clock is derived from the AHB clock (HCLK). This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */ uint32_t APB2CLKDivider; /*!< The APB2 clock (PCLK2) divider. This clock is derived from the AHB clock (HCLK). This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */ }RCC_ClkInitTypeDef; /** * @} */ /* Exported constants --------------------------------------------------------*/ /** @defgroup RCC_Exported_Constants RCC Exported Constants * @{ */ /** @defgroup RCC_Oscillator_Type Oscillator Type * @{ */ #define RCC_OSCILLATORTYPE_NONE 0x00000000U #define RCC_OSCILLATORTYPE_HSE 0x00000001U #define RCC_OSCILLATORTYPE_HSI 0x00000002U #define RCC_OSCILLATORTYPE_LSE 0x00000004U #define RCC_OSCILLATORTYPE_LSI 0x00000008U /** * @} */ /** @defgroup RCC_HSE_Config HSE Config * @{ */ #define RCC_HSE_OFF 0x00000000U #define RCC_HSE_ON RCC_CR_HSEON #define RCC_HSE_BYPASS ((uint32_t)(RCC_CR_HSEBYP | RCC_CR_HSEON)) /** * @} */ /** @defgroup RCC_LSE_Config LSE Config * @{ */ #define RCC_LSE_OFF 0x00000000U #define RCC_LSE_ON RCC_BDCR_LSEON #define RCC_LSE_BYPASS ((uint32_t)(RCC_BDCR_LSEBYP | RCC_BDCR_LSEON)) /** * @} */ /** @defgroup RCC_HSI_Config HSI Config * @{ */ #define RCC_HSI_OFF ((uint8_t)0x00) #define RCC_HSI_ON ((uint8_t)0x01) #define RCC_HSICALIBRATION_DEFAULT 0x10U /* Default HSI calibration trimming value */ /** * @} */ /** @defgroup RCC_LSI_Config LSI Config * @{ */ #define RCC_LSI_OFF ((uint8_t)0x00) #define RCC_LSI_ON ((uint8_t)0x01) /** * @} */ /** @defgroup RCC_PLL_Config PLL Config * @{ */ #define RCC_PLL_NONE ((uint8_t)0x00) #define RCC_PLL_OFF ((uint8_t)0x01) #define RCC_PLL_ON ((uint8_t)0x02) /** * @} */ /** @defgroup RCC_PLLP_Clock_Divider PLLP Clock Divider * @{ */ #define RCC_PLLP_DIV2 0x00000002U #define RCC_PLLP_DIV4 0x00000004U #define RCC_PLLP_DIV6 0x00000006U #define RCC_PLLP_DIV8 0x00000008U /** * @} */ /** @defgroup RCC_PLL_Clock_Source PLL Clock Source * @{ */ #define RCC_PLLSOURCE_HSI RCC_PLLCFGR_PLLSRC_HSI #define RCC_PLLSOURCE_HSE RCC_PLLCFGR_PLLSRC_HSE /** * @} */ /** @defgroup RCC_System_Clock_Type System Clock Type * @{ */ #define RCC_CLOCKTYPE_SYSCLK 0x00000001U #define RCC_CLOCKTYPE_HCLK 0x00000002U #define RCC_CLOCKTYPE_PCLK1 0x00000004U #define RCC_CLOCKTYPE_PCLK2 0x00000008U /** * @} */ /** @defgroup RCC_System_Clock_Source System Clock Source * @note The RCC_SYSCLKSOURCE_PLLRCLK parameter is available only for * STM32F446xx devices. * @{ */ #define RCC_SYSCLKSOURCE_HSI RCC_CFGR_SW_HSI #define RCC_SYSCLKSOURCE_HSE RCC_CFGR_SW_HSE #define RCC_SYSCLKSOURCE_PLLCLK RCC_CFGR_SW_PLL #define RCC_SYSCLKSOURCE_PLLRCLK ((uint32_t)(RCC_CFGR_SW_0 | RCC_CFGR_SW_1)) /** * @} */ /** @defgroup RCC_System_Clock_Source_Status System Clock Source Status * @note The RCC_SYSCLKSOURCE_STATUS_PLLRCLK parameter is available only for * STM32F446xx devices. * @{ */ #define RCC_SYSCLKSOURCE_STATUS_HSI RCC_CFGR_SWS_HSI /*!< HSI used as system clock */ #define RCC_SYSCLKSOURCE_STATUS_HSE RCC_CFGR_SWS_HSE /*!< HSE used as system clock */ #define RCC_SYSCLKSOURCE_STATUS_PLLCLK RCC_CFGR_SWS_PLL /*!< PLL used as system clock */ #define RCC_SYSCLKSOURCE_STATUS_PLLRCLK ((uint32_t)(RCC_CFGR_SWS_0 | RCC_CFGR_SWS_1)) /*!< PLLR used as system clock */ /** * @} */ /** @defgroup RCC_AHB_Clock_Source AHB Clock Source * @{ */ #define RCC_SYSCLK_DIV1 RCC_CFGR_HPRE_DIV1 #define RCC_SYSCLK_DIV2 RCC_CFGR_HPRE_DIV2 #define RCC_SYSCLK_DIV4 RCC_CFGR_HPRE_DIV4 #define RCC_SYSCLK_DIV8 RCC_CFGR_HPRE_DIV8 #define RCC_SYSCLK_DIV16 RCC_CFGR_HPRE_DIV16 #define RCC_SYSCLK_DIV64 RCC_CFGR_HPRE_DIV64 #define RCC_SYSCLK_DIV128 RCC_CFGR_HPRE_DIV128 #define RCC_SYSCLK_DIV256 RCC_CFGR_HPRE_DIV256 #define RCC_SYSCLK_DIV512 RCC_CFGR_HPRE_DIV512 /** * @} */ /** @defgroup RCC_APB1_APB2_Clock_Source APB1/APB2 Clock Source * @{ */ #define RCC_HCLK_DIV1 RCC_CFGR_PPRE1_DIV1 #define RCC_HCLK_DIV2 RCC_CFGR_PPRE1_DIV2 #define RCC_HCLK_DIV4 RCC_CFGR_PPRE1_DIV4 #define RCC_HCLK_DIV8 RCC_CFGR_PPRE1_DIV8 #define RCC_HCLK_DIV16 RCC_CFGR_PPRE1_DIV16 /** * @} */ /** @defgroup RCC_RTC_Clock_Source RTC Clock Source * @{ */ #define RCC_RTCCLKSOURCE_NO_CLK 0x00000000U #define RCC_RTCCLKSOURCE_LSE 0x00000100U #define RCC_RTCCLKSOURCE_LSI 0x00000200U #define RCC_RTCCLKSOURCE_HSE_DIVX 0x00000300U #define RCC_RTCCLKSOURCE_HSE_DIV2 0x00020300U #define RCC_RTCCLKSOURCE_HSE_DIV3 0x00030300U #define RCC_RTCCLKSOURCE_HSE_DIV4 0x00040300U #define RCC_RTCCLKSOURCE_HSE_DIV5 0x00050300U #define RCC_RTCCLKSOURCE_HSE_DIV6 0x00060300U #define RCC_RTCCLKSOURCE_HSE_DIV7 0x00070300U #define RCC_RTCCLKSOURCE_HSE_DIV8 0x00080300U #define RCC_RTCCLKSOURCE_HSE_DIV9 0x00090300U #define RCC_RTCCLKSOURCE_HSE_DIV10 0x000A0300U #define RCC_RTCCLKSOURCE_HSE_DIV11 0x000B0300U #define RCC_RTCCLKSOURCE_HSE_DIV12 0x000C0300U #define RCC_RTCCLKSOURCE_HSE_DIV13 0x000D0300U #define RCC_RTCCLKSOURCE_HSE_DIV14 0x000E0300U #define RCC_RTCCLKSOURCE_HSE_DIV15 0x000F0300U #define RCC_RTCCLKSOURCE_HSE_DIV16 0x00100300U #define RCC_RTCCLKSOURCE_HSE_DIV17 0x00110300U #define RCC_RTCCLKSOURCE_HSE_DIV18 0x00120300U #define RCC_RTCCLKSOURCE_HSE_DIV19 0x00130300U #define RCC_RTCCLKSOURCE_HSE_DIV20 0x00140300U #define RCC_RTCCLKSOURCE_HSE_DIV21 0x00150300U #define RCC_RTCCLKSOURCE_HSE_DIV22 0x00160300U #define RCC_RTCCLKSOURCE_HSE_DIV23 0x00170300U #define RCC_RTCCLKSOURCE_HSE_DIV24 0x00180300U #define RCC_RTCCLKSOURCE_HSE_DIV25 0x00190300U #define RCC_RTCCLKSOURCE_HSE_DIV26 0x001A0300U #define RCC_RTCCLKSOURCE_HSE_DIV27 0x001B0300U #define RCC_RTCCLKSOURCE_HSE_DIV28 0x001C0300U #define RCC_RTCCLKSOURCE_HSE_DIV29 0x001D0300U #define RCC_RTCCLKSOURCE_HSE_DIV30 0x001E0300U #define RCC_RTCCLKSOURCE_HSE_DIV31 0x001F0300U /** * @} */ /** @defgroup RCC_MCO_Index MCO Index * @{ */ #define RCC_MCO1 0x00000000U #define RCC_MCO2 0x00000001U /** * @} */ /** @defgroup RCC_MCO1_Clock_Source MCO1 Clock Source * @{ */ #define RCC_MCO1SOURCE_HSI 0x00000000U #define RCC_MCO1SOURCE_LSE RCC_CFGR_MCO1_0 #define RCC_MCO1SOURCE_HSE RCC_CFGR_MCO1_1 #define RCC_MCO1SOURCE_PLLCLK RCC_CFGR_MCO1 /** * @} */ /** @defgroup RCC_MCOx_Clock_Prescaler MCOx Clock Prescaler * @{ */ #define RCC_MCODIV_1 0x00000000U #define RCC_MCODIV_2 RCC_CFGR_MCO1PRE_2 #define RCC_MCODIV_3 ((uint32_t)RCC_CFGR_MCO1PRE_0 | RCC_CFGR_MCO1PRE_2) #define RCC_MCODIV_4 ((uint32_t)RCC_CFGR_MCO1PRE_1 | RCC_CFGR_MCO1PRE_2) #define RCC_MCODIV_5 RCC_CFGR_MCO1PRE /** * @} */ /** @defgroup RCC_Interrupt Interrupts * @{ */ #define RCC_IT_LSIRDY ((uint8_t)0x01) #define RCC_IT_LSERDY ((uint8_t)0x02) #define RCC_IT_HSIRDY ((uint8_t)0x04) #define RCC_IT_HSERDY ((uint8_t)0x08) #define RCC_IT_PLLRDY ((uint8_t)0x10) #define RCC_IT_PLLI2SRDY ((uint8_t)0x20) #define RCC_IT_CSS ((uint8_t)0x80) /** * @} */ /** @defgroup RCC_Flag Flags * Elements values convention: 0XXYYYYYb * - YYYYY : Flag position in the register * - 0XX : Register index * - 01: CR register * - 10: BDCR register * - 11: CSR register * @{ */ /* Flags in the CR register */ #define RCC_FLAG_HSIRDY ((uint8_t)0x21) #define RCC_FLAG_HSERDY ((uint8_t)0x31) #define RCC_FLAG_PLLRDY ((uint8_t)0x39) #define RCC_FLAG_PLLI2SRDY ((uint8_t)0x3B) /* Flags in the BDCR register */ #define RCC_FLAG_LSERDY ((uint8_t)0x41) /* Flags in the CSR register */ #define RCC_FLAG_LSIRDY ((uint8_t)0x61) #define RCC_FLAG_BORRST ((uint8_t)0x79) #define RCC_FLAG_PINRST ((uint8_t)0x7A) #define RCC_FLAG_PORRST ((uint8_t)0x7B) #define RCC_FLAG_SFTRST ((uint8_t)0x7C) #define RCC_FLAG_IWDGRST ((uint8_t)0x7D) #define RCC_FLAG_WWDGRST ((uint8_t)0x7E) #define RCC_FLAG_LPWRRST ((uint8_t)0x7F) /** * @} */ /** * @} */ /* Exported macro ------------------------------------------------------------*/ /** @defgroup RCC_Exported_Macros RCC Exported Macros * @{ */ /** @defgroup RCC_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable * @brief Enable or disable the AHB1 peripheral clock. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_GPIOA_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOAEN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOAEN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_GPIOB_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOBEN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOBEN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_GPIOC_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_GPIOH_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOHEN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOHEN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_DMA1_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_DMA2_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_GPIOA_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOAEN)) #define __HAL_RCC_GPIOB_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOBEN)) #define __HAL_RCC_GPIOC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOCEN)) #define __HAL_RCC_GPIOH_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOHEN)) #define __HAL_RCC_DMA1_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_DMA1EN)) #define __HAL_RCC_DMA2_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_DMA2EN)) /** * @} */ /** @defgroup RCC_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enable Disable Status * @brief Get the enable or disable status of the AHB1 peripheral clock. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_GPIOA_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOAEN)) != RESET) #define __HAL_RCC_GPIOB_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOBEN)) != RESET) #define __HAL_RCC_GPIOC_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOCEN)) != RESET) #define __HAL_RCC_GPIOH_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOHEN)) != RESET) #define __HAL_RCC_DMA1_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_DMA1EN)) != RESET) #define __HAL_RCC_DMA2_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_DMA2EN)) != RESET) #define __HAL_RCC_GPIOA_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOAEN)) == RESET) #define __HAL_RCC_GPIOB_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOBEN)) == RESET) #define __HAL_RCC_GPIOC_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOCEN)) == RESET) #define __HAL_RCC_GPIOH_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOHEN)) == RESET) #define __HAL_RCC_DMA1_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_DMA1EN)) == RESET) #define __HAL_RCC_DMA2_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_DMA2EN)) == RESET) /** * @} */ /** @defgroup RCC_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable * @brief Enable or disable the Low Speed APB (APB1) peripheral clock. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_TIM5_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM5EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM5EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_WWDG_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_SPI2_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI2EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI2EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_USART2_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_USART2EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_USART2EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_I2C1_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_I2C2_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C2EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C2EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_PWR_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_TIM5_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM5EN)) #define __HAL_RCC_WWDG_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_WWDGEN)) #define __HAL_RCC_SPI2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI2EN)) #define __HAL_RCC_USART2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USART2EN)) #define __HAL_RCC_I2C1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C1EN)) #define __HAL_RCC_I2C2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C2EN)) #define __HAL_RCC_PWR_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_PWREN)) /** * @} */ /** @defgroup RCC_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status * @brief Get the enable or disable status of the APB1 peripheral clock. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_TIM5_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM5EN)) != RESET) #define __HAL_RCC_WWDG_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) != RESET) #define __HAL_RCC_SPI2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI2EN)) != RESET) #define __HAL_RCC_USART2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART2EN)) != RESET) #define __HAL_RCC_I2C1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) != RESET) #define __HAL_RCC_I2C2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C2EN)) != RESET) #define __HAL_RCC_PWR_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) != RESET) #define __HAL_RCC_TIM5_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM5EN)) == RESET) #define __HAL_RCC_WWDG_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) == RESET) #define __HAL_RCC_SPI2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI2EN)) == RESET) #define __HAL_RCC_USART2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART2EN)) == RESET) #define __HAL_RCC_I2C1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) == RESET) #define __HAL_RCC_I2C2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C2EN)) == RESET) #define __HAL_RCC_PWR_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) == RESET) /** * @} */ /** @defgroup RCC_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable * @brief Enable or disable the High Speed APB (APB2) peripheral clock. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_TIM1_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_USART1_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_USART6_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_USART6EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART6EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_ADC1_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_SPI1_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_SYSCFG_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_TIM9_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM9EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM9EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_TIM11_CLK_ENABLE() do { \ __IO uint32_t tmpreg = 0x00U; \ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM11EN);\ /* Delay after an RCC peripheral clock enabling */ \ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM11EN);\ UNUSED(tmpreg); \ } while(0U) #define __HAL_RCC_TIM1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM1EN)) #define __HAL_RCC_USART1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_USART1EN)) #define __HAL_RCC_USART6_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_USART6EN)) #define __HAL_RCC_ADC1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC1EN)) #define __HAL_RCC_SPI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI1EN)) #define __HAL_RCC_SYSCFG_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SYSCFGEN)) #define __HAL_RCC_TIM9_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM9EN)) #define __HAL_RCC_TIM11_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM11EN)) /** * @} */ /** @defgroup RCC_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status * @brief Get the enable or disable status of the APB2 peripheral clock. * @note After reset, the peripheral clock (used for registers read/write access) * is disabled and the application software has to enable this clock before * using it. * @{ */ #define __HAL_RCC_TIM1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) != RESET) #define __HAL_RCC_USART1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) != RESET) #define __HAL_RCC_USART6_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART6EN)) != RESET) #define __HAL_RCC_ADC1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) != RESET) #define __HAL_RCC_SPI1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) != RESET) #define __HAL_RCC_SYSCFG_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SYSCFGEN)) != RESET) #define __HAL_RCC_TIM9_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM9EN)) != RESET) #define __HAL_RCC_TIM11_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM11EN)) != RESET) #define __HAL_RCC_TIM1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) == RESET) #define __HAL_RCC_USART1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) == RESET) #define __HAL_RCC_USART6_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART6EN)) == RESET) #define __HAL_RCC_ADC1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) == RESET) #define __HAL_RCC_SPI1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) == RESET) #define __HAL_RCC_SYSCFG_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SYSCFGEN)) == RESET) #define __HAL_RCC_TIM9_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM9EN)) == RESET) #define __HAL_RCC_TIM11_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM11EN)) == RESET) /** * @} */ /** @defgroup RCC_AHB1_Force_Release_Reset AHB1 Force Release Reset * @brief Force or release AHB1 peripheral reset. * @{ */ #define __HAL_RCC_AHB1_FORCE_RESET() (RCC->AHB1RSTR = 0xFFFFFFFFU) #define __HAL_RCC_GPIOA_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOARST)) #define __HAL_RCC_GPIOB_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOBRST)) #define __HAL_RCC_GPIOC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOCRST)) #define __HAL_RCC_GPIOH_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOHRST)) #define __HAL_RCC_DMA1_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_DMA1RST)) #define __HAL_RCC_DMA2_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_DMA2RST)) #define __HAL_RCC_AHB1_RELEASE_RESET() (RCC->AHB1RSTR = 0x00U) #define __HAL_RCC_GPIOA_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOARST)) #define __HAL_RCC_GPIOB_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOBRST)) #define __HAL_RCC_GPIOC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOCRST)) #define __HAL_RCC_GPIOH_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOHRST)) #define __HAL_RCC_DMA1_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_DMA1RST)) #define __HAL_RCC_DMA2_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_DMA2RST)) /** * @} */ /** @defgroup RCC_APB1_Force_Release_Reset APB1 Force Release Reset * @brief Force or release APB1 peripheral reset. * @{ */ #define __HAL_RCC_APB1_FORCE_RESET() (RCC->APB1RSTR = 0xFFFFFFFFU) #define __HAL_RCC_TIM5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM5RST)) #define __HAL_RCC_WWDG_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_WWDGRST)) #define __HAL_RCC_SPI2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI2RST)) #define __HAL_RCC_USART2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART2RST)) #define __HAL_RCC_I2C1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C1RST)) #define __HAL_RCC_I2C2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C2RST)) #define __HAL_RCC_PWR_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_PWRRST)) #define __HAL_RCC_APB1_RELEASE_RESET() (RCC->APB1RSTR = 0x00U) #define __HAL_RCC_TIM5_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM5RST)) #define __HAL_RCC_WWDG_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_WWDGRST)) #define __HAL_RCC_SPI2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI2RST)) #define __HAL_RCC_USART2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USART2RST)) #define __HAL_RCC_I2C1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C1RST)) #define __HAL_RCC_I2C2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C2RST)) #define __HAL_RCC_PWR_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_PWRRST)) /** * @} */ /** @defgroup RCC_APB2_Force_Release_Reset APB2 Force Release Reset * @brief Force or release APB2 peripheral reset. * @{ */ #define __HAL_RCC_APB2_FORCE_RESET() (RCC->APB2RSTR = 0xFFFFFFFFU) #define __HAL_RCC_TIM1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM1RST)) #define __HAL_RCC_USART1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_USART1RST)) #define __HAL_RCC_USART6_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_USART6RST)) #define __HAL_RCC_ADC_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_ADCRST)) #define __HAL_RCC_SPI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI1RST)) #define __HAL_RCC_SYSCFG_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SYSCFGRST)) #define __HAL_RCC_TIM9_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM9RST)) #define __HAL_RCC_TIM11_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM11RST)) #define __HAL_RCC_APB2_RELEASE_RESET() (RCC->APB2RSTR = 0x00U) #define __HAL_RCC_TIM1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM1RST)) #define __HAL_RCC_USART1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_USART1RST)) #define __HAL_RCC_USART6_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_USART6RST)) #define __HAL_RCC_ADC_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_ADCRST)) #define __HAL_RCC_SPI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI1RST)) #define __HAL_RCC_SYSCFG_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SYSCFGRST)) #define __HAL_RCC_TIM9_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM9RST)) #define __HAL_RCC_TIM11_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM11RST)) /** * @} */ /** @defgroup RCC_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode. * @note Peripheral clock gating in SLEEP mode can be used to further reduce * power consumption. * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. * @note By default, all peripheral clocks are enabled during SLEEP mode. * @{ */ #define __HAL_RCC_GPIOA_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOALPEN)) #define __HAL_RCC_GPIOB_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOBLPEN)) #define __HAL_RCC_GPIOC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOCLPEN)) #define __HAL_RCC_GPIOH_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOHLPEN)) #define __HAL_RCC_DMA1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_DMA1LPEN)) #define __HAL_RCC_DMA2_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_DMA2LPEN)) #define __HAL_RCC_GPIOA_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOALPEN)) #define __HAL_RCC_GPIOB_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOBLPEN)) #define __HAL_RCC_GPIOC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOCLPEN)) #define __HAL_RCC_GPIOH_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOHLPEN)) #define __HAL_RCC_DMA1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_DMA1LPEN)) #define __HAL_RCC_DMA2_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_DMA2LPEN)) /** * @} */ /** @defgroup RCC_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode. * @note Peripheral clock gating in SLEEP mode can be used to further reduce * power consumption. * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. * @note By default, all peripheral clocks are enabled during SLEEP mode. * @{ */ #define __HAL_RCC_TIM5_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM5LPEN)) #define __HAL_RCC_WWDG_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_WWDGLPEN)) #define __HAL_RCC_SPI2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI2LPEN)) #define __HAL_RCC_USART2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_USART2LPEN)) #define __HAL_RCC_I2C1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C1LPEN)) #define __HAL_RCC_I2C2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C2LPEN)) #define __HAL_RCC_PWR_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_PWRLPEN)) #define __HAL_RCC_TIM5_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM5LPEN)) #define __HAL_RCC_WWDG_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_WWDGLPEN)) #define __HAL_RCC_SPI2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI2LPEN)) #define __HAL_RCC_USART2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_USART2LPEN)) #define __HAL_RCC_I2C1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C1LPEN)) #define __HAL_RCC_I2C2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C2LPEN)) #define __HAL_RCC_PWR_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_PWRLPEN)) /** * @} */ /** @defgroup RCC_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode. * @note Peripheral clock gating in SLEEP mode can be used to further reduce * power consumption. * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. * @note By default, all peripheral clocks are enabled during SLEEP mode. * @{ */ #define __HAL_RCC_TIM1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM1LPEN)) #define __HAL_RCC_USART1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_USART1LPEN)) #define __HAL_RCC_USART6_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_USART6LPEN)) #define __HAL_RCC_ADC1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC1LPEN)) #define __HAL_RCC_SPI1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI1LPEN)) #define __HAL_RCC_SYSCFG_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SYSCFGLPEN)) #define __HAL_RCC_TIM9_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM9LPEN)) #define __HAL_RCC_TIM11_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM11LPEN)) #define __HAL_RCC_TIM1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM1LPEN)) #define __HAL_RCC_USART1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_USART1LPEN)) #define __HAL_RCC_USART6_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_USART6LPEN)) #define __HAL_RCC_ADC1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC1LPEN)) #define __HAL_RCC_SPI1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI1LPEN)) #define __HAL_RCC_SYSCFG_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SYSCFGLPEN)) #define __HAL_RCC_TIM9_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM9LPEN)) #define __HAL_RCC_TIM11_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM11LPEN)) /** * @} */ /** @defgroup RCC_HSI_Configuration HSI Configuration * @{ */ /** @brief Macros to enable or disable the Internal High Speed oscillator (HSI). * @note The HSI is stopped by hardware when entering STOP and STANDBY modes. * It is used (enabled by hardware) as system clock source after startup * from Reset, wake-up from STOP and STANDBY mode, or in case of failure * of the HSE used directly or indirectly as system clock (if the Clock * Security System CSS is enabled). * @note HSI can not be stopped if it is used as system clock source. In this case, * you have to select another source of the system clock then stop the HSI. * @note After enabling the HSI, the application software should wait on HSIRDY * flag to be set indicating that HSI clock is stable and can be used as * system clock source. * This parameter can be: ENABLE or DISABLE. * @note When the HSI is stopped, HSIRDY flag goes low after 6 HSI oscillator * clock cycles. */ #define __HAL_RCC_HSI_ENABLE() (*(__IO uint32_t *) RCC_CR_HSION_BB = ENABLE) #define __HAL_RCC_HSI_DISABLE() (*(__IO uint32_t *) RCC_CR_HSION_BB = DISABLE) /** @brief Macro to adjust the Internal High Speed oscillator (HSI) calibration value. * @note The calibration is used to compensate for the variations in voltage * and temperature that influence the frequency of the internal HSI RC. * @param __HSICalibrationValue__ specifies the calibration trimming value. * (default is RCC_HSICALIBRATION_DEFAULT). * This parameter must be a number between 0 and 0x1F. */ #define __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(__HSICalibrationValue__) (MODIFY_REG(RCC->CR,\ RCC_CR_HSITRIM, (uint32_t)(__HSICalibrationValue__) << RCC_CR_HSITRIM_Pos)) /** * @} */ /** @defgroup RCC_LSI_Configuration LSI Configuration * @{ */ /** @brief Macros to enable or disable the Internal Low Speed oscillator (LSI). * @note After enabling the LSI, the application software should wait on * LSIRDY flag to be set indicating that LSI clock is stable and can * be used to clock the IWDG and/or the RTC. * @note LSI can not be disabled if the IWDG is running. * @note When the LSI is stopped, LSIRDY flag goes low after 6 LSI oscillator * clock cycles. */ #define __HAL_RCC_LSI_ENABLE() (*(__IO uint32_t *) RCC_CSR_LSION_BB = ENABLE) #define __HAL_RCC_LSI_DISABLE() (*(__IO uint32_t *) RCC_CSR_LSION_BB = DISABLE) /** * @} */ /** @defgroup RCC_HSE_Configuration HSE Configuration * @{ */ /** * @brief Macro to configure the External High Speed oscillator (HSE). * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not supported by this macro. * User should request a transition to HSE Off first and then HSE On or HSE Bypass. * @note After enabling the HSE (RCC_HSE_ON or RCC_HSE_Bypass), the application * software should wait on HSERDY flag to be set indicating that HSE clock * is stable and can be used to clock the PLL and/or system clock. * @note HSE state can not be changed if it is used directly or through the * PLL as system clock. In this case, you have to select another source * of the system clock then change the HSE state (ex. disable it). * @note The HSE is stopped by hardware when entering STOP and STANDBY modes. * @note This function reset the CSSON bit, so if the clock security system(CSS) * was previously enabled you have to enable it again after calling this * function. * @param __STATE__ specifies the new state of the HSE. * This parameter can be one of the following values: * @arg RCC_HSE_OFF: turn OFF the HSE oscillator, HSERDY flag goes low after * 6 HSE oscillator clock cycles. * @arg RCC_HSE_ON: turn ON the HSE oscillator. * @arg RCC_HSE_BYPASS: HSE oscillator bypassed with external clock. */ #define __HAL_RCC_HSE_CONFIG(__STATE__) \ do { \ if ((__STATE__) == RCC_HSE_ON) \ { \ SET_BIT(RCC->CR, RCC_CR_HSEON); \ } \ else if ((__STATE__) == RCC_HSE_BYPASS) \ { \ SET_BIT(RCC->CR, RCC_CR_HSEBYP); \ SET_BIT(RCC->CR, RCC_CR_HSEON); \ } \ else \ { \ CLEAR_BIT(RCC->CR, RCC_CR_HSEON); \ CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); \ } \ } while(0U) /** * @} */ /** @defgroup RCC_LSE_Configuration LSE Configuration * @{ */ /** * @brief Macro to configure the External Low Speed oscillator (LSE). * @note Transition LSE Bypass to LSE On and LSE On to LSE Bypass are not supported by this macro. * User should request a transition to LSE Off first and then LSE On or LSE Bypass. * @note As the LSE is in the Backup domain and write access is denied to * this domain after reset, you have to enable write access using * HAL_PWR_EnableBkUpAccess() function before to configure the LSE * (to be done once after reset). * @note After enabling the LSE (RCC_LSE_ON or RCC_LSE_BYPASS), the application * software should wait on LSERDY flag to be set indicating that LSE clock * is stable and can be used to clock the RTC. * @param __STATE__ specifies the new state of the LSE. * This parameter can be one of the following values: * @arg RCC_LSE_OFF: turn OFF the LSE oscillator, LSERDY flag goes low after * 6 LSE oscillator clock cycles. * @arg RCC_LSE_ON: turn ON the LSE oscillator. * @arg RCC_LSE_BYPASS: LSE oscillator bypassed with external clock. */ #define __HAL_RCC_LSE_CONFIG(__STATE__) \ do { \ if((__STATE__) == RCC_LSE_ON) \ { \ SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ } \ else if((__STATE__) == RCC_LSE_BYPASS) \ { \ SET_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \ SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ } \ else \ { \ CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \ } \ } while(0U) /** * @} */ /** @defgroup RCC_Internal_RTC_Clock_Configuration RTC Clock Configuration * @{ */ /** @brief Macros to enable or disable the RTC clock. * @note These macros must be used only after the RTC clock source was selected. */ #define __HAL_RCC_RTC_ENABLE() (*(__IO uint32_t *) RCC_BDCR_RTCEN_BB = ENABLE) #define __HAL_RCC_RTC_DISABLE() (*(__IO uint32_t *) RCC_BDCR_RTCEN_BB = DISABLE) /** @brief Macros to configure the RTC clock (RTCCLK). * @note As the RTC clock configuration bits are in the Backup domain and write * access is denied to this domain after reset, you have to enable write * access using the Power Backup Access macro before to configure * the RTC clock source (to be done once after reset). * @note Once the RTC clock is configured it can't be changed unless the * Backup domain is reset using __HAL_RCC_BackupReset_RELEASE() macro, or by * a Power On Reset (POR). * @param __RTCCLKSource__ specifies the RTC clock source. * This parameter can be one of the following values: @arg @ref RCC_RTCCLKSOURCE_NO_CLK: No clock selected as RTC clock. * @arg @ref RCC_RTCCLKSOURCE_LSE: LSE selected as RTC clock. * @arg @ref RCC_RTCCLKSOURCE_LSI: LSI selected as RTC clock. * @arg @ref RCC_RTCCLKSOURCE_HSE_DIVX: HSE clock divided by x selected * as RTC clock, where x:[2,31] * @note If the LSE or LSI is used as RTC clock source, the RTC continues to * work in STOP and STANDBY modes, and can be used as wake-up source. * However, when the HSE clock is used as RTC clock source, the RTC * cannot be used in STOP and STANDBY modes. * @note The maximum input clock frequency for RTC is 1MHz (when using HSE as * RTC clock source). */ #define __HAL_RCC_RTC_CLKPRESCALER(__RTCCLKSource__) (((__RTCCLKSource__) & RCC_BDCR_RTCSEL) == RCC_BDCR_RTCSEL) ? \ MODIFY_REG(RCC->CFGR, RCC_CFGR_RTCPRE, ((__RTCCLKSource__) & 0xFFFFCFFU)) : CLEAR_BIT(RCC->CFGR, RCC_CFGR_RTCPRE) #define __HAL_RCC_RTC_CONFIG(__RTCCLKSource__) do { __HAL_RCC_RTC_CLKPRESCALER(__RTCCLKSource__); \ RCC->BDCR |= ((__RTCCLKSource__) & 0x00000FFFU); \ } while(0U) /** @brief Macro to get the RTC clock source. * @retval The clock source can be one of the following values: * @arg @ref RCC_RTCCLKSOURCE_NO_CLK No clock selected as RTC clock * @arg @ref RCC_RTCCLKSOURCE_LSE LSE selected as RTC clock * @arg @ref RCC_RTCCLKSOURCE_LSI LSI selected as RTC clock * @arg @ref RCC_RTCCLKSOURCE_HSE_DIVX HSE divided by X selected as RTC clock (X can be retrieved thanks to @ref __HAL_RCC_GET_RTC_HSE_PRESCALER() */ #define __HAL_RCC_GET_RTC_SOURCE() (READ_BIT(RCC->BDCR, RCC_BDCR_RTCSEL)) /** * @brief Get the RTC and HSE clock divider (RTCPRE). * @retval Returned value can be one of the following values: * @arg @ref RCC_RTCCLKSOURCE_HSE_DIVX: HSE clock divided by x selected * as RTC clock, where x:[2,31] */ #define __HAL_RCC_GET_RTC_HSE_PRESCALER() (READ_BIT(RCC->CFGR, RCC_CFGR_RTCPRE) | RCC_BDCR_RTCSEL) /** @brief Macros to force or release the Backup domain reset. * @note This function resets the RTC peripheral (including the backup registers) * and the RTC clock source selection in RCC_CSR register. * @note The BKPSRAM is not affected by this reset. */ #define __HAL_RCC_BACKUPRESET_FORCE() (*(__IO uint32_t *) RCC_BDCR_BDRST_BB = ENABLE) #define __HAL_RCC_BACKUPRESET_RELEASE() (*(__IO uint32_t *) RCC_BDCR_BDRST_BB = DISABLE) /** * @} */ /** @defgroup RCC_PLL_Configuration PLL Configuration * @{ */ /** @brief Macros to enable or disable the main PLL. * @note After enabling the main PLL, the application software should wait on * PLLRDY flag to be set indicating that PLL clock is stable and can * be used as system clock source. * @note The main PLL can not be disabled if it is used as system clock source * @note The main PLL is disabled by hardware when entering STOP and STANDBY modes. */ #define __HAL_RCC_PLL_ENABLE() (*(__IO uint32_t *) RCC_CR_PLLON_BB = ENABLE) #define __HAL_RCC_PLL_DISABLE() (*(__IO uint32_t *) RCC_CR_PLLON_BB = DISABLE) /** @brief Macro to configure the PLL clock source. * @note This function must be used only when the main PLL is disabled. * @param __PLLSOURCE__ specifies the PLL entry clock source. * This parameter can be one of the following values: * @arg RCC_PLLSOURCE_HSI: HSI oscillator clock selected as PLL clock entry * @arg RCC_PLLSOURCE_HSE: HSE oscillator clock selected as PLL clock entry * */ #define __HAL_RCC_PLL_PLLSOURCE_CONFIG(__PLLSOURCE__) MODIFY_REG(RCC->PLLCFGR, RCC_PLLCFGR_PLLSRC, (__PLLSOURCE__)) /** @brief Macro to configure the PLL multiplication factor. * @note This function must be used only when the main PLL is disabled. * @param __PLLM__ specifies the division factor for PLL VCO input clock * This parameter must be a number between Min_Data = 2 and Max_Data = 63. * @note You have to set the PLLM parameter correctly to ensure that the VCO input * frequency ranges from 1 to 2 MHz. It is recommended to select a frequency * of 2 MHz to limit PLL jitter. * */ #define __HAL_RCC_PLL_PLLM_CONFIG(__PLLM__) MODIFY_REG(RCC->PLLCFGR, RCC_PLLCFGR_PLLM, (__PLLM__)) /** * @} */ /** @defgroup RCC_Get_Clock_source Get Clock source * @{ */ /** * @brief Macro to configure the system clock source. * @param __RCC_SYSCLKSOURCE__ specifies the system clock source. * This parameter can be one of the following values: * - RCC_SYSCLKSOURCE_HSI: HSI oscillator is used as system clock source. * - RCC_SYSCLKSOURCE_HSE: HSE oscillator is used as system clock source. * - RCC_SYSCLKSOURCE_PLLCLK: PLL output is used as system clock source. * - RCC_SYSCLKSOURCE_PLLRCLK: PLLR output is used as system clock source. This * parameter is available only for STM32F446xx devices. */ #define __HAL_RCC_SYSCLK_CONFIG(__RCC_SYSCLKSOURCE__) MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, (__RCC_SYSCLKSOURCE__)) /** @brief Macro to get the clock source used as system clock. * @retval The clock source used as system clock. The returned value can be one * of the following: * - RCC_SYSCLKSOURCE_STATUS_HSI: HSI used as system clock. * - RCC_SYSCLKSOURCE_STATUS_HSE: HSE used as system clock. * - RCC_SYSCLKSOURCE_STATUS_PLLCLK: PLL used as system clock. * - RCC_SYSCLKSOURCE_STATUS_PLLRCLK: PLLR used as system clock. This parameter * is available only for STM32F446xx devices. */ #define __HAL_RCC_GET_SYSCLK_SOURCE() (RCC->CFGR & RCC_CFGR_SWS) /** @brief Macro to get the oscillator used as PLL clock source. * @retval The oscillator used as PLL clock source. The returned value can be one * of the following: * - RCC_PLLSOURCE_HSI: HSI oscillator is used as PLL clock source. * - RCC_PLLSOURCE_HSE: HSE oscillator is used as PLL clock source. */ #define __HAL_RCC_GET_PLL_OSCSOURCE() ((uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC)) /** * @} */ /** @defgroup RCCEx_MCOx_Clock_Config RCC Extended MCOx Clock Config * @{ */ /** @brief Macro to configure the MCO1 clock. * @param __MCOCLKSOURCE__ specifies the MCO clock source. * This parameter can be one of the following values: * @arg RCC_MCO1SOURCE_HSI: HSI clock selected as MCO1 source * @arg RCC_MCO1SOURCE_LSE: LSE clock selected as MCO1 source * @arg RCC_MCO1SOURCE_HSE: HSE clock selected as MCO1 source * @arg RCC_MCO1SOURCE_PLLCLK: main PLL clock selected as MCO1 source * @param __MCODIV__ specifies the MCO clock prescaler. * This parameter can be one of the following values: * @arg RCC_MCODIV_1: no division applied to MCOx clock * @arg RCC_MCODIV_2: division by 2 applied to MCOx clock * @arg RCC_MCODIV_3: division by 3 applied to MCOx clock * @arg RCC_MCODIV_4: division by 4 applied to MCOx clock * @arg RCC_MCODIV_5: division by 5 applied to MCOx clock */ #define __HAL_RCC_MCO1_CONFIG(__MCOCLKSOURCE__, __MCODIV__) \ MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO1 | RCC_CFGR_MCO1PRE), ((__MCOCLKSOURCE__) | (__MCODIV__))) /** @brief Macro to configure the MCO2 clock. * @param __MCOCLKSOURCE__ specifies the MCO clock source. * This parameter can be one of the following values: * @arg RCC_MCO2SOURCE_SYSCLK: System clock (SYSCLK) selected as MCO2 source * @arg RCC_MCO2SOURCE_PLLI2SCLK: PLLI2S clock selected as MCO2 source, available for all STM32F4 devices except STM32F410xx * @arg RCC_MCO2SOURCE_I2SCLK: I2SCLK clock selected as MCO2 source, available only for STM32F410Rx devices * @arg RCC_MCO2SOURCE_HSE: HSE clock selected as MCO2 source * @arg RCC_MCO2SOURCE_PLLCLK: main PLL clock selected as MCO2 source * @param __MCODIV__ specifies the MCO clock prescaler. * This parameter can be one of the following values: * @arg RCC_MCODIV_1: no division applied to MCOx clock * @arg RCC_MCODIV_2: division by 2 applied to MCOx clock * @arg RCC_MCODIV_3: division by 3 applied to MCOx clock * @arg RCC_MCODIV_4: division by 4 applied to MCOx clock * @arg RCC_MCODIV_5: division by 5 applied to MCOx clock * @note For STM32F410Rx devices, to output I2SCLK clock on MCO2, you should have * at least one of the SPI clocks enabled (SPI1, SPI2 or SPI5). */ #define __HAL_RCC_MCO2_CONFIG(__MCOCLKSOURCE__, __MCODIV__) \ MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO2 | RCC_CFGR_MCO2PRE), ((__MCOCLKSOURCE__) | ((__MCODIV__) << 3U))); /** * @} */ /** @defgroup RCC_Flags_Interrupts_Management Flags Interrupts Management * @brief macros to manage the specified RCC Flags and interrupts. * @{ */ /** @brief Enable RCC interrupt (Perform Byte access to RCC_CIR[14:8] bits to enable * the selected interrupts). * @param __INTERRUPT__ specifies the RCC interrupt sources to be enabled. * This parameter can be any combination of the following values: * @arg RCC_IT_LSIRDY: LSI ready interrupt. * @arg RCC_IT_LSERDY: LSE ready interrupt. * @arg RCC_IT_HSIRDY: HSI ready interrupt. * @arg RCC_IT_HSERDY: HSE ready interrupt. * @arg RCC_IT_PLLRDY: Main PLL ready interrupt. * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt. */ #define __HAL_RCC_ENABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS |= (__INTERRUPT__)) /** @brief Disable RCC interrupt (Perform Byte access to RCC_CIR[14:8] bits to disable * the selected interrupts). * @param __INTERRUPT__ specifies the RCC interrupt sources to be disabled. * This parameter can be any combination of the following values: * @arg RCC_IT_LSIRDY: LSI ready interrupt. * @arg RCC_IT_LSERDY: LSE ready interrupt. * @arg RCC_IT_HSIRDY: HSI ready interrupt. * @arg RCC_IT_HSERDY: HSE ready interrupt. * @arg RCC_IT_PLLRDY: Main PLL ready interrupt. * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt. */ #define __HAL_RCC_DISABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS &= (uint8_t)(~(__INTERRUPT__))) /** @brief Clear the RCC's interrupt pending bits (Perform Byte access to RCC_CIR[23:16] * bits to clear the selected interrupt pending bits. * @param __INTERRUPT__ specifies the interrupt pending bit to clear. * This parameter can be any combination of the following values: * @arg RCC_IT_LSIRDY: LSI ready interrupt. * @arg RCC_IT_LSERDY: LSE ready interrupt. * @arg RCC_IT_HSIRDY: HSI ready interrupt. * @arg RCC_IT_HSERDY: HSE ready interrupt. * @arg RCC_IT_PLLRDY: Main PLL ready interrupt. * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt. * @arg RCC_IT_CSS: Clock Security System interrupt */ #define __HAL_RCC_CLEAR_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE2_ADDRESS = (__INTERRUPT__)) /** @brief Check the RCC's interrupt has occurred or not. * @param __INTERRUPT__ specifies the RCC interrupt source to check. * This parameter can be one of the following values: * @arg RCC_IT_LSIRDY: LSI ready interrupt. * @arg RCC_IT_LSERDY: LSE ready interrupt. * @arg RCC_IT_HSIRDY: HSI ready interrupt. * @arg RCC_IT_HSERDY: HSE ready interrupt. * @arg RCC_IT_PLLRDY: Main PLL ready interrupt. * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt. * @arg RCC_IT_CSS: Clock Security System interrupt * @retval The new state of __INTERRUPT__ (TRUE or FALSE). */ #define __HAL_RCC_GET_IT(__INTERRUPT__) ((RCC->CIR & (__INTERRUPT__)) == (__INTERRUPT__)) /** @brief Set RMVF bit to clear the reset flags: RCC_FLAG_PINRST, RCC_FLAG_PORRST, * RCC_FLAG_SFTRST, RCC_FLAG_IWDGRST, RCC_FLAG_WWDGRST and RCC_FLAG_LPWRRST. */ #define __HAL_RCC_CLEAR_RESET_FLAGS() (RCC->CSR |= RCC_CSR_RMVF) /** @brief Check RCC flag is set or not. * @param __FLAG__ specifies the flag to check. * This parameter can be one of the following values: * @arg RCC_FLAG_HSIRDY: HSI oscillator clock ready. * @arg RCC_FLAG_HSERDY: HSE oscillator clock ready. * @arg RCC_FLAG_PLLRDY: Main PLL clock ready. * @arg RCC_FLAG_PLLI2SRDY: PLLI2S clock ready. * @arg RCC_FLAG_LSERDY: LSE oscillator clock ready. * @arg RCC_FLAG_LSIRDY: LSI oscillator clock ready. * @arg RCC_FLAG_BORRST: POR/PDR or BOR reset. * @arg RCC_FLAG_PINRST: Pin reset. * @arg RCC_FLAG_PORRST: POR/PDR reset. * @arg RCC_FLAG_SFTRST: Software reset. * @arg RCC_FLAG_IWDGRST: Independent Watchdog reset. * @arg RCC_FLAG_WWDGRST: Window Watchdog reset. * @arg RCC_FLAG_LPWRRST: Low Power reset. * @retval The new state of __FLAG__ (TRUE or FALSE). */ #define RCC_FLAG_MASK ((uint8_t)0x1FU) #define __HAL_RCC_GET_FLAG(__FLAG__) (((((((__FLAG__) >> 5U) == 1U)? RCC->CR :((((__FLAG__) >> 5U) == 2U) ? RCC->BDCR :((((__FLAG__) >> 5U) == 3U)? RCC->CSR :RCC->CIR))) & (1U << ((__FLAG__) & RCC_FLAG_MASK)))!= 0U)? 1U : 0U) /** * @} */ /** * @} */ /* Exported functions --------------------------------------------------------*/ /** @addtogroup RCC_Exported_Functions * @{ */ /** @addtogroup RCC_Exported_Functions_Group1 * @{ */ /* Initialization and de-initialization functions ******************************/ HAL_StatusTypeDef HAL_RCC_DeInit(void); HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct); HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency); /** * @} */ /** @addtogroup RCC_Exported_Functions_Group2 * @{ */ /* Peripheral Control functions ************************************************/ void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv); void HAL_RCC_EnableCSS(void); void HAL_RCC_DisableCSS(void); uint32_t HAL_RCC_GetSysClockFreq(void); uint32_t HAL_RCC_GetHCLKFreq(void); uint32_t HAL_RCC_GetPCLK1Freq(void); uint32_t HAL_RCC_GetPCLK2Freq(void); void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct); void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency); /* CSS NMI IRQ handler */ void HAL_RCC_NMI_IRQHandler(void); /* User Callbacks in non blocking mode (IT mode) */ void HAL_RCC_CSSCallback(void); /** * @} */ /** * @} */ /* Private types -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Private constants ---------------------------------------------------------*/ /** @defgroup RCC_Private_Constants RCC Private Constants * @{ */ /** @defgroup RCC_BitAddress_AliasRegion RCC BitAddress AliasRegion * @brief RCC registers bit address in the alias region * @{ */ #define RCC_OFFSET (RCC_BASE - PERIPH_BASE) /* --- CR Register --- */ /* Alias word address of HSION bit */ #define RCC_CR_OFFSET (RCC_OFFSET + 0x00U) #define RCC_HSION_BIT_NUMBER 0x00U #define RCC_CR_HSION_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32U) + (RCC_HSION_BIT_NUMBER * 4U)) /* Alias word address of CSSON bit */ #define RCC_CSSON_BIT_NUMBER 0x13U #define RCC_CR_CSSON_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32U) + (RCC_CSSON_BIT_NUMBER * 4U)) /* Alias word address of PLLON bit */ #define RCC_PLLON_BIT_NUMBER 0x18U #define RCC_CR_PLLON_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32U) + (RCC_PLLON_BIT_NUMBER * 4U)) /* --- BDCR Register --- */ /* Alias word address of RTCEN bit */ #define RCC_BDCR_OFFSET (RCC_OFFSET + 0x70U) #define RCC_RTCEN_BIT_NUMBER 0x0FU #define RCC_BDCR_RTCEN_BB (PERIPH_BB_BASE + (RCC_BDCR_OFFSET * 32U) + (RCC_RTCEN_BIT_NUMBER * 4U)) /* Alias word address of BDRST bit */ #define RCC_BDRST_BIT_NUMBER 0x10U #define RCC_BDCR_BDRST_BB (PERIPH_BB_BASE + (RCC_BDCR_OFFSET * 32U) + (RCC_BDRST_BIT_NUMBER * 4U)) /* --- CSR Register --- */ /* Alias word address of LSION bit */ #define RCC_CSR_OFFSET (RCC_OFFSET + 0x74U) #define RCC_LSION_BIT_NUMBER 0x00U #define RCC_CSR_LSION_BB (PERIPH_BB_BASE + (RCC_CSR_OFFSET * 32U) + (RCC_LSION_BIT_NUMBER * 4U)) /* CR register byte 3 (Bits[23:16]) base address */ #define RCC_CR_BYTE2_ADDRESS 0x40023802U /* CIR register byte 2 (Bits[15:8]) base address */ #define RCC_CIR_BYTE1_ADDRESS ((uint32_t)(RCC_BASE + 0x0CU + 0x01U)) /* CIR register byte 3 (Bits[23:16]) base address */ #define RCC_CIR_BYTE2_ADDRESS ((uint32_t)(RCC_BASE + 0x0CU + 0x02U)) /* BDCR register base address */ #define RCC_BDCR_BYTE0_ADDRESS (PERIPH_BASE + RCC_BDCR_OFFSET) #define RCC_DBP_TIMEOUT_VALUE 2U #define RCC_LSE_TIMEOUT_VALUE LSE_STARTUP_TIMEOUT #define HSE_TIMEOUT_VALUE HSE_STARTUP_TIMEOUT #define HSI_TIMEOUT_VALUE 2U /* 2 ms */ #define LSI_TIMEOUT_VALUE 2U /* 2 ms */ #define CLOCKSWITCH_TIMEOUT_VALUE 5000U /* 5 s */ /** * @} */ /** * @} */ /* Private macros ------------------------------------------------------------*/ /** @defgroup RCC_Private_Macros RCC Private Macros * @{ */ /** @defgroup RCC_IS_RCC_Definitions RCC Private macros to check input parameters * @{ */ #define IS_RCC_OSCILLATORTYPE(OSCILLATOR) ((OSCILLATOR) <= 15U) #define IS_RCC_HSE(HSE) (((HSE) == RCC_HSE_OFF) || ((HSE) == RCC_HSE_ON) || \ ((HSE) == RCC_HSE_BYPASS)) #define IS_RCC_LSE(LSE) (((LSE) == RCC_LSE_OFF) || ((LSE) == RCC_LSE_ON) || \ ((LSE) == RCC_LSE_BYPASS)) #define IS_RCC_HSI(HSI) (((HSI) == RCC_HSI_OFF) || ((HSI) == RCC_HSI_ON)) #define IS_RCC_LSI(LSI) (((LSI) == RCC_LSI_OFF) || ((LSI) == RCC_LSI_ON)) #define IS_RCC_PLL(PLL) (((PLL) == RCC_PLL_NONE) ||((PLL) == RCC_PLL_OFF) || ((PLL) == RCC_PLL_ON)) #define IS_RCC_PLLSOURCE(SOURCE) (((SOURCE) == RCC_PLLSOURCE_HSI) || \ ((SOURCE) == RCC_PLLSOURCE_HSE)) #define IS_RCC_SYSCLKSOURCE(SOURCE) (((SOURCE) == RCC_SYSCLKSOURCE_HSI) || \ ((SOURCE) == RCC_SYSCLKSOURCE_HSE) || \ ((SOURCE) == RCC_SYSCLKSOURCE_PLLCLK) || \ ((SOURCE) == RCC_SYSCLKSOURCE_PLLRCLK)) #define IS_RCC_RTCCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_RTCCLKSOURCE_LSE) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_LSI) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV2) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV3) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV4) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV5) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV6) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV7) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV8) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV9) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV10) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV11) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV12) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV13) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV14) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV15) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV16) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV17) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV18) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV19) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV20) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV21) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV22) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV23) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV24) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV25) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV26) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV27) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV28) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV29) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV30) || \ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV31)) #define IS_RCC_PLLM_VALUE(VALUE) ((VALUE) <= 63U) #define IS_RCC_PLLP_VALUE(VALUE) (((VALUE) == 2U) || ((VALUE) == 4U) || ((VALUE) == 6U) || ((VALUE) == 8U)) #define IS_RCC_PLLQ_VALUE(VALUE) ((2U <= (VALUE)) && ((VALUE) <= 15U)) #define IS_RCC_HCLK(HCLK) (((HCLK) == RCC_SYSCLK_DIV1) || ((HCLK) == RCC_SYSCLK_DIV2) || \ ((HCLK) == RCC_SYSCLK_DIV4) || ((HCLK) == RCC_SYSCLK_DIV8) || \ ((HCLK) == RCC_SYSCLK_DIV16) || ((HCLK) == RCC_SYSCLK_DIV64) || \ ((HCLK) == RCC_SYSCLK_DIV128) || ((HCLK) == RCC_SYSCLK_DIV256) || \ ((HCLK) == RCC_SYSCLK_DIV512)) #define IS_RCC_CLOCKTYPE(CLK) ((1U <= (CLK)) && ((CLK) <= 15U)) #define IS_RCC_PCLK(PCLK) (((PCLK) == RCC_HCLK_DIV1) || ((PCLK) == RCC_HCLK_DIV2) || \ ((PCLK) == RCC_HCLK_DIV4) || ((PCLK) == RCC_HCLK_DIV8) || \ ((PCLK) == RCC_HCLK_DIV16)) #define IS_RCC_MCO(MCOx) (((MCOx) == RCC_MCO1) || ((MCOx) == RCC_MCO2)) #define IS_RCC_MCO1SOURCE(SOURCE) (((SOURCE) == RCC_MCO1SOURCE_HSI) || ((SOURCE) == RCC_MCO1SOURCE_LSE) || \ ((SOURCE) == RCC_MCO1SOURCE_HSE) || ((SOURCE) == RCC_MCO1SOURCE_PLLCLK)) #define IS_RCC_MCODIV(DIV) (((DIV) == RCC_MCODIV_1) || ((DIV) == RCC_MCODIV_2) || \ ((DIV) == RCC_MCODIV_3) || ((DIV) == RCC_MCODIV_4) || \ ((DIV) == RCC_MCODIV_5)) #define IS_RCC_CALIBRATION_VALUE(VALUE) ((VALUE) <= 0x1FU) /** * @} */ /** * @} */ /** * @} */ /** * @} */ #ifdef __cplusplus } #endif #endif /* __STM32F4xx_HAL_RCC_H */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/