Adjustments for flipped display view:
After some testing the t3_profile implementation in flipped mode some changes in the visualization were necessary to get a correct view.
line source
/**+ −
******************************************************************************+ −
* @file stm32f4xx_hal.c+ −
* @author MCD Application Team+ −
* @brief HAL module driver.+ −
* This is the common part of the HAL initialization+ −
*+ −
@verbatim+ −
==============================================================================+ −
##### How to use this driver #####+ −
==============================================================================+ −
[..]+ −
The common HAL driver contains a set of generic and common APIs that can be+ −
used by the PPP peripheral drivers and the user to start using the HAL. + −
[..]+ −
The HAL contains two APIs' categories: + −
(+) Common HAL APIs+ −
(+) Services HAL APIs+ −
+ −
@endverbatim+ −
******************************************************************************+ −
* @attention+ −
*+ −
* <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2>+ −
*+ −
* Redistribution and use in source and binary forms, with or without modification,+ −
* are permitted provided that the following conditions are met:+ −
* 1. Redistributions of source code must retain the above copyright notice,+ −
* this list of conditions and the following disclaimer.+ −
* 2. Redistributions in binary form must reproduce the above copyright notice,+ −
* this list of conditions and the following disclaimer in the documentation+ −
* and/or other materials provided with the distribution.+ −
* 3. Neither the name of STMicroelectronics nor the names of its contributors+ −
* may be used to endorse or promote products derived from this software+ −
* without specific prior written permission.+ −
*+ −
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"+ −
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE+ −
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE+ −
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE+ −
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL+ −
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR+ −
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER+ −
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,+ −
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE+ −
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.+ −
*+ −
******************************************************************************+ −
*/ + −
+ −
/* Includes ------------------------------------------------------------------*/+ −
#include "stm32f4xx_hal.h"+ −
+ −
/** @addtogroup STM32F4xx_HAL_Driver+ −
* @{+ −
*/+ −
+ −
/** @defgroup HAL HAL+ −
* @brief HAL module driver.+ −
* @{+ −
*/+ −
+ −
/* Private typedef -----------------------------------------------------------*/+ −
/* Private define ------------------------------------------------------------*/+ −
/** @addtogroup HAL_Private_Constants+ −
* @{+ −
*/+ −
/**+ −
* @brief STM32F4xx HAL Driver version number V1.7.4+ −
*/+ −
#define __STM32F4xx_HAL_VERSION_MAIN (0x01U) /*!< [31:24] main version */+ −
#define __STM32F4xx_HAL_VERSION_SUB1 (0x07U) /*!< [23:16] sub1 version */+ −
#define __STM32F4xx_HAL_VERSION_SUB2 (0x04U) /*!< [15:8] sub2 version */+ −
#define __STM32F4xx_HAL_VERSION_RC (0x00U) /*!< [7:0] release candidate */ + −
#define __STM32F4xx_HAL_VERSION ((__STM32F4xx_HAL_VERSION_MAIN << 24U)\+ −
|(__STM32F4xx_HAL_VERSION_SUB1 << 16U)\+ −
|(__STM32F4xx_HAL_VERSION_SUB2 << 8U )\+ −
|(__STM32F4xx_HAL_VERSION_RC))+ −
+ −
#define IDCODE_DEVID_MASK 0x00000FFFU+ −
+ −
/* ------------ RCC registers bit address in the alias region ----------- */+ −
#define SYSCFG_OFFSET (SYSCFG_BASE - PERIPH_BASE)+ −
/* --- MEMRMP Register ---*/ + −
/* Alias word address of UFB_MODE bit */ + −
#define MEMRMP_OFFSET SYSCFG_OFFSET + −
#define UFB_MODE_BIT_NUMBER SYSCFG_MEMRMP_UFB_MODE_Pos+ −
#define UFB_MODE_BB (uint32_t)(PERIPH_BB_BASE + (MEMRMP_OFFSET * 32U) + (UFB_MODE_BIT_NUMBER * 4U)) + −
+ −
/* --- CMPCR Register ---*/ + −
/* Alias word address of CMP_PD bit */ + −
#define CMPCR_OFFSET (SYSCFG_OFFSET + 0x20U) + −
#define CMP_PD_BIT_NUMBER SYSCFG_CMPCR_CMP_PD_Pos+ −
#define CMPCR_CMP_PD_BB (uint32_t)(PERIPH_BB_BASE + (CMPCR_OFFSET * 32U) + (CMP_PD_BIT_NUMBER * 4U))+ −
+ −
/* --- MCHDLYCR Register ---*/ + −
/* Alias word address of BSCKSEL bit */ + −
#define MCHDLYCR_OFFSET (SYSCFG_OFFSET + 0x30U) + −
#define BSCKSEL_BIT_NUMBER SYSCFG_MCHDLYCR_BSCKSEL_Pos+ −
#define MCHDLYCR_BSCKSEL_BB (uint32_t)(PERIPH_BB_BASE + (MCHDLYCR_OFFSET * 32U) + (BSCKSEL_BIT_NUMBER * 4U))+ −
/**+ −
* @}+ −
*/+ −
+ −
/* Private macro -------------------------------------------------------------*/+ −
/* Private variables ---------------------------------------------------------*/+ −
/** @addtogroup HAL_Private_Variables+ −
* @{+ −
*/+ −
__IO uint32_t uwTick;+ −
uint32_t uwTickPrio = (1UL << __NVIC_PRIO_BITS); /* Invalid PRIO */+ −
HAL_TickFreqTypeDef uwTickFreq = HAL_TICK_FREQ_DEFAULT; /* 1KHz */+ −
/**+ −
* @}+ −
*/+ −
/* Private function prototypes -----------------------------------------------*/+ −
/* Private functions ---------------------------------------------------------*/+ −
+ −
/** @defgroup HAL_Exported_Functions HAL Exported Functions+ −
* @{+ −
*/+ −
+ −
/** @defgroup HAL_Exported_Functions_Group1 Initialization and de-initialization Functions + −
* @brief Initialization and de-initialization functions+ −
*+ −
@verbatim + −
===============================================================================+ −
##### Initialization and Configuration functions #####+ −
===============================================================================+ −
[..] This section provides functions allowing to:+ −
(+) Initializes the Flash interface the NVIC allocation and initial clock + −
configuration. It initializes the systick also when timeout is needed + −
and the backup domain when enabled.+ −
(+) De-Initializes common part of the HAL.+ −
(+) Configure the time base source to have 1ms time base with a dedicated + −
Tick interrupt priority. + −
(++) SysTick timer is used by default as source of time base, but user+ −
can eventually implement his proper time base source (a general purpose + −
timer for example or other time source), keeping in mind that Time base + −
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and + −
handled in milliseconds basis.+ −
(++) Time base configuration function (HAL_InitTick ()) is called automatically + −
at the beginning of the program after reset by HAL_Init() or at any time + −
when clock is configured, by HAL_RCC_ClockConfig(). + −
(++) Source of time base is configured to generate interrupts at regular + −
time intervals. Care must be taken if HAL_Delay() is called from a + −
peripheral ISR process, the Tick interrupt line must have higher priority + −
(numerically lower) than the peripheral interrupt. Otherwise the caller + −
ISR process will be blocked. + −
(++) functions affecting time base configurations are declared as __weak + −
to make override possible in case of other implementations in user file.+ −
@endverbatim+ −
* @{+ −
*/+ −
+ −
/**+ −
* @brief This function is used to initialize the HAL Library; it must be the first + −
* instruction to be executed in the main program (before to call any other+ −
* HAL function), it performs the following:+ −
* Configure the Flash prefetch, instruction and Data caches.+ −
* Configures the SysTick to generate an interrupt each 1 millisecond,+ −
* which is clocked by the HSI (at this stage, the clock is not yet+ −
* configured and thus the system is running from the internal HSI at 16 MHz).+ −
* Set NVIC Group Priority to 4.+ −
* Calls the HAL_MspInit() callback function defined in user file + −
* "stm32f4xx_hal_msp.c" to do the global low level hardware initialization + −
* + −
* @note SysTick is used as time base for the HAL_Delay() function, the application+ −
* need to ensure that the SysTick time base is always set to 1 millisecond+ −
* to have correct HAL operation.+ −
* @retval HAL status+ −
*/+ −
HAL_StatusTypeDef HAL_Init(void)+ −
{+ −
/* Configure Flash prefetch, Instruction cache, Data cache */ + −
#if (INSTRUCTION_CACHE_ENABLE != 0U)+ −
__HAL_FLASH_INSTRUCTION_CACHE_ENABLE();+ −
#endif /* INSTRUCTION_CACHE_ENABLE */+ −
+ −
#if (DATA_CACHE_ENABLE != 0U)+ −
__HAL_FLASH_DATA_CACHE_ENABLE();+ −
#endif /* DATA_CACHE_ENABLE */+ −
+ −
#if (PREFETCH_ENABLE != 0U)+ −
__HAL_FLASH_PREFETCH_BUFFER_ENABLE();+ −
#endif /* PREFETCH_ENABLE */+ −
+ −
/* Set Interrupt Group Priority */+ −
HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_4);+ −
+ −
/* Use systick as time base source and configure 1ms tick (default clock after Reset is HSI) */+ −
HAL_InitTick(TICK_INT_PRIORITY);+ −
+ −
/* Init the low level hardware */+ −
HAL_MspInit();+ −
+ −
/* Return function status */+ −
return HAL_OK;+ −
}+ −
+ −
/**+ −
* @brief This function de-Initializes common part of the HAL and stops the systick.+ −
* This function is optional. + −
* @retval HAL status+ −
*/+ −
HAL_StatusTypeDef HAL_DeInit(void)+ −
{+ −
/* Reset of all peripherals */+ −
__HAL_RCC_APB1_FORCE_RESET();+ −
__HAL_RCC_APB1_RELEASE_RESET();+ −
+ −
__HAL_RCC_APB2_FORCE_RESET();+ −
__HAL_RCC_APB2_RELEASE_RESET();+ −
+ −
__HAL_RCC_AHB1_FORCE_RESET();+ −
__HAL_RCC_AHB1_RELEASE_RESET();+ −
+ −
__HAL_RCC_AHB2_FORCE_RESET();+ −
__HAL_RCC_AHB2_RELEASE_RESET();+ −
+ −
__HAL_RCC_AHB3_FORCE_RESET();+ −
__HAL_RCC_AHB3_RELEASE_RESET();+ −
+ −
/* De-Init the low level hardware */+ −
HAL_MspDeInit();+ −
+ −
/* Return function status */+ −
return HAL_OK;+ −
}+ −
+ −
/**+ −
* @brief Initialize the MSP.+ −
* @retval None+ −
*/+ −
__weak void HAL_MspInit(void)+ −
{+ −
/* NOTE : This function should not be modified, when the callback is needed,+ −
the HAL_MspInit could be implemented in the user file+ −
*/+ −
}+ −
+ −
/**+ −
* @brief DeInitializes the MSP.+ −
* @retval None+ −
*/+ −
__weak void HAL_MspDeInit(void)+ −
{+ −
/* NOTE : This function should not be modified, when the callback is needed,+ −
the HAL_MspDeInit could be implemented in the user file+ −
*/ + −
}+ −
+ −
/**+ −
* @brief This function configures the source of the time base.+ −
* The time source is configured to have 1ms time base with a dedicated + −
* Tick interrupt priority.+ −
* @note This function is called automatically at the beginning of program after+ −
* reset by HAL_Init() or at any time when clock is reconfigured by HAL_RCC_ClockConfig().+ −
* @note In the default implementation, SysTick timer is the source of time base. + −
* It is used to generate interrupts at regular time intervals. + −
* Care must be taken if HAL_Delay() is called from a peripheral ISR process, + −
* The SysTick interrupt must have higher priority (numerically lower)+ −
* than the peripheral interrupt. Otherwise the caller ISR process will be blocked.+ −
* The function is declared as __weak to be overwritten in case of other+ −
* implementation in user file.+ −
* @param TickPriority Tick interrupt priority.+ −
* @retval HAL status+ −
*/+ −
__weak HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority)+ −
{+ −
/* Configure the SysTick to have interrupt in 1ms time basis*/+ −
if (HAL_SYSTICK_Config(SystemCoreClock / (1000U / uwTickFreq)) > 0U)+ −
{+ −
return HAL_ERROR;+ −
}+ −
+ −
/* Configure the SysTick IRQ priority */+ −
if (TickPriority < (1UL << __NVIC_PRIO_BITS))+ −
{+ −
HAL_NVIC_SetPriority(SysTick_IRQn, TickPriority, 0U);+ −
uwTickPrio = TickPriority;+ −
}+ −
else+ −
{+ −
return HAL_ERROR;+ −
}+ −
+ −
/* Return function status */+ −
return HAL_OK;+ −
}+ −
+ −
/**+ −
* @}+ −
*/+ −
+ −
/** @defgroup HAL_Exported_Functions_Group2 HAL Control functions + −
* @brief HAL Control functions+ −
*+ −
@verbatim+ −
===============================================================================+ −
##### HAL Control functions #####+ −
===============================================================================+ −
[..] This section provides functions allowing to:+ −
(+) Provide a tick value in millisecond+ −
(+) Provide a blocking delay in millisecond+ −
(+) Suspend the time base source interrupt+ −
(+) Resume the time base source interrupt+ −
(+) Get the HAL API driver version+ −
(+) Get the device identifier+ −
(+) Get the device revision identifier+ −
(+) Enable/Disable Debug module during SLEEP mode+ −
(+) Enable/Disable Debug module during STOP mode+ −
(+) Enable/Disable Debug module during STANDBY mode+ −
+ −
@endverbatim+ −
* @{+ −
*/+ −
+ −
/**+ −
* @brief This function is called to increment a global variable "uwTick"+ −
* used as application time base.+ −
* @note In the default implementation, this variable is incremented each 1ms+ −
* in SysTick ISR.+ −
* @note This function is declared as __weak to be overwritten in case of other + −
* implementations in user file.+ −
* @retval None+ −
*/+ −
__weak void HAL_IncTick(void)+ −
{+ −
uwTick += uwTickFreq;+ −
}+ −
+ −
/**+ −
* @brief Provides a tick value in millisecond.+ −
* @note This function is declared as __weak to be overwritten in case of other + −
* implementations in user file.+ −
* @retval tick value+ −
*/+ −
__weak uint32_t HAL_GetTick(void)+ −
{+ −
return uwTick;+ −
}+ −
+ −
/**+ −
* @brief This function returns a tick priority.+ −
* @retval tick priority+ −
*/+ −
uint32_t HAL_GetTickPrio(void)+ −
{+ −
return uwTickPrio;+ −
}+ −
+ −
/**+ −
* @brief Set new tick Freq.+ −
* @retval Status+ −
*/+ −
HAL_StatusTypeDef HAL_SetTickFreq(HAL_TickFreqTypeDef Freq)+ −
{+ −
HAL_StatusTypeDef status = HAL_OK;+ −
assert_param(IS_TICKFREQ(Freq));+ −
+ −
if (uwTickFreq != Freq)+ −
{+ −
uwTickFreq = Freq;+ −
+ −
/* Apply the new tick Freq */+ −
status = HAL_InitTick(uwTickPrio);+ −
}+ −
+ −
return status;+ −
}+ −
+ −
/**+ −
* @brief Return tick frequency.+ −
* @retval tick period in Hz+ −
*/+ −
HAL_TickFreqTypeDef HAL_GetTickFreq(void)+ −
{+ −
return uwTickFreq;+ −
}+ −
+ −
/**+ −
* @brief This function provides minimum delay (in milliseconds) based + −
* on variable incremented.+ −
* @note In the default implementation , SysTick timer is the source of time base.+ −
* It is used to generate interrupts at regular time intervals where uwTick+ −
* is incremented.+ −
* @note This function is declared as __weak to be overwritten in case of other+ −
* implementations in user file.+ −
* @param Delay specifies the delay time length, in milliseconds.+ −
* @retval None+ −
*/+ −
__weak void HAL_Delay(uint32_t Delay)+ −
{+ −
uint32_t tickstart = HAL_GetTick();+ −
uint32_t wait = Delay;+ −
+ −
/* Add a freq to guarantee minimum wait */+ −
if (wait < HAL_MAX_DELAY)+ −
{+ −
wait += (uint32_t)(uwTickFreq);+ −
}+ −
+ −
while((HAL_GetTick() - tickstart) < wait)+ −
{+ −
}+ −
}+ −
+ −
/**+ −
* @brief Suspend Tick increment.+ −
* @note In the default implementation , SysTick timer is the source of time base. It is+ −
* used to generate interrupts at regular time intervals. Once HAL_SuspendTick()+ −
* is called, the SysTick interrupt will be disabled and so Tick increment + −
* is suspended.+ −
* @note This function is declared as __weak to be overwritten in case of other+ −
* implementations in user file.+ −
* @retval None+ −
*/+ −
__weak void HAL_SuspendTick(void)+ −
{+ −
/* Disable SysTick Interrupt */+ −
SysTick->CTRL &= ~SysTick_CTRL_TICKINT_Msk;+ −
}+ −
+ −
/**+ −
* @brief Resume Tick increment.+ −
* @note In the default implementation , SysTick timer is the source of time base. It is+ −
* used to generate interrupts at regular time intervals. Once HAL_ResumeTick()+ −
* is called, the SysTick interrupt will be enabled and so Tick increment + −
* is resumed.+ −
* @note This function is declared as __weak to be overwritten in case of other+ −
* implementations in user file.+ −
* @retval None+ −
*/+ −
__weak void HAL_ResumeTick(void)+ −
{+ −
/* Enable SysTick Interrupt */+ −
SysTick->CTRL |= SysTick_CTRL_TICKINT_Msk;+ −
}+ −
+ −
/**+ −
* @brief Returns the HAL revision+ −
* @retval version : 0xXYZR (8bits for each decimal, R for RC)+ −
*/+ −
uint32_t HAL_GetHalVersion(void)+ −
{+ −
return __STM32F4xx_HAL_VERSION;+ −
}+ −
+ −
/**+ −
* @brief Returns the device revision identifier.+ −
* @retval Device revision identifier+ −
*/+ −
uint32_t HAL_GetREVID(void)+ −
{+ −
return((DBGMCU->IDCODE) >> 16U);+ −
}+ −
+ −
/**+ −
* @brief Returns the device identifier.+ −
* @retval Device identifier+ −
*/+ −
uint32_t HAL_GetDEVID(void)+ −
{+ −
return((DBGMCU->IDCODE) & IDCODE_DEVID_MASK);+ −
}+ −
+ −
/**+ −
* @brief Enable the Debug Module during SLEEP mode+ −
* @retval None+ −
*/+ −
void HAL_DBGMCU_EnableDBGSleepMode(void)+ −
{+ −
SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_SLEEP);+ −
}+ −
+ −
/**+ −
* @brief Disable the Debug Module during SLEEP mode+ −
* @retval None+ −
*/+ −
void HAL_DBGMCU_DisableDBGSleepMode(void)+ −
{+ −
CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_SLEEP);+ −
}+ −
+ −
/**+ −
* @brief Enable the Debug Module during STOP mode+ −
* @retval None+ −
*/+ −
void HAL_DBGMCU_EnableDBGStopMode(void)+ −
{+ −
SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STOP);+ −
}+ −
+ −
/**+ −
* @brief Disable the Debug Module during STOP mode+ −
* @retval None+ −
*/+ −
void HAL_DBGMCU_DisableDBGStopMode(void)+ −
{+ −
CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STOP);+ −
}+ −
+ −
/**+ −
* @brief Enable the Debug Module during STANDBY mode+ −
* @retval None+ −
*/+ −
void HAL_DBGMCU_EnableDBGStandbyMode(void)+ −
{+ −
SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STANDBY);+ −
}+ −
+ −
/**+ −
* @brief Disable the Debug Module during STANDBY mode+ −
* @retval None+ −
*/+ −
void HAL_DBGMCU_DisableDBGStandbyMode(void)+ −
{+ −
CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_STANDBY);+ −
}+ −
+ −
/**+ −
* @brief Enables the I/O Compensation Cell.+ −
* @note The I/O compensation cell can be used only when the device supply+ −
* voltage ranges from 2.4 to 3.6 V. + −
* @retval None+ −
*/+ −
void HAL_EnableCompensationCell(void)+ −
{+ −
*(__IO uint32_t *)CMPCR_CMP_PD_BB = (uint32_t)ENABLE;+ −
}+ −
+ −
/**+ −
* @brief Power-down the I/O Compensation Cell.+ −
* @note The I/O compensation cell can be used only when the device supply+ −
* voltage ranges from 2.4 to 3.6 V. + −
* @retval None+ −
*/+ −
void HAL_DisableCompensationCell(void)+ −
{+ −
*(__IO uint32_t *)CMPCR_CMP_PD_BB = (uint32_t)DISABLE;+ −
}+ −
+ −
/**+ −
* @brief Return the unique device identifier (UID based on 96 bits)+ −
* @param UID pointer to 3 words array.+ −
* @retval Device identifier+ −
*/+ −
void HAL_GetUID(uint32_t *UID)+ −
{+ −
UID[0] = (uint32_t)(READ_REG(*((uint32_t *)UID_BASE)));+ −
UID[1] = (uint32_t)(READ_REG(*((uint32_t *)(UID_BASE + 4U))));+ −
UID[2] = (uint32_t)(READ_REG(*((uint32_t *)(UID_BASE + 8U))));+ −
}+ −
+ −
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) ||\+ −
defined(STM32F469xx) || defined(STM32F479xx)+ −
/**+ −
* @brief Enables the Internal FLASH Bank Swapping.+ −
* + −
* @note This function can be used only for STM32F42xxx/43xxx devices. + −
*+ −
* @note Flash Bank2 mapped at 0x08000000 (and aliased @0x00000000) + −
* and Flash Bank1 mapped at 0x08100000 (and aliased at 0x00100000) + −
*+ −
* @retval None+ −
*/+ −
void HAL_EnableMemorySwappingBank(void)+ −
{+ −
*(__IO uint32_t *)UFB_MODE_BB = (uint32_t)ENABLE;+ −
}+ −
+ −
/**+ −
* @brief Disables the Internal FLASH Bank Swapping.+ −
* + −
* @note This function can be used only for STM32F42xxx/43xxx devices. + −
*+ −
* @note The default state : Flash Bank1 mapped at 0x08000000 (and aliased @0x00000000) + −
* and Flash Bank2 mapped at 0x08100000 (and aliased at 0x00100000) + −
* + −
* @retval None+ −
*/+ −
void HAL_DisableMemorySwappingBank(void)+ −
{+ −
*(__IO uint32_t *)UFB_MODE_BB = (uint32_t)DISABLE;+ −
}+ −
#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */+ −
/**+ −
* @}+ −
*/+ −
+ −
/**+ −
* @}+ −
*/+ −
+ −
/**+ −
* @}+ −
*/+ −
+ −
/**+ −
* @}+ −
*/+ −
+ −
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/+ −