view Discovery/Src/ostc.c @ 250:822416168585 bm-2

Buelmann: new implementation for ceiling Since my first functional fix in the ceiling computation in commit ceecabfddb57, I noticed that the computation used a linear search, that became rather computational expensive after that commit. The simple question is: why not a binary search? So, this commit implements the binary search. But there is a long story attached to this. Comparing ceiling results from hwOS and this OSTC4 code were very different. Basically, the original OSTC4 algorithm computed the ceiling using the same GFlow to GFhigh slope, in such a way, that the ceiling was in sync with the presented deco stops, where the hwOS code presents a GFhigh based ceiling. This said, it is more logical when the OSTC4 and hwOS code give similar results. This new recursive algorithm gives very similar results for the ceiling compared to hwOS. To be complete here, the Buelmann ceiling is the depth to which you can ascend, so that the leading tissue reaches GFhigh. This also explains why the deepest deco stop is normally deeper than the ceiling (unless one dives with GF like 80/80). The code implemented here is rather straightforward recursion. Signed-off-by: Jan Mulder <jlmulder@xs4all.nl>
author Jan Mulder <jlmulder@xs4all.nl>
date Thu, 11 Apr 2019 17:48:48 +0200
parents f6c52eb0e25d
children 5ca177d2df5d
line wrap: on
line source

///////////////////////////////////////////////////////////////////////////////
/// -*- coding: UTF-8 -*-
///
/// \file   Discovery/Src/ostc.c
/// \brief  Hardware specific configuration
/// \author Heinrichs Weikamp gmbh
/// \date   05-Dec-2014
///
/// \details
///
/// $Id$
///////////////////////////////////////////////////////////////////////////////
/// \par Copyright (c) 2014-2018 Heinrichs Weikamp gmbh
///
///     This program is free software: you can redistribute it and/or modify
///     it under the terms of the GNU General Public License as published by
///     the Free Software Foundation, either version 3 of the License, or
///     (at your option) any later version.
///
///     This program is distributed in the hope that it will be useful,
///     but WITHOUT ANY WARRANTY; without even the implied warranty of
///     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
///     GNU General Public License for more details.
///
///     You should have received a copy of the GNU General Public License
///     along with this program.  If not, see <http://www.gnu.org/licenses/>.
//////////////////////////////////////////////////////////////////////////////

/* Includes ------------------------------------------------------------------*/
#include "ostc.h"
#include "stm32f4xx_hal.h"

#ifndef BOOTLOADER_STANDALONE
#include "tCCR.h"
#endif

/* Exported variables --------------------------------------------------------*/
SPI_HandleTypeDef hspiDisplay;
SPI_HandleTypeDef cpu2DmaSpi;


UART_HandleTypeDef UartHandle;
UART_HandleTypeDef UartPiezoTxHandle;
UART_HandleTypeDef UartIR_HUD_Handle;

__IO ITStatus UartReady = RESET;
__IO ITStatus UartReadyHUD = RESET;

/* Private types -------------------------------------------------------------*/

/* Private variables ---------------------------------------------------------*/

/* Private variables with external access via get_xxx() function -------------*/

/* Private function prototypes -----------------------------------------------*/

/* Exported functions --------------------------------------------------------*/

/** SPI init function
    * called from HAL
    */
void MX_SPI_Init(void)
{
    hspiDisplay.Instance = SPI5;
    hspiDisplay.Init.Mode = SPI_MODE_MASTER;
    hspiDisplay.Init.Direction = SPI_DIRECTION_2LINES;
    hspiDisplay.Init.DataSize = SPI_DATASIZE_8BIT;
    hspiDisplay.Init.CLKPolarity = SPI_POLARITY_LOW;
    hspiDisplay.Init.CLKPhase = SPI_PHASE_1EDGE;
    hspiDisplay.Init.NSS = SPI_NSS_SOFT;
    hspiDisplay.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_32;//SPI_BAUDRATEPRESCALER_4;//SPI_BAUDRATEPRESCALER_256;
    hspiDisplay.Init.FirstBit = SPI_FIRSTBIT_MSB;
    hspiDisplay.Init.TIMode = SPI_TIMODE_DISABLED;
    hspiDisplay.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLED;
    HAL_SPI_Init(&hspiDisplay);

    cpu2DmaSpi.Instance                 = SPI1;
    cpu2DmaSpi.Init.Mode                = SPI_MODE_MASTER;
    cpu2DmaSpi.Init.Direction           = SPI_DIRECTION_2LINES;
    cpu2DmaSpi.Init.DataSize            = SPI_DATASIZE_8BIT;
    cpu2DmaSpi.Init.CLKPolarity         = SPI_POLARITY_LOW;
    cpu2DmaSpi.Init.CLKPhase            = SPI_PHASE_1EDGE;
    cpu2DmaSpi.Init.NSS                 = SPI_NSS_SOFT;//SPI_NSS_HARD_OUTPUT;//SPI_NSS_SOFT;
    cpu2DmaSpi.Init.BaudRatePrescaler   = SPI_BAUDRATEPRESCALER_128; 
    cpu2DmaSpi.Init.FirstBit            = SPI_FIRSTBIT_MSB;
    cpu2DmaSpi.Init.TIMode              = SPI_TIMODE_DISABLED;
    cpu2DmaSpi.Init.CRCCalculation 		= SPI_CRCCALCULATION_DISABLED;
    cpu2DmaSpi.Init.CRCPolynomial 		= 7;

    HAL_SPI_Init(&cpu2DmaSpi);
}


void MX_GPIO_Backlight_max_static_only_Init(void)
{
    GPIO_InitTypeDef GPIO_InitStruct;
    TIM_BACKLIGHT_GPIO_ENABLE();

    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;//GPIO_PULLUP; /* should be normally high */
    GPIO_InitStruct.Speed = GPIO_SPEED_LOW;

    GPIO_InitStruct.Pin = TIM_BACKLIGHT_PIN;
    HAL_GPIO_Init(TIM_BACKLIGHT_GPIO_PORT, &GPIO_InitStruct);

    HAL_GPIO_WritePin(TIM_BACKLIGHT_GPIO_PORT,TIM_BACKLIGHT_PIN,GPIO_PIN_SET);
}


void MX_GPIO_One_Button_only_Init(void)
{
    GPIO_InitTypeDef GPIO_InitStruct;
    BUTTON_NEXT_GPIO_ENABLE();

    GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
    GPIO_InitStruct.Pull = GPIO_NOPULL;//GPIO_PULLUP; /* should be normally high */
    GPIO_InitStruct.Speed = GPIO_SPEED_LOW;

    GPIO_InitStruct.Pin = BUTTON_NEXT_PIN;
    HAL_GPIO_Init(BUTTON_NEXT_GPIO_PORT, &GPIO_InitStruct);
}


GPIO_PinState MX_GPIO_Read_The_One_Button(void)
{
    return HAL_GPIO_ReadPin(BUTTON_NEXT_GPIO_PORT, BUTTON_NEXT_PIN);
}

void MX_GPIO_Init(void)
{
    GPIO_InitTypeDef GPIO_InitStruct;

    DISPLAY_CSB_GPIO_ENABLE();
    DISPLAY_RESETB_GPIO_ENABLE();
    EXTFLASH_CSB_GPIO_ENABLE();
    SMALLCPU_CSB_GPIO_ENABLE();
    OSCILLOSCOPE_GPIO_ENABLE();
    OSCILLOSCOPE2_GPIO_ENABLE();

    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_PULLUP;
    GPIO_InitStruct.Speed = GPIO_SPEED_LOW;

    GPIO_InitStruct.Pin = DISPLAY_CSB_PIN;
    HAL_GPIO_Init(DISPLAY_CSB_GPIO_PORT, &GPIO_InitStruct);

    GPIO_InitStruct.Pin = DISPLAY_RESETB_PIN;
    HAL_GPIO_Init(DISPLAY_RESETB_GPIO_PORT, &GPIO_InitStruct);

    GPIO_InitStruct.Pin = EXTFLASH_CSB_PIN;
    HAL_GPIO_Init(EXTFLASH_CSB_GPIO_PORT, &GPIO_InitStruct);

    GPIO_InitStruct.Pin = OSCILLOSCOPE_PIN;
    HAL_GPIO_Init(OSCILLOSCOPE_GPIO_PORT, &GPIO_InitStruct);

    GPIO_InitStruct.Pin = OSCILLOSCOPE2_PIN;
    HAL_GPIO_Init(OSCILLOSCOPE2_GPIO_PORT, &GPIO_InitStruct);

#ifdef DISPLAY_BACKLIGHT_PIN
    DISPLAY_BACKLIGHT_GPIO_ENABLE();
    GPIO_InitStruct.Pin = DISPLAY_BACKLIGHT_PIN;
    HAL_GPIO_Init(DISPLAY_BACKLIGHT_GPIO_PORT, &GPIO_InitStruct);
    HAL_GPIO_WritePin(DISPLAY_BACKLIGHT_GPIO_PORT,DISPLAY_BACKLIGHT_PIN,GPIO_PIN_SET);
#endif

#ifdef SMALLCPU_CSB_PIN
    SMALLCPU_CSB_GPIO_ENABLE();
    GPIO_InitStruct.Pin = SMALLCPU_CSB_PIN;
    HAL_GPIO_Init(SMALLCPU_CSB_GPIO_PORT, &GPIO_InitStruct);
    HAL_GPIO_WritePin(SMALLCPU_CSB_GPIO_PORT,SMALLCPU_CSB_PIN,GPIO_PIN_SET);
#endif

#ifdef SMALLCPU_BOOT0_PIN
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    SMALLCPU_BOOT0_GPIO_ENABLE();
    GPIO_InitStruct.Pin = SMALLCPU_BOOT0_PIN;
    HAL_GPIO_Init(SMALLCPU_BOOT0_GPIO_PORT, &GPIO_InitStruct);
    HAL_GPIO_WritePin(SMALLCPU_BOOT0_GPIO_PORT,SMALLCPU_BOOT0_PIN,GPIO_PIN_RESET);
    GPIO_InitStruct.Pull = GPIO_PULLUP;
#endif

#ifdef IR_HUD_ENABLE_PIN
    IR_HUD_ENABLE_GPIO_ENABLE();
    GPIO_InitStruct.Pin = IR_HUD_ENABLE_PIN;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    HAL_GPIO_Init(IR_HUD_ENABLE_GPIO_PORT, &GPIO_InitStruct);
    HAL_GPIO_WritePin(IR_HUD_ENABLE_GPIO_PORT,IR_HUD_ENABLE_PIN,GPIO_PIN_SET);
    GPIO_InitStruct.Pull = GPIO_PULLUP;
#endif

#ifdef BLE_NENABLE_PIN
    BLE_NENABLE_GPIO_ENABLE();
    MX_Bluetooth_PowerOff();
#endif

#ifdef TESTPIN
    GPIO_InitStruct.Pull = GPIO_PULLUP;
    TEST_GPIO_ENABLE();
    GPIO_InitStruct.Pin = TEST_PIN;
    HAL_GPIO_Init(TEST_GPIO_PORT, &GPIO_InitStruct);
    HAL_GPIO_WritePin(TEST_GPIO_PORT,TEST_PIN,GPIO_PIN_SET);
    GPIO_InitStruct.Pull = GPIO_PULLUP;
#endif
}


void MX_TestPin_High(void)
{
#ifdef TESTPIN
    HAL_GPIO_WritePin(TEST_GPIO_PORT,TEST_PIN,GPIO_PIN_SET);
#endif
}


void MX_TestPin_Low(void)
{
#ifdef TESTPIN
    HAL_GPIO_WritePin(TEST_GPIO_PORT,TEST_PIN,GPIO_PIN_RESET);
#endif
}

void MX_Bluetooth_PowerOn(void)
{
    GPIO_InitTypeDef GPIO_InitStruct;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
    GPIO_InitStruct.Pin = BLE_NENABLE_PIN;
    HAL_GPIO_Init(BLE_NENABLE_GPIO_PORT, &GPIO_InitStruct);
    HAL_GPIO_WritePin(BLE_NENABLE_GPIO_PORT,BLE_NENABLE_PIN,GPIO_PIN_RESET);
}


void MX_Bluetooth_PowerOff(void)
{
    GPIO_InitTypeDef GPIO_InitStruct;
    GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
    GPIO_InitStruct.Pin = BLE_NENABLE_PIN;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    HAL_GPIO_Init(BLE_NENABLE_GPIO_PORT, &GPIO_InitStruct);
}


void MX_SmallCPU_Reset_To_Boot(void)
{
#ifdef SMALLCPU_NRESET_PIN
    GPIO_InitTypeDef GPIO_InitStruct;

    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_LOW;

    SMALLCPU_NRESET_GPIO_ENABLE();
    GPIO_InitStruct.Pin = SMALLCPU_NRESET_PIN;
    HAL_GPIO_Init(SMALLCPU_NRESET_GPIO_PORT, &GPIO_InitStruct);
    HAL_GPIO_WritePin(SMALLCPU_NRESET_GPIO_PORT,SMALLCPU_NRESET_PIN,GPIO_PIN_RESET);
    HAL_GPIO_WritePin(SMALLCPU_BOOT0_GPIO_PORT,SMALLCPU_BOOT0_PIN,GPIO_PIN_SET);
    HAL_Delay(2);
    GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
    HAL_GPIO_Init(SMALLCPU_NRESET_GPIO_PORT, &GPIO_InitStruct);
    HAL_Delay(100);
    HAL_GPIO_WritePin(SMALLCPU_BOOT0_GPIO_PORT,SMALLCPU_BOOT0_PIN,GPIO_PIN_RESET);
#endif
}


void MX_SmallCPU_NO_Reset_Helper(void)
{
#ifdef SMALLCPU_NRESET_PIN
    GPIO_InitTypeDef GPIO_InitStruct;

    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_LOW;

    SMALLCPU_NRESET_GPIO_ENABLE();
    HAL_GPIO_Init(SMALLCPU_NRESET_GPIO_PORT, &GPIO_InitStruct);
    HAL_GPIO_WritePin(SMALLCPU_NRESET_GPIO_PORT,SMALLCPU_NRESET_PIN,GPIO_PIN_SET);
//	HAL_Delay(100);
//  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
//  HAL_GPIO_Init(SMALLCPU_NRESET_GPIO_PORT, &GPIO_InitStruct);
#endif
}


void MX_SmallCPU_Reset_To_Standard(void)
{
#ifdef SMALLCPU_NRESET_PIN
    GPIO_InitTypeDef GPIO_InitStruct;

    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_LOW;

    SMALLCPU_NRESET_GPIO_ENABLE();
    GPIO_InitStruct.Pin = SMALLCPU_NRESET_PIN;
    HAL_GPIO_Init(SMALLCPU_NRESET_GPIO_PORT, &GPIO_InitStruct);
    HAL_GPIO_WritePin(SMALLCPU_NRESET_GPIO_PORT,SMALLCPU_NRESET_PIN,GPIO_PIN_RESET);
    HAL_GPIO_WritePin(SMALLCPU_BOOT0_GPIO_PORT,SMALLCPU_BOOT0_PIN,GPIO_PIN_RESET);
    HAL_Delay(2);
    GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
    HAL_GPIO_Init(SMALLCPU_NRESET_GPIO_PORT, &GPIO_InitStruct);
#endif
}


uint8_t MX_UART_ButtonAdjust(uint8_t *array)
{
#ifdef USART_PIEZO
    uint8_t answer[4];
    HAL_UART_Transmit(&UartPiezoTxHandle,array,4,1000);
    HAL_UART_Receive(&UartPiezoTxHandle,answer,4,2000);
    if(	(answer[0] == array[0])
        &&(answer[1] == array[1])
        &&(answer[2] == array[2])
        &&(answer[3] == array[3]))
    return 1;
#endif
    return 0;
}


void MX_UART_Init(void)
{
  /*##-1- Configure the UART peripheral ######################################*/
  /* Put the USART peripheral in the Asynchronous mode (UART Mode) */
  /* UART1 configured as follow:
      - Word Length = 8 Bits
      - Stop Bit = One Stop bit
      - Parity = None
      - BaudRate = 9600 baud
      - Hardware flow control disabled (RTS and CTS signals) */

#ifdef USARTx_CTS_PIN
    UartHandle.Init.HwFlowCtl  = UART_HWCONTROL_RTS_CTS;
#else
    UartHandle.Init.HwFlowCtl  = UART_HWCONTROL_NONE;
#endif
    UartHandle.Instance        = USARTx;
    UartHandle.Init.BaudRate   = 115200;
    UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
    UartHandle.Init.StopBits   = UART_STOPBITS_1;
    UartHandle.Init.Parity     = UART_PARITY_NONE;
    UartHandle.Init.Mode       = UART_MODE_TX_RX;
    HAL_UART_Init(&UartHandle);

#ifdef USART_PIEZO
    UartPiezoTxHandle.Instance        = USART_PIEZO;
    UartPiezoTxHandle.Init.BaudRate   = 1200;
    UartPiezoTxHandle.Init.WordLength = UART_WORDLENGTH_8B;
    UartPiezoTxHandle.Init.StopBits   = UART_STOPBITS_1;
    UartPiezoTxHandle.Init.Parity     = UART_PARITY_NONE;
    UartPiezoTxHandle.Init.HwFlowCtl  = UART_HWCONTROL_NONE;
    UartPiezoTxHandle.Init.Mode       = UART_MODE_TX_RX;

    HAL_UART_Init(&UartPiezoTxHandle);
#endif

#ifdef USART_IR_HUD
    UartIR_HUD_Handle.Instance        = USART_IR_HUD;
    UartIR_HUD_Handle.Init.BaudRate   = 2400;
    UartIR_HUD_Handle.Init.WordLength = UART_WORDLENGTH_8B;
    UartIR_HUD_Handle.Init.StopBits   = UART_STOPBITS_1;
    UartIR_HUD_Handle.Init.Parity     = UART_PARITY_NONE;
    UartIR_HUD_Handle.Init.HwFlowCtl  = UART_HWCONTROL_NONE;
    UartIR_HUD_Handle.Init.Mode       = UART_MODE_TX_RX;

    HAL_UART_Init(&UartIR_HUD_Handle);
#endif
}

void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart)
{
    if(huart == &UartHandle)
        UartReady = SET;
}



//void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart)
void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart)
{
    if(huart == &UartHandle)
        UartReady = SET;
    else
    if(huart == &UartIR_HUD_Handle)
    {
        UartReadyHUD = SET;
    }
}

void MX_tell_reset_logik_alles_ok(void)
{
#ifdef RESET_LOGIC_ALLES_OK_PIN
    GPIO_InitTypeDef GPIO_InitStruct;

    RESET_LOGIC_ALLES_OK_GPIO_ENABLE();

    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
    GPIO_InitStruct.Pin = RESET_LOGIC_ALLES_OK_PIN;
    HAL_GPIO_Init(RESET_LOGIC_ALLES_OK_GPIO_PORT, &GPIO_InitStruct);

    HAL_GPIO_WritePin(RESET_LOGIC_ALLES_OK_GPIO_PORT,RESET_LOGIC_ALLES_OK_PIN,GPIO_PIN_RESET);
    HAL_Delay(1);
    HAL_GPIO_WritePin(RESET_LOGIC_ALLES_OK_GPIO_PORT,RESET_LOGIC_ALLES_OK_PIN,GPIO_PIN_SET);

    GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
    HAL_GPIO_Init(RESET_LOGIC_ALLES_OK_GPIO_PORT, &GPIO_InitStruct);
#endif
}


#ifndef BOOTLOADER_STANDALONE
void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart)
{
    if(huart == &UartIR_HUD_Handle)
        tCCR_restart();
}
#endif