Deactivate deco gas calculation option:
In the previous version had the option to consider a deco gas i the calculation or not. Reason for this was to have the automatic gas suggestion available while the deco calculation is still based on the current gas.
This might cause a critical situation in case the diver is not sure if the option is active or not => In the new version the TTS / deco is always calculated considering all deco gases.
line source
/**+ − ******************************************************************************+ − * @file stm32f4xx_hal_cryp.c+ − * @author MCD Application Team+ − * @brief CRYP HAL module driver.+ − * This file provides firmware functions to manage the following + − * functionalities of the Cryptography (CRYP) peripheral:+ − * + Initialization and de-initialization functions+ − * + AES processing functions+ − * + DES processing functions+ − * + TDES processing functions+ − * + DMA callback functions+ − * + CRYP IRQ handler management+ − * + Peripheral State functions+ − *+ − @verbatim+ − ==============================================================================+ − ##### How to use this driver #####+ − ==============================================================================+ − [..]+ − The CRYP HAL driver can be used as follows:+ − + − (#)Initialize the CRYP low level resources by implementing the HAL_CRYP_MspInit():+ − (##) Enable the CRYP interface clock using __HAL_RCC_CRYP_CLK_ENABLE()+ − (##) In case of using interrupts (e.g. HAL_CRYP_AESECB_Encrypt_IT())+ − (+++) Configure the CRYP interrupt priority using HAL_NVIC_SetPriority()+ − (+++) Enable the CRYP IRQ handler using HAL_NVIC_EnableIRQ()+ − (+++) In CRYP IRQ handler, call HAL_CRYP_IRQHandler()+ − (##) In case of using DMA to control data transfer (e.g. HAL_CRYP_AESECB_Encrypt_DMA())+ − (+++) Enable the DMAx interface clock using __DMAx_CLK_ENABLE()+ − (+++) Configure and enable two DMA streams one for managing data transfer from+ − memory to peripheral (input stream) and another stream for managing data+ − transfer from peripheral to memory (output stream)+ − (+++) Associate the initialized DMA handle to the CRYP DMA handle+ − using __HAL_LINKDMA()+ − (+++) Configure the priority and enable the NVIC for the transfer complete+ − interrupt on the two DMA Streams. The output stream should have higher+ − priority than the input stream HAL_NVIC_SetPriority() and HAL_NVIC_EnableIRQ()+ − + − (#)Initialize the CRYP HAL using HAL_CRYP_Init(). This function configures mainly:+ − (##) The data type: 1-bit, 8-bit, 16-bit and 32-bit+ − (##) The key size: 128, 192 and 256. This parameter is relevant only for AES+ − (##) The encryption/decryption key. It's size depends on the algorithm+ − used for encryption/decryption+ − (##) The initialization vector (counter). It is not used ECB mode.+ − + − (#)Three processing (encryption/decryption) functions are available:+ − (##) Polling mode: encryption and decryption APIs are blocking functions+ − i.e. they process the data and wait till the processing is finished,+ − e.g. HAL_CRYP_AESCBC_Encrypt()+ − (##) Interrupt mode: encryption and decryption APIs are not blocking functions+ − i.e. they process the data under interrupt,+ − e.g. HAL_CRYP_AESCBC_Encrypt_IT()+ − (##) DMA mode: encryption and decryption APIs are not blocking functions+ − i.e. the data transfer is ensured by DMA,+ − e.g. HAL_CRYP_AESCBC_Encrypt_DMA()+ − + − (#)When the processing function is called at first time after HAL_CRYP_Init()+ − the CRYP peripheral is initialized and processes the buffer in input.+ − At second call, the processing function performs an append of the already+ − processed buffer.+ − When a new data block is to be processed, call HAL_CRYP_Init() then the+ − processing function.+ − + − (#)Call HAL_CRYP_DeInit() to deinitialize the CRYP peripheral.+ − + − @endverbatim+ − ******************************************************************************+ − * @attention+ − *+ − * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2>+ − *+ − * Redistribution and use in source and binary forms, with or without modification,+ − * are permitted provided that the following conditions are met:+ − * 1. Redistributions of source code must retain the above copyright notice,+ − * this list of conditions and the following disclaimer.+ − * 2. Redistributions in binary form must reproduce the above copyright notice,+ − * this list of conditions and the following disclaimer in the documentation+ − * and/or other materials provided with the distribution.+ − * 3. Neither the name of STMicroelectronics nor the names of its contributors+ − * may be used to endorse or promote products derived from this software+ − * without specific prior written permission.+ − *+ − * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"+ − * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE+ − * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE+ − * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE+ − * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL+ − * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR+ − * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER+ − * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,+ − * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE+ − * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.+ − *+ − ******************************************************************************+ − */ + − + − /* Includes ------------------------------------------------------------------*/+ − #include "stm32f4xx_hal.h"+ − + − /** @addtogroup STM32F4xx_HAL_Driver+ − * @{+ − */+ − + − #ifdef HAL_CRYP_MODULE_ENABLED+ − + − #if defined(CRYP)+ − + − /** @defgroup CRYP CRYP+ − * @brief CRYP HAL module driver.+ − * @{+ − */+ − + − /* Private typedef -----------------------------------------------------------*/+ − /* Private define ------------------------------------------------------------*/+ − /** @addtogroup CRYP_Private_define+ − * @{+ − */+ − #define CRYP_TIMEOUT_VALUE 1U+ − /**+ − * @}+ − */ + − + − /* Private macro -------------------------------------------------------------*/+ − /* Private variables ---------------------------------------------------------*/+ − /* Private function prototypes -----------------------------------------------*/+ − /** @addtogroup CRYP_Private_Functions_prototypes+ − * @{+ − */ + − static void CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp, uint8_t *InitVector, uint32_t IVSize);+ − static void CRYP_SetKey(CRYP_HandleTypeDef *hcryp, uint8_t *Key, uint32_t KeySize);+ − static HAL_StatusTypeDef CRYP_ProcessData(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout);+ − static HAL_StatusTypeDef CRYP_ProcessData2Words(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout);+ − static void CRYP_DMAInCplt(DMA_HandleTypeDef *hdma);+ − static void CRYP_DMAOutCplt(DMA_HandleTypeDef *hdma);+ − static void CRYP_DMAError(DMA_HandleTypeDef *hdma);+ − static void CRYP_SetDMAConfig(CRYP_HandleTypeDef *hcryp, uint32_t inputaddr, uint16_t Size, uint32_t outputaddr);+ − static void CRYP_SetTDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction);+ − static void CRYP_SetTDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction);+ − static void CRYP_SetDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction);+ − static void CRYP_SetDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction);+ − /**+ − * @}+ − */ + − + − + − /* Private functions ---------------------------------------------------------*/+ − + − /** @addtogroup CRYP_Private_Functions+ − * @{+ − */+ − + − + − /**+ − * @brief DMA CRYP Input Data process complete callback.+ − * @param hdma DMA handle+ − * @retval None+ − */+ − static void CRYP_DMAInCplt(DMA_HandleTypeDef *hdma) + − {+ − CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent;+ − + − /* Disable the DMA transfer for input FIFO request by resetting the DIEN bit+ − in the DMACR register */+ − hcryp->Instance->DMACR &= (uint32_t)(~CRYP_DMACR_DIEN);+ − + − /* Call input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − + − /**+ − * @brief DMA CRYP Output Data process complete callback.+ − * @param hdma DMA handle+ − * @retval None+ − */+ − static void CRYP_DMAOutCplt(DMA_HandleTypeDef *hdma)+ − {+ − CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent;+ − + − /* Disable the DMA transfer for output FIFO request by resetting the DOEN bit+ − in the DMACR register */+ − hcryp->Instance->DMACR &= (uint32_t)(~CRYP_DMACR_DOEN);+ − + − /* Disable CRYP */+ − __HAL_CRYP_DISABLE(hcryp);+ − + − /* Change the CRYP state to ready */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Call output data transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − + − /**+ − * @brief DMA CRYP communication error callback. + − * @param hdma DMA handle+ − * @retval None+ − */+ − static void CRYP_DMAError(DMA_HandleTypeDef *hdma)+ − {+ − CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent;+ − hcryp->State= HAL_CRYP_STATE_READY;+ − HAL_CRYP_ErrorCallback(hcryp);+ − }+ − + − /**+ − * @brief Writes the Key in Key registers. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param Key Pointer to Key buffer+ − * @param KeySize Size of Key+ − * @retval None+ − */+ − static void CRYP_SetKey(CRYP_HandleTypeDef *hcryp, uint8_t *Key, uint32_t KeySize)+ − {+ − uint32_t keyaddr = (uint32_t)Key;+ − + − switch(KeySize)+ − {+ − case CRYP_KEYSIZE_256B:+ − /* Key Initialisation */+ − hcryp->Instance->K0LR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K0RR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K1LR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K1RR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K2LR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K2RR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K3LR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K3RR = __REV(*(uint32_t*)(keyaddr));+ − break;+ − case CRYP_KEYSIZE_192B:+ − hcryp->Instance->K1LR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K1RR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K2LR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K2RR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K3LR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K3RR = __REV(*(uint32_t*)(keyaddr));+ − break;+ − case CRYP_KEYSIZE_128B: + − hcryp->Instance->K2LR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K2RR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K3LR = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->K3RR = __REV(*(uint32_t*)(keyaddr));+ − break;+ − default:+ − break;+ − }+ − }+ − + − /**+ − * @brief Writes the InitVector/InitCounter in IV registers. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param InitVector Pointer to InitVector/InitCounter buffer+ − * @param IVSize Size of the InitVector/InitCounter+ − * @retval None+ − */+ − static void CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp, uint8_t *InitVector, uint32_t IVSize)+ − {+ − uint32_t ivaddr = (uint32_t)InitVector;+ − + − switch(IVSize)+ − {+ − case CRYP_KEYSIZE_128B:+ − hcryp->Instance->IV0LR = __REV(*(uint32_t*)(ivaddr));+ − ivaddr+=4U;+ − hcryp->Instance->IV0RR = __REV(*(uint32_t*)(ivaddr));+ − ivaddr+=4U;+ − hcryp->Instance->IV1LR = __REV(*(uint32_t*)(ivaddr));+ − ivaddr+=4U;+ − hcryp->Instance->IV1RR = __REV(*(uint32_t*)(ivaddr));+ − break;+ − /* Whatever key size 192 or 256, Init vector is written in IV0LR and IV0RR */+ − case CRYP_KEYSIZE_192B:+ − hcryp->Instance->IV0LR = __REV(*(uint32_t*)(ivaddr));+ − ivaddr+=4U;+ − hcryp->Instance->IV0RR = __REV(*(uint32_t*)(ivaddr));+ − break;+ − case CRYP_KEYSIZE_256B:+ − hcryp->Instance->IV0LR = __REV(*(uint32_t*)(ivaddr));+ − ivaddr+=4U;+ − hcryp->Instance->IV0RR = __REV(*(uint32_t*)(ivaddr));+ − break;+ − default:+ − break;+ − }+ − }+ − + − /**+ − * @brief Process Data: Writes Input data in polling mode and read the output data+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param Input Pointer to the Input buffer+ − * @param Ilength Length of the Input buffer, must be a multiple of 16.+ − * @param Output Pointer to the returned buffer+ − * @param Timeout Timeout value+ − * @retval None+ − */+ − static HAL_StatusTypeDef CRYP_ProcessData(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout)+ − {+ − uint32_t tickstart = 0U;+ − + − uint32_t i = 0U;+ − uint32_t inputaddr = (uint32_t)Input;+ − uint32_t outputaddr = (uint32_t)Output;+ − + − for(i=0U; (i < Ilength); i+=16U)+ − {+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − + − /* Get tick */+ − tickstart = HAL_GetTick();+ − + − while(HAL_IS_BIT_CLR(hcryp->Instance->SR, CRYP_FLAG_OFNE))+ − { + − /* Check for the Timeout */+ − if(Timeout != HAL_MAX_DELAY)+ − {+ − if((Timeout == 0U)||((HAL_GetTick() - tickstart ) > Timeout))+ − {+ − /* Change state */+ − hcryp->State = HAL_CRYP_STATE_TIMEOUT;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − return HAL_TIMEOUT;+ − }+ − }+ − }+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − }+ − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Process Data: Write Input data in polling mode. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param Input Pointer to the Input buffer+ − * @param Ilength Length of the Input buffer, must be a multiple of 8+ − * @param Output Pointer to the returned buffer+ − * @param Timeout Specify Timeout value + − * @retval None+ − */+ − static HAL_StatusTypeDef CRYP_ProcessData2Words(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout)+ − {+ − uint32_t tickstart = 0U; + − + − uint32_t i = 0U;+ − uint32_t inputaddr = (uint32_t)Input;+ − uint32_t outputaddr = (uint32_t)Output;+ − + − for(i=0U; (i < Ilength); i+=8U)+ − {+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − + − /* Get tick */+ − tickstart = HAL_GetTick();+ − + − while(HAL_IS_BIT_CLR(hcryp->Instance->SR, CRYP_FLAG_OFNE))+ − {+ − /* Check for the Timeout */+ − if(Timeout != HAL_MAX_DELAY)+ − {+ − if((Timeout == 0U)||((HAL_GetTick() - tickstart ) > Timeout))+ − {+ − /* Change state */+ − hcryp->State = HAL_CRYP_STATE_TIMEOUT;+ − + − /* Process Unlocked */ + − __HAL_UNLOCK(hcryp);+ − + − return HAL_TIMEOUT;+ − }+ − }+ − }+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − }+ − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Set the DMA configuration and start the DMA transfer+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param inputaddr address of the Input buffer+ − * @param Size Size of the Input buffer, must be a multiple of 16.+ − * @param outputaddr address of the Output buffer+ − * @retval None+ − */+ − static void CRYP_SetDMAConfig(CRYP_HandleTypeDef *hcryp, uint32_t inputaddr, uint16_t Size, uint32_t outputaddr)+ − {+ − /* Set the CRYP DMA transfer complete callback */+ − hcryp->hdmain->XferCpltCallback = CRYP_DMAInCplt;+ − /* Set the DMA error callback */+ − hcryp->hdmain->XferErrorCallback = CRYP_DMAError;+ − + − /* Set the CRYP DMA transfer complete callback */+ − hcryp->hdmaout->XferCpltCallback = CRYP_DMAOutCplt;+ − /* Set the DMA error callback */+ − hcryp->hdmaout->XferErrorCallback = CRYP_DMAError;+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Enable the DMA In DMA Stream */+ − HAL_DMA_Start_IT(hcryp->hdmain, inputaddr, (uint32_t)&hcryp->Instance->DR, Size/4U);+ − + − /* Enable In DMA request */+ − hcryp->Instance->DMACR = (CRYP_DMACR_DIEN);+ − + − /* Enable the DMA Out DMA Stream */+ − HAL_DMA_Start_IT(hcryp->hdmaout, (uint32_t)&hcryp->Instance->DOUT, outputaddr, Size/4U);+ − + − /* Enable Out DMA request */+ − hcryp->Instance->DMACR |= CRYP_DMACR_DOEN;+ − + − }+ − + − /**+ − * @brief Sets the CRYP peripheral in DES ECB mode.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param Direction Encryption or decryption+ − * @retval None+ − */+ − static void CRYP_SetDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction)+ − {+ − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the CRYP peripheral in AES ECB mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_DES_ECB | Direction);+ − + − /* Set the key */+ − hcryp->Instance->K1LR = __REV(*(uint32_t*)(hcryp->Init.pKey));+ − hcryp->Instance->K1RR = __REV(*(uint32_t*)(hcryp->Init.pKey+4U));+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − }+ − + − /**+ − * @brief Sets the CRYP peripheral in DES CBC mode.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param Direction Encryption or decryption+ − * @retval None+ − */+ − static void CRYP_SetDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction)+ − {+ − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the CRYP peripheral in AES ECB mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_DES_CBC | Direction);+ − + − /* Set the key */+ − hcryp->Instance->K1LR = __REV(*(uint32_t*)(hcryp->Init.pKey));+ − hcryp->Instance->K1RR = __REV(*(uint32_t*)(hcryp->Init.pKey+4U));+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_256B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − }+ − + − /**+ − * @brief Sets the CRYP peripheral in TDES ECB mode.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param Direction Encryption or decryption+ − * @retval None+ − */+ − static void CRYP_SetTDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction)+ − {+ − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the CRYP peripheral in AES ECB mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_TDES_ECB | Direction);+ − + − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, CRYP_KEYSIZE_192B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − }+ − + − /**+ − * @brief Sets the CRYP peripheral in TDES CBC mode+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param Direction Encryption or decryption+ − * @retval None+ − */+ − static void CRYP_SetTDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction)+ − {+ − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the CRYP peripheral in AES CBC mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_TDES_CBC | Direction);+ − + − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, CRYP_KEYSIZE_192B);+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_256B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − }+ − + − /**+ − * @}+ − */ + − + − /* Exported functions --------------------------------------------------------*/+ − /** @addtogroup CRYP_Exported_Functions+ − * @{+ − */ + − + − /** @defgroup CRYP_Exported_Functions_Group1 Initialization and de-initialization functions + − * @brief Initialization and Configuration functions. + − *+ − @verbatim + − ==============================================================================+ − ##### Initialization and de-initialization functions #####+ − ==============================================================================+ − [..] This section provides functions allowing to:+ − (+) Initialize the CRYP according to the specified parameters + − in the CRYP_InitTypeDef and creates the associated handle+ − (+) DeInitialize the CRYP peripheral+ − (+) Initialize the CRYP MSP+ − (+) DeInitialize CRYP MSP + − + − @endverbatim+ − * @{+ − */+ − + − /**+ − * @brief Initializes the CRYP according to the specified+ − * parameters in the CRYP_InitTypeDef and creates the associated handle.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_Init(CRYP_HandleTypeDef *hcryp)+ − { + − /* Check the CRYP handle allocation */+ − if(hcryp == NULL)+ − {+ − return HAL_ERROR;+ − }+ − + − /* Check the parameters */+ − assert_param(IS_CRYP_KEYSIZE(hcryp->Init.KeySize));+ − assert_param(IS_CRYP_DATATYPE(hcryp->Init.DataType));+ − + − if(hcryp->State == HAL_CRYP_STATE_RESET)+ − {+ − /* Allocate lock resource and initialize it */+ − hcryp->Lock = HAL_UNLOCKED;+ − /* Init the low level hardware */+ − HAL_CRYP_MspInit(hcryp);+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set the key size and data type*/+ − CRYP->CR = (uint32_t) (hcryp->Init.KeySize | hcryp->Init.DataType);+ − + − /* Reset CrypInCount and CrypOutCount */+ − hcryp->CrypInCount = 0U;+ − hcryp->CrypOutCount = 0U;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Set the default CRYP phase */+ − hcryp->Phase = HAL_CRYP_PHASE_READY;+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief DeInitializes the CRYP peripheral. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DeInit(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Check the CRYP handle allocation */+ − if(hcryp == NULL)+ − {+ − return HAL_ERROR;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set the default CRYP phase */+ − hcryp->Phase = HAL_CRYP_PHASE_READY;+ − + − /* Reset CrypInCount and CrypOutCount */+ − hcryp->CrypInCount = 0U;+ − hcryp->CrypOutCount = 0U;+ − + − /* Disable the CRYP Peripheral Clock */+ − __HAL_CRYP_DISABLE(hcryp);+ − + − /* DeInit the low level hardware: CLOCK, NVIC.*/+ − HAL_CRYP_MspDeInit(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_RESET;+ − + − /* Release Lock */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP MSP.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − __weak void HAL_CRYP_MspInit(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Prevent unused argument(s) compilation warning */+ − UNUSED(hcryp);+ − /* NOTE : This function Should not be modified, when the callback is needed,+ − the HAL_CRYP_MspInit could be implemented in the user file+ − */+ − }+ − + − /**+ − * @brief DeInitializes CRYP MSP.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − __weak void HAL_CRYP_MspDeInit(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Prevent unused argument(s) compilation warning */+ − UNUSED(hcryp);+ − /* NOTE : This function Should not be modified, when the callback is needed,+ − the HAL_CRYP_MspDeInit could be implemented in the user file+ − */+ − }+ − + − /**+ − * @}+ − */+ − + − /** @defgroup CRYP_Exported_Functions_Group2 AES processing functions + − * @brief processing functions. + − *+ − @verbatim + − ==============================================================================+ − ##### AES processing functions #####+ − ============================================================================== + − [..] This section provides functions allowing to:+ − (+) Encrypt plaintext using AES-128/192/256 using chaining modes+ − (+) Decrypt cyphertext using AES-128/192/256 using chaining modes+ − [..] Three processing functions are available:+ − (+) Polling mode+ − (+) Interrupt mode+ − (+) DMA mode+ − + − @endverbatim+ − * @{+ − */+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES ECB encryption mode+ − * then encrypt pPlainData. The cypher data are available in pCypherData+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES ECB mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Write Plain Data and Get Cypher Data */+ − if(CRYP_ProcessData(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES CBC encryption mode+ − * then encrypt pPlainData. The cypher data are available in pCypherData+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES ECB mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC);+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Write Plain Data and Get Cypher Data */+ − if(CRYP_ProcessData(hcryp,pPlainData, Size, pCypherData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES CTR encryption mode+ − * then encrypt pPlainData. The cypher data are available in pCypherData+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)+ − { + − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES ECB mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR);+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Write Plain Data and Get Cypher Data */+ − if(CRYP_ProcessData(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − + − + − /**+ − * @brief Initializes the CRYP peripheral in AES ECB decryption mode+ − * then decrypted pCypherData. The cypher data are available in pPlainData+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16.+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)+ − {+ − uint32_t tickstart = 0U;+ − + − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES Key mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Get tick */ + − tickstart = HAL_GetTick();+ − + − while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY))+ − {+ − /* Check for the Timeout */+ − if(Timeout != HAL_MAX_DELAY)+ − {+ − if((Timeout == 0U)||((HAL_GetTick() - tickstart ) > Timeout))+ − {+ − /* Change state */+ − hcryp->State = HAL_CRYP_STATE_TIMEOUT;+ − + − /* Process Unlocked */ + − __HAL_UNLOCK(hcryp);+ − + − return HAL_TIMEOUT;+ − }+ − }+ − }+ − + − /* Disable CRYP */+ − __HAL_CRYP_DISABLE(hcryp);+ − + − /* Reset the ALGOMODE bits*/+ − CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE);+ − + − /* Set the CRYP peripheral in AES ECB decryption mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB | CRYP_CR_ALGODIR);+ − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Write Plain Data and Get Cypher Data */+ − if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES ECB decryption mode+ − * then decrypted pCypherData. The cypher data are available in pPlainData+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16.+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)+ − {+ − uint32_t tickstart = 0U;+ − + − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES Key mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Get tick */ + − tickstart = HAL_GetTick();+ − + − while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY))+ − {+ − /* Check for the Timeout */+ − if(Timeout != HAL_MAX_DELAY)+ − {+ − if((Timeout == 0U)||((HAL_GetTick() - tickstart ) > Timeout))+ − {+ − /* Change state */+ − hcryp->State = HAL_CRYP_STATE_TIMEOUT;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − return HAL_TIMEOUT;+ − }+ − }+ − }+ − + − /* Reset the ALGOMODE bits*/+ − CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE);+ − + − /* Set the CRYP peripheral in AES CBC decryption mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC | CRYP_CR_ALGODIR);+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Write Plain Data and Get Cypher Data */+ − if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES CTR decryption mode+ − * then decrypted pCypherData. The cypher data are available in pPlainData+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16.+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)+ − { + − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES CTR mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR | CRYP_CR_ALGODIR);+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Write Plain Data and Get Cypher Data */+ − if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES ECB encryption mode using Interrupt.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16 bytes+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pPlainData;+ − hcryp->pCrypOutBuffPtr = pCypherData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES ECB mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − hcryp->pCrypInBuffPtr += 16U;+ − hcryp->CrypInCount -= 16U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − hcryp->pCrypOutBuffPtr += 16U;+ − hcryp->CrypOutCount -= 16U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Process Locked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call Input transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES CBC encryption mode using Interrupt.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16 bytes+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pPlainData;+ − hcryp->pCrypOutBuffPtr = pCypherData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − { + − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES CBC mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC);+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − hcryp->pCrypInBuffPtr += 16U;+ − hcryp->CrypInCount -= 16U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − hcryp->pCrypOutBuffPtr += 16U;+ − hcryp->CrypOutCount -= 16U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Process Locked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call Input transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES CTR encryption mode using Interrupt.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16 bytes+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pPlainData;+ − hcryp->pCrypOutBuffPtr = pCypherData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES CTR mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR);+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − hcryp->pCrypInBuffPtr += 16U;+ − hcryp->CrypInCount -= 16U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − hcryp->pCrypOutBuffPtr += 16U;+ − hcryp->CrypOutCount -= 16U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call Input transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − + − /**+ − * @brief Initializes the CRYP peripheral in AES ECB decryption mode using Interrupt.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16.+ − * @param pPlainData Pointer to the plaintext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − uint32_t tickstart = 0U;+ − + − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pCypherData;+ − hcryp->pCrypOutBuffPtr = pPlainData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES Key mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR);+ − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Get tick */ + − tickstart = HAL_GetTick();+ − + − while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY))+ − {+ − /* Check for the Timeout */+ − if((HAL_GetTick() - tickstart ) > CRYP_TIMEOUT_VALUE)+ − {+ − /* Change state */+ − hcryp->State = HAL_CRYP_STATE_TIMEOUT;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − return HAL_TIMEOUT;+ − }+ − }+ − + − /* Reset the ALGOMODE bits*/+ − CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE);+ − + − /* Set the CRYP peripheral in AES ECB decryption mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB | CRYP_CR_ALGODIR);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − hcryp->pCrypInBuffPtr += 16U;+ − hcryp->CrypInCount -= 16U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − hcryp->pCrypOutBuffPtr += 16U;+ − hcryp->CrypOutCount -= 16U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call Input transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES CBC decryption mode using IT.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16+ − * @param pPlainData Pointer to the plaintext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − + − uint32_t tickstart = 0U; + − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Get the buffer addresses and sizes */ + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pCypherData;+ − hcryp->pCrypOutBuffPtr = pPlainData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES Key mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Get tick */+ − tickstart = HAL_GetTick();+ − + − while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY))+ − {+ − /* Check for the Timeout */+ − if((HAL_GetTick() - tickstart ) > CRYP_TIMEOUT_VALUE)+ − {+ − /* Change state */+ − hcryp->State = HAL_CRYP_STATE_TIMEOUT;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − return HAL_TIMEOUT;+ − }+ − }+ − + − /* Reset the ALGOMODE bits*/+ − CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE);+ − + − /* Set the CRYP peripheral in AES CBC decryption mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC | CRYP_CR_ALGODIR);+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − hcryp->pCrypInBuffPtr += 16U;+ − hcryp->CrypInCount -= 16U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − hcryp->pCrypOutBuffPtr += 16U;+ − hcryp->CrypOutCount -= 16U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call Input transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES CTR decryption mode using Interrupt.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16+ − * @param pPlainData Pointer to the plaintext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Get the buffer addresses and sizes */ + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pCypherData;+ − hcryp->pCrypOutBuffPtr = pPlainData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES CTR mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR | CRYP_CR_ALGODIR);+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − hcryp->pCrypInBuffPtr += 16U;+ − hcryp->CrypInCount -= 16U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − hcryp->pCrypOutBuffPtr += 16U;+ − hcryp->CrypOutCount -= 16U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call Input transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES ECB encryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16 bytes+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pPlainData;+ − outputaddr = (uint32_t)pCypherData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES ECB mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES CBC encryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pPlainData;+ − outputaddr = (uint32_t)pCypherData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES ECB mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC);+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES CTR encryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pPlainData;+ − outputaddr = (uint32_t)pCypherData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES ECB mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR);+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES ECB decryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16 bytes+ − * @param pPlainData Pointer to the plaintext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − uint32_t tickstart = 0U; + − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pCypherData;+ − outputaddr = (uint32_t)pPlainData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES Key mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Get tick */+ − tickstart = HAL_GetTick();+ − + − while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY))+ − {+ − /* Check for the Timeout */+ − if((HAL_GetTick() - tickstart ) > CRYP_TIMEOUT_VALUE)+ − {+ − /* Change state */+ − hcryp->State = HAL_CRYP_STATE_TIMEOUT;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − return HAL_TIMEOUT;+ − }+ − }+ − + − /* Reset the ALGOMODE bits*/+ − CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE);+ − + − /* Set the CRYP peripheral in AES ECB decryption mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB | CRYP_CR_ALGODIR);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES CBC encryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16 bytes+ − * @param pPlainData Pointer to the plaintext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − uint32_t tickstart = 0U; + − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pCypherData;+ − outputaddr = (uint32_t)pPlainData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES Key mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Get tick */+ − tickstart = HAL_GetTick();+ − + − while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY))+ − {+ − /* Check for the Timeout */+ − if((HAL_GetTick() - tickstart ) > CRYP_TIMEOUT_VALUE)+ − {+ − /* Change state */+ − hcryp->State = HAL_CRYP_STATE_TIMEOUT;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − return HAL_TIMEOUT;+ − }+ − }+ − + − /* Reset the ALGOMODE bits*/+ − CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE);+ − + − /* Set the CRYP peripheral in AES CBC decryption mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC | CRYP_CR_ALGODIR);+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in AES CTR decryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16+ − * @param pPlainData Pointer to the plaintext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − { + − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pCypherData;+ − outputaddr = (uint32_t)pPlainData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Check if initialization phase has already been performed */+ − if(hcryp->Phase == HAL_CRYP_PHASE_READY)+ − {+ − /* Set the key */+ − CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);+ − + − /* Set the CRYP peripheral in AES CTR mode */+ − __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR | CRYP_CR_ALGODIR);+ − + − /* Set the Initialization Vector */+ − CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);+ − + − /* Flush FIFO */+ − __HAL_CRYP_FIFO_FLUSH(hcryp);+ − + − /* Set the phase */+ − hcryp->Phase = HAL_CRYP_PHASE_PROCESS;+ − }+ − + − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − + − /**+ − * @}+ − */+ − + − /** @defgroup CRYP_Exported_Functions_Group3 DES processing functions + − * @brief processing functions. + − *+ − @verbatim + − ==============================================================================+ − ##### DES processing functions #####+ − ============================================================================== + − [..] This section provides functions allowing to:+ − (+) Encrypt plaintext using DES using ECB or CBC chaining modes+ − (+) Decrypt cyphertext using ECB or CBC chaining modes+ − [..] Three processing functions are available:+ − (+) Polling mode+ − (+) Interrupt mode+ − (+) DMA mode+ − + − @endverbatim+ − * @{+ − */+ − + − /**+ − * @brief Initializes the CRYP peripheral in DES ECB encryption mode.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in DES ECB encryption mode */+ − CRYP_SetDESECBMode(hcryp, 0U);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Write Plain Data and Get Cypher Data */+ − if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in DES ECB decryption mode.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in DES ECB decryption mode */+ − CRYP_SetDESECBMode(hcryp, CRYP_CR_ALGODIR);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Write Plain Data and Get Cypher Data */+ − if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in DES CBC encryption mode.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in DES CBC encryption mode */+ − CRYP_SetDESCBCMode(hcryp, 0U);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Write Plain Data and Get Cypher Data */+ − if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in DES ECB decryption mode.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in DES CBC decryption mode */+ − CRYP_SetDESCBCMode(hcryp, CRYP_CR_ALGODIR);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Write Plain Data and Get Cypher Data */+ − if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in DES ECB encryption mode using IT.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pPlainData;+ − hcryp->pCrypOutBuffPtr = pCypherData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in DES ECB encryption mode */+ − CRYP_SetDESECBMode(hcryp, 0U);+ − + − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − + − hcryp->pCrypInBuffPtr += 8U;+ − hcryp->CrypInCount -= 8U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − + − hcryp->pCrypOutBuffPtr += 8U;+ − hcryp->CrypOutCount -= 8U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − /* Disable IT */+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Disable CRYP */+ − __HAL_CRYP_DISABLE(hcryp);+ − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call Input transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in DES CBC encryption mode using interrupt.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pPlainData;+ − hcryp->pCrypOutBuffPtr = pCypherData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in DES CBC encryption mode */+ − CRYP_SetDESCBCMode(hcryp, 0U);+ − + − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − + − hcryp->pCrypInBuffPtr += 8U;+ − hcryp->CrypInCount -= 8U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − + − hcryp->pCrypOutBuffPtr += 8U;+ − hcryp->CrypOutCount -= 8U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − /* Disable IT */+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Disable CRYP */+ − __HAL_CRYP_DISABLE(hcryp);+ − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call Input transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in DES ECB decryption mode using IT.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pCypherData;+ − hcryp->pCrypOutBuffPtr = pPlainData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in DES ECB decryption mode */+ − CRYP_SetDESECBMode(hcryp, CRYP_CR_ALGODIR);+ − + − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − + − hcryp->pCrypInBuffPtr += 8U;+ − hcryp->CrypInCount -= 8U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − + − hcryp->pCrypOutBuffPtr += 8U;+ − hcryp->CrypOutCount -= 8U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − /* Disable IT */+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Disable CRYP */+ − __HAL_CRYP_DISABLE(hcryp);+ − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call Input transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in DES ECB decryption mode using interrupt.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pCypherData;+ − hcryp->pCrypOutBuffPtr = pPlainData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in DES CBC decryption mode */+ − CRYP_SetDESCBCMode(hcryp, CRYP_CR_ALGODIR);+ − + − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − + − hcryp->pCrypInBuffPtr += 8U;+ − hcryp->CrypInCount -= 8U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − + − hcryp->pCrypOutBuffPtr += 8U;+ − hcryp->CrypOutCount -= 8U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − /* Disable IT */+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Disable CRYP */+ − __HAL_CRYP_DISABLE(hcryp);+ − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call Input transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in DES ECB encryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pPlainData;+ − outputaddr = (uint32_t)pCypherData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in DES ECB encryption mode */+ − CRYP_SetDESECBMode(hcryp, 0U);+ − + − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in DES CBC encryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pPlainData;+ − outputaddr = (uint32_t)pCypherData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in DES CBC encryption mode */+ − CRYP_SetDESCBCMode(hcryp, 0U);+ − + − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in DES ECB decryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pCypherData;+ − outputaddr = (uint32_t)pPlainData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in DES ECB decryption mode */+ − CRYP_SetDESECBMode(hcryp, CRYP_CR_ALGODIR);+ − + − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in DES ECB decryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pCypherData;+ − outputaddr = (uint32_t)pPlainData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in DES CBC decryption mode */+ − CRYP_SetDESCBCMode(hcryp, CRYP_CR_ALGODIR);+ − + − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − /**+ − * @}+ − */+ − + − /** @defgroup CRYP_Exported_Functions_Group4 TDES processing functions + − * @brief processing functions. + − *+ − @verbatim + − ==============================================================================+ − ##### TDES processing functions #####+ − ============================================================================== + − [..] This section provides functions allowing to:+ − (+) Encrypt plaintext using TDES based on ECB or CBC chaining modes+ − (+) Decrypt cyphertext using TDES based on ECB or CBC chaining modes+ − [..] Three processing functions are available:+ − (+) Polling mode+ − (+) Interrupt mode+ − (+) DMA mode+ − + − @endverbatim+ − * @{+ − */+ − + − /**+ − * @brief Initializes the CRYP peripheral in TDES ECB encryption mode+ − * then encrypt pPlainData. The cypher data are available in pCypherData+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_TDESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in TDES ECB encryption mode */+ − CRYP_SetTDESECBMode(hcryp, 0U);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Write Plain Data and Get Cypher Data */+ − if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in TDES ECB decryption mode+ − * then decrypted pCypherData. The cypher data are available in pPlainData+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_TDESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)+ − { + − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in TDES ECB decryption mode */+ − CRYP_SetTDESECBMode(hcryp, CRYP_CR_ALGODIR);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Write Cypher Data and Get Plain Data */+ − if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in TDES CBC encryption mode+ − * then encrypt pPlainData. The cypher data are available in pCypherData+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_TDESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in TDES CBC encryption mode */+ − CRYP_SetTDESCBCMode(hcryp, 0U);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Write Plain Data and Get Cypher Data */+ − if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in TDES CBC decryption mode+ − * then decrypted pCypherData. The cypher data are available in pPlainData+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Timeout Specify Timeout value + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_TDESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in TDES CBC decryption mode */+ − CRYP_SetTDESCBCMode(hcryp, CRYP_CR_ALGODIR);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Write Cypher Data and Get Plain Data */+ − if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK)+ − {+ − return HAL_TIMEOUT;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in TDES ECB encryption mode using interrupt.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_TDESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pPlainData;+ − hcryp->pCrypOutBuffPtr = pCypherData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in TDES ECB encryption mode */+ − CRYP_SetTDESECBMode(hcryp, 0U);+ − + − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − + − hcryp->pCrypInBuffPtr += 8U;+ − hcryp->CrypInCount -= 8U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − + − hcryp->pCrypOutBuffPtr += 8U;+ − hcryp->CrypOutCount -= 8U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − /* Disable IT */+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Disable CRYP */+ − __HAL_CRYP_DISABLE(hcryp);+ − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call the Output data transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in TDES CBC encryption mode.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_TDESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pPlainData;+ − hcryp->pCrypOutBuffPtr = pCypherData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in TDES CBC encryption mode */+ − CRYP_SetTDESCBCMode(hcryp, 0U);+ − + − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − + − hcryp->pCrypInBuffPtr += 8U;+ − hcryp->CrypInCount -= 8U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − + − hcryp->pCrypOutBuffPtr += 8U;+ − hcryp->CrypOutCount -= 8U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Disable CRYP */+ − __HAL_CRYP_DISABLE(hcryp);+ − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call Input transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in TDES ECB decryption mode.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_TDESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pCypherData;+ − hcryp->pCrypOutBuffPtr = pPlainData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in TDES ECB decryption mode */+ − CRYP_SetTDESECBMode(hcryp, CRYP_CR_ALGODIR);+ − + − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − + − hcryp->pCrypInBuffPtr += 8U;+ − hcryp->CrypInCount -= 8U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − + − hcryp->pCrypOutBuffPtr += 8U;+ − hcryp->CrypOutCount -= 8U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Disable CRYP */+ − __HAL_CRYP_DISABLE(hcryp);+ − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call Input transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − } + − + − /**+ − * @brief Initializes the CRYP peripheral in TDES CBC decryption mode.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pPlainData Pointer to the plaintext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_TDESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if(hcryp->State == HAL_CRYP_STATE_READY)+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − hcryp->CrypInCount = Size;+ − hcryp->pCrypInBuffPtr = pCypherData;+ − hcryp->pCrypOutBuffPtr = pPlainData;+ − hcryp->CrypOutCount = Size;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in TDES CBC decryption mode */+ − CRYP_SetTDESCBCMode(hcryp, CRYP_CR_ALGODIR);+ − + − /* Enable Interrupts */+ − __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI);+ − + − /* Enable CRYP */+ − __HAL_CRYP_ENABLE(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI))+ − {+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − /* Write the Input block in the IN FIFO */+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DR = *(uint32_t*)(inputaddr);+ − + − hcryp->pCrypInBuffPtr += 8U;+ − hcryp->CrypInCount -= 8U;+ − if(hcryp->CrypInCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI);+ − /* Call the Input data transfer complete callback */+ − HAL_CRYP_InCpltCallback(hcryp);+ − }+ − }+ − else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI))+ − {+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − /* Read the Output block from the Output FIFO */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT;+ − + − hcryp->pCrypOutBuffPtr += 8U;+ − hcryp->CrypOutCount -= 8U;+ − if(hcryp->CrypOutCount == 0U)+ − {+ − __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI);+ − /* Disable CRYP */+ − __HAL_CRYP_DISABLE(hcryp);+ − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − /* Call Input transfer complete callback */+ − HAL_CRYP_OutCpltCallback(hcryp);+ − }+ − }+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in TDES ECB encryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_TDESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pPlainData;+ − outputaddr = (uint32_t)pCypherData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in TDES ECB encryption mode */+ − CRYP_SetTDESECBMode(hcryp, 0U);+ − + − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in TDES CBC encryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_TDESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pPlainData;+ − outputaddr = (uint32_t)pCypherData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in TDES CBC encryption mode */+ − CRYP_SetTDESCBCMode(hcryp, 0U);+ − + − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in TDES ECB decryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_TDESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pCypherData;+ − outputaddr = (uint32_t)pPlainData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in TDES ECB decryption mode */+ − CRYP_SetTDESECBMode(hcryp, CRYP_CR_ALGODIR);+ − + − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − /**+ − * @brief Initializes the CRYP peripheral in TDES CBC decryption mode using DMA.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 8+ − * @param pPlainData Pointer to the plaintext buffer+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_TDESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − uint32_t inputaddr;+ − uint32_t outputaddr;+ − + − if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))+ − {+ − /* Process Locked */+ − __HAL_LOCK(hcryp);+ − + − inputaddr = (uint32_t)pCypherData;+ − outputaddr = (uint32_t)pPlainData;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set CRYP peripheral in TDES CBC decryption mode */+ − CRYP_SetTDESCBCMode(hcryp, CRYP_CR_ALGODIR);+ − + − /* Set the input and output addresses and start DMA transfer */ + − CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − else+ − {+ − return HAL_ERROR; + − }+ − }+ − + − /**+ − * @}+ − */+ − + − /** @defgroup CRYP_Exported_Functions_Group5 DMA callback functions + − * @brief DMA callback functions. + − *+ − @verbatim + − ==============================================================================+ − ##### DMA callback functions #####+ − ============================================================================== + − [..] This section provides DMA callback functions:+ − (+) DMA Input data transfer complete+ − (+) DMA Output data transfer complete+ − (+) DMA error+ − + − @endverbatim+ − * @{+ − */+ − + − /**+ − * @brief Input FIFO transfer completed callbacks.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − __weak void HAL_CRYP_InCpltCallback(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Prevent unused argument(s) compilation warning */+ − UNUSED(hcryp);+ − /* NOTE : This function Should not be modified, when the callback is needed,+ − the HAL_CRYP_InCpltCallback could be implemented in the user file+ − */ + − }+ − + − /**+ − * @brief Output FIFO transfer completed callbacks.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − __weak void HAL_CRYP_OutCpltCallback(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Prevent unused argument(s) compilation warning */+ − UNUSED(hcryp);+ − /* NOTE : This function Should not be modified, when the callback is needed,+ − the HAL_CRYP_OutCpltCallback could be implemented in the user file+ − */+ − }+ − + − /**+ − * @brief CRYP error callbacks.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − __weak void HAL_CRYP_ErrorCallback(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Prevent unused argument(s) compilation warning */+ − UNUSED(hcryp);+ − /* NOTE : This function Should not be modified, when the callback is needed,+ − the HAL_CRYP_ErrorCallback could be implemented in the user file+ − */ + − }+ − + − /**+ − * @}+ − */+ − + − /** @defgroup CRYP_Exported_Functions_Group6 CRYP IRQ handler management + − * @brief CRYP IRQ handler.+ − *+ − @verbatim + − ==============================================================================+ − ##### CRYP IRQ handler management #####+ − ============================================================================== + − [..] This section provides CRYP IRQ handler function.+ − + − @endverbatim+ − * @{+ − */+ − + − /**+ − * @brief This function handles CRYP interrupt request.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − void HAL_CRYP_IRQHandler(CRYP_HandleTypeDef *hcryp)+ − {+ − switch(CRYP->CR & CRYP_CR_ALGOMODE_DIRECTION)+ − {+ − case CRYP_CR_ALGOMODE_TDES_ECB_ENCRYPT:+ − HAL_CRYP_TDESECB_Encrypt_IT(hcryp, NULL, 0U, NULL);+ − break;+ − + − case CRYP_CR_ALGOMODE_TDES_ECB_DECRYPT:+ − HAL_CRYP_TDESECB_Decrypt_IT(hcryp, NULL, 0U, NULL);+ − break;+ − + − case CRYP_CR_ALGOMODE_TDES_CBC_ENCRYPT:+ − HAL_CRYP_TDESCBC_Encrypt_IT(hcryp, NULL, 0U, NULL);+ − break;+ − + − case CRYP_CR_ALGOMODE_TDES_CBC_DECRYPT:+ − HAL_CRYP_TDESCBC_Decrypt_IT(hcryp, NULL, 0U, NULL);+ − break;+ − + − case CRYP_CR_ALGOMODE_DES_ECB_ENCRYPT:+ − HAL_CRYP_DESECB_Encrypt_IT(hcryp, NULL, 0U, NULL);+ − break;+ − + − case CRYP_CR_ALGOMODE_DES_ECB_DECRYPT:+ − HAL_CRYP_DESECB_Decrypt_IT(hcryp, NULL, 0U, NULL);+ − break;+ − + − case CRYP_CR_ALGOMODE_DES_CBC_ENCRYPT:+ − HAL_CRYP_DESCBC_Encrypt_IT(hcryp, NULL, 0U, NULL);+ − break;+ − + − case CRYP_CR_ALGOMODE_DES_CBC_DECRYPT:+ − HAL_CRYP_DESCBC_Decrypt_IT(hcryp, NULL, 0U, NULL);+ − break;+ − + − case CRYP_CR_ALGOMODE_AES_ECB_ENCRYPT:+ − HAL_CRYP_AESECB_Encrypt_IT(hcryp, NULL, 0U, NULL);+ − break;+ − + − case CRYP_CR_ALGOMODE_AES_ECB_DECRYPT:+ − HAL_CRYP_AESECB_Decrypt_IT(hcryp, NULL, 0U, NULL);+ − break;+ − + − case CRYP_CR_ALGOMODE_AES_CBC_ENCRYPT:+ − HAL_CRYP_AESCBC_Encrypt_IT(hcryp, NULL, 0U, NULL);+ − break;+ − + − case CRYP_CR_ALGOMODE_AES_CBC_DECRYPT:+ − HAL_CRYP_AESCBC_Decrypt_IT(hcryp, NULL, 0U, NULL);+ − break;+ − + − case CRYP_CR_ALGOMODE_AES_CTR_ENCRYPT:+ − HAL_CRYP_AESCTR_Encrypt_IT(hcryp, NULL, 0U, NULL); + − break;+ − + − case CRYP_CR_ALGOMODE_AES_CTR_DECRYPT:+ − HAL_CRYP_AESCTR_Decrypt_IT(hcryp, NULL, 0U, NULL); + − break;+ − + − default:+ − break;+ − }+ − }+ − + − /**+ − * @}+ − */+ − + − /** @defgroup CRYP_Exported_Functions_Group7 Peripheral State functions + − * @brief Peripheral State functions. + − *+ − @verbatim + − ==============================================================================+ − ##### Peripheral State functions #####+ − ============================================================================== + − [..]+ − This subsection permits to get in run-time the status of the peripheral.+ − + − @endverbatim+ − * @{+ − */+ − + − /**+ − * @brief Returns the CRYP state.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval HAL state+ − */+ − HAL_CRYP_STATETypeDef HAL_CRYP_GetState(CRYP_HandleTypeDef *hcryp)+ − {+ − return hcryp->State;+ − }+ − + − /**+ − * @}+ − */+ − + − + − /**+ − * @}+ − */+ − + − #endif /* CRYP */+ − + − #if defined (AES)+ − + − /** @defgroup AES AES+ − * @brief AES HAL module driver.+ − * @{+ − */+ − + − /* Private typedef -----------------------------------------------------------*/+ − /* Private define ------------------------------------------------------------*/+ − /* Private macro -------------------------------------------------------------*/+ − /* Private variables ---------------------------------------------------------*/+ − /* Private functions --------------------------------------------------------*/+ − + − /** @defgroup CRYP_Private_Functions CRYP Private Functions+ − * @{+ − */+ − + − static HAL_StatusTypeDef CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp);+ − static HAL_StatusTypeDef CRYP_SetKey(CRYP_HandleTypeDef *hcryp);+ − static HAL_StatusTypeDef CRYP_AES_IT(CRYP_HandleTypeDef *hcryp);+ − + − /**+ − * @}+ − */+ − + − /* Exported functions ---------------------------------------------------------*/+ − + − /** @defgroup CRYP_Exported_Functions CRYP Exported Functions+ − * @{+ − */+ − + − /** @defgroup CRYP_Exported_Functions_Group1 Initialization and deinitialization functions + − * @brief Initialization and Configuration functions. + − *+ − @verbatim + − ==============================================================================+ − ##### Initialization and deinitialization functions #####+ − ==============================================================================+ − [..] This section provides functions allowing to:+ − (+) Initialize the CRYP according to the specified parameters + − in the CRYP_InitTypeDef and creates the associated handle+ − (+) DeInitialize the CRYP peripheral+ − (+) Initialize the CRYP MSP (MCU Specific Package)+ − (+) De-Initialize the CRYP MSP+ − + − [..]+ − (@) Specific care must be taken to format the key and the Initialization Vector IV!+ − + − [..] If the key is defined as a 128-bit long array key[127..0] = {b127 ... b0} where + − b127 is the MSB and b0 the LSB, the key must be stored in MCU memory + − (+) as a sequence of words where the MSB word comes first (occupies the+ − lowest memory address) + − (+) where each word is byte-swapped:+ − (++) address n+0 : 0b b103 .. b96 b111 .. b104 b119 .. b112 b127 .. b120+ − (++) address n+4 : 0b b71 .. b64 b79 .. b72 b87 .. b80 b95 .. b88+ − (++) address n+8 : 0b b39 .. b32 b47 .. b40 b55 .. b48 b63 .. b56+ − (++) address n+C : 0b b7 .. b0 b15 .. b8 b23 .. b16 b31 .. b24 + − [..] Hereafter, another illustration when considering a 128-bit long key made of 16 bytes {B15..B0}.+ − The 4 32-bit words that make the key must be stored as follows in MCU memory: + − (+) address n+0 : 0x B12 B13 B14 B15+ − (+) address n+4 : 0x B8 B9 B10 B11+ − (+) address n+8 : 0x B4 B5 B6 B7+ − (+) address n+C : 0x B0 B1 B2 B3 + − [..] which leads to the expected setting + − (+) AES_KEYR3 = 0x B15 B14 B13 B12 + − (+) AES_KEYR2 = 0x B11 B10 B9 B8 + − (+) AES_KEYR1 = 0x B7 B6 B5 B4 + − (+) AES_KEYR0 = 0x B3 B2 B1 B0 + − + − [..] Same format must be applied for a 256-bit long key made of 32 bytes {B31..B0}. + − The 8 32-bit words that make the key must be stored as follows in MCU memory:+ − (+) address n+00 : 0x B28 B29 B30 B31+ − (+) address n+04 : 0x B24 B25 B26 B27+ − (+) address n+08 : 0x B20 B21 B22 B23+ − (+) address n+0C : 0x B16 B17 B18 B19 + − (+) address n+10 : 0x B12 B13 B14 B15+ − (+) address n+14 : 0x B8 B9 B10 B11+ − (+) address n+18 : 0x B4 B5 B6 B7+ − (+) address n+1C : 0x B0 B1 B2 B3 + − [..] which leads to the expected setting + − (+) AES_KEYR7 = 0x B31 B30 B29 B28 + − (+) AES_KEYR6 = 0x B27 B26 B25 B24 + − (+) AES_KEYR5 = 0x B23 B22 B21 B20 + − (+) AES_KEYR4 = 0x B19 B18 B17 B16 + − (+) AES_KEYR3 = 0x B15 B14 B13 B12 + − (+) AES_KEYR2 = 0x B11 B10 B9 B8 + − (+) AES_KEYR1 = 0x B7 B6 B5 B4 + − (+) AES_KEYR0 = 0x B3 B2 B1 B0 + − + − [..] Initialization Vector IV (4 32-bit words) format must follow the same as + − that of a 128-bit long key. + − + − [..] + − + − @endverbatim+ − * @{+ − */+ − + − /**+ − * @brief Initialize the CRYP according to the specified+ − * parameters in the CRYP_InitTypeDef and initialize the associated handle. + − * @note Specific care must be taken to format the key and the Initialization Vector IV + − * stored in the MCU memory before calling HAL_CRYP_Init(). Refer to explanations + − * hereabove. + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_Init(CRYP_HandleTypeDef *hcryp)+ − { + − /* Check the CRYP handle allocation */+ − if(hcryp == NULL)+ − {+ − return HAL_ERROR;+ − }+ − + − /* Check the instance */+ − assert_param(IS_AES_ALL_INSTANCE(hcryp->Instance));+ − + − /* Check the parameters */+ − assert_param(IS_CRYP_KEYSIZE(hcryp->Init.KeySize));+ − assert_param(IS_CRYP_DATATYPE(hcryp->Init.DataType));+ − assert_param(IS_CRYP_ALGOMODE(hcryp->Init.OperatingMode));+ − /* ChainingMode parameter is irrelevant when mode is set to Key derivation */+ − if (hcryp->Init.OperatingMode != CRYP_ALGOMODE_KEYDERIVATION)+ − {+ − assert_param(IS_CRYP_CHAINMODE(hcryp->Init.ChainingMode));+ − }+ − assert_param(IS_CRYP_WRITE(hcryp->Init.KeyWriteFlag));+ − + − /*========================================================*/+ − /* Check the proper operating/chaining modes combinations */+ − /*========================================================*/ + − /* Check the proper chaining when the operating mode is key derivation and decryption */+ − #if defined(AES_CR_NPBLB)+ − if ((hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION_DECRYPT) &&\+ − ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CTR) \+ − || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) \+ − || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CCM_CMAC)))+ − #else + − if ((hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION_DECRYPT) &&\+ − ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CTR) \+ − || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) \+ − || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC)))+ − #endif + − {+ − return HAL_ERROR;+ − } + − /* Check that key derivation is not set in CMAC mode or CCM mode when applicable */ + − #if defined(AES_CR_NPBLB)+ − if ((hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION) + − && (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CCM_CMAC))+ − #else + − if ((hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION) + − && (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC))+ − #endif + − {+ − return HAL_ERROR;+ − }+ − + − + − /*================*/+ − /* Initialization */+ − /*================*/ + − /* Initialization start */+ − if(hcryp->State == HAL_CRYP_STATE_RESET)+ − {+ − /* Allocate lock resource and initialize it */+ − hcryp->Lock = HAL_UNLOCKED;+ − + − /* Init the low level hardware */+ − HAL_CRYP_MspInit(hcryp);+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY; + − + − /* Disable the Peripheral */+ − __HAL_CRYP_DISABLE();+ − + − /*=============================================================*/+ − /* AES initialization common to all operating modes */ + − /*=============================================================*/+ − /* Set the Key size selection */+ − MODIFY_REG(hcryp->Instance->CR, AES_CR_KEYSIZE, hcryp->Init.KeySize);+ − + − /* Set the default CRYP phase when this parameter is not used.+ − Phase is updated below in case of GCM/GMAC/CMAC(/CCM) setting. */+ − hcryp->Phase = HAL_CRYP_PHASE_NOT_USED;+ − + − + − + − /*=============================================================*/+ − /* Carry on the initialization based on the AES operating mode */ + − /*=============================================================*/+ − /* Key derivation */ + − if (hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION)+ − {+ − MODIFY_REG(hcryp->Instance->CR, AES_CR_MODE, CRYP_ALGOMODE_KEYDERIVATION);+ − + − /* Configure the Key registers */+ − if (CRYP_SetKey(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − }+ − else+ − /* Encryption / Decryption (with or without key derivation) / authentication */+ − { + − /* Set data type, operating and chaining modes.+ − In case of GCM or GMAC, data type is forced to 0b00 */+ − if (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC)+ − {+ − MODIFY_REG(hcryp->Instance->CR, AES_CR_DATATYPE|AES_CR_MODE|AES_CR_CHMOD, hcryp->Init.OperatingMode|hcryp->Init.ChainingMode);+ − }+ − else+ − {+ − MODIFY_REG(hcryp->Instance->CR, AES_CR_DATATYPE|AES_CR_MODE|AES_CR_CHMOD, hcryp->Init.DataType|hcryp->Init.OperatingMode|hcryp->Init.ChainingMode);+ − }+ − + − + − /* Specify the encryption/decryption phase in case of Galois counter mode (GCM), + − Galois message authentication code (GMAC), cipher message authentication code (CMAC) + − or Counter with Cipher Mode (CCM) when applicable */+ − #if defined(AES_CR_NPBLB) + − if ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC)+ − || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CCM_CMAC))+ − #else+ − if ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC)+ − || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC))+ − #endif + − {+ − MODIFY_REG(hcryp->Instance->CR, AES_CR_GCMPH, hcryp->Init.GCMCMACPhase);+ − hcryp->Phase = HAL_CRYP_PHASE_START;+ − }+ − + − + − /* Configure the Key registers if no need to bypass this step */+ − if (hcryp->Init.KeyWriteFlag == CRYP_KEY_WRITE_ENABLE)+ − {+ − if (CRYP_SetKey(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − } + − }+ − + − /* If applicable, configure the Initialization Vector */+ − if (hcryp->Init.ChainingMode != CRYP_CHAINMODE_AES_ECB)+ − {+ − if (CRYP_SetInitVector(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − }+ − }+ − + − #if defined(AES_CR_NPBLB) + − /* Clear NPBLB field */+ − CLEAR_BIT(hcryp->Instance->CR, AES_CR_NPBLB);+ − #endif + − + − /* Reset CrypInCount and CrypOutCount */+ − hcryp->CrypInCount = 0U;+ − hcryp->CrypOutCount = 0U;+ − + − /* Reset ErrorCode field */+ − hcryp->ErrorCode = HAL_CRYP_ERROR_NONE;+ − + − /* Reset Mode suspension request */+ − hcryp->SuspendRequest = HAL_CRYP_SUSPEND_NONE;+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Enable the Peripheral */+ − __HAL_CRYP_ENABLE();+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief DeInitialize the CRYP peripheral. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_DeInit(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Check the CRYP handle allocation */+ − if(hcryp == NULL)+ − {+ − return HAL_ERROR;+ − }+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_BUSY;+ − + − /* Set the default CRYP phase */+ − hcryp->Phase = HAL_CRYP_PHASE_READY;+ − + − /* Reset CrypInCount and CrypOutCount */+ − hcryp->CrypInCount = 0U;+ − hcryp->CrypOutCount = 0U;+ − + − /* Disable the CRYP Peripheral Clock */+ − __HAL_CRYP_DISABLE();+ − + − /* DeInit the low level hardware: CLOCK, NVIC.*/+ − HAL_CRYP_MspDeInit(hcryp);+ − + − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_RESET;+ − + − /* Release Lock */+ − __HAL_UNLOCK(hcryp);+ − + − /* Return function status */+ − return HAL_OK;+ − }+ − + − /**+ − * @brief Initialize the CRYP MSP.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − __weak void HAL_CRYP_MspInit(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Prevent unused argument(s) compilation warning */+ − UNUSED(hcryp);+ − + − /* NOTE : This function should not be modified; when the callback is needed,+ − the HAL_CRYP_MspInit can be implemented in the user file+ − */+ − }+ − + − /**+ − * @brief DeInitialize CRYP MSP.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − __weak void HAL_CRYP_MspDeInit(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Prevent unused argument(s) compilation warning */+ − UNUSED(hcryp);+ − + − /* NOTE : This function should not be modified; when the callback is needed,+ − the HAL_CRYP_MspDeInit can be implemented in the user file+ − */+ − }+ − + − /**+ − * @}+ − */+ − + − /** @defgroup CRYP_Exported_Functions_Group2 AES processing functions + − * @brief Processing functions. + − *+ − @verbatim + − ==============================================================================+ − ##### AES processing functions #####+ − ============================================================================== + − [..] This section provides functions allowing to:+ − (+) Encrypt plaintext using AES algorithm in different chaining modes+ − (+) Decrypt cyphertext using AES algorithm in different chaining modes+ − [..] Three processing functions are available:+ − (+) Polling mode+ − (+) Interrupt mode+ − (+) DMA mode+ − + − @endverbatim+ − * @{+ − */+ − + − + − /**+ − * @brief Encrypt pPlainData in AES ECB encryption mode. The cypher data are available in pCypherData.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Timeout Specify Timeout value + − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES() API instead (usage recommended). + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES(hcryp, pPlainData, Size, pCypherData, Timeout);+ − }+ − + − + − /**+ − * @brief Encrypt pPlainData in AES CBC encryption mode with key derivation. The cypher data are available in pCypherData.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Timeout Specify Timeout value+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES() API instead (usage recommended). + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)+ − { + − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES(hcryp, pPlainData, Size, pCypherData, Timeout);+ − }+ − + − + − /**+ − * @brief Encrypt pPlainData in AES CTR encryption mode. The cypher data are available in pCypherData+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Timeout Specify Timeout value + − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES() API instead (usage recommended). + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES(hcryp, pPlainData, Size, pCypherData, Timeout);+ − }+ − + − /**+ − * @brief Decrypt pCypherData in AES ECB decryption mode with key derivation, + − * the decyphered data are available in pPlainData.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Timeout Specify Timeout value + − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES() API instead (usage recommended). + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES(hcryp, pCypherData, Size, pPlainData, Timeout);+ − }+ − + − /**+ − * @brief Decrypt pCypherData in AES ECB decryption mode with key derivation, + − * the decyphered data are available in pPlainData.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Timeout Specify Timeout value + − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES() API instead (usage recommended). + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES(hcryp, pCypherData, Size, pPlainData, Timeout);+ − }+ − + − /**+ − * @brief Decrypt pCypherData in AES CTR decryption mode, + − * the decyphered data are available in pPlainData.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Timeout Specify Timeout value+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES() API instead (usage recommended). + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_DECRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − } + − + − return HAL_CRYPEx_AES(hcryp, pCypherData, Size, pPlainData, Timeout);+ − }+ − + − /**+ − * @brief Encrypt pPlainData in AES ECB encryption mode using Interrupt,+ − * the cypher data are available in pCypherData.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − } + − + − return HAL_CRYPEx_AES_IT(hcryp, pPlainData, Size, pCypherData);+ − }+ − + − /**+ − * @brief Encrypt pPlainData in AES CBC encryption mode using Interrupt,+ − * the cypher data are available in pCypherData. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES_IT(hcryp, pPlainData, Size, pCypherData);+ − }+ − + − + − /**+ − * @brief Encrypt pPlainData in AES CTR encryption mode using Interrupt,+ − * the cypher data are available in pCypherData. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES_IT(hcryp, pPlainData, Size, pCypherData);+ − }+ − + − /**+ − * @brief Decrypt pCypherData in AES ECB decryption mode using Interrupt,+ − * the decyphered data are available in pPlainData. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pPlainData Pointer to the plaintext buffer.+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES_IT(hcryp, pCypherData, Size, pPlainData);+ − }+ − + − /**+ − * @brief Decrypt pCypherData in AES CBC decryption mode using Interrupt,+ − * the decyphered data are available in pPlainData. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pPlainData Pointer to the plaintext buffer+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES_IT(hcryp, pCypherData, Size, pPlainData);+ − }+ − + − /**+ − * @brief Decrypt pCypherData in AES CTR decryption mode using Interrupt,+ − * the decyphered data are available in pPlainData. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pPlainData Pointer to the plaintext buffer+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_DECRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − } + − + − return HAL_CRYPEx_AES_IT(hcryp, pCypherData, Size, pPlainData);+ − }+ − + − /**+ − * @brief Encrypt pPlainData in AES ECB encryption mode using DMA,+ − * the cypher data are available in pCypherData. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended).+ − * @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES_DMA(hcryp, pPlainData, Size, pCypherData);+ − }+ − + − + − + − /**+ − * @brief Encrypt pPlainData in AES CBC encryption mode using DMA,+ − * the cypher data are available in pCypherData. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended).+ − * @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES_DMA(hcryp, pPlainData, Size, pCypherData);+ − }+ − + − /**+ − * @brief Encrypt pPlainData in AES CTR encryption mode using DMA,+ − * the cypher data are available in pCypherData. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pPlainData Pointer to the plaintext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pCypherData Pointer to the cyphertext buffer.+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended).+ − * @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES_DMA(hcryp, pPlainData, Size, pCypherData);+ − }+ − + − /**+ − * @brief Decrypt pCypherData in AES ECB decryption mode using DMA,+ − * the decyphered data are available in pPlainData. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pPlainData Pointer to the plaintext buffer+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). + − * @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES_DMA(hcryp, pCypherData, Size, pPlainData);+ − }+ − + − /**+ − * @brief Decrypt pCypherData in AES CBC decryption mode using DMA,+ − * the decyphered data are available in pPlainData. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pPlainData Pointer to the plaintext buffer+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended).+ − * @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − + − return HAL_CRYPEx_AES_DMA(hcryp, pCypherData, Size, pPlainData);+ − }+ − + − /**+ − * @brief Decrypt pCypherData in AES CTR decryption mode using DMA,+ − * the decyphered data are available in pPlainData. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @param pCypherData Pointer to the cyphertext buffer+ − * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16.+ − * @param pPlainData Pointer to the plaintext buffer+ − * @note This API is provided only to maintain compatibility with legacy software. Users should directly+ − * resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). + − * @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. + − * @retval HAL status+ − */+ − HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)+ − {+ − /* Re-initialize AES IP with proper parameters */+ − if (HAL_CRYP_DeInit(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − }+ − hcryp->Init.OperatingMode = CRYP_ALGOMODE_DECRYPT;+ − hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR;+ − hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE;+ − if (HAL_CRYP_Init(hcryp) != HAL_OK)+ − {+ − return HAL_ERROR;+ − } + − + − return HAL_CRYPEx_AES_DMA(hcryp, pCypherData, Size, pPlainData);+ − }+ − + − + − /**+ − * @}+ − */+ − + − /** @defgroup CRYP_Exported_Functions_Group3 Callback functions + − * @brief Callback functions. + − *+ − @verbatim + − ==============================================================================+ − ##### Callback functions #####+ − ============================================================================== + − [..] This section provides Interruption and DMA callback functions:+ − (+) DMA Input data transfer complete+ − (+) DMA Output data transfer complete+ − (+) DMA or Interrupt error+ − + − @endverbatim+ − * @{+ − */+ − + − /**+ − * @brief CRYP error callback.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − __weak void HAL_CRYP_ErrorCallback(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Prevent unused argument(s) compilation warning */+ − UNUSED(hcryp);+ − + − /* NOTE : This function should not be modified; when the callback is needed,+ − the HAL_CRYP_ErrorCallback can be implemented in the user file+ − */+ − }+ − + − /**+ − * @brief Input DMA transfer complete callback.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − __weak void HAL_CRYP_InCpltCallback(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Prevent unused argument(s) compilation warning */+ − UNUSED(hcryp);+ − + − /* NOTE : This function should not be modified; when the callback is needed,+ − the HAL_CRYP_InCpltCallback can be implemented in the user file+ − */+ − }+ − + − /**+ − * @brief Output DMA transfer complete callback.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − __weak void HAL_CRYP_OutCpltCallback(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Prevent unused argument(s) compilation warning */+ − UNUSED(hcryp);+ − + − /* NOTE : This function should not be modified; when the callback is needed,+ − the HAL_CRYP_OutCpltCallback can be implemented in the user file+ − */+ − }+ − + − /**+ − * @}+ − */+ − + − /** @defgroup CRYP_Exported_Functions_Group4 CRYP IRQ handler + − * @brief AES IRQ handler.+ − *+ − @verbatim + − ==============================================================================+ − ##### AES IRQ handler management #####+ − ============================================================================== + − [..] This section provides AES IRQ handler function.+ − + − @endverbatim+ − * @{+ − */+ − + − /**+ − * @brief Handle AES interrupt request.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − void HAL_CRYP_IRQHandler(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Check if error occurred */+ − if (__HAL_CRYP_GET_IT_SOURCE(CRYP_IT_ERRIE) != RESET)+ − {+ − /* If Write Error occurred */+ − if (__HAL_CRYP_GET_FLAG(CRYP_IT_WRERR) != RESET)+ − {+ − hcryp->ErrorCode |= HAL_CRYP_WRITE_ERROR;+ − hcryp->State = HAL_CRYP_STATE_ERROR;+ − }+ − /* If Read Error occurred */+ − if (__HAL_CRYP_GET_FLAG(CRYP_IT_RDERR) != RESET)+ − {+ − hcryp->ErrorCode |= HAL_CRYP_READ_ERROR;+ − hcryp->State = HAL_CRYP_STATE_ERROR;+ − }+ − + − /* If an error has been reported */+ − if (hcryp->State == HAL_CRYP_STATE_ERROR)+ − { + − /* Disable Error and Computation Complete Interrupts */+ − __HAL_CRYP_DISABLE_IT(CRYP_IT_CCFIE|CRYP_IT_ERRIE);+ − /* Clear all Interrupt flags */+ − __HAL_CRYP_CLEAR_FLAG(CRYP_ERR_CLEAR|CRYP_CCF_CLEAR);+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp); + − + − HAL_CRYP_ErrorCallback(hcryp);+ − + − return; + − }+ − }+ − + − /* Check if computation complete interrupt is enabled + − and if the computation complete flag is raised */+ − if((__HAL_CRYP_GET_FLAG(CRYP_IT_CCF) != RESET) && (__HAL_CRYP_GET_IT_SOURCE(CRYP_IT_CCFIE) != RESET))+ − { + − #if defined(AES_CR_NPBLB)+ − if ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC)+ − || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CCM_CMAC))+ − #else + − if ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC)+ − || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC))+ − #endif + − {+ − /* To ensure proper suspension requests management, CCF flag + − is reset in CRYP_AES_Auth_IT() according to the current + − phase under handling */+ − CRYP_AES_Auth_IT(hcryp);+ − }+ − else+ − {+ − /* Clear Computation Complete Flag */+ − __HAL_CRYP_CLEAR_FLAG(CRYP_CCF_CLEAR);+ − CRYP_AES_IT(hcryp);+ − }+ − }+ − }+ − + − /**+ − * @}+ − */+ − + − /** @defgroup CRYP_Exported_Functions_Group5 Peripheral State functions + − * @brief Peripheral State functions. + − *+ − @verbatim + − ==============================================================================+ − ##### Peripheral State functions #####+ − ============================================================================== + − [..]+ − This subsection permits to get in run-time the status of the peripheral.+ − + − @endverbatim+ − * @{+ − */+ − + − /**+ − * @brief Return the CRYP handle state.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval HAL state+ − */+ − HAL_CRYP_STATETypeDef HAL_CRYP_GetState(CRYP_HandleTypeDef *hcryp)+ − {+ − /* Return CRYP handle state */+ − return hcryp->State;+ − }+ − + − /**+ − * @brief Return the CRYP peripheral error.+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @note The returned error is a bit-map combination of possible errors + − * @retval Error bit-map+ − */+ − uint32_t HAL_CRYP_GetError(CRYP_HandleTypeDef *hcryp)+ − {+ − return hcryp->ErrorCode;+ − }+ − + − /**+ − * @}+ − */+ − + − /**+ − * @}+ − */+ − + − /** @addtogroup CRYP_Private_Functions+ − * @{+ − */+ − + − + − /**+ − * @brief Write the Key in KeyRx registers. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − static HAL_StatusTypeDef CRYP_SetKey(CRYP_HandleTypeDef *hcryp)+ − { + − uint32_t keyaddr = 0x0U;+ − + − if ((uint32_t)(hcryp->Init.pKey == NULL))+ − {+ − return HAL_ERROR;+ − }+ − + − + − keyaddr = (uint32_t)(hcryp->Init.pKey);+ − + − if (hcryp->Init.KeySize == CRYP_KEYSIZE_256B)+ − {+ − hcryp->Instance->KEYR7 = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->KEYR6 = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->KEYR5 = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->KEYR4 = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U; + − } + − + − hcryp->Instance->KEYR3 = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->KEYR2 = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->KEYR1 = __REV(*(uint32_t*)(keyaddr));+ − keyaddr+=4U;+ − hcryp->Instance->KEYR0 = __REV(*(uint32_t*)(keyaddr)); + − + − return HAL_OK;+ − }+ − + − /**+ − * @brief Write the InitVector/InitCounter in IVRx registers. + − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module+ − * @retval None+ − */+ − static HAL_StatusTypeDef CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp)+ − {+ − uint32_t ivaddr = 0x0U;+ − + − #if !defined(AES_CR_NPBLB)+ − if (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC)+ − {+ − hcryp->Instance->IVR3 = 0U;+ − hcryp->Instance->IVR2 = 0U;+ − hcryp->Instance->IVR1 = 0U; + − hcryp->Instance->IVR0 = 0U;+ − }+ − else+ − #endif+ − {+ − if (hcryp->Init.pInitVect == NULL)+ − {+ − return HAL_ERROR;+ − } + − + − ivaddr = (uint32_t)(hcryp->Init.pInitVect);+ − + − hcryp->Instance->IVR3 = __REV(*(uint32_t*)(ivaddr));+ − ivaddr+=4U;+ − hcryp->Instance->IVR2 = __REV(*(uint32_t*)(ivaddr));+ − ivaddr+=4U;+ − hcryp->Instance->IVR1 = __REV(*(uint32_t*)(ivaddr));+ − ivaddr+=4U;+ − hcryp->Instance->IVR0 = __REV(*(uint32_t*)(ivaddr));+ − }+ − return HAL_OK;+ − }+ − + − + − + − /** + − * @brief Handle CRYP block input/output data handling under interruption.+ − * @note The function is called under interruption only, once+ − * interruptions have been enabled by HAL_CRYPEx_AES_IT().+ − * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains+ − * the configuration information for CRYP module.+ − * @retval HAL status+ − */+ − static HAL_StatusTypeDef CRYP_AES_IT(CRYP_HandleTypeDef *hcryp)+ − {+ − uint32_t inputaddr = 0U;+ − uint32_t outputaddr = 0U; + − + − if(hcryp->State == HAL_CRYP_STATE_BUSY)+ − {+ − if (hcryp->Init.OperatingMode != CRYP_ALGOMODE_KEYDERIVATION)+ − {+ − /* Get the output data address */+ − outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;+ − + − /* Read the last available output block from the Data Output Register */+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUTR;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUTR;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUTR;+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = hcryp->Instance->DOUTR;+ − hcryp->pCrypOutBuffPtr += 16U;+ − hcryp->CrypOutCount -= 16U;+ − + − }+ − else+ − {+ − /* Read the derived key from the Key registers */+ − if (hcryp->Init.KeySize == CRYP_KEYSIZE_256B)+ − { + − *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR7);+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR6);+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR5);+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR4);+ − outputaddr+=4U;+ − }+ − + − *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR3);+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR2);+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR1);+ − outputaddr+=4U;+ − *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR0);+ − }+ − + − /* In case of ciphering or deciphering, check if all output text has been retrieved;+ − In case of key derivation, stop right there */+ − if ((hcryp->CrypOutCount == 0U) || (hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION))+ − {+ − /* Disable Computation Complete Flag and Errors Interrupts */+ − __HAL_CRYP_DISABLE_IT(CRYP_IT_CCFIE|CRYP_IT_ERRIE);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_READY;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − /* Call computation complete callback */+ − HAL_CRYPEx_ComputationCpltCallback(hcryp);+ − + − return HAL_OK;+ − }+ − /* If suspension flag has been raised, suspend processing */+ − else if (hcryp->SuspendRequest == HAL_CRYP_SUSPEND)+ − {+ − /* reset ModeSuspend */+ − hcryp->SuspendRequest = HAL_CRYP_SUSPEND_NONE;+ − + − /* Disable Computation Complete Flag and Errors Interrupts */+ − __HAL_CRYP_DISABLE_IT(CRYP_IT_CCFIE|CRYP_IT_ERRIE);+ − /* Change the CRYP state */+ − hcryp->State = HAL_CRYP_STATE_SUSPENDED;+ − + − /* Process Unlocked */+ − __HAL_UNLOCK(hcryp);+ − + − return HAL_OK;+ − }+ − else /* Process the rest of input data */+ − {+ − /* Get the Intput data address */+ − inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;+ − + − /* Increment/decrement instance pointer/counter */+ − hcryp->pCrypInBuffPtr += 16U;+ − hcryp->CrypInCount -= 16U;+ − + − /* Write the next input block in the Data Input register */+ − hcryp->Instance->DINR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DINR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DINR = *(uint32_t*)(inputaddr);+ − inputaddr+=4U;+ − hcryp->Instance->DINR = *(uint32_t*)(inputaddr);+ − + − return HAL_OK; + − }+ − }+ − else+ − {+ − return HAL_BUSY; + − }+ − }+ − + − /**+ − * @}+ − */+ − + − #endif /* AES */+ − + − #endif /* HAL_CRYP_MODULE_ENABLED */+ − + − /**+ − * @}+ − */+ − + − /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/+ −
