Mercurial > public > ostc4
view Common/Drivers/STM32F4xx_HAL_DRIVER_v120/Inc/stm32f4xx_hal_sd.h @ 114:79b19d56ab08 FlipDisplay
Eliminate warnings
| author | Ideenmodellierer |
|---|---|
| date | Thu, 03 Jan 2019 18:35:11 +0100 |
| parents | 5f11787b4f42 |
| children |
line wrap: on
line source
/** ****************************************************************************** * @file stm32f4xx_hal_sd.h * @author MCD Application Team * @version V1.2.0 * @date 26-December-2014 * @brief Header file of SD HAL module. ****************************************************************************** * @attention * * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef __STM32F4xx_HAL_SD_H #define __STM32F4xx_HAL_SD_H #ifdef __cplusplus extern "C" { #endif /* Includes ------------------------------------------------------------------*/ #include "stm32f4xx_ll_sdmmc.h" /** @addtogroup STM32F4xx_HAL_Driver * @{ */ /** @defgroup SD SD * @brief SD HAL module driver * @{ */ /* Exported types ------------------------------------------------------------*/ /** @defgroup SD_Exported_Types SD Exported Types * @{ */ /** @defgroup SD_Exported_Types_Group1 SD Handle Structure definition * @{ */ #define SD_InitTypeDef SDIO_InitTypeDef #define SD_TypeDef SDIO_TypeDef typedef struct { SD_TypeDef *Instance; /*!< SDIO register base address */ SD_InitTypeDef Init; /*!< SD required parameters */ HAL_LockTypeDef Lock; /*!< SD locking object */ uint32_t CardType; /*!< SD card type */ uint32_t RCA; /*!< SD relative card address */ uint32_t CSD[4]; /*!< SD card specific data table */ uint32_t CID[4]; /*!< SD card identification number table */ __IO uint32_t SdTransferCplt; /*!< SD transfer complete flag in non blocking mode */ __IO uint32_t SdTransferErr; /*!< SD transfer error flag in non blocking mode */ __IO uint32_t DmaTransferCplt; /*!< SD DMA transfer complete flag */ __IO uint32_t SdOperation; /*!< SD transfer operation (read/write) */ DMA_HandleTypeDef *hdmarx; /*!< SD Rx DMA handle parameters */ DMA_HandleTypeDef *hdmatx; /*!< SD Tx DMA handle parameters */ }SD_HandleTypeDef; /** * @} */ /** @defgroup SD_Exported_Types_Group2 Card Specific Data: CSD Register * @{ */ typedef struct { __IO uint8_t CSDStruct; /*!< CSD structure */ __IO uint8_t SysSpecVersion; /*!< System specification version */ __IO uint8_t Reserved1; /*!< Reserved */ __IO uint8_t TAAC; /*!< Data read access time 1 */ __IO uint8_t NSAC; /*!< Data read access time 2 in CLK cycles */ __IO uint8_t MaxBusClkFrec; /*!< Max. bus clock frequency */ __IO uint16_t CardComdClasses; /*!< Card command classes */ __IO uint8_t RdBlockLen; /*!< Max. read data block length */ __IO uint8_t PartBlockRead; /*!< Partial blocks for read allowed */ __IO uint8_t WrBlockMisalign; /*!< Write block misalignment */ __IO uint8_t RdBlockMisalign; /*!< Read block misalignment */ __IO uint8_t DSRImpl; /*!< DSR implemented */ __IO uint8_t Reserved2; /*!< Reserved */ __IO uint32_t DeviceSize; /*!< Device Size */ __IO uint8_t MaxRdCurrentVDDMin; /*!< Max. read current @ VDD min */ __IO uint8_t MaxRdCurrentVDDMax; /*!< Max. read current @ VDD max */ __IO uint8_t MaxWrCurrentVDDMin; /*!< Max. write current @ VDD min */ __IO uint8_t MaxWrCurrentVDDMax; /*!< Max. write current @ VDD max */ __IO uint8_t DeviceSizeMul; /*!< Device size multiplier */ __IO uint8_t EraseGrSize; /*!< Erase group size */ __IO uint8_t EraseGrMul; /*!< Erase group size multiplier */ __IO uint8_t WrProtectGrSize; /*!< Write protect group size */ __IO uint8_t WrProtectGrEnable; /*!< Write protect group enable */ __IO uint8_t ManDeflECC; /*!< Manufacturer default ECC */ __IO uint8_t WrSpeedFact; /*!< Write speed factor */ __IO uint8_t MaxWrBlockLen; /*!< Max. write data block length */ __IO uint8_t WriteBlockPaPartial; /*!< Partial blocks for write allowed */ __IO uint8_t Reserved3; /*!< Reserved */ __IO uint8_t ContentProtectAppli; /*!< Content protection application */ __IO uint8_t FileFormatGrouop; /*!< File format group */ __IO uint8_t CopyFlag; /*!< Copy flag (OTP) */ __IO uint8_t PermWrProtect; /*!< Permanent write protection */ __IO uint8_t TempWrProtect; /*!< Temporary write protection */ __IO uint8_t FileFormat; /*!< File format */ __IO uint8_t ECC; /*!< ECC code */ __IO uint8_t CSD_CRC; /*!< CSD CRC */ __IO uint8_t Reserved4; /*!< Always 1 */ }HAL_SD_CSDTypedef; /** * @} */ /** @defgroup SD_Exported_Types_Group3 Card Identification Data: CID Register * @{ */ typedef struct { __IO uint8_t ManufacturerID; /*!< Manufacturer ID */ __IO uint16_t OEM_AppliID; /*!< OEM/Application ID */ __IO uint32_t ProdName1; /*!< Product Name part1 */ __IO uint8_t ProdName2; /*!< Product Name part2 */ __IO uint8_t ProdRev; /*!< Product Revision */ __IO uint32_t ProdSN; /*!< Product Serial Number */ __IO uint8_t Reserved1; /*!< Reserved1 */ __IO uint16_t ManufactDate; /*!< Manufacturing Date */ __IO uint8_t CID_CRC; /*!< CID CRC */ __IO uint8_t Reserved2; /*!< Always 1 */ }HAL_SD_CIDTypedef; /** * @} */ /** @defgroup SD_Exported_Types_Group4 SD Card Status returned by ACMD13 * @{ */ typedef struct { __IO uint8_t DAT_BUS_WIDTH; /*!< Shows the currently defined data bus width */ __IO uint8_t SECURED_MODE; /*!< Card is in secured mode of operation */ __IO uint16_t SD_CARD_TYPE; /*!< Carries information about card type */ __IO uint32_t SIZE_OF_PROTECTED_AREA; /*!< Carries information about the capacity of protected area */ __IO uint8_t SPEED_CLASS; /*!< Carries information about the speed class of the card */ __IO uint8_t PERFORMANCE_MOVE; /*!< Carries information about the card's performance move */ __IO uint8_t AU_SIZE; /*!< Carries information about the card's allocation unit size */ __IO uint16_t ERASE_SIZE; /*!< Determines the number of AUs to be erased in one operation */ __IO uint8_t ERASE_TIMEOUT; /*!< Determines the timeout for any number of AU erase */ __IO uint8_t ERASE_OFFSET; /*!< Carries information about the erase offset */ }HAL_SD_CardStatusTypedef; /** * @} */ /** @defgroup SD_Exported_Types_Group5 SD Card information structure * @{ */ typedef struct { HAL_SD_CSDTypedef SD_csd; /*!< SD card specific data register */ HAL_SD_CIDTypedef SD_cid; /*!< SD card identification number register */ uint64_t CardCapacity; /*!< Card capacity */ uint32_t CardBlockSize; /*!< Card block size */ uint16_t RCA; /*!< SD relative card address */ uint8_t CardType; /*!< SD card type */ }HAL_SD_CardInfoTypedef; /** * @} */ /** @defgroup SD_Exported_Types_Group6 SD Error status enumeration Structure definition * @{ */ typedef enum { /** * @brief SD specific error defines */ SD_CMD_CRC_FAIL = (1), /*!< Command response received (but CRC check failed) */ SD_DATA_CRC_FAIL = (2), /*!< Data block sent/received (CRC check failed) */ SD_CMD_RSP_TIMEOUT = (3), /*!< Command response timeout */ SD_DATA_TIMEOUT = (4), /*!< Data timeout */ SD_TX_UNDERRUN = (5), /*!< Transmit FIFO underrun */ SD_RX_OVERRUN = (6), /*!< Receive FIFO overrun */ SD_START_BIT_ERR = (7), /*!< Start bit not detected on all data signals in wide bus mode */ SD_CMD_OUT_OF_RANGE = (8), /*!< Command's argument was out of range. */ SD_ADDR_MISALIGNED = (9), /*!< Misaligned address */ SD_BLOCK_LEN_ERR = (10), /*!< Transferred block length is not allowed for the card or the number of transferred bytes does not match the block length */ SD_ERASE_SEQ_ERR = (11), /*!< An error in the sequence of erase command occurs. */ SD_BAD_ERASE_PARAM = (12), /*!< An invalid selection for erase groups */ SD_WRITE_PROT_VIOLATION = (13), /*!< Attempt to program a write protect block */ SD_LOCK_UNLOCK_FAILED = (14), /*!< Sequence or password error has been detected in unlock command or if there was an attempt to access a locked card */ SD_COM_CRC_FAILED = (15), /*!< CRC check of the previous command failed */ SD_ILLEGAL_CMD = (16), /*!< Command is not legal for the card state */ SD_CARD_ECC_FAILED = (17), /*!< Card internal ECC was applied but failed to correct the data */ SD_CC_ERROR = (18), /*!< Internal card controller error */ SD_GENERAL_UNKNOWN_ERROR = (19), /*!< General or unknown error */ SD_STREAM_READ_UNDERRUN = (20), /*!< The card could not sustain data transfer in stream read operation. */ SD_STREAM_WRITE_OVERRUN = (21), /*!< The card could not sustain data programming in stream mode */ SD_CID_CSD_OVERWRITE = (22), /*!< CID/CSD overwrite error */ SD_WP_ERASE_SKIP = (23), /*!< Only partial address space was erased */ SD_CARD_ECC_DISABLED = (24), /*!< Command has been executed without using internal ECC */ SD_ERASE_RESET = (25), /*!< Erase sequence was cleared before executing because an out of erase sequence command was received */ SD_AKE_SEQ_ERROR = (26), /*!< Error in sequence of authentication. */ SD_INVALID_VOLTRANGE = (27), SD_ADDR_OUT_OF_RANGE = (28), SD_SWITCH_ERROR = (29), SD_SDIO_DISABLED = (30), SD_SDIO_FUNCTION_BUSY = (31), SD_SDIO_FUNCTION_FAILED = (32), SD_SDIO_UNKNOWN_FUNCTION = (33), /** * @brief Standard error defines */ SD_INTERNAL_ERROR = (34), SD_NOT_CONFIGURED = (35), SD_REQUEST_PENDING = (36), SD_REQUEST_NOT_APPLICABLE = (37), SD_INVALID_PARAMETER = (38), SD_UNSUPPORTED_FEATURE = (39), SD_UNSUPPORTED_HW = (40), SD_ERROR = (41), SD_OK = (0) }HAL_SD_ErrorTypedef; /** * @} */ /** @defgroup SD_Exported_Types_Group7 SD Transfer state enumeration structure * @{ */ typedef enum { SD_TRANSFER_OK = 0, /*!< Transfer success */ SD_TRANSFER_BUSY = 1, /*!< Transfer is occurring */ SD_TRANSFER_ERROR = 2 /*!< Transfer failed */ }HAL_SD_TransferStateTypedef; /** * @} */ /** @defgroup SD_Exported_Types_Group8 SD Card State enumeration structure * @{ */ typedef enum { SD_CARD_READY = ((uint32_t)0x00000001), /*!< Card state is ready */ SD_CARD_IDENTIFICATION = ((uint32_t)0x00000002), /*!< Card is in identification state */ SD_CARD_STANDBY = ((uint32_t)0x00000003), /*!< Card is in standby state */ SD_CARD_TRANSFER = ((uint32_t)0x00000004), /*!< Card is in transfer state */ SD_CARD_SENDING = ((uint32_t)0x00000005), /*!< Card is sending an operation */ SD_CARD_RECEIVING = ((uint32_t)0x00000006), /*!< Card is receiving operation information */ SD_CARD_PROGRAMMING = ((uint32_t)0x00000007), /*!< Card is in programming state */ SD_CARD_DISCONNECTED = ((uint32_t)0x00000008), /*!< Card is disconnected */ SD_CARD_ERROR = ((uint32_t)0x000000FF) /*!< Card is in error state */ }HAL_SD_CardStateTypedef; /** * @} */ /** @defgroup SD_Exported_Types_Group9 SD Operation enumeration structure * @{ */ typedef enum { SD_READ_SINGLE_BLOCK = 0, /*!< Read single block operation */ SD_READ_MULTIPLE_BLOCK = 1, /*!< Read multiple blocks operation */ SD_WRITE_SINGLE_BLOCK = 2, /*!< Write single block operation */ SD_WRITE_MULTIPLE_BLOCK = 3 /*!< Write multiple blocks operation */ }HAL_SD_OperationTypedef; /** * @} */ /** * @} */ /* Exported constants --------------------------------------------------------*/ /** @defgroup SD_Exported_Constants SD Exported Constants * @{ */ /** * @brief SD Commands Index */ #define SD_CMD_GO_IDLE_STATE ((uint8_t)0) /*!< Resets the SD memory card. */ #define SD_CMD_SEND_OP_COND ((uint8_t)1) /*!< Sends host capacity support information and activates the card's initialization process. */ #define SD_CMD_ALL_SEND_CID ((uint8_t)2) /*!< Asks any card connected to the host to send the CID numbers on the CMD line. */ #define SD_CMD_SET_REL_ADDR ((uint8_t)3) /*!< Asks the card to publish a new relative address (RCA). */ #define SD_CMD_SET_DSR ((uint8_t)4) /*!< Programs the DSR of all cards. */ #define SD_CMD_SDIO_SEN_OP_COND ((uint8_t)5) /*!< Sends host capacity support information (HCS) and asks the accessed card to send its operating condition register (OCR) content in the response on the CMD line. */ #define SD_CMD_HS_SWITCH ((uint8_t)6) /*!< Checks switchable function (mode 0) and switch card function (mode 1). */ #define SD_CMD_SEL_DESEL_CARD ((uint8_t)7) /*!< Selects the card by its own relative address and gets deselected by any other address */ #define SD_CMD_HS_SEND_EXT_CSD ((uint8_t)8) /*!< Sends SD Memory Card interface condition, which includes host supply voltage information and asks the card whether card supports voltage. */ #define SD_CMD_SEND_CSD ((uint8_t)9) /*!< Addressed card sends its card specific data (CSD) on the CMD line. */ #define SD_CMD_SEND_CID ((uint8_t)10) /*!< Addressed card sends its card identification (CID) on the CMD line. */ #define SD_CMD_READ_DAT_UNTIL_STOP ((uint8_t)11) /*!< SD card doesn't support it. */ #define SD_CMD_STOP_TRANSMISSION ((uint8_t)12) /*!< Forces the card to stop transmission. */ #define SD_CMD_SEND_STATUS ((uint8_t)13) /*!< Addressed card sends its status register. */ #define SD_CMD_HS_BUSTEST_READ ((uint8_t)14) #define SD_CMD_GO_INACTIVE_STATE ((uint8_t)15) /*!< Sends an addressed card into the inactive state. */ #define SD_CMD_SET_BLOCKLEN ((uint8_t)16) /*!< Sets the block length (in bytes for SDSC) for all following block commands (read, write, lock). Default block length is fixed to 512 Bytes. Not effective for SDHS and SDXC. */ #define SD_CMD_READ_SINGLE_BLOCK ((uint8_t)17) /*!< Reads single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of fixed 512 bytes in case of SDHC and SDXC. */ #define SD_CMD_READ_MULT_BLOCK ((uint8_t)18) /*!< Continuously transfers data blocks from card to host until interrupted by STOP_TRANSMISSION command. */ #define SD_CMD_HS_BUSTEST_WRITE ((uint8_t)19) /*!< 64 bytes tuning pattern is sent for SDR50 and SDR104. */ #define SD_CMD_WRITE_DAT_UNTIL_STOP ((uint8_t)20) /*!< Speed class control command. */ #define SD_CMD_SET_BLOCK_COUNT ((uint8_t)23) /*!< Specify block count for CMD18 and CMD25. */ #define SD_CMD_WRITE_SINGLE_BLOCK ((uint8_t)24) /*!< Writes single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of fixed 512 bytes in case of SDHC and SDXC. */ #define SD_CMD_WRITE_MULT_BLOCK ((uint8_t)25) /*!< Continuously writes blocks of data until a STOP_TRANSMISSION follows. */ #define SD_CMD_PROG_CID ((uint8_t)26) /*!< Reserved for manufacturers. */ #define SD_CMD_PROG_CSD ((uint8_t)27) /*!< Programming of the programmable bits of the CSD. */ #define SD_CMD_SET_WRITE_PROT ((uint8_t)28) /*!< Sets the write protection bit of the addressed group. */ #define SD_CMD_CLR_WRITE_PROT ((uint8_t)29) /*!< Clears the write protection bit of the addressed group. */ #define SD_CMD_SEND_WRITE_PROT ((uint8_t)30) /*!< Asks the card to send the status of the write protection bits. */ #define SD_CMD_SD_ERASE_GRP_START ((uint8_t)32) /*!< Sets the address of the first write block to be erased. (For SD card only). */ #define SD_CMD_SD_ERASE_GRP_END ((uint8_t)33) /*!< Sets the address of the last write block of the continuous range to be erased. */ #define SD_CMD_ERASE_GRP_START ((uint8_t)35) /*!< Sets the address of the first write block to be erased. Reserved for each command system set by switch function command (CMD6). */ #define SD_CMD_ERASE_GRP_END ((uint8_t)36) /*!< Sets the address of the last write block of the continuous range to be erased. Reserved for each command system set by switch function command (CMD6). */ #define SD_CMD_ERASE ((uint8_t)38) /*!< Reserved for SD security applications. */ #define SD_CMD_FAST_IO ((uint8_t)39) /*!< SD card doesn't support it (Reserved). */ #define SD_CMD_GO_IRQ_STATE ((uint8_t)40) /*!< SD card doesn't support it (Reserved). */ #define SD_CMD_LOCK_UNLOCK ((uint8_t)42) /*!< Sets/resets the password or lock/unlock the card. The size of the data block is set by the SET_BLOCK_LEN command. */ #define SD_CMD_APP_CMD ((uint8_t)55) /*!< Indicates to the card that the next command is an application specific command rather than a standard command. */ #define SD_CMD_GEN_CMD ((uint8_t)56) /*!< Used either to transfer a data block to the card or to get a data block from the card for general purpose/application specific commands. */ #define SD_CMD_NO_CMD ((uint8_t)64) /** * @brief Following commands are SD Card Specific commands. * SDIO_APP_CMD should be sent before sending these commands. */ #define SD_CMD_APP_SD_SET_BUSWIDTH ((uint8_t)6) /*!< (ACMD6) Defines the data bus width to be used for data transfer. The allowed data bus widths are given in SCR register. */ #define SD_CMD_SD_APP_STATUS ((uint8_t)13) /*!< (ACMD13) Sends the SD status. */ #define SD_CMD_SD_APP_SEND_NUM_WRITE_BLOCKS ((uint8_t)22) /*!< (ACMD22) Sends the number of the written (without errors) write blocks. Responds with 32bit+CRC data block. */ #define SD_CMD_SD_APP_OP_COND ((uint8_t)41) /*!< (ACMD41) Sends host capacity support information (HCS) and asks the accessed card to send its operating condition register (OCR) content in the response on the CMD line. */ #define SD_CMD_SD_APP_SET_CLR_CARD_DETECT ((uint8_t)42) /*!< (ACMD42) Connects/Disconnects the 50 KOhm pull-up resistor on CD/DAT3 (pin 1) of the card. */ #define SD_CMD_SD_APP_SEND_SCR ((uint8_t)51) /*!< Reads the SD Configuration Register (SCR). */ #define SD_CMD_SDIO_RW_DIRECT ((uint8_t)52) /*!< For SD I/O card only, reserved for security specification. */ #define SD_CMD_SDIO_RW_EXTENDED ((uint8_t)53) /*!< For SD I/O card only, reserved for security specification. */ /** * @brief Following commands are SD Card Specific security commands. * SD_CMD_APP_CMD should be sent before sending these commands. */ #define SD_CMD_SD_APP_GET_MKB ((uint8_t)43) /*!< For SD card only */ #define SD_CMD_SD_APP_GET_MID ((uint8_t)44) /*!< For SD card only */ #define SD_CMD_SD_APP_SET_CER_RN1 ((uint8_t)45) /*!< For SD card only */ #define SD_CMD_SD_APP_GET_CER_RN2 ((uint8_t)46) /*!< For SD card only */ #define SD_CMD_SD_APP_SET_CER_RES2 ((uint8_t)47) /*!< For SD card only */ #define SD_CMD_SD_APP_GET_CER_RES1 ((uint8_t)48) /*!< For SD card only */ #define SD_CMD_SD_APP_SECURE_READ_MULTIPLE_BLOCK ((uint8_t)18) /*!< For SD card only */ #define SD_CMD_SD_APP_SECURE_WRITE_MULTIPLE_BLOCK ((uint8_t)25) /*!< For SD card only */ #define SD_CMD_SD_APP_SECURE_ERASE ((uint8_t)38) /*!< For SD card only */ #define SD_CMD_SD_APP_CHANGE_SECURE_AREA ((uint8_t)49) /*!< For SD card only */ #define SD_CMD_SD_APP_SECURE_WRITE_MKB ((uint8_t)48) /*!< For SD card only */ /** * @brief Supported SD Memory Cards */ #define STD_CAPACITY_SD_CARD_V1_1 ((uint32_t)0x00000000) #define STD_CAPACITY_SD_CARD_V2_0 ((uint32_t)0x00000001) #define HIGH_CAPACITY_SD_CARD ((uint32_t)0x00000002) #define MULTIMEDIA_CARD ((uint32_t)0x00000003) #define SECURE_DIGITAL_IO_CARD ((uint32_t)0x00000004) #define HIGH_SPEED_MULTIMEDIA_CARD ((uint32_t)0x00000005) #define SECURE_DIGITAL_IO_COMBO_CARD ((uint32_t)0x00000006) #define HIGH_CAPACITY_MMC_CARD ((uint32_t)0x00000007) /** * @} */ /* Exported macro ------------------------------------------------------------*/ /** @defgroup SD_Exported_macros SD Exported Macros * @brief macros to handle interrupts and specific clock configurations * @{ */ /** * @brief Enable the SD device. * @retval None */ #define __HAL_SD_SDIO_ENABLE() __SDIO_ENABLE() /** * @brief Disable the SD device. * @retval None */ #define __HAL_SD_SDIO_DISABLE() __SDIO_DISABLE() /** * @brief Enable the SDIO DMA transfer. * @retval None */ #define __HAL_SD_SDIO_DMA_ENABLE() __SDIO_DMA_ENABLE() /** * @brief Disable the SDIO DMA transfer. * @retval None */ #define __HAL_SD_SDIO_DMA_DISABLE() __SDIO_DMA_DISABLE() /** * @brief Enable the SD device interrupt. * @param __HANDLE__: SD Handle * @param __INTERRUPT__: specifies the SDIO interrupt sources to be enabled. * This parameter can be one or a combination of the following values: * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt * @arg SDIO_IT_STBITERR: Start bit not detected on all data signals in wide * bus mode interrupt * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt * @arg SDIO_IT_TXACT: Data transmit in progress interrupt * @arg SDIO_IT_RXACT: Data receive in progress interrupt * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt * @arg SDIO_IT_CEATAEND: CE-ATA command completion signal received for CMD61 interrupt * @retval None */ #define __HAL_SD_SDIO_ENABLE_IT(__HANDLE__, __INTERRUPT__) __SDIO_ENABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__)) /** * @brief Disable the SD device interrupt. * @param __HANDLE__: SD Handle * @param __INTERRUPT__: specifies the SDIO interrupt sources to be disabled. * This parameter can be one or a combination of the following values: * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt * @arg SDIO_IT_STBITERR: Start bit not detected on all data signals in wide * bus mode interrupt * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt * @arg SDIO_IT_TXACT: Data transmit in progress interrupt * @arg SDIO_IT_RXACT: Data receive in progress interrupt * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt * @arg SDIO_IT_CEATAEND: CE-ATA command completion signal received for CMD61 interrupt * @retval None */ #define __HAL_SD_SDIO_DISABLE_IT(__HANDLE__, __INTERRUPT__) __SDIO_DISABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__)) /** * @brief Check whether the specified SD flag is set or not. * @param __HANDLE__: SD Handle * @param __FLAG__: specifies the flag to check. * This parameter can be one of the following values: * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed) * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed) * @arg SDIO_FLAG_CTIMEOUT: Command response timeout * @arg SDIO_FLAG_DTIMEOUT: Data timeout * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed) * @arg SDIO_FLAG_CMDSENT: Command sent (no response required) * @arg SDIO_FLAG_DATAEND: Data end (data counter, SDIDCOUNT, is zero) * @arg SDIO_FLAG_STBITERR: Start bit not detected on all data signals in wide bus mode. * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed) * @arg SDIO_FLAG_CMDACT: Command transfer in progress * @arg SDIO_FLAG_TXACT: Data transmit in progress * @arg SDIO_FLAG_RXACT: Data receive in progress * @arg SDIO_FLAG_TXFIFOHE: Transmit FIFO Half Empty * @arg SDIO_FLAG_RXFIFOHF: Receive FIFO Half Full * @arg SDIO_FLAG_TXFIFOF: Transmit FIFO full * @arg SDIO_FLAG_RXFIFOF: Receive FIFO full * @arg SDIO_FLAG_TXFIFOE: Transmit FIFO empty * @arg SDIO_FLAG_RXFIFOE: Receive FIFO empty * @arg SDIO_FLAG_TXDAVL: Data available in transmit FIFO * @arg SDIO_FLAG_RXDAVL: Data available in receive FIFO * @arg SDIO_FLAG_SDIOIT: SD I/O interrupt received * @arg SDIO_FLAG_CEATAEND: CE-ATA command completion signal received for CMD61 * @retval The new state of SD FLAG (SET or RESET). */ #define __HAL_SD_SDIO_GET_FLAG(__HANDLE__, __FLAG__) __SDIO_GET_FLAG((__HANDLE__)->Instance, (__FLAG__)) /** * @brief Clear the SD's pending flags. * @param __HANDLE__: SD Handle * @param __FLAG__: specifies the flag to clear. * This parameter can be one or a combination of the following values: * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed) * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed) * @arg SDIO_FLAG_CTIMEOUT: Command response timeout * @arg SDIO_FLAG_DTIMEOUT: Data timeout * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed) * @arg SDIO_FLAG_CMDSENT: Command sent (no response required) * @arg SDIO_FLAG_DATAEND: Data end (data counter, SDIDCOUNT, is zero) * @arg SDIO_FLAG_STBITERR: Start bit not detected on all data signals in wide bus mode * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed) * @arg SDIO_FLAG_SDIOIT: SD I/O interrupt received * @arg SDIO_FLAG_CEATAEND: CE-ATA command completion signal received for CMD61 * @retval None */ #define __HAL_SD_SDIO_CLEAR_FLAG(__HANDLE__, __FLAG__) __SDIO_CLEAR_FLAG((__HANDLE__)->Instance, (__FLAG__)) /** * @brief Check whether the specified SD interrupt has occurred or not. * @param __HANDLE__: SD Handle * @param __INTERRUPT__: specifies the SDIO interrupt source to check. * This parameter can be one of the following values: * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt * @arg SDIO_IT_STBITERR: Start bit not detected on all data signals in wide * bus mode interrupt * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt * @arg SDIO_IT_TXACT: Data transmit in progress interrupt * @arg SDIO_IT_RXACT: Data receive in progress interrupt * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt * @arg SDIO_IT_CEATAEND: CE-ATA command completion signal received for CMD61 interrupt * @retval The new state of SD IT (SET or RESET). */ #define __HAL_SD_SDIO_GET_IT (__HANDLE__, __INTERRUPT__) __SDIO_GET_IT ((__HANDLE__)->Instance, __INTERRUPT__) /** * @brief Clear the SD's interrupt pending bits. * @param __HANDLE__ : SD Handle * @param __INTERRUPT__: specifies the interrupt pending bit to clear. * This parameter can be one or a combination of the following values: * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt * @arg SDIO_IT_DATAEND: Data end (data counter, SDIO_DCOUNT, is zero) interrupt * @arg SDIO_IT_STBITERR: Start bit not detected on all data signals in wide * bus mode interrupt * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt * @arg SDIO_IT_CEATAEND: CE-ATA command completion signal received for CMD61 * @retval None */ #define __HAL_SD_SDIO_CLEAR_IT(__HANDLE__, __INTERRUPT__) __SDIO_CLEAR_IT((__HANDLE__)->Instance, (__INTERRUPT__)) /** * @} */ /* Exported functions --------------------------------------------------------*/ /** @defgroup SD_Exported_Functions SD Exported Functions * @{ */ /** @defgroup SD_Exported_Functions_Group1 Initialization and de-initialization functions * @{ */ HAL_SD_ErrorTypedef HAL_SD_Init(SD_HandleTypeDef *hsd, HAL_SD_CardInfoTypedef *SDCardInfo); HAL_StatusTypeDef HAL_SD_DeInit (SD_HandleTypeDef *hsd); void HAL_SD_MspInit(SD_HandleTypeDef *hsd); void HAL_SD_MspDeInit(SD_HandleTypeDef *hsd); /** * @} */ /** @defgroup SD_Exported_Functions_Group2 I/O operation functions * @{ */ /* Blocking mode: Polling */ HAL_SD_ErrorTypedef HAL_SD_ReadBlocks(SD_HandleTypeDef *hsd, uint32_t *pReadBuffer, uint64_t ReadAddr, uint32_t BlockSize, uint32_t NumberOfBlocks); HAL_SD_ErrorTypedef HAL_SD_WriteBlocks(SD_HandleTypeDef *hsd, uint32_t *pWriteBuffer, uint64_t WriteAddr, uint32_t BlockSize, uint32_t NumberOfBlocks); HAL_SD_ErrorTypedef HAL_SD_Erase(SD_HandleTypeDef *hsd, uint64_t startaddr, uint64_t endaddr); /* Non-Blocking mode: Interrupt */ void HAL_SD_IRQHandler(SD_HandleTypeDef *hsd); /* Callback in non blocking modes (DMA) */ void HAL_SD_DMA_RxCpltCallback(DMA_HandleTypeDef *hdma); void HAL_SD_DMA_RxErrorCallback(DMA_HandleTypeDef *hdma); void HAL_SD_DMA_TxCpltCallback(DMA_HandleTypeDef *hdma); void HAL_SD_DMA_TxErrorCallback(DMA_HandleTypeDef *hdma); void HAL_SD_XferCpltCallback(SD_HandleTypeDef *hsd); void HAL_SD_XferErrorCallback(SD_HandleTypeDef *hsd); /* Non-Blocking mode: DMA */ HAL_SD_ErrorTypedef HAL_SD_ReadBlocks_DMA(SD_HandleTypeDef *hsd, uint32_t *pReadBuffer, uint64_t ReadAddr, uint32_t BlockSize, uint32_t NumberOfBlocks); HAL_SD_ErrorTypedef HAL_SD_WriteBlocks_DMA(SD_HandleTypeDef *hsd, uint32_t *pWriteBuffer, uint64_t WriteAddr, uint32_t BlockSize, uint32_t NumberOfBlocks); HAL_SD_ErrorTypedef HAL_SD_CheckWriteOperation(SD_HandleTypeDef *hsd, uint32_t Timeout); HAL_SD_ErrorTypedef HAL_SD_CheckReadOperation(SD_HandleTypeDef *hsd, uint32_t Timeout); /** * @} */ /** @defgroup SD_Exported_Functions_Group3 Peripheral Control functions * @{ */ HAL_SD_ErrorTypedef HAL_SD_Get_CardInfo(SD_HandleTypeDef *hsd, HAL_SD_CardInfoTypedef *pCardInfo); HAL_SD_ErrorTypedef HAL_SD_WideBusOperation_Config(SD_HandleTypeDef *hsd, uint32_t WideMode); HAL_SD_ErrorTypedef HAL_SD_StopTransfer(SD_HandleTypeDef *hsd); HAL_SD_ErrorTypedef HAL_SD_HighSpeed (SD_HandleTypeDef *hsd); /** * @} */ /* Peripheral State functions ************************************************/ /** @defgroup SD_Exported_Functions_Group4 Peripheral State functions * @{ */ HAL_SD_ErrorTypedef HAL_SD_SendSDStatus(SD_HandleTypeDef *hsd, uint32_t *pSDstatus); HAL_SD_ErrorTypedef HAL_SD_GetCardStatus(SD_HandleTypeDef *hsd, HAL_SD_CardStatusTypedef *pCardStatus); HAL_SD_TransferStateTypedef HAL_SD_GetStatus(SD_HandleTypeDef *hsd); /** * @} */ /** * @} */ /* Private types -------------------------------------------------------------*/ /** @defgroup SD_Private_Types SD Private Types * @{ */ /** * @} */ /* Private defines -----------------------------------------------------------*/ /** @defgroup SD_Private_Defines SD Private Defines * @{ */ /** * @} */ /* Private variables ---------------------------------------------------------*/ /** @defgroup SD_Private_Variables SD Private Variables * @{ */ /** * @} */ /* Private constants ---------------------------------------------------------*/ /** @defgroup SD_Private_Constants SD Private Constants * @{ */ /** * @} */ /* Private macros ------------------------------------------------------------*/ /** @defgroup SD_Private_Macros SD Private Macros * @{ */ /** * @} */ /* Private functions prototypes ----------------------------------------------*/ /** @defgroup SD_Private_Functions_Prototypes SD Private Functions Prototypes * @{ */ /** * @} */ /* Private functions ---------------------------------------------------------*/ /** @defgroup SD_Private_Functions SD Private Functions * @{ */ /** * @} */ /** * @} */ /** * @} */ #ifdef __cplusplus } #endif #endif /* __STM32F4xx_HAL_SD_H */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/