Mercurial > public > ostc4
view Discovery/Inc/stm32f4xx_hal_conf.h @ 566:7761dd028386
add current build
author | heinrichsweikamp |
---|---|
date | Sat, 21 Nov 2020 17:41:59 +0100 |
parents | f35e53ef04e0 |
children | bc6c90e20d9e |
line wrap: on
line source
/////////////////////////////////////////////////////////////////////////////// /// -*- coding: UTF-8 -*- /// /// \file Discovery/Inc/stm32f4xx_hal_conf.h /// \brief The assert_param macro is used for function's parameters check. /// \author Heinrichs Weikamp /// \date 2018 /// /// $Id$ /////////////////////////////////////////////////////////////////////////////// /// \par Copyright (c) 2014-2018 Heinrichs Weikamp gmbh /// /// This program is free software: you can redistribute it and/or modify /// it under the terms of the GNU General Public License as published by /// the Free Software Foundation, either version 3 of the License, or /// (at your option) any later version. /// /// This program is distributed in the hope that it will be useful, /// but WITHOUT ANY WARRANTY; without even the implied warranty of /// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the /// GNU General Public License for more details. /// /// You should have received a copy of the GNU General Public License /// along with this program. If not, see <http://www.gnu.org/licenses/>. ////////////////////////////////////////////////////////////////////////////// /// \par COPYRIGHT(c) 2014 STMicroelectronics /// /// Redistribution and use in source and binary forms, with or without modification, /// are permitted provided that the following conditions are met: /// 1. Redistributions of source code must retain the above copyright notice, /// this list of conditions and the following disclaimer. /// 2. Redistributions in binary form must reproduce the above copyright notice, /// this list of conditions and the following disclaimer in the documentation /// and/or other materials provided with the distribution. /// 3. Neither the name of STMicroelectronics nor the names of its contributors /// may be used to endorse or promote products derived from this software /// without specific prior written permission. /// /// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" /// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE /// IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE /// DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE /// FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL /// DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR /// SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER /// CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, /// OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE /// OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ////////////////////////////////////////////////////////////////////////////// /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef STM32F4xx_HAL_CONF_H #define STM32F4xx_HAL_CONF_H /* Exported constants --------------------------------------------------------*/ /* ######################### Hardware Selection ############################## */ /* #define STM32F429xx definition is now done in preprocessor*/ /* ########################## Module Selection ############################## */ /** * @brief This is the list of modules to be used in the HAL driver */ #define HAL_MODULE_ENABLED //#define HAL_ADC_MODULE_ENABLED //#define HAL_CAN_MODULE_ENABLED //#define HAL_CRC_MODULE_ENABLED //#define HAL_CRYP_MODULE_ENABLED //#define HAL_DAC_MODULE_ENABLED //#define HAL_DCMI_MODULE_ENABLED //#define HAL_ETH_MODULE_ENABLED //#define HAL_NAND_MODULE_ENABLED //#define HAL_NOR_MODULE_ENABLED //#define HAL_PCCARD_MODULE_ENABLED //#define HAL_SRAM_MODULE_ENABLED //#define HAL_HASH_MODULE_ENABLED //#define HAL_I2C_MODULE_ENABLED //#define HAL_I2S_MODULE_ENABLED //#define HAL_IWDG_MODULE_ENABLED //#define HAL_RNG_MODULE_ENABLED //#define HAL_SAI_MODULE_ENABLED //#define HAL_SD_MODULE_ENABLED //#define HAL_USART_MODULE_ENABLED //#define HAL_IRDA_MODULE_ENABLED //#define HAL_SMARTCARD_MODULE_ENABLED //#define HAL_WWDG_MODULE_ENABLED //#define HAL_PCD_MODULE_ENABLED //#define HAL_HCD_MODULE_ENABLED #define HAL_SDRAM_MODULE_ENABLED #define HAL_GPIO_MODULE_ENABLED #define HAL_LTDC_MODULE_ENABLED #define HAL_DMA_MODULE_ENABLED #define HAL_DMA2D_MODULE_ENABLED #define HAL_RCC_MODULE_ENABLED #define HAL_RTC_MODULE_ENABLED #define HAL_SPI_MODULE_ENABLED #define HAL_TIM_MODULE_ENABLED #define HAL_UART_MODULE_ENABLED #define HAL_FLASH_MODULE_ENABLED #define HAL_PWR_MODULE_ENABLED #define HAL_CORTEX_MODULE_ENABLED /* ########################## HSE/HSI Values adaptation ##################### */ /** * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. * This value is used by the RCC HAL module to compute the system frequency * (when HSE is used as system clock source, directly or through the PLL). */ #if !defined (HSE_VALUE) #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */ #endif /* HSE_VALUE */ #if !defined (HSE_STARTUP_TIMEOUT) #define HSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for HSE start up, in ms */ #endif /* HSE_STARTUP_TIMEOUT */ /** * @brief Internal High Speed oscillator (HSI) value. * This value is used by the RCC HAL module to compute the system frequency * (when HSI is used as system clock source, directly or through the PLL). */ #if !defined (HSI_VALUE) #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ #endif /* HSI_VALUE */ /** * @brief Internal Low Speed oscillator (LSI) value. */ #if !defined (LSI_VALUE) #define LSI_VALUE ((uint32_t)40000U) #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz The real value may vary depending on the variations in voltage and temperature. */ /** * @brief External Low Speed oscillator (LSE) value. */ #if !defined (LSE_VALUE) #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */ #endif /* LSE_VALUE */ #if !defined (LSE_STARTUP_TIMEOUT) #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ #endif /* LSE_STARTUP_TIMEOUT */ /** * @brief External clock source for I2S peripheral * This value is used by the I2S HAL module to compute the I2S clock source * frequency, this source is inserted directly through I2S_CKIN pad. */ #if !defined (EXTERNAL_CLOCK_VALUE) #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the External audio frequency in Hz*/ #endif /* EXTERNAL_CLOCK_VALUE */ /* Tip: To avoid modifying this file each time you need to use different HSE, === you can define the HSE value in your toolchain compiler preprocessor. */ /* ########################### System Configuration ######################### */ /** * @brief This is the HAL system configuration section */ #define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ #define TICK_INT_PRIORITY ((uint32_t)0) /*!< tick interrupt priority */ #define USE_RTOS 0 #define PREFETCH_ENABLE 1 #define INSTRUCTION_CACHE_ENABLE 1 #define DATA_CACHE_ENABLE 1 /* ########################## Assert Selection ############################## */ /** * @brief Uncomment the line below to expanse the "assert_param" macro in the * HAL drivers code */ /* #define USE_FULL_ASSERT 1 */ /* ################## Ethernet peripheral configuration ##################### */ /* Section 1 : Ethernet peripheral configuration */ /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ #define MAC_ADDR0 2U #define MAC_ADDR1 0U #define MAC_ADDR2 0U #define MAC_ADDR3 0U #define MAC_ADDR4 0U #define MAC_ADDR5 0U /* Definition of the Ethernet driver buffers size and count */ #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ #define ETH_RXBUFNB ((uint32_t)4) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ #define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ /* Section 2: PHY configuration section */ /* DP83848 PHY Address*/ #define DP83848_PHY_ADDRESS 0x01U /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ #define PHY_RESET_DELAY ((uint32_t)0x000000FFU) /* PHY Configuration delay */ #define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFU) #define PHY_READ_TO ((uint32_t)0x0000FFFFU) #define PHY_WRITE_TO ((uint32_t)0x0000FFFFU) /* Section 3: Common PHY Registers */ #define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ #define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ #define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ #define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ #define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ #define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ #define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ #define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ /* Section 4: Extended PHY Registers */ #define PHY_SR ((uint16_t)0x0010) /*!< PHY status register Offset */ #define PHY_MICR ((uint16_t)0x0011) /*!< MII Interrupt Control Register */ #define PHY_MISR ((uint16_t)0x0012) /*!< MII Interrupt Status and Misc. Control Register */ #define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ #define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ #define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ #define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ #define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ #define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ #define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ /* Includes ------------------------------------------------------------------*/ /** * @brief Include module's header file */ #ifdef HAL_RCC_MODULE_ENABLED #include "stm32f4xx_hal_rcc.h" #endif /* HAL_RCC_MODULE_ENABLED */ #ifdef HAL_GPIO_MODULE_ENABLED #include "stm32f4xx_hal_gpio.h" #endif /* HAL_GPIO_MODULE_ENABLED */ #ifdef HAL_DMA_MODULE_ENABLED #include "stm32f4xx_hal_dma.h" #endif /* HAL_DMA_MODULE_ENABLED */ #ifdef HAL_CORTEX_MODULE_ENABLED #include "stm32f4xx_hal_cortex.h" #endif /* HAL_CORTEX_MODULE_ENABLED */ #ifdef HAL_ADC_MODULE_ENABLED #include "stm32f4xx_hal_adc.h" #endif /* HAL_ADC_MODULE_ENABLED */ #ifdef HAL_CAN_MODULE_ENABLED #include "stm32f4xx_hal_can.h" #endif /* HAL_CAN_MODULE_ENABLED */ #ifdef HAL_CRC_MODULE_ENABLED #include "stm32f4xx_hal_crc.h" #endif /* HAL_CRC_MODULE_ENABLED */ #ifdef HAL_CRYP_MODULE_ENABLED #include "stm32f4xx_hal_cryp.h" #endif /* HAL_CRYP_MODULE_ENABLED */ #ifdef HAL_DMA2D_MODULE_ENABLED #include "stm32f4xx_hal_dma2d.h" #endif /* HAL_DMA2D_MODULE_ENABLED */ #ifdef HAL_DAC_MODULE_ENABLED #include "stm32f4xx_hal_dac.h" #endif /* HAL_DAC_MODULE_ENABLED */ #ifdef HAL_DCMI_MODULE_ENABLED #include "stm32f4xx_hal_dcmi.h" #endif /* HAL_DCMI_MODULE_ENABLED */ #ifdef HAL_ETH_MODULE_ENABLED #include "stm32f4xx_hal_eth.h" #endif /* HAL_ETH_MODULE_ENABLED */ #ifdef HAL_FLASH_MODULE_ENABLED #include "stm32f4xx_hal_flash.h" #endif /* HAL_FLASH_MODULE_ENABLED */ #ifdef HAL_SRAM_MODULE_ENABLED #include "stm32f4xx_hal_sram.h" #endif /* HAL_SRAM_MODULE_ENABLED */ #ifdef HAL_NOR_MODULE_ENABLED #include "stm32f4xx_hal_nor.h" #endif /* HAL_NOR_MODULE_ENABLED */ #ifdef HAL_NAND_MODULE_ENABLED #include "stm32f4xx_hal_nand.h" #endif /* HAL_NAND_MODULE_ENABLED */ #ifdef HAL_PCCARD_MODULE_ENABLED #include "stm32f4xx_hal_pccard.h" #endif /* HAL_PCCARD_MODULE_ENABLED */ #ifdef HAL_SDRAM_MODULE_ENABLED #include "stm32f4xx_hal_sdram.h" #endif /* HAL_SDRAM_MODULE_ENABLED */ #ifdef HAL_HASH_MODULE_ENABLED #include "stm32f4xx_hal_hash.h" #endif /* HAL_HASH_MODULE_ENABLED */ #ifdef HAL_I2C_MODULE_ENABLED #include "stm32f4xx_hal_i2c.h" #endif /* HAL_I2C_MODULE_ENABLED */ #ifdef HAL_I2S_MODULE_ENABLED #include "stm32f4xx_hal_i2s.h" #endif /* HAL_I2S_MODULE_ENABLED */ #ifdef HAL_IWDG_MODULE_ENABLED #include "stm32f4xx_hal_iwdg.h" #endif /* HAL_IWDG_MODULE_ENABLED */ #ifdef HAL_LTDC_MODULE_ENABLED #include "stm32f4xx_hal_ltdc.h" #endif /* HAL_LTDC_MODULE_ENABLED */ #ifdef HAL_PWR_MODULE_ENABLED #include "stm32f4xx_hal_pwr.h" #endif /* HAL_PWR_MODULE_ENABLED */ #ifdef HAL_RNG_MODULE_ENABLED #include "stm32f4xx_hal_rng.h" #endif /* HAL_RNG_MODULE_ENABLED */ #ifdef HAL_RTC_MODULE_ENABLED #include "stm32f4xx_hal_rtc.h" #endif /* HAL_RTC_MODULE_ENABLED */ #ifdef HAL_SAI_MODULE_ENABLED #include "stm32f4xx_hal_sai.h" #endif /* HAL_SAI_MODULE_ENABLED */ #ifdef HAL_SD_MODULE_ENABLED #include "stm32f4xx_hal_sd.h" #endif /* HAL_SD_MODULE_ENABLED */ #ifdef HAL_SPI_MODULE_ENABLED #include "stm32f4xx_hal_spi.h" #endif /* HAL_SPI_MODULE_ENABLED */ #ifdef HAL_TIM_MODULE_ENABLED #include "stm32f4xx_hal_tim.h" #endif /* HAL_TIM_MODULE_ENABLED */ #ifdef HAL_UART_MODULE_ENABLED #include "stm32f4xx_hal_uart.h" #endif /* HAL_UART_MODULE_ENABLED */ #ifdef HAL_USART_MODULE_ENABLED #include "stm32f4xx_hal_usart.h" #endif /* HAL_USART_MODULE_ENABLED */ #ifdef HAL_IRDA_MODULE_ENABLED #include "stm32f4xx_hal_irda.h" #endif /* HAL_IRDA_MODULE_ENABLED */ #ifdef HAL_SMARTCARD_MODULE_ENABLED #include "stm32f4xx_hal_smartcard.h" #endif /* HAL_SMARTCARD_MODULE_ENABLED */ #ifdef HAL_WWDG_MODULE_ENABLED #include "stm32f4xx_hal_wwdg.h" #endif /* HAL_WWDG_MODULE_ENABLED */ #ifdef HAL_PCD_MODULE_ENABLED #include "stm32f4xx_hal_pcd.h" #endif /* HAL_PCD_MODULE_ENABLED */ #ifdef HAL_HCD_MODULE_ENABLED #include "stm32f4xx_hal_hcd.h" #endif /* HAL_HCD_MODULE_ENABLED */ /* Exported macro ------------------------------------------------------------*/ #ifdef USE_FULL_ASSERT /** * @brief The assert_param macro is used for function's parameters check. * @param expr: If expr is false, it calls assert_failed function * which reports the name of the source file and the source * line number of the call that failed. * If expr is true, it returns no value. * @retval None */ #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) /* Exported functions ------------------------------------------------------- */ void assert_failed(uint8_t* file, uint32_t line); #else #define assert_param(expr) ((void)0) #endif /* USE_FULL_ASSERT */ #endif /* STM32F4xx_HAL_CONF_H */