Mercurial > public > ostc4

view Small_CPU/Inc/batteryCharger.h @ 1007:65d35e66efb9 GasConsumption

Find changesets by keywords (author, files, the commit message), revision number or hash, or revset expression.
Improve compass calibration dialog: The previous calibration dialog showed some "magic" numbers and a 60 second count down. The new version is trying to guide the user through the calibration process: first rotate pitch, then roll and at last yaw angle. A step to the next angle is taken when enough data per angle is collected (change from red to green). To enable the yaw visualization a simple calibration is done while rotating the axis. The function behind the calibration was not modified => the suggested process can be ignored and the same handling as the with old dialog may be applied. With the new process the dialog may be left early. Anyhow it will still be left after 60 seconds and the fine calibration is performed in the same way as before.
author Ideenmodellierer
date Mon, 05 May 2025 21:02:34 +0200
parents d32901746950
children
line wrap: on
line source

/**
  ******************************************************************************
  * @file    batteryCharger.h
  * @author  heinrichs weikamp gmbh
  * @date    09-Dec-2014
  * @version V0.0.1
  * @since   09-Dec-2014
  * @brief	 LTC4054 Standalone Linear Li-Ion Battery Charger 
  *           
  @verbatim                 
  ============================================================================== 
                        ##### How to use #####
  ============================================================================== 
  @endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2015 heinrichs weikamp</center></h2>
  *
  ******************************************************************************
  */ 

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef BATTERY_CHARGER_H
#define BATTERY_CHARGER_H

#ifdef __cplusplus
 extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include <stdint.h>

#define CHARGE_IN_PIN				GPIO_PIN_2
#define CHARGE_IN_GPIO_PORT			GPIOC
#define CHARGE_IN_GPIO_ENABLE()		__GPIOC_CLK_ENABLE()

#define CHARGE_OUT_PIN				GPIO_PIN_1
#define CHARGE_OUT_GPIO_PORT		GPIOC
#define CHARGE_OUT_GPIO_ENABLE()	__GPIOC_CLK_ENABLE()

 typedef enum
 {
 	Charger_NotConnected = 0,		/* This is identified reading CHARGE_IN_PIN == HIGH */
 	Charger_WarmUp,					/* Charging started but counter did not yet reach a certain limit (used to debounce connect / disconnect events to avoid multiple increases of statistic charging cycle counter) */
 	Charger_Active,					/* Charging identified by  CHARGE_IN_PIN == LOW for a certain time */
 	Charger_Finished,
 	Charger_LostConnection,			/* Intermediate state to debounce disconnecting events (including charging error state like over temperature) */
 	Charger_ColdStart,				/* Cold start condition => check if an loaded battery has been inserted */
 	Charger_END
 } chargerState_t;


void init_battery_charger_status(void);
void set_charge_state(chargerState_t newState);
uint8_t get_charge_state(void);
void ReInit_battery_charger_status_pins(void);
void DeInit_battery_charger_status_pins(void);
void battery_charger_get_status_and_contral_battery_gas_gauge(uint8_t cycleTimeBase);

#ifdef __cplusplus
}
#endif

#endif /* BATTERY_CHARGER_H */

/************************ (C) COPYRIGHT heinrichs weikamp *****END OF FILE****/