view Small_CPU/Src/batteryCharger.c @ 290:5e0bb91d4a12 div-fixes-6

VPM, cleanup: 1st round Rather big cleanup. Removed numerous unused global variables, made almost all globals and functions static, removed unused code, removed commented core. No functional change in this commit. Signed-off-by: Jan Mulder <jlmulder@xs4all.nl>
author Jan Mulder <jlmulder@xs4all.nl>
date Thu, 02 May 2019 08:43:07 +0200
parents 5f11787b4f42
children 5149cd644fbc
line wrap: on
line source

/**
  ******************************************************************************
  * @file    batteryCharger.c 
  * @author  heinrichs weikamp gmbh
  * @date    09-Dec-2014
  * @version V0.0.1
  * @since   09-Dec-2014
  * @brief   LTC4054 Battery Charger
  *           
  @verbatim                 
  ============================================================================== 
                        ##### How to use #####
  ============================================================================== 

The bq5105x provides one status output, CHG. This output is an open-drain NMOS device that is rated to 20 V.
The open-drain FET connected to the CHG pin will be turned on whenever the output (BAT) of the charger is
enabled. As a note, the output of the charger supply will not be enabled if the VRECT-REG does not converge to the
no-load target voltage.

CHG F4 7 O Open-drain output – active when BAT is enabled. Float if not used.

@endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2015 heinrichs weikamp</center></h2>
  *
  ******************************************************************************
  */ 
/* Includes ------------------------------------------------------------------*/
#include "batteryCharger.h"
#include "batteryGasGauge.h"
#include "stm32f4xx_hal.h"
#include "scheduler.h"


#define CHARGE_IN_PIN							GPIO_PIN_2
#define CHARGE_IN_GPIO_PORT				GPIOC
#define CHARGE_IN_GPIO_ENABLE()		__GPIOC_CLK_ENABLE()

#define CHARGE_OUT_PIN						GPIO_PIN_1
#define CHARGE_OUT_GPIO_PORT			GPIOC
#define CHARGE_OUT_GPIO_ENABLE()	__GPIOC_CLK_ENABLE()


uint8_t battery_i_charge_status = 0;
uint8_t battery_charger_counter = 0;

/* can be 0, 1 or 255
 * 0 is disconnected
 * 1 is charging
 * 255 is full
 */
uint8_t get_charge_status(void)
{
	return battery_i_charge_status;
}

void init_battery_charger_status(void)
{
	#ifdef OSTC_ON_DISCOVERY_HARDWARE
		return;
	#endif

  CHARGE_IN_GPIO_ENABLE();
  CHARGE_OUT_GPIO_ENABLE();
	
	ReInit_battery_charger_status_pins();
}

void ReInit_battery_charger_status_pins(void)
{
	#ifdef OSTC_ON_DISCOVERY_HARDWARE
		return;
	#endif

  GPIO_InitTypeDef   GPIO_InitStructure;

  GPIO_InitStructure.Pin = CHARGE_IN_PIN;
  GPIO_InitStructure.Mode = GPIO_MODE_INPUT;
  GPIO_InitStructure.Pull = GPIO_NOPULL;
  GPIO_InitStructure.Speed = GPIO_SPEED_LOW;
  HAL_GPIO_Init(CHARGE_IN_GPIO_PORT, &GPIO_InitStructure); 

  GPIO_InitStructure.Pin = CHARGE_OUT_PIN;
  GPIO_InitStructure.Mode = GPIO_MODE_ANALOG;
  GPIO_InitStructure.Pull = GPIO_NOPULL;
  GPIO_InitStructure.Speed = GPIO_SPEED_LOW;
  HAL_GPIO_Init(CHARGE_OUT_GPIO_PORT, &GPIO_InitStructure); 
}


void DeInit_battery_charger_status_pins(void)
{
	#ifdef OSTC_ON_DISCOVERY_HARDWARE
		return;
	#endif
  GPIO_InitTypeDef   GPIO_InitStructure;


	GPIO_InitStructure.Mode = GPIO_MODE_ANALOG;
  GPIO_InitStructure.Speed = GPIO_SPEED_LOW;
  GPIO_InitStructure.Pull = GPIO_NOPULL;

  GPIO_InitStructure.Pin = CHARGE_IN_PIN;
  HAL_GPIO_Init(CHARGE_IN_GPIO_PORT, &GPIO_InitStructure); 

  GPIO_InitStructure.Pin = CHARGE_OUT_PIN;
  HAL_GPIO_Init(CHARGE_OUT_GPIO_PORT, &GPIO_InitStructure); 
}

/* static counter is used to avoid multiple counts of charge startings
	 and after that it is used, starting at 127 to count for the charge full signal

	there a short disconnections with the QI charger
	therefore the battery_charger_counter has a countdown instead of = 0.

	battery_gas_gauge_set_charge_full and  scheduleUpdateDeviceDataChargerFull are
	set after disconnection as the charging process continues as long as not disconnected
  to prevent the short disconnections the battery_charger_counter is used too including
	upcounting again while battery_i_charge_status == 255 and the connection is established

 */

void battery_charger_get_status_and_contral_battery_gas_gauge(uint8_t inSleepModeLessCounts)
{
	#ifdef OSTC_ON_DISCOVERY_HARDWARE
		return;
	#endif
	
	/* on disconnection or while disconnected */
	if(HAL_GPIO_ReadPin(CHARGE_IN_GPIO_PORT,CHARGE_IN_PIN))
	{
		if(battery_charger_counter)
		{
			battery_charger_counter--;
			global.dataSendToMaster.chargeStatus = CHARGER_lostConnection;
			global.deviceDataSendToMaster.chargeStatus = CHARGER_lostConnection;
		}
		/* max count down to 127+5 or 127+20 */
		if((battery_i_charge_status == 255) && battery_charger_counter < 127)
		{
//			battery_gas_gauge_set_charge_full();
//			scheduleUpdateDeviceDataChargerFull();
			battery_charger_counter = 0;
		}
		
		if(battery_charger_counter == 0)
		{
			battery_i_charge_status = 0;
			global.dataSendToMaster.chargeStatus = CHARGER_off;
			global.deviceDataSendToMaster.chargeStatus = CHARGER_off;

		}
		return;
	}

	/* connected */
	
	/* wait for disconnection to write and reset */
	if(battery_i_charge_status == 255)
	{
		global.dataSendToMaster.chargeStatus = CHARGER_complete;
		global.deviceDataSendToMaster.chargeStatus = CHARGER_complete;
		
		if((inSleepModeLessCounts && (battery_charger_counter < 127+5)) || (battery_charger_counter < 127+20))
		battery_charger_counter++;
		return;
	}

	if(battery_charger_counter == 0)
		battery_i_charge_status = 1;

	/* charger is connected and didn't signal full yet */
	global.dataSendToMaster.chargeStatus = CHARGER_running;
	global.deviceDataSendToMaster.chargeStatus = CHARGER_running;

	GPIO_InitTypeDef   GPIO_InitStructure;
  GPIO_InitStructure.Pin = CHARGE_OUT_PIN;
  GPIO_InitStructure.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStructure.Pull = GPIO_NOPULL;
  GPIO_InitStructure.Speed = GPIO_SPEED_LOW;
  HAL_GPIO_Init(CHARGE_OUT_GPIO_PORT, &GPIO_InitStructure); 
	HAL_GPIO_WritePin(CHARGE_OUT_GPIO_PORT, CHARGE_OUT_PIN,GPIO_PIN_SET);
	HAL_Delay(1);

	
	if(battery_charger_counter < 120)
	{
		if(!inSleepModeLessCounts)
			battery_charger_counter++;
		else
		{
			battery_charger_counter += 30;
			if(battery_charger_counter >= 127)
				battery_charger_counter = 126;
		}
	}
	else
	if(battery_charger_counter < 127)
	{
		battery_charger_counter = 127;
		if(battery_i_charge_status < 2)
		{
			battery_i_charge_status = 2;
			scheduleUpdateDeviceDataChargerCharging();
		}
	}

	if(battery_charger_counter >= 127)
	{
		if(HAL_GPIO_ReadPin(CHARGE_IN_GPIO_PORT,CHARGE_IN_PIN) || (get_voltage() >= 4.1f))
		{
			battery_charger_counter++;
			if((inSleepModeLessCounts && (battery_charger_counter > 127+5)) || (battery_charger_counter > 127+20))
			{
				battery_charger_counter = 127;
				if(get_voltage() >= 4.1f)
				{
					battery_i_charge_status = 255;
					battery_gas_gauge_set_charge_full();
					scheduleUpdateDeviceDataChargerFull();
				}					
			}
		}
		else
			battery_charger_counter = 127;
	}

  GPIO_InitStructure.Pin = CHARGE_OUT_PIN;
  GPIO_InitStructure.Mode = GPIO_MODE_ANALOG;
  GPIO_InitStructure.Pull = GPIO_NOPULL;
  GPIO_InitStructure.Speed = GPIO_SPEED_LOW;
  HAL_GPIO_Init(CHARGE_OUT_GPIO_PORT, &GPIO_InitStructure); 
}

/************************ (C) COPYRIGHT heinrichs weikamp *****END OF FILE****/