Mercurial > public > ostc4
view Common/Drivers/STM32F4xx/Source/Templates/system_stm32f4xx.c @ 406:439874690f85 Improment_NVM
Bugfix Min max values for device data checks:
Devicedata was set to it lower limit in case of a lower invalid value and upper limit in case a bigger value was detected. This could cause the history memory to be set to a min / max limit and never beeing updated again => Implemented a selection to specify which limit shall be used as default.
Minor change: "header" was used as global as well as as local variable => changed name for global variant to gheader.
Operation hours were not updated =>adde check for opeartion hours
author | ideenmodellierer |
---|---|
date | Sun, 12 Jan 2020 17:57:11 +0100 |
parents | c78bcbd5deda |
children |
line wrap: on
line source
/** ****************************************************************************** * @file system_stm32f4xx.c * @author MCD Application Team * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File. * * This file provides two functions and one global variable to be called from * user application: * - SystemInit(): This function is called at startup just after reset and * before branch to main program. This call is made inside * the "startup_stm32f4xx.s" file. * * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used * by the user application to setup the SysTick * timer or configure other parameters. * * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must * be called whenever the core clock is changed * during program execution. * * ****************************************************************************** * @attention * * <h2><center>© COPYRIGHT 2017 STMicroelectronics</center></h2> * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /** @addtogroup CMSIS * @{ */ /** @addtogroup stm32f4xx_system * @{ */ /** @addtogroup STM32F4xx_System_Private_Includes * @{ */ #include "stm32f4xx.h" #if !defined (HSE_VALUE) #define HSE_VALUE ((uint32_t)25000000) /*!< Default value of the External oscillator in Hz */ #endif /* HSE_VALUE */ #if !defined (HSI_VALUE) #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/ #endif /* HSI_VALUE */ /** * @} */ /** @addtogroup STM32F4xx_System_Private_TypesDefinitions * @{ */ /** * @} */ /** @addtogroup STM32F4xx_System_Private_Defines * @{ */ /************************* Miscellaneous Configuration ************************/ /*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */ #if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\ || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\ || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) /* #define DATA_IN_ExtSRAM */ #endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\ STM32F412Zx || STM32F412Vx */ #if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\ || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) /* #define DATA_IN_ExtSDRAM */ #endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\ STM32F479xx */ /*!< Uncomment the following line if you need to relocate your vector Table in Internal SRAM. */ /* #define VECT_TAB_SRAM */ #define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field. This value must be a multiple of 0x200. */ /******************************************************************************/ /** * @} */ /** @addtogroup STM32F4xx_System_Private_Macros * @{ */ /** * @} */ /** @addtogroup STM32F4xx_System_Private_Variables * @{ */ /* This variable is updated in three ways: 1) by calling CMSIS function SystemCoreClockUpdate() 2) by calling HAL API function HAL_RCC_GetHCLKFreq() 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency Note: If you use this function to configure the system clock; then there is no need to call the 2 first functions listed above, since SystemCoreClock variable is updated automatically. */ uint32_t SystemCoreClock = 16000000; const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4}; /** * @} */ /** @addtogroup STM32F4xx_System_Private_FunctionPrototypes * @{ */ #if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM) static void SystemInit_ExtMemCtl(void); #endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */ /** * @} */ /** @addtogroup STM32F4xx_System_Private_Functions * @{ */ /** * @brief Setup the microcontroller system * Initialize the FPU setting, vector table location and External memory * configuration. * @param None * @retval None */ void SystemInit(void) { /* FPU settings ------------------------------------------------------------*/ #if (__FPU_PRESENT == 1) && (__FPU_USED == 1) SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */ #endif /* Reset the RCC clock configuration to the default reset state ------------*/ /* Set HSION bit */ RCC->CR |= (uint32_t)0x00000001; /* Reset CFGR register */ RCC->CFGR = 0x00000000; /* Reset HSEON, CSSON and PLLON bits */ RCC->CR &= (uint32_t)0xFEF6FFFF; /* Reset PLLCFGR register */ RCC->PLLCFGR = 0x24003010; /* Reset HSEBYP bit */ RCC->CR &= (uint32_t)0xFFFBFFFF; /* Disable all interrupts */ RCC->CIR = 0x00000000; #if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM) SystemInit_ExtMemCtl(); #endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */ /* Configure the Vector Table location add offset address ------------------*/ #ifdef VECT_TAB_SRAM SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */ #else SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */ #endif } /** * @brief Update SystemCoreClock variable according to Clock Register Values. * The SystemCoreClock variable contains the core clock (HCLK), it can * be used by the user application to setup the SysTick timer or configure * other parameters. * * @note Each time the core clock (HCLK) changes, this function must be called * to update SystemCoreClock variable value. Otherwise, any configuration * based on this variable will be incorrect. * * @note - The system frequency computed by this function is not the real * frequency in the chip. It is calculated based on the predefined * constant and the selected clock source: * * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*) * * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**) * * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) * or HSI_VALUE(*) multiplied/divided by the PLL factors. * * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value * 16 MHz) but the real value may vary depending on the variations * in voltage and temperature. * * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value * depends on the application requirements), user has to ensure that HSE_VALUE * is same as the real frequency of the crystal used. Otherwise, this function * may have wrong result. * * - The result of this function could be not correct when using fractional * value for HSE crystal. * * @param None * @retval None */ void SystemCoreClockUpdate(void) { uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2; /* Get SYSCLK source -------------------------------------------------------*/ tmp = RCC->CFGR & RCC_CFGR_SWS; switch (tmp) { case 0x00: /* HSI used as system clock source */ SystemCoreClock = HSI_VALUE; break; case 0x04: /* HSE used as system clock source */ SystemCoreClock = HSE_VALUE; break; case 0x08: /* PLL used as system clock source */ /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N SYSCLK = PLL_VCO / PLL_P */ pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22; pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM; if (pllsource != 0) { /* HSE used as PLL clock source */ pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6); } else { /* HSI used as PLL clock source */ pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6); } pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2; SystemCoreClock = pllvco/pllp; break; default: SystemCoreClock = HSI_VALUE; break; } /* Compute HCLK frequency --------------------------------------------------*/ /* Get HCLK prescaler */ tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)]; /* HCLK frequency */ SystemCoreClock >>= tmp; } #if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM) #if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\ || defined(STM32F469xx) || defined(STM32F479xx) /** * @brief Setup the external memory controller. * Called in startup_stm32f4xx.s before jump to main. * This function configures the external memories (SRAM/SDRAM) * This SRAM/SDRAM will be used as program data memory (including heap and stack). * @param None * @retval None */ void SystemInit_ExtMemCtl(void) { __IO uint32_t tmp = 0x00; register uint32_t tmpreg = 0, timeout = 0xFFFF; register __IO uint32_t index; /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */ RCC->AHB1ENR |= 0x000001F8; /* Delay after an RCC peripheral clock enabling */ tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN); /* Connect PDx pins to FMC Alternate function */ GPIOD->AFR[0] = 0x00CCC0CC; GPIOD->AFR[1] = 0xCCCCCCCC; /* Configure PDx pins in Alternate function mode */ GPIOD->MODER = 0xAAAA0A8A; /* Configure PDx pins speed to 100 MHz */ GPIOD->OSPEEDR = 0xFFFF0FCF; /* Configure PDx pins Output type to push-pull */ GPIOD->OTYPER = 0x00000000; /* No pull-up, pull-down for PDx pins */ GPIOD->PUPDR = 0x00000000; /* Connect PEx pins to FMC Alternate function */ GPIOE->AFR[0] = 0xC00CC0CC; GPIOE->AFR[1] = 0xCCCCCCCC; /* Configure PEx pins in Alternate function mode */ GPIOE->MODER = 0xAAAA828A; /* Configure PEx pins speed to 100 MHz */ GPIOE->OSPEEDR = 0xFFFFC3CF; /* Configure PEx pins Output type to push-pull */ GPIOE->OTYPER = 0x00000000; /* No pull-up, pull-down for PEx pins */ GPIOE->PUPDR = 0x00000000; /* Connect PFx pins to FMC Alternate function */ GPIOF->AFR[0] = 0xCCCCCCCC; GPIOF->AFR[1] = 0xCCCCCCCC; /* Configure PFx pins in Alternate function mode */ GPIOF->MODER = 0xAA800AAA; /* Configure PFx pins speed to 50 MHz */ GPIOF->OSPEEDR = 0xAA800AAA; /* Configure PFx pins Output type to push-pull */ GPIOF->OTYPER = 0x00000000; /* No pull-up, pull-down for PFx pins */ GPIOF->PUPDR = 0x00000000; /* Connect PGx pins to FMC Alternate function */ GPIOG->AFR[0] = 0xCCCCCCCC; GPIOG->AFR[1] = 0xCCCCCCCC; /* Configure PGx pins in Alternate function mode */ GPIOG->MODER = 0xAAAAAAAA; /* Configure PGx pins speed to 50 MHz */ GPIOG->OSPEEDR = 0xAAAAAAAA; /* Configure PGx pins Output type to push-pull */ GPIOG->OTYPER = 0x00000000; /* No pull-up, pull-down for PGx pins */ GPIOG->PUPDR = 0x00000000; /* Connect PHx pins to FMC Alternate function */ GPIOH->AFR[0] = 0x00C0CC00; GPIOH->AFR[1] = 0xCCCCCCCC; /* Configure PHx pins in Alternate function mode */ GPIOH->MODER = 0xAAAA08A0; /* Configure PHx pins speed to 50 MHz */ GPIOH->OSPEEDR = 0xAAAA08A0; /* Configure PHx pins Output type to push-pull */ GPIOH->OTYPER = 0x00000000; /* No pull-up, pull-down for PHx pins */ GPIOH->PUPDR = 0x00000000; /* Connect PIx pins to FMC Alternate function */ GPIOI->AFR[0] = 0xCCCCCCCC; GPIOI->AFR[1] = 0x00000CC0; /* Configure PIx pins in Alternate function mode */ GPIOI->MODER = 0x0028AAAA; /* Configure PIx pins speed to 50 MHz */ GPIOI->OSPEEDR = 0x0028AAAA; /* Configure PIx pins Output type to push-pull */ GPIOI->OTYPER = 0x00000000; /* No pull-up, pull-down for PIx pins */ GPIOI->PUPDR = 0x00000000; /*-- FMC Configuration -------------------------------------------------------*/ /* Enable the FMC interface clock */ RCC->AHB3ENR |= 0x00000001; /* Delay after an RCC peripheral clock enabling */ tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN); FMC_Bank5_6->SDCR[0] = 0x000019E4; FMC_Bank5_6->SDTR[0] = 0x01115351; /* SDRAM initialization sequence */ /* Clock enable command */ FMC_Bank5_6->SDCMR = 0x00000011; tmpreg = FMC_Bank5_6->SDSR & 0x00000020; while((tmpreg != 0) && (timeout-- > 0)) { tmpreg = FMC_Bank5_6->SDSR & 0x00000020; } /* Delay */ for (index = 0; index<1000; index++); /* PALL command */ FMC_Bank5_6->SDCMR = 0x00000012; timeout = 0xFFFF; while((tmpreg != 0) && (timeout-- > 0)) { tmpreg = FMC_Bank5_6->SDSR & 0x00000020; } /* Auto refresh command */ FMC_Bank5_6->SDCMR = 0x00000073; timeout = 0xFFFF; while((tmpreg != 0) && (timeout-- > 0)) { tmpreg = FMC_Bank5_6->SDSR & 0x00000020; } /* MRD register program */ FMC_Bank5_6->SDCMR = 0x00046014; timeout = 0xFFFF; while((tmpreg != 0) && (timeout-- > 0)) { tmpreg = FMC_Bank5_6->SDSR & 0x00000020; } /* Set refresh count */ tmpreg = FMC_Bank5_6->SDRTR; FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1)); /* Disable write protection */ tmpreg = FMC_Bank5_6->SDCR[0]; FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF); #if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) /* Configure and enable Bank1_SRAM2 */ FMC_Bank1->BTCR[2] = 0x00001011; FMC_Bank1->BTCR[3] = 0x00000201; FMC_Bank1E->BWTR[2] = 0x0fffffff; #endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */ #if defined(STM32F469xx) || defined(STM32F479xx) /* Configure and enable Bank1_SRAM2 */ FMC_Bank1->BTCR[2] = 0x00001091; FMC_Bank1->BTCR[3] = 0x00110212; FMC_Bank1E->BWTR[2] = 0x0fffffff; #endif /* STM32F469xx || STM32F479xx */ (void)(tmp); } #endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ #elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM) /** * @brief Setup the external memory controller. * Called in startup_stm32f4xx.s before jump to main. * This function configures the external memories (SRAM/SDRAM) * This SRAM/SDRAM will be used as program data memory (including heap and stack). * @param None * @retval None */ void SystemInit_ExtMemCtl(void) { __IO uint32_t tmp = 0x00; #if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\ || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx) #if defined (DATA_IN_ExtSDRAM) register uint32_t tmpreg = 0, timeout = 0xFFFF; register __IO uint32_t index; #if defined(STM32F446xx) /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface clock */ RCC->AHB1ENR |= 0x0000007D; #else /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */ RCC->AHB1ENR |= 0x000001F8; #endif /* STM32F446xx */ /* Delay after an RCC peripheral clock enabling */ tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN); #if defined(STM32F446xx) /* Connect PAx pins to FMC Alternate function */ GPIOA->AFR[0] |= 0xC0000000; GPIOA->AFR[1] |= 0x00000000; /* Configure PDx pins in Alternate function mode */ GPIOA->MODER |= 0x00008000; /* Configure PDx pins speed to 50 MHz */ GPIOA->OSPEEDR |= 0x00008000; /* Configure PDx pins Output type to push-pull */ GPIOA->OTYPER |= 0x00000000; /* No pull-up, pull-down for PDx pins */ GPIOA->PUPDR |= 0x00000000; /* Connect PCx pins to FMC Alternate function */ GPIOC->AFR[0] |= 0x00CC0000; GPIOC->AFR[1] |= 0x00000000; /* Configure PDx pins in Alternate function mode */ GPIOC->MODER |= 0x00000A00; /* Configure PDx pins speed to 50 MHz */ GPIOC->OSPEEDR |= 0x00000A00; /* Configure PDx pins Output type to push-pull */ GPIOC->OTYPER |= 0x00000000; /* No pull-up, pull-down for PDx pins */ GPIOC->PUPDR |= 0x00000000; #endif /* STM32F446xx */ /* Connect PDx pins to FMC Alternate function */ GPIOD->AFR[0] = 0x000000CC; GPIOD->AFR[1] = 0xCC000CCC; /* Configure PDx pins in Alternate function mode */ GPIOD->MODER = 0xA02A000A; /* Configure PDx pins speed to 50 MHz */ GPIOD->OSPEEDR = 0xA02A000A; /* Configure PDx pins Output type to push-pull */ GPIOD->OTYPER = 0x00000000; /* No pull-up, pull-down for PDx pins */ GPIOD->PUPDR = 0x00000000; /* Connect PEx pins to FMC Alternate function */ GPIOE->AFR[0] = 0xC00000CC; GPIOE->AFR[1] = 0xCCCCCCCC; /* Configure PEx pins in Alternate function mode */ GPIOE->MODER = 0xAAAA800A; /* Configure PEx pins speed to 50 MHz */ GPIOE->OSPEEDR = 0xAAAA800A; /* Configure PEx pins Output type to push-pull */ GPIOE->OTYPER = 0x00000000; /* No pull-up, pull-down for PEx pins */ GPIOE->PUPDR = 0x00000000; /* Connect PFx pins to FMC Alternate function */ GPIOF->AFR[0] = 0xCCCCCCCC; GPIOF->AFR[1] = 0xCCCCCCCC; /* Configure PFx pins in Alternate function mode */ GPIOF->MODER = 0xAA800AAA; /* Configure PFx pins speed to 50 MHz */ GPIOF->OSPEEDR = 0xAA800AAA; /* Configure PFx pins Output type to push-pull */ GPIOF->OTYPER = 0x00000000; /* No pull-up, pull-down for PFx pins */ GPIOF->PUPDR = 0x00000000; /* Connect PGx pins to FMC Alternate function */ GPIOG->AFR[0] = 0xCCCCCCCC; GPIOG->AFR[1] = 0xCCCCCCCC; /* Configure PGx pins in Alternate function mode */ GPIOG->MODER = 0xAAAAAAAA; /* Configure PGx pins speed to 50 MHz */ GPIOG->OSPEEDR = 0xAAAAAAAA; /* Configure PGx pins Output type to push-pull */ GPIOG->OTYPER = 0x00000000; /* No pull-up, pull-down for PGx pins */ GPIOG->PUPDR = 0x00000000; #if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\ || defined(STM32F469xx) || defined(STM32F479xx) /* Connect PHx pins to FMC Alternate function */ GPIOH->AFR[0] = 0x00C0CC00; GPIOH->AFR[1] = 0xCCCCCCCC; /* Configure PHx pins in Alternate function mode */ GPIOH->MODER = 0xAAAA08A0; /* Configure PHx pins speed to 50 MHz */ GPIOH->OSPEEDR = 0xAAAA08A0; /* Configure PHx pins Output type to push-pull */ GPIOH->OTYPER = 0x00000000; /* No pull-up, pull-down for PHx pins */ GPIOH->PUPDR = 0x00000000; /* Connect PIx pins to FMC Alternate function */ GPIOI->AFR[0] = 0xCCCCCCCC; GPIOI->AFR[1] = 0x00000CC0; /* Configure PIx pins in Alternate function mode */ GPIOI->MODER = 0x0028AAAA; /* Configure PIx pins speed to 50 MHz */ GPIOI->OSPEEDR = 0x0028AAAA; /* Configure PIx pins Output type to push-pull */ GPIOI->OTYPER = 0x00000000; /* No pull-up, pull-down for PIx pins */ GPIOI->PUPDR = 0x00000000; #endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */ /*-- FMC Configuration -------------------------------------------------------*/ /* Enable the FMC interface clock */ RCC->AHB3ENR |= 0x00000001; /* Delay after an RCC peripheral clock enabling */ tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN); /* Configure and enable SDRAM bank1 */ #if defined(STM32F446xx) FMC_Bank5_6->SDCR[0] = 0x00001954; #else FMC_Bank5_6->SDCR[0] = 0x000019E4; #endif /* STM32F446xx */ FMC_Bank5_6->SDTR[0] = 0x01115351; /* SDRAM initialization sequence */ /* Clock enable command */ FMC_Bank5_6->SDCMR = 0x00000011; tmpreg = FMC_Bank5_6->SDSR & 0x00000020; while((tmpreg != 0) && (timeout-- > 0)) { tmpreg = FMC_Bank5_6->SDSR & 0x00000020; } /* Delay */ for (index = 0; index<1000; index++); /* PALL command */ FMC_Bank5_6->SDCMR = 0x00000012; timeout = 0xFFFF; while((tmpreg != 0) && (timeout-- > 0)) { tmpreg = FMC_Bank5_6->SDSR & 0x00000020; } /* Auto refresh command */ #if defined(STM32F446xx) FMC_Bank5_6->SDCMR = 0x000000F3; #else FMC_Bank5_6->SDCMR = 0x00000073; #endif /* STM32F446xx */ timeout = 0xFFFF; while((tmpreg != 0) && (timeout-- > 0)) { tmpreg = FMC_Bank5_6->SDSR & 0x00000020; } /* MRD register program */ #if defined(STM32F446xx) FMC_Bank5_6->SDCMR = 0x00044014; #else FMC_Bank5_6->SDCMR = 0x00046014; #endif /* STM32F446xx */ timeout = 0xFFFF; while((tmpreg != 0) && (timeout-- > 0)) { tmpreg = FMC_Bank5_6->SDSR & 0x00000020; } /* Set refresh count */ tmpreg = FMC_Bank5_6->SDRTR; #if defined(STM32F446xx) FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1)); #else FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1)); #endif /* STM32F446xx */ /* Disable write protection */ tmpreg = FMC_Bank5_6->SDCR[0]; FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF); #endif /* DATA_IN_ExtSDRAM */ #endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */ #if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\ || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\ || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) #if defined(DATA_IN_ExtSRAM) /*-- GPIOs Configuration -----------------------------------------------------*/ /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */ RCC->AHB1ENR |= 0x00000078; /* Delay after an RCC peripheral clock enabling */ tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN); /* Connect PDx pins to FMC Alternate function */ GPIOD->AFR[0] = 0x00CCC0CC; GPIOD->AFR[1] = 0xCCCCCCCC; /* Configure PDx pins in Alternate function mode */ GPIOD->MODER = 0xAAAA0A8A; /* Configure PDx pins speed to 100 MHz */ GPIOD->OSPEEDR = 0xFFFF0FCF; /* Configure PDx pins Output type to push-pull */ GPIOD->OTYPER = 0x00000000; /* No pull-up, pull-down for PDx pins */ GPIOD->PUPDR = 0x00000000; /* Connect PEx pins to FMC Alternate function */ GPIOE->AFR[0] = 0xC00CC0CC; GPIOE->AFR[1] = 0xCCCCCCCC; /* Configure PEx pins in Alternate function mode */ GPIOE->MODER = 0xAAAA828A; /* Configure PEx pins speed to 100 MHz */ GPIOE->OSPEEDR = 0xFFFFC3CF; /* Configure PEx pins Output type to push-pull */ GPIOE->OTYPER = 0x00000000; /* No pull-up, pull-down for PEx pins */ GPIOE->PUPDR = 0x00000000; /* Connect PFx pins to FMC Alternate function */ GPIOF->AFR[0] = 0x00CCCCCC; GPIOF->AFR[1] = 0xCCCC0000; /* Configure PFx pins in Alternate function mode */ GPIOF->MODER = 0xAA000AAA; /* Configure PFx pins speed to 100 MHz */ GPIOF->OSPEEDR = 0xFF000FFF; /* Configure PFx pins Output type to push-pull */ GPIOF->OTYPER = 0x00000000; /* No pull-up, pull-down for PFx pins */ GPIOF->PUPDR = 0x00000000; /* Connect PGx pins to FMC Alternate function */ GPIOG->AFR[0] = 0x00CCCCCC; GPIOG->AFR[1] = 0x000000C0; /* Configure PGx pins in Alternate function mode */ GPIOG->MODER = 0x00085AAA; /* Configure PGx pins speed to 100 MHz */ GPIOG->OSPEEDR = 0x000CAFFF; /* Configure PGx pins Output type to push-pull */ GPIOG->OTYPER = 0x00000000; /* No pull-up, pull-down for PGx pins */ GPIOG->PUPDR = 0x00000000; /*-- FMC/FSMC Configuration --------------------------------------------------*/ /* Enable the FMC/FSMC interface clock */ RCC->AHB3ENR |= 0x00000001; #if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) /* Delay after an RCC peripheral clock enabling */ tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN); /* Configure and enable Bank1_SRAM2 */ FMC_Bank1->BTCR[2] = 0x00001011; FMC_Bank1->BTCR[3] = 0x00000201; FMC_Bank1E->BWTR[2] = 0x0fffffff; #endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */ #if defined(STM32F469xx) || defined(STM32F479xx) /* Delay after an RCC peripheral clock enabling */ tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN); /* Configure and enable Bank1_SRAM2 */ FMC_Bank1->BTCR[2] = 0x00001091; FMC_Bank1->BTCR[3] = 0x00110212; FMC_Bank1E->BWTR[2] = 0x0fffffff; #endif /* STM32F469xx || STM32F479xx */ #if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\ || defined(STM32F412Zx) || defined(STM32F412Vx) /* Delay after an RCC peripheral clock enabling */ tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN); /* Configure and enable Bank1_SRAM2 */ FSMC_Bank1->BTCR[2] = 0x00001011; FSMC_Bank1->BTCR[3] = 0x00000201; FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF; #endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */ #endif /* DATA_IN_ExtSRAM */ #endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\ STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */ (void)(tmp); } #endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */ /** * @} */ /** * @} */ /** * @} */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/