Mercurial > public > ostc4
view Small_CPU/Src/i2c.c @ 757:39ff186b6f98
Dev Bugfix: ignore analog out of bounds limits for DiveO2 sensor:
The DiveO2 sensor provides a status information which may be used to identify if the value is valid or not. The sensor does not provide a voltage => to have a value for the voltage the value of the ppo2 is taken (equals calibration coeff of 1). For the analog out of bounds detection this value is too high and the DiveO2 is marked as out of bounds. To avoid this problem DiveO2 sensors are now excluded from the analog out of bounds detection.
author | Ideenmodellierer |
---|---|
date | Tue, 07 Mar 2023 22:14:20 +0100 |
parents | 4fe5400567e7 |
children |
line wrap: on
line source
#include "baseCPU2.h" #include "i2c.h" #include "scheduler.h" /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ /* Private macro -------------------------------------------------------------*/ // =============================================================================== // I2C addresses - see i2c.h // =============================================================================== I2C_HandleTypeDef I2cHandle; /* static void I2C_Error_Handler(void) { while(1) { } } */ GPIO_PinState HAL_I2C_Read_Data_PIN(void) { return HAL_GPIO_ReadPin(I2Cx_SDA_GPIO_PORT,I2Cx_SDA_PIN); } void HAL_I2C_Send_One_CLOCK(void) { HAL_GPIO_WritePin(I2Cx_SCL_GPIO_PORT, I2Cx_SCL_PIN, GPIO_PIN_RESET); HAL_Delay(1); HAL_GPIO_WritePin(I2Cx_SCL_GPIO_PORT, I2Cx_SCL_PIN, GPIO_PIN_SET); HAL_Delay(1); } GPIO_PinState MX_I2C1_TestAndClear(void) { GPIO_PinState retval; uint8_t repeatcnt = 3; I2C_DeInit(); HAL_I2C_ManualControl_MspInit(); /* The SDA line is expected to be HIGH if no com is pending => send dummy clock signals if that is not the case */ do { for(int i=0; i<20;i++) { if(HAL_I2C_Read_Data_PIN() == GPIO_PIN_RESET) HAL_I2C_Send_One_CLOCK(); else break; } retval = HAL_I2C_Read_Data_PIN(); }while ((repeatcnt-- > 0) && (retval != GPIO_PIN_SET)); return retval; } HAL_StatusTypeDef MX_I2C1_Init(void) { I2cHandle.Instance = I2Cx; I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT; I2cHandle.Init.ClockSpeed = 88000; /* Reduced to avoid behavior described in errata: Mismatch on the “Setup time for a repeated Start condition” */ I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE; I2cHandle.Init.DutyCycle = I2C_DUTYCYCLE_2; /* don't care if not in fast mode */ I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLED; I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLED; I2cHandle.Init.OwnAddress1 = 0x01; /* don't care because of master mode */ /* According to documentation setting filters before I2C initialization is recommended */ /* HAL_I2CEx_AnalogFilter_Config(&I2cHandle, I2C_ANALOGFILTER_ENABLED); */ HAL_I2CEx_ConfigDigitalFilter(&I2cHandle,0x0F); global.I2C_SystemStatus = HAL_I2C_Init(&I2cHandle); if(global.dataSendToSlavePending) { scheduleSpecial_Evaluate_DataSendToSlave(); } return global.I2C_SystemStatus; } void I2C_DeInit(void) { HAL_I2C_DeInit(&I2cHandle); } static uint8_t i2c_errors = 0; void I2C_Error_count(void) { i2c_errors++; } HAL_StatusTypeDef I2C_Master_Transmit( uint16_t DevAddress, uint8_t *pData, uint16_t Size) { if(global.I2C_SystemStatus != HAL_OK) return global.I2C_SystemStatus; global.I2C_SystemStatus = HAL_I2C_Master_Transmit(&I2cHandle, DevAddress, pData, Size, 10); if(global.I2C_SystemStatus != HAL_OK) { I2C_Error_count(); } return global.I2C_SystemStatus; } HAL_StatusTypeDef I2C_Master_Receive( uint16_t DevAddress, uint8_t *pData, uint16_t Size) { if(global.I2C_SystemStatus != HAL_OK) return global.I2C_SystemStatus; global.I2C_SystemStatus = HAL_I2C_Master_Receive(&I2cHandle, DevAddress, pData, Size, 10); if(global.I2C_SystemStatus != HAL_OK) { I2C_Error_count(); } return global.I2C_SystemStatus; }