view Small_CPU/Src/externalInterface.c @ 786:19ab6f3ed52a

Cleanup sensor data interface: In a very early implementation of the multiplexer the address of the mux was 0 followed by the sensors. As a resul the ID of the channels was shifted by one. To avoid confusion and because the mux address is meanwhile changed to the last address, it makes sense to return to the indexing where only the three visible sensor slots are used as reference (0,1,2).
author Ideenmodellierer
date Sun, 04 Jun 2023 21:54:24 +0200
parents 95af969fe0ae
children bb37d4f3e50e
line wrap: on
line source

/**
  ******************************************************************************
  * @file    externalInterface.c
  * @author  heinrichs weikamp gmbh
  * @version V0.0.1
  * @date    07-Nov-2020
  * @brief   Interface functionality to proceed external analog signal via i2c connection
  *
  @verbatim
  ==============================================================================
                ##### stm32f4xx_hal_i2c.c modification #####
  ==============================================================================
	The LTC2942 requires an repeated start condition without stop condition
	for data reception.

  @endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2014 heinrichs weikamp</center></h2>
  *
  ******************************************************************************
  */
/* Includes ------------------------------------------------------------------*/

#include <math.h>
#include <string.h>
#include "i2c.h"
#include "externalInterface.h"
#include "scheduler.h"
#include "uart.h"
#include "data_exchange.h"
#include "pressure.h"

extern SGlobal global;
extern UART_HandleTypeDef huart1;

#define ADC_ANSWER_LENGTH	(5u)		/* 3424 will provide addr + 4 data bytes */
#define ADC_TIMEOUT			(10u)		/* conversion stuck for unknown reason => restart */
#define ADC_REF_VOLTAGE_MV	(2048.0f)	/* reference voltage of MPC3424*/

#define ADC_START_CONVERSION		(0x80)
#define ADC_GAIN_4					(0x02)
#define ADC_GAIN_4_VALUE			(4.0f)
#define ADC_GAIN_8					(0x03)
#define ADC_GAIN_8_VALUE			(8.0f)
#define ADC_RESOLUTION_16BIT		(0x08)
#define ADC_RESOLUTION_16BIT_VALUE	(16u)
#define ADC_RESOLUTION_18BIT		(0x0C)
#define ADC_RESOLUTION_18BIT_VALUE	(18u)

#define ANSWER_CONFBYTE_INDEX		(4u)

#define LOOKUP_CO2_CORR_TABLE_SCALE	(1000u)
#define LOOKUP_CO2_CORR_TABLE_MAX	(30000u)

static uint8_t activeChannel = 0;			/* channel which is in request */
static uint8_t recBuf[ADC_ANSWER_LENGTH];
static uint8_t timeoutCnt = 0;
static uint8_t externalInterfacePresent = 0;

float externalChannel_mV[MAX_ADC_CHANNEL];
static uint8_t  externalV33_On = 0;
static uint8_t  externalADC_On = 0;
static uint8_t  externalUART_Protocol = 0;
static uint16_t externalCO2Value;
static uint16_t externalCO2SignalStrength;
static uint16_t  externalCO2Status = 0;

static uint8_t lastSensorDataId = 0;
static SSensorDataDiveO2 sensorDataDiveO2[MAX_ADC_CHANNEL];
static externalInterfaceAutoDetect_t externalAutoDetect = DETECTION_OFF;
static externalInterfaceSensorType SensorMap[EXT_INTERFACE_SENSOR_CNT] ={ SENSOR_OPTIC, SENSOR_OPTIC, SENSOR_OPTIC, SENSOR_NONE, SENSOR_NONE};
static externalInterfaceSensorType tmpSensorMap[EXT_INTERFACE_SENSOR_CNT];
static externalInterfaceSensorType MasterSensorMap[EXT_INTERFACE_SENSOR_CNT];

static float LookupCO2PressureCorrection[LOOKUP_CO2_CORR_TABLE_MAX / LOOKUP_CO2_CORR_TABLE_SCALE];		/* lookup table for pressure compensation values */


void externalInterface_Init(void)
{
	uint16_t index;
	uint16_t coeff;
	activeChannel = 0;
	timeoutCnt = 0;
	externalInterfacePresent = 0;
	if(externalInterface_StartConversion(activeChannel) == HAL_OK)
	{
		externalInterfacePresent = 1;
		global.deviceDataSendToMaster.hw_Info.extADC = 1;
	}
	global.deviceDataSendToMaster.hw_Info.checkADC = 1;

/* Create a lookup table based on GSS application note AN001: PRESSURE COMPENSATION OF A CO2 SENSOR */
/* The main purpose of the sensor in the dive application is to be a warning indicator */
/* => no exact values necessary => a lookup table with 1000ppm scaling should be sufficient */
	LookupCO2PressureCorrection [0] = -0.0014;
	for(index = 1; index < (LOOKUP_CO2_CORR_TABLE_MAX / LOOKUP_CO2_CORR_TABLE_SCALE); index++)
	{
		coeff = index * LOOKUP_CO2_CORR_TABLE_SCALE;
		LookupCO2PressureCorrection[index] = 2.811*pow(10,-38)*pow(coeff,6)- 9.817*pow(10,-32)*pow(coeff,5)+1.304*pow(10,-25)*pow(coeff,4)-8.216*pow(10,-20)*pow(coeff,3)+2.311*pow(10,-14)*pow(coeff,2) - 2.195*pow(10,-9)*coeff - 1.471*pow(10,-3);
	}
	externalInterface_InitDatastruct();
}

void externalInterface_InitDatastruct(void)
{
	uint8_t index = 0;
	/* init data values */
	externalV33_On = 0;
	externalCO2Value = 0;
	externalCO2SignalStrength = 0;
	externalCO2Status = 0;
	externalAutoDetect = DETECTION_OFF;

	for(index = 0; index < MAX_ADC_CHANNEL; index++)
	{
		externalChannel_mV[index] = 0.0;
	}
}


uint8_t externalInterface_StartConversion(uint8_t channel)
{
	uint8_t retval = 0;
	uint8_t confByte = 0;

	if(channel < MAX_ADC_CHANNEL)
	{
		confByte = ADC_START_CONVERSION | ADC_RESOLUTION_16BIT | ADC_GAIN_8;
		confByte |= channel << 5;
		retval = I2C_Master_Transmit(DEVICE_EXTERNAL_ADC, &confByte, 1);
	}
	return retval;
}

/* Check if conversion is done and trigger measurement of next channel */
uint8_t externalInterface_ReadAndSwitch()
{
	uint8_t retval = EXTERNAL_ADC_NO_DATA;
	uint8_t nextChannel;
	uint8_t* psensorMap = externalInterface_GetSensorMapPointer(0);

	if(externalADC_On)
	{
		if(I2C_Master_Receive(DEVICE_EXTERNAL_ADC, recBuf, ADC_ANSWER_LENGTH) == HAL_OK)
		{
			if((recBuf[ANSWER_CONFBYTE_INDEX] & ADC_START_CONVERSION) == 0)		/* !ready set => received data contains new value */
			{
				retval = activeChannel;										/* return channel number providing new data */
				nextChannel = activeChannel + 1;
				if(nextChannel == MAX_ADC_CHANNEL)
				{
					nextChannel = 0;
				}

				while((psensorMap[nextChannel] != SENSOR_ANALOG) && (nextChannel != activeChannel))
				{
					if(nextChannel == MAX_ADC_CHANNEL)
					{
						nextChannel = 0;
					}
					else
					{
						nextChannel++;
					}
				}

				activeChannel = nextChannel;
				externalInterface_StartConversion(activeChannel);
				timeoutCnt = 0;
			}
			else
			{
				if(timeoutCnt++ >= ADC_TIMEOUT)
				{
					externalInterface_StartConversion(activeChannel);
					timeoutCnt = 0;
				}
			}
		}
		else		/* take also i2c bus disturb into account */
		{
			if(timeoutCnt++ >= ADC_TIMEOUT)
			{
				externalInterface_StartConversion(activeChannel);
				timeoutCnt = 0;
			}
		}
	}
	return retval;
}
float externalInterface_CalculateADCValue(uint8_t channel)
{
	int32_t rawvalue = 0;
	float retValue = 0.0;
	if(channel < MAX_ADC_CHANNEL)
	{

		rawvalue = ((recBuf[0] << 16) | (recBuf[1] << 8) | (recBuf[2]));

		switch(recBuf[3] & 0x0C)			/* confbyte => Resolution bits*/
		{
			case ADC_RESOLUTION_16BIT:		rawvalue = rawvalue >> 8;										/* only 2 databytes received shift out confbyte*/
											if(rawvalue & (0x1 << (ADC_RESOLUTION_16BIT_VALUE-1)))			/* MSB set => negative number */
											{
												rawvalue |= 0xFFFF0000; 	/* set MSB for int32 */
											}
											else
											{
												rawvalue &= 0x0000FFFF;
											}
											externalChannel_mV[channel] = ADC_REF_VOLTAGE_MV * 2.0 / (float) pow(2,ADC_RESOLUTION_16BIT_VALUE);	/* calculate bit resolution */
				break;
			case ADC_RESOLUTION_18BIT:		if(rawvalue & (0x1 << (ADC_RESOLUTION_18BIT_VALUE-1)))			/* MSB set => negative number */
											{
												rawvalue |= 0xFFFE0000; 	/* set MSB for int32 */
											}
											externalChannel_mV[channel] = ADC_REF_VOLTAGE_MV * 2.0 / (float) pow(2,ADC_RESOLUTION_18BIT_VALUE);	/* calculate bit resolution */
							break;
			default: rawvalue = 0;
				break;
		}
		externalChannel_mV[channel] = externalChannel_mV[channel] * rawvalue / ADC_GAIN_8_VALUE;
		retValue = externalChannel_mV[channel];
	}
	return retValue;
}
float getExternalInterfaceChannel(uint8_t channel)
{
	float retval = 0;

	if(channel < MAX_ADC_CHANNEL)
	{
		retval = externalChannel_mV[channel];
	}
	return retval;
}

uint8_t setExternalInterfaceChannel(uint8_t channel, float value)
{
	uint8_t retval = 0;

	if(channel < MAX_ADC_CHANNEL)
	{
		externalChannel_mV[channel] = value;
		retval = 1;
	}
	return retval;
}

void externalInterface_InitPower33(void)
{
	GPIO_InitTypeDef   GPIO_InitStructure;

	GPIO_InitStructure.Pin = GPIO_PIN_7;
	GPIO_InitStructure.Mode = GPIO_MODE_OUTPUT_PP;
	GPIO_InitStructure.Pull = GPIO_PULLUP;
	GPIO_InitStructure.Speed = GPIO_SPEED_LOW;
	HAL_GPIO_Init(GPIOC, &GPIO_InitStructure);
	HAL_GPIO_WritePin(GPIOC,GPIO_PIN_7,GPIO_PIN_SET);
}


uint8_t externalInterface_isEnabledPower33()
{
	return externalV33_On;
}

uint8_t externalInterface_isEnabledADC()
{
	return externalADC_On;
}

uint8_t externalInterface_GetUARTProtocol()
{
	return externalUART_Protocol;
}

void externalInterface_SwitchPower33(uint8_t state)
{
	if(state != externalV33_On)
	{
		if(state)
		{
			HAL_GPIO_WritePin(GPIOC,GPIO_PIN_7,GPIO_PIN_RESET);
			externalV33_On = 1;
		}
		else
		{
			if(externalAutoDetect == DETECTION_OFF)
			{
				HAL_GPIO_WritePin(GPIOC,GPIO_PIN_7,GPIO_PIN_SET);
				externalV33_On = 0;
				externalInterface_SetCO2Value(0);
				externalInterface_SetCO2SignalStrength(0);
			}
		}
	}
}
void externalInterface_SwitchADC(uint8_t state)
{
	uint8_t loop = 0;
	if((state) && (externalInterfacePresent))
	{
		if(externalADC_On == 0)
		{
			activeChannel = 0;
			externalInterface_StartConversion(activeChannel);
			externalADC_On = 1;
		}
	}
	else
	{
		if(externalAutoDetect == DETECTION_OFF)			/* block deactivation requests if auto detection is active */
		{
			externalADC_On = 0;
			for(loop = 0; loop < MAX_ADC_CHANNEL; loop++)
			{
				externalChannel_mV[loop] = 0;
			}
		}
	}
}

void externalInterface_SwitchUART(uint8_t protocol)
{
	switch(protocol)
	{
		case 0:
		case (EXT_INTERFACE_UART_CO2 >> 8):
		case (EXT_INTERFACE_UART_O2 >> 8):
		case (EXT_INTERFACE_UART_SENTINEL >> 8):
				if((externalAutoDetect <= DETECTION_START)
															|| ((protocol == EXT_INTERFACE_UART_O2 >> 8) && (externalAutoDetect == DETECTION_DIGO2_0))
															|| ((protocol == EXT_INTERFACE_UART_O2 >> 8) && (externalAutoDetect == DETECTION_DIGO2_1))
															|| ((protocol == EXT_INTERFACE_UART_O2 >> 8) && (externalAutoDetect == DETECTION_DIGO2_2))
															|| ((protocol == EXT_INTERFACE_UART_O2 >> 8) && (externalAutoDetect == DETECTION_DIGO2_3))
															|| ((protocol == EXT_INTERFACE_UART_O2 >> 8) && (externalAutoDetect == DETECTION_UARTMUX))
#ifdef ENABLE_CO2_SUPPORT
															|| ((protocol == EXT_INTERFACE_UART_CO2 >> 8) && (externalAutoDetect == DETECTION_CO2))
#endif
#ifdef ENABLE_SENTINEL_MODE
														   || ((protocol == EXT_INTERFACE_UART_SENTINEL >> 8) && (externalAutoDetect == DETECTION_SENTINEL))
#endif
					)
				{
					lastSensorDataId = 0;
					externalUART_Protocol = protocol;
					MX_USART1_UART_DeInit();
					if( protocol != 0)
					{
						MX_USART1_UART_Init();
					}
				}
			break;
		default:
			break;
	}
}

void externalInterface_SetCO2Value(uint16_t CO2_ppm)
{
	float local_ppm = CO2_ppm * 10.0;		/* scalfactor */

#ifndef ENABLE_EXTERNAL_PRESSURE
	float local_corr = 0.0;

	if (local_ppm >= LOOKUP_CO2_CORR_TABLE_MAX)
	{
		local_corr = -0.0014;
	}
	else
	{
		local_corr = LookupCO2PressureCorrection[((uint16_t) (local_ppm / LOOKUP_CO2_CORR_TABLE_SCALE))];
	}
	local_ppm = local_ppm / (1.0 + (local_corr * (get_surface_mbar() - get_pressure_mbar())));
#else
/* The external pressure value is passed via ADC channel2 and calibration is done at firmware => just forward sensor data */
/* compensation is done at firmware side. This is for testing only. Take care the the same algorithm is taken as used for the lookup table */
#endif
	externalCO2Value = local_ppm / 10.0;
}

void externalInterface_SetCO2SignalStrength(uint16_t LED_qa)
{
	externalCO2SignalStrength = LED_qa;
}

uint16_t externalInterface_GetCO2Value(void)
{
	return externalCO2Value;
}

uint16_t externalInterface_GetCO2SignalStrength(void)
{
	return externalCO2SignalStrength;
}


void externalInterface_SetCO2State(uint16_t state)
{
	externalCO2Status = state;
}

uint16_t externalInterface_GetCO2State(void)
{
	return externalCO2Status;
}


uint8_t externalInterface_GetSensorData(uint8_t sensorId, uint8_t* pDataStruct)
{
	uint8_t localId = sensorId;
	if(localId == 0xFF)
	{
		localId = lastSensorDataId;
	}

	if((pDataStruct != NULL) && (localId <= MAX_ADC_CHANNEL))
	{
		memcpy(pDataStruct, &sensorDataDiveO2[localId], sizeof(SSensorDataDiveO2));
	}
	else
	{
		localId = 0xFF;
	}
	return localId;
}

void externalInterface_SetSensorData(uint8_t sensorId, uint8_t* pDataStruct)
{
	if(pDataStruct != NULL)
	{
		if((sensorId != 0xFF) && (sensorId < MAX_ADC_CHANNEL))
		{
			memcpy(&sensorDataDiveO2[sensorId], pDataStruct, sizeof(SSensorDataDiveO2));
			lastSensorDataId = sensorId;
		}
		else
		{
			memset(&sensorDataDiveO2,0,sizeof(sensorDataDiveO2));
			lastSensorDataId = 0xFF;
		}
	}
}

void externalInface_SetSensorMap(uint8_t* pMap)
{
	if(pMap != NULL)
	{
		memcpy(MasterSensorMap, pMap, 5);		/* the map is not directly copied. Copy is done via cmd request */
	}

}
uint8_t* externalInterface_GetSensorMapPointer(uint8_t finalMap)
{
	uint8_t* pret;

	if((externalAutoDetect != DETECTION_OFF) && (!finalMap))
	{
		pret = tmpSensorMap;
	}
	else
	{
		pret = SensorMap;
	}
	return pret;
}

void externalInterface_AutodetectSensor()
{
	static uint8_t tmpMuxMapping[MAX_MUX_CHANNEL];
	static uint8_t sensorIndex = 0;
	static uint8_t uartMuxChannel = 0;
	uint8_t index = 0;

	if(externalAutoDetect != DETECTION_OFF)
	{
		switch(externalAutoDetect)
		{
			case DETECTION_INIT:	sensorIndex = 0;
									uartMuxChannel = 0;
									tmpSensorMap[0] = SENSOR_OPTIC;
									tmpSensorMap[1] = SENSOR_OPTIC;
									tmpSensorMap[2] = SENSOR_OPTIC;
									tmpSensorMap[3] = SENSOR_NONE;
									tmpSensorMap[4] = SENSOR_NONE;

									for(index = 0; index < MAX_ADC_CHANNEL; index++)
									{
										UART_MapDigO2_Channel(index,index);		/* request all addresses */
										tmpMuxMapping[index] = 0xff;
									}
									UART_MapDigO2_Channel(2,3);

									if(externalInterfacePresent)
									{
										externalInterface_SwitchPower33(0);
										externalInterface_SwitchUART(0);
										for(index = 0; index < MAX_ADC_CHANNEL; index++)
										{
											externalChannel_mV[index] = 0;
										}
										externalAutoDetect = DETECTION_START;
									}
									else
									{
										externalAutoDetect = DETECTION_DONE;	/* without external interface O2 values may only be received via optical port => return default sensor map */
									}
				break;
			case DETECTION_START:		tmpSensorMap[0] = SENSOR_ANALOG;
										tmpSensorMap[1] = SENSOR_ANALOG;
										tmpSensorMap[2] = SENSOR_ANALOG;
										externalInterface_SwitchPower33(1);
										externalInterface_SwitchADC(1);
										externalAutoDetect = DETECTION_ANALOG1;
				break;
			case DETECTION_ANALOG1:	externalAutoDetect = DETECTION_ANALOG2;		/* do a second loop to make sure all adc channels could be processed */
				break;
			case DETECTION_ANALOG2:	for(index = 0; index < MAX_ADC_CHANNEL; index++)
									{
										if(externalChannel_mV[index] > MIN_ADC_VOLTAGE_MV)
										{
											tmpSensorMap[sensorIndex++] = SENSOR_ANALOG;
										}
										else
										{
											tmpSensorMap[sensorIndex++] = SENSOR_NONE;
										}
									}
									externalAutoDetect = DETECTION_UARTMUX;
									externalInterface_SwitchUART(EXT_INTERFACE_UART_O2 >> 8);
									UART_SetDigO2_Channel(MAX_MUX_CHANNEL);
				break;
			case DETECTION_UARTMUX:  	if(UART_isDigO2Connected())
										{
											uartMuxChannel = 1;
										}
										externalAutoDetect = DETECTION_DIGO2_0;
										externalInterface_SwitchUART(EXT_INTERFACE_UART_O2 >> 8);
										UART_SetDigO2_Channel(0);
										
				break;
			case DETECTION_DIGO2_0:
			case DETECTION_DIGO2_1: 
			case DETECTION_DIGO2_2:
			case DETECTION_DIGO2_3:
									if(UART_isDigO2Connected())
									{
										for(index = 0; index < 3; index++)	/* lookup a channel which may be used by digO2 */
										{
											if(tmpSensorMap[index] == SENSOR_NONE)
											{
												break;
											}
										}
										if(index == 3)
										{
											tmpSensorMap[2] = SENSOR_DIGO2;  /* digital sensor overwrites ADC */
										}
										else
										{
											tmpSensorMap[index] = SENSOR_DIGO2;
											tmpMuxMapping[externalAutoDetect - DETECTION_DIGO2_0] = index;
											if(externalAutoDetect == DETECTION_DIGO2_2 )	/* special handling needed because channel is used twice during mux detection */
											{
												UART_MapDigO2_Channel(0xff, externalAutoDetect - DETECTION_DIGO2_0);
											}
										}
									}
									else
									{
										UART_MapDigO2_Channel(0xff, externalAutoDetect - DETECTION_DIGO2_0);
									}
									if(uartMuxChannel)
									{
										externalInterface_SwitchUART(EXT_INTERFACE_UART_O2 >> 8);
										UART_SetDigO2_Channel(uartMuxChannel);
										if(uartMuxChannel < MAX_ADC_CHANNEL - 1)
										{
											uartMuxChannel++;
										}
									}
									else
									{
										externalAutoDetect = DETECTION_DIGO2_3; /* skip detection of other serial sensors */
									}
									externalAutoDetect++;
#ifdef ENABLE_CO2_SUPPORT
									if(externalAutoDetect == DETECTION_CO2)
									{
										externalInterface_SwitchUART(EXT_INTERFACE_UART_CO2 >> 8);
									}
				break;
			case DETECTION_CO2:		if(UART_isCO2Connected())
									{
										for(index = 0; index < 3; index++)	/* lookup a channel which may be used by CO2*/
										{
											if(tmpSensorMap[index] == SENSOR_NONE)
											{
												break;
											}
										}
										if(index == 3)
										{
											tmpSensorMap[sensorIndex++] = SENSOR_CO2;  /* place Co2 sensor behind O2 sensors (not visible) */
										}
										else
										{
											tmpSensorMap[index] = SENSOR_CO2;
										}

									}
									externalAutoDetect++;
#endif
#ifdef ENABLE_SENTINEL_MODE
									if(externalAutoDetect == DETECTION_SENTINEL)
									{
										externalInterface_SwitchUART(EXT_INTERFACE_UART_SENTINEL >> 8);
										UART_StartDMA_Receiption();
									}
				break;

			case DETECTION_SENTINEL:
			case DETECTION_SENTINEL2:
									if(UART_isSentinelConnected())
									{
										for(index = 0; index < 3; index++)	/* Sentinel is occupiing all sensor slots */
										{
											tmpSensorMap[index] = SENSOR_SENTINEL;
										}
										sensorIndex = 3;
									}
									externalAutoDetect++;
#endif
				break;
			case DETECTION_DONE:	if(uartMuxChannel)
									{
										tmpSensorMap[EXT_INTERFACE_SENSOR_CNT-1] = SENSOR_MUX;
									}

									for(index = 0; index < MAX_MUX_CHANNEL; index++)
									{
										UART_MapDigO2_Channel(tmpMuxMapping[index], index);
									}

									externalAutoDetect = DETECTION_OFF;
									externalInterface_SwitchUART(0);


									for(index = 0; index < MAX_ADC_CHANNEL; index++)
									{
										if(tmpSensorMap[index] == SENSOR_DIGO2) /* set Channel to first valid entry */
										{
											UART_SetDigO2_Channel(index);
											break;
										}
									}
									for(index = 0; index < MAX_ADC_CHANNEL; index++)
									{
										if(tmpSensorMap[index] != SENSOR_NONE)
										{
											break;
										}
									}

									if(index == MAX_ADC_CHANNEL)		/* return default sensor map if no sensor at all has been detected */
									{
										tmpSensorMap[0] = SENSOR_OPTIC;
										tmpSensorMap[1] = SENSOR_OPTIC;
										tmpSensorMap[2] = SENSOR_OPTIC;
									}
									memcpy(SensorMap, tmpSensorMap, sizeof(tmpSensorMap));

				break;
			default:
				break;
		}
	}
}


void externalInterface_ExecuteCmd(uint16_t Cmd)
{
	char cmdString[10];
	uint8_t cmdLength = 0;
	uint8_t index;

	switch(Cmd & 0x00FF)		/* lower byte is reserved for commands */
	{
		case EXT_INTERFACE_AUTODETECT:	externalAutoDetect = DETECTION_INIT;
										for(index = 0; index < 3; index++)
										{
											SensorMap[index] = SENSOR_SEARCH;
										}
			break;
		case EXT_INTERFACE_CO2_CALIB:	cmdLength = snprintf(cmdString, 10, "G\r\n");
			break;
		case EXT_INTERFACE_COPY_SENSORMAP:	if(externalAutoDetect == DETECTION_OFF)
											{
												memcpy(SensorMap, MasterSensorMap, 5);
												for(index = 0; index < 3; index++)
												{
													if(SensorMap[index] == SENSOR_DIGO2)
													{
														break;
													}
												}
											}
			break;
		default:
			break;
	}
	if(cmdLength != 0)
	{
		HAL_UART_Transmit(&huart1,(uint8_t*)cmdString,cmdLength,10);
	}
	return;
}