view Discovery/Src/display.c @ 845:17d9d6eddd8d Evo_2_23

Added new PreDiveCheck info page: In case a DiveO2 sensor is connected to the OSTC than the values of the DiveO2 internal pressure and temperature sensors may be used for predive checks. The pressure sensors is used for over / under pressure test and the values are visualized using a graph to make it easier to check if the pressure keeps stable. The temperature measurement gives an indication if the scrubber is getting active. This view is highly dependend on the surface temperature but may be useful e.g. for diving in european area. In addition the values ofthe connected sensors are shown.
author Ideenmodellierer
date Sun, 21 Jan 2024 22:24:36 +0100
parents 5ca177d2df5d
children f7318457df4d
line wrap: on
line source


#include "stm32f4xx_hal.h" /* for HAL_Delay() */
#include "ostc.h"
#include "display.h"

#define ENABLE_EXTENDED_COMMANDS	0xB9
#define SET_POWER									0xB1
#define SLEEP_OUT									0x11
#define DISPLAY_INVERSION_OFF			0x20
#define MEMORY_ACCESS_ONTROL			0x36
#define INTERFACE_PIXEL_FORMAT		0x3A
#define SET_RGB_INTERFACE_RELATED	0xB3
#define SET_DISPLAY_WAVEFORM			0xB4
#define SET_PANEL									0xCC
#define SET_GAMMA_CURVE_RELATED		0xE0
#define DISPLAY_ON								0x29
#define DISPLAY_OFF								0x28
#define SLEEP_IN									0x10


static void Display_Error_Handler(void);

void display_power_on__1_of_2__pre_RGB(void)
{
	/* reset system */ 
	HAL_GPIO_WritePin(DISPLAY_CSB_GPIO_PORT,DISPLAY_CSB_PIN,GPIO_PIN_SET); // chip select

	HAL_GPIO_WritePin(DISPLAY_RESETB_GPIO_PORT,DISPLAY_RESETB_PIN,GPIO_PIN_RESET);
	HAL_Delay(10);
	HAL_GPIO_WritePin(DISPLAY_RESETB_GPIO_PORT,DISPLAY_RESETB_PIN,GPIO_PIN_SET);
	HAL_Delay(10);

	/* RGB signals should be now for 2 frames or more (datasheet) */
}


static void send(uint8_t *pData, uint16_t inputlength)
{
	HAL_GPIO_WritePin(DISPLAY_CSB_GPIO_PORT,DISPLAY_CSB_PIN,GPIO_PIN_RESET); // chip select

	if(HAL_SPI_Transmit(&hspiDisplay,(uint8_t*)pData, inputlength, 10000) != HAL_OK)
		Display_Error_Handler();

	while (HAL_SPI_GetState(&hspiDisplay) != HAL_SPI_STATE_READY)
  {
  }
	HAL_GPIO_WritePin(DISPLAY_CSB_GPIO_PORT,DISPLAY_CSB_PIN,GPIO_PIN_SET); // chip select
}


static uint16_t convert8to9to8(uint8_t *pInput, uint8_t *pOutput,uint16_t inputlength)
{
	uint16_t outputlength;
	uint8_t readbit =  0x80;//0b1000000;
	uint8_t writebit = 0x40;//0b0100000;
	uint16_t i,j,k;

	outputlength = ((inputlength+7)/8)*9;

	for(i=0;i<outputlength;i++)
		pOutput[i] = 0;

	k = 0;
	for(i=0;i<inputlength;i++)
	{
		if(i != 0)
		{
			pOutput[k] |= writebit; // 9. bit
			writebit = writebit >> 1;
			if(writebit == 0)
			{
				writebit = 0x80;
				k++;
			}
		}
		for(j=0;j<8;j++)
		{
			if((pInput[i] & readbit) != 0)
			{
				pOutput[k] |= writebit;
			}
			readbit = readbit >> 1;
			if(readbit == 0)
				readbit = 0x80;
			writebit = writebit >> 1;
			if(writebit == 0)
			{
				writebit = 0x80;
				k++;
			}
		}
	}
	return outputlength;
}

void display_power_on__2_of_2__post_RGB(void)
{
	uint8_t aTxBuffer[32];
	uint8_t bTxBuffer[36];
	uint16_t i,length;

	for(i=0;i<32;i++)
		aTxBuffer[i] = 0;
	for(i=0;i<36;i++)
		bTxBuffer[i] = 0;

	aTxBuffer[0] = ENABLE_EXTENDED_COMMANDS;
	aTxBuffer[1] = 0xFF;
	aTxBuffer[2] = 0x83;
	aTxBuffer[3] = 0x63;
	length = convert8to9to8((uint8_t*)aTxBuffer,(uint8_t*)bTxBuffer,4);
	send((uint8_t*)bTxBuffer, length);

	aTxBuffer[0] = SET_POWER;
	aTxBuffer[1] = 0x81;
	aTxBuffer[2] = 0x24;
	aTxBuffer[3] = 0x04;
	aTxBuffer[4] = 0x02;
	aTxBuffer[5] = 0x02;
	aTxBuffer[6] = 0x03;
	aTxBuffer[7] = 0x10;
	aTxBuffer[8] = 0x10;
	aTxBuffer[9] = 0x34;
	aTxBuffer[10] = 0x3C;
	aTxBuffer[11] = 0x3F;
	aTxBuffer[12] = 0x3F;
	length = convert8to9to8((uint8_t*)aTxBuffer,(uint8_t*)bTxBuffer,13);
	send((uint8_t*)bTxBuffer, length);

	aTxBuffer[0] = SLEEP_OUT;
	length = convert8to9to8((uint8_t*)aTxBuffer,(uint8_t*)bTxBuffer,1);
	send((uint8_t*)bTxBuffer, length);
	HAL_Delay(5+1);

	aTxBuffer[0] = DISPLAY_INVERSION_OFF;
	length = convert8to9to8((uint8_t*)aTxBuffer,(uint8_t*)bTxBuffer,1);
	send((uint8_t*)bTxBuffer, length);

	aTxBuffer[0] = MEMORY_ACCESS_ONTROL;
	aTxBuffer[1] = 0x00;
	length = convert8to9to8((uint8_t*)aTxBuffer,(uint8_t*)bTxBuffer,2);
	send((uint8_t*)bTxBuffer, length);

	aTxBuffer[0] = INTERFACE_PIXEL_FORMAT;
	aTxBuffer[1] = 0x70;
	length = convert8to9to8((uint8_t*)aTxBuffer,(uint8_t*)bTxBuffer,2);
	send((uint8_t*)bTxBuffer, length);
	HAL_Delay(120+20);

	aTxBuffer[0] = SET_POWER;
	aTxBuffer[1] = 0x78;
	aTxBuffer[2] = 0x24;
	aTxBuffer[3] = 0x04,
	aTxBuffer[4] = 0x02;
	aTxBuffer[5] = 0x02;
	aTxBuffer[6] = 0x03;
	aTxBuffer[7] = 0x10;
	aTxBuffer[8] = 0x10;
	aTxBuffer[9] = 0x34;
	aTxBuffer[10] = 0x3C;
	aTxBuffer[11] = 0x3F;
	aTxBuffer[12] = 0x3F;
	length = convert8to9to8((uint8_t*)aTxBuffer,(uint8_t*)bTxBuffer,13);
	send((uint8_t*)bTxBuffer, length);

	aTxBuffer[0] = SET_RGB_INTERFACE_RELATED;
	aTxBuffer[1] = 0x01;
	length = convert8to9to8((uint8_t*)aTxBuffer,(uint8_t*)bTxBuffer,2);
	send((uint8_t*)bTxBuffer, length);

	aTxBuffer[0] = SET_DISPLAY_WAVEFORM;
	aTxBuffer[1] = 0x00;
	aTxBuffer[2] = 0x08;
	aTxBuffer[3] = 0x56;
	aTxBuffer[4] = 0x07;
	aTxBuffer[5] = 0x01;
	aTxBuffer[6] = 0x01;
	aTxBuffer[7] = 0x4D;
	aTxBuffer[8] = 0x01;
	aTxBuffer[9] = 0x42;
	length = convert8to9to8((uint8_t*)aTxBuffer,(uint8_t*)bTxBuffer,10);
	send((uint8_t*)bTxBuffer, length);

	aTxBuffer[0] = SET_PANEL;
	aTxBuffer[1] = 0x0B;
	length = convert8to9to8((uint8_t*)aTxBuffer,(uint8_t*)bTxBuffer,2);
	send((uint8_t*)bTxBuffer, length);

	aTxBuffer[0] = SET_GAMMA_CURVE_RELATED;
	aTxBuffer[1] = 0x01;
	aTxBuffer[2] = 0x48;
	aTxBuffer[3] = 0x4D;
	aTxBuffer[4] = 0x4E;
	aTxBuffer[5] = 0x58;
	aTxBuffer[6] = 0xF6;
	aTxBuffer[7] = 0x0B;
	aTxBuffer[8] = 0x4E;
	aTxBuffer[9] = 0x12;
	aTxBuffer[10] = 0xD5;
	aTxBuffer[11] = 0x15;
	aTxBuffer[12] = 0x95;
	aTxBuffer[13] = 0x55;
	aTxBuffer[14] = 0x8E;
	aTxBuffer[15] = 0x11;
	aTxBuffer[16] = 0x01;
	aTxBuffer[17] = 0x48;
	aTxBuffer[18] = 0x4D;
	aTxBuffer[19] = 0x55;
	aTxBuffer[20] = 0x5F;
	aTxBuffer[21] = 0xFD;
	aTxBuffer[22] = 0x0A;
	aTxBuffer[23] = 0x4E;
	aTxBuffer[24] = 0x51;
	aTxBuffer[25] = 0xD3;
	aTxBuffer[26] = 0x17;
	aTxBuffer[27] = 0x95;
	aTxBuffer[28] = 0x96;
	aTxBuffer[29] = 0x4E;
	aTxBuffer[30] = 0x11;
	length = convert8to9to8((uint8_t*)aTxBuffer,(uint8_t*)bTxBuffer,31);
	send((uint8_t*)bTxBuffer, length);
	HAL_Delay(5+1);

	aTxBuffer[0] = DISPLAY_ON;
	length = convert8to9to8((uint8_t*)aTxBuffer,(uint8_t*)bTxBuffer,1);
	send((uint8_t*)bTxBuffer, length);
}


static void Display_Error_Handler(void)
{
  while(1)
  {
  }
}