Mercurial > public > ostc4
view Common/Drivers/STM32F4xx_HAL_DRIVER_v120/Src/stm32f4xx_hal_cortex.c @ 121:0d97971b771b FlipDisplay
Use 32bit operations for buffer fills
author | Ideenmodellierer |
---|---|
date | Sun, 13 Jan 2019 18:58:23 +0100 |
parents | 5f11787b4f42 |
children |
line wrap: on
line source
/** ****************************************************************************** * @file stm32f4xx_hal_cortex.c * @author MCD Application Team * @version V1.2.0 * @date 26-December-2014 * @brief CORTEX HAL module driver. * This file provides firmware functions to manage the following * functionalities of the CORTEX: * + Initialization and de-initialization functions * + Peripheral Control functions * @verbatim ============================================================================== ##### How to use this driver ##### ============================================================================== [..] *** How to configure Interrupts using CORTEX HAL driver *** =========================================================== [..] This section provides functions allowing to configure the NVIC interrupts (IRQ). The Cortex-M4 exceptions are managed by CMSIS functions. (#) Configure the NVIC Priority Grouping using HAL_NVIC_SetPriorityGrouping() function according to the following table. (#) Configure the priority of the selected IRQ Channels using HAL_NVIC_SetPriority(). (#) Enable the selected IRQ Channels using HAL_NVIC_EnableIRQ(). (#) please refer to programing manual for details in how to configure priority. -@- When the NVIC_PRIORITYGROUP_0 is selected, IRQ preemption is no more possible. The pending IRQ priority will be managed only by the sub priority. -@- IRQ priority order (sorted by highest to lowest priority): (+@) Lowest preemption priority (+@) Lowest sub priority (+@) Lowest hardware priority (IRQ number) [..] *** How to configure Systick using CORTEX HAL driver *** ======================================================== [..] Setup SysTick Timer for time base. (+) The HAL_SYSTICK_Config() function calls the SysTick_Config() function which is a CMSIS function that: (++) Configures the SysTick Reload register with value passed as function parameter. (++) Configures the SysTick IRQ priority to the lowest value (0x0F). (++) Resets the SysTick Counter register. (++) Configures the SysTick Counter clock source to be Core Clock Source (HCLK). (++) Enables the SysTick Interrupt. (++) Starts the SysTick Counter. (+) You can change the SysTick Clock source to be HCLK_Div8 by calling the macro __HAL_CORTEX_SYSTICKCLK_CONFIG(SYSTICK_CLKSOURCE_HCLK_DIV8) just after the HAL_SYSTICK_Config() function call. The __HAL_CORTEX_SYSTICKCLK_CONFIG() macro is defined inside the stm32f4xx_hal_cortex.h file. (+) You can change the SysTick IRQ priority by calling the HAL_NVIC_SetPriority(SysTick_IRQn,...) function just after the HAL_SYSTICK_Config() function call. The HAL_NVIC_SetPriority() call the NVIC_SetPriority() function which is a CMSIS function. (+) To adjust the SysTick time base, use the following formula: Reload Value = SysTick Counter Clock (Hz) x Desired Time base (s) (++) Reload Value is the parameter to be passed for HAL_SYSTICK_Config() function (++) Reload Value should not exceed 0xFFFFFF @endverbatim ****************************************************************************** * @attention * * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ #include "stm32f4xx_hal.h" /** @addtogroup STM32F4xx_HAL_Driver * @{ */ /** @defgroup CORTEX CORTEX * @brief CORTEX HAL module driver * @{ */ #ifdef HAL_CORTEX_MODULE_ENABLED /* Private types -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Private constants ---------------------------------------------------------*/ /* Private macros ------------------------------------------------------------*/ /* Private functions ---------------------------------------------------------*/ /* Exported functions --------------------------------------------------------*/ /** @defgroup CORTEX_Exported_Functions CORTEX Exported Functions * @{ */ /** @defgroup CORTEX_Exported_Functions_Group1 Initialization and de-initialization functions * @brief Initialization and Configuration functions * @verbatim ============================================================================== ##### Initialization and de-initialization functions ##### ============================================================================== [..] This section provides the CORTEX HAL driver functions allowing to configure Interrupts Systick functionalities @endverbatim * @{ */ /** * @brief Sets the priority grouping field (preemption priority and subpriority) * using the required unlock sequence. * @param PriorityGroup: The priority grouping bits length. * This parameter can be one of the following values: * @arg NVIC_PRIORITYGROUP_0: 0 bits for preemption priority * 4 bits for subpriority * @arg NVIC_PRIORITYGROUP_1: 1 bits for preemption priority * 3 bits for subpriority * @arg NVIC_PRIORITYGROUP_2: 2 bits for preemption priority * 2 bits for subpriority * @arg NVIC_PRIORITYGROUP_3: 3 bits for preemption priority * 1 bits for subpriority * @arg NVIC_PRIORITYGROUP_4: 4 bits for preemption priority * 0 bits for subpriority * @note When the NVIC_PriorityGroup_0 is selected, IRQ preemption is no more possible. * The pending IRQ priority will be managed only by the subpriority. * @retval None */ void HAL_NVIC_SetPriorityGrouping(uint32_t PriorityGroup) { /* Check the parameters */ assert_param(IS_NVIC_PRIORITY_GROUP(PriorityGroup)); /* Set the PRIGROUP[10:8] bits according to the PriorityGroup parameter value */ NVIC_SetPriorityGrouping(PriorityGroup); } /** * @brief Sets the priority of an interrupt. * @param IRQn: External interrupt number. * This parameter can be an enumerator of IRQn_Type enumeration * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) * @param PreemptPriority: The preemption priority for the IRQn channel. * This parameter can be a value between 0 and 15 * A lower priority value indicates a higher priority * @param SubPriority: the subpriority level for the IRQ channel. * This parameter can be a value between 0 and 15 * A lower priority value indicates a higher priority. * @retval None */ void HAL_NVIC_SetPriority(IRQn_Type IRQn, uint32_t PreemptPriority, uint32_t SubPriority) { uint32_t prioritygroup = 0x00; /* Check the parameters */ assert_param(IS_NVIC_SUB_PRIORITY(SubPriority)); assert_param(IS_NVIC_PREEMPTION_PRIORITY(PreemptPriority)); prioritygroup = NVIC_GetPriorityGrouping(); NVIC_SetPriority(IRQn, NVIC_EncodePriority(prioritygroup, PreemptPriority, SubPriority)); } /** * @brief Enables a device specific interrupt in the NVIC interrupt controller. * @note To configure interrupts priority correctly, the NVIC_PriorityGroupConfig() * function should be called before. * @param IRQn External interrupt number. * This parameter can be an enumerator of IRQn_Type enumeration * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) * @retval None */ void HAL_NVIC_EnableIRQ(IRQn_Type IRQn) { /* Check the parameters */ assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); /* Enable interrupt */ NVIC_EnableIRQ(IRQn); } /** * @brief Disables a device specific interrupt in the NVIC interrupt controller. * @param IRQn External interrupt number. * This parameter can be an enumerator of IRQn_Type enumeration * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) * @retval None */ void HAL_NVIC_DisableIRQ(IRQn_Type IRQn) { /* Check the parameters */ assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); /* Disable interrupt */ NVIC_DisableIRQ(IRQn); } /** * @brief Initiates a system reset request to reset the MCU. * @retval None */ void HAL_NVIC_SystemReset(void) { /* System Reset */ NVIC_SystemReset(); } /** * @brief Initializes the System Timer and its interrupt, and starts the System Tick Timer. * Counter is in free running mode to generate periodic interrupts. * @param TicksNumb: Specifies the ticks Number of ticks between two interrupts. * @retval status: - 0 Function succeeded. * - 1 Function failed. */ uint32_t HAL_SYSTICK_Config(uint32_t TicksNumb) { return SysTick_Config(TicksNumb); } /** * @} */ /** @defgroup CORTEX_Exported_Functions_Group2 Peripheral Control functions * @brief Cortex control functions * @verbatim ============================================================================== ##### Peripheral Control functions ##### ============================================================================== [..] This subsection provides a set of functions allowing to control the CORTEX (NVIC, SYSTICK) functionalities. @endverbatim * @{ */ /** * @brief Gets the priority grouping field from the NVIC Interrupt Controller. * @retval Priority grouping field (SCB->AIRCR [10:8] PRIGROUP field) */ uint32_t HAL_NVIC_GetPriorityGrouping(void) { /* Get the PRIGROUP[10:8] field value */ return NVIC_GetPriorityGrouping(); } /** * @brief Gets the priority of an interrupt. * @param IRQn: External interrupt number. * This parameter can be an enumerator of IRQn_Type enumeration * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) * @param PriorityGroup: the priority grouping bits length. * This parameter can be one of the following values: * @arg NVIC_PRIORITYGROUP_0: 0 bits for preemption priority * 4 bits for subpriority * @arg NVIC_PRIORITYGROUP_1: 1 bits for preemption priority * 3 bits for subpriority * @arg NVIC_PRIORITYGROUP_2: 2 bits for preemption priority * 2 bits for subpriority * @arg NVIC_PRIORITYGROUP_3: 3 bits for preemption priority * 1 bits for subpriority * @arg NVIC_PRIORITYGROUP_4: 4 bits for preemption priority * 0 bits for subpriority * @param pPreemptPriority: Pointer on the Preemptive priority value (starting from 0). * @param pSubPriority: Pointer on the Subpriority value (starting from 0). * @retval None */ void HAL_NVIC_GetPriority(IRQn_Type IRQn, uint32_t PriorityGroup, uint32_t *pPreemptPriority, uint32_t *pSubPriority) { /* Check the parameters */ assert_param(IS_NVIC_PRIORITY_GROUP(PriorityGroup)); /* Get priority for Cortex-M system or device specific interrupts */ NVIC_DecodePriority(NVIC_GetPriority(IRQn), PriorityGroup, pPreemptPriority, pSubPriority); } /** * @brief Sets Pending bit of an external interrupt. * @param IRQn External interrupt number * This parameter can be an enumerator of IRQn_Type enumeration * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) * @retval None */ void HAL_NVIC_SetPendingIRQ(IRQn_Type IRQn) { /* Check the parameters */ assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); /* Set interrupt pending */ NVIC_SetPendingIRQ(IRQn); } /** * @brief Gets Pending Interrupt (reads the pending register in the NVIC * and returns the pending bit for the specified interrupt). * @param IRQn External interrupt number. * This parameter can be an enumerator of IRQn_Type enumeration * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) * @retval status: - 0 Interrupt status is not pending. * - 1 Interrupt status is pending. */ uint32_t HAL_NVIC_GetPendingIRQ(IRQn_Type IRQn) { /* Check the parameters */ assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); /* Return 1 if pending else 0 */ return NVIC_GetPendingIRQ(IRQn); } /** * @brief Clears the pending bit of an external interrupt. * @param IRQn External interrupt number. * This parameter can be an enumerator of IRQn_Type enumeration * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) * @retval None */ void HAL_NVIC_ClearPendingIRQ(IRQn_Type IRQn) { /* Check the parameters */ assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); /* Clear pending interrupt */ NVIC_ClearPendingIRQ(IRQn); } /** * @brief Gets active interrupt ( reads the active register in NVIC and returns the active bit). * @param IRQn External interrupt number * This parameter can be an enumerator of IRQn_Type enumeration * (For the complete STM32 Devices IRQ Channels list, please refer to the appropriate CMSIS device file (stm32f4xxxx.h)) * @retval status: - 0 Interrupt status is not pending. * - 1 Interrupt status is pending. */ uint32_t HAL_NVIC_GetActive(IRQn_Type IRQn) { /* Check the parameters */ assert_param(IS_NVIC_DEVICE_IRQ(IRQn)); /* Return 1 if active else 0 */ return NVIC_GetActive(IRQn); } /** * @brief Configures the SysTick clock source. * @param CLKSource: specifies the SysTick clock source. * This parameter can be one of the following values: * @arg SYSTICK_CLKSOURCE_HCLK_DIV8: AHB clock divided by 8 selected as SysTick clock source. * @arg SYSTICK_CLKSOURCE_HCLK: AHB clock selected as SysTick clock source. * @retval None */ void HAL_SYSTICK_CLKSourceConfig(uint32_t CLKSource) { /* Check the parameters */ assert_param(IS_SYSTICK_CLK_SOURCE(CLKSource)); if (CLKSource == SYSTICK_CLKSOURCE_HCLK) { SysTick->CTRL |= SYSTICK_CLKSOURCE_HCLK; } else { SysTick->CTRL &= ~SYSTICK_CLKSOURCE_HCLK; } } /** * @brief This function handles SYSTICK interrupt request. * @retval None */ void HAL_SYSTICK_IRQHandler(void) { HAL_SYSTICK_Callback(); } /** * @brief SYSTICK callback. * @retval None */ __weak void HAL_SYSTICK_Callback(void) { /* NOTE : This function Should not be modified, when the callback is needed, the HAL_SYSTICK_Callback could be implemented in the user file */ } /** * @} */ /** * @} */ #endif /* HAL_CORTEX_MODULE_ENABLED */ /** * @} */ /** * @} */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/