Mercurial > public > ostc4

view Small_CPU/Inc/batteryCharger.h @ 855:012f94ec2fe0 Evo_2_23

Find changesets by keywords (author, files, the commit message), revision number or hash, or revset expression.
Redefine Deco gas creation function: The old function needed a lot of iteration to get through all gases. With the change to define the first gas in PSCR mode as deco gas for calculation (because the actual gas could be not breathable close to surface => deco planing would be based on > 80% nitrogen increasing the deco prediction higher than necessary) the need showed up to somehow define the first gas as deco gas. Instead of manipulating the gas attribute the deco list creation function was changed to create the list based on gas line pointer information instead of index lists. The new function needs less iterations for sorting and is more flexible regarding gas handling.
author Ideenmodellierer
date Mon, 18 Mar 2024 21:52:25 +0100
parents 1b995079c045
children d32901746950
line wrap: on
line source

/**
  ******************************************************************************
  * @file    batteryCharger.h
  * @author  heinrichs weikamp gmbh
  * @date    09-Dec-2014
  * @version V0.0.1
  * @since   09-Dec-2014
  * @brief	 LTC4054 Standalone Linear Li-Ion Battery Charger 
  *           
  @verbatim                 
  ============================================================================== 
                        ##### How to use #####
  ============================================================================== 
  @endverbatim
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT(c) 2015 heinrichs weikamp</center></h2>
  *
  ******************************************************************************
  */ 

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef BATTERY_CHARGER_H
#define BATTERY_CHARGER_H

#ifdef __cplusplus
 extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include <stdint.h>

#define CHARGE_IN_PIN				GPIO_PIN_2
#define CHARGE_IN_GPIO_PORT			GPIOC
#define CHARGE_IN_GPIO_ENABLE()		__GPIOC_CLK_ENABLE()

#define CHARGE_OUT_PIN				GPIO_PIN_1
#define CHARGE_OUT_GPIO_PORT		GPIOC
#define CHARGE_OUT_GPIO_ENABLE()	__GPIOC_CLK_ENABLE()

 typedef enum
 {
 	Charger_NotConnected = 0,		/* This is identified reading CHARGE_IN_PIN == HIGH */
 	Charger_WarmUp,					/* Charging started but counter did not yet reach a certain limit (used to debounce connect / disconnect events to avoid multiple increases of statistic charging cycle counter) */
 	Charger_Active,					/* Charging identified by  CHARGE_IN_PIN == LOW for a certain time */
 	Charger_Finished,
 	Charger_LostConnection,			/* Intermediate state to debounce disconnecting events (including charging error state like over temperature) */
 	Charger_ColdStart,				/* Cold start condition => check if an loaded battery has been inserted */
 	Charger_END
 } chargerState_t;


uint8_t get_charge_status(void);
void init_battery_charger_status(void);
void set_charge_state(chargerState_t newState);
uint8_t get_charge_state(void);
void ReInit_battery_charger_status_pins(void);
void DeInit_battery_charger_status_pins(void);
void battery_charger_get_status_and_contral_battery_gas_gauge(uint8_t cycleTimeBase);

#ifdef __cplusplus
}
#endif

#endif /* BATTERY_CHARGER_H */

/************************ (C) COPYRIGHT heinrichs weikamp *****END OF FILE****/