diff Small_CPU/Inc/uartProtocol_Co2.h @ 798:e9eba334b942

Migrated CO2 protocol implementation to new format: The previous implementation was a monolithic protocol implementation which was not usable together with the multiplexer. The new implementation moves the CO2 implementation into a separate C file and decoubles the upper layer external interface, which is not able to handle DiveO2 and CO2 sensors in parallel without restriction to port assignments.
author Ideenmodellierer
date Mon, 07 Aug 2023 20:29:44 +0200
parents
children c3dd461ca3f9
line wrap: on
line diff
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/Small_CPU/Inc/uartProtocol_Co2.h	Mon Aug 07 20:29:44 2023 +0200
@@ -0,0 +1,81 @@
+/**
+  ******************************************************************************
+  * @file    uartProtocol_Co2.h
+  * @author  heinrichs weikamp gmbh
+  * @version V0.0.1
+  * @date    31-Jul-2023
+  * @brief	 Interface functionality to handle external, UART based CO2 sensors
+  *
+  @verbatim
+  ==============================================================================
+                        ##### How to use #####
+  ==============================================================================
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2014 heinrichs weikamp</center></h2>
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef UART_PROTOCOL_CO2_H
+#define UART_PROTOCOL_CO2_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "configuration.h"
+#include "stm32f4xx_hal.h"
+
+ typedef enum
+  {
+	UART_CO2_INIT = 0,		/* Default Status for every sensor type */
+	UART_CO2_IDLE,			/* sensor detected and no communication pending */
+	UART_CO2_ERROR,
+ 	UART_CO2_SETUP = 10,	/* collecting data needed to be read out of the sensor once at startup */
+  	UART_CO2_OPERATING,		/* normal operation */
+	UART_CO2_CALIBRATE		/* request calibration */
+  } uartCO2Status_t;
+
+  typedef enum
+  {
+  	RX_Ready= 0,					/* Initial state */
+ 	RX_DetectStart,					/* validate start byte */
+ 	RX_SelectData,					/* Data contained in this frame */
+  	RX_Data0,						/* Process incoming data */
+ 	RX_Data1,
+ 	RX_Data2,
+ 	RX_Data3,
+ 	RX_Data4,
+ 	RX_Data5,
+ 	RX_Data6,
+ 	RX_Data7,
+ 	RX_Data8,
+ 	RX_Data9,
+ 	RX_Data10,
+ 	RX_Data11,
+ 	RX_Data12,
+ 	RX_DataComplete
+  } receiveState_t;
+
+
+ typedef enum
+ {
+ 	CO2CMD_MODE_POLL,		/* Set operation mode of sensor to polling => only send data if requested */
+ 	CO2CMD_MODE_STREAM,		/* Set operation mode of sensor to streaming => send data every two seconds */
+ 	CO2CMD_CALIBRATE,		/* Calibrate sensor */
+ 	CO2CMD_GETSCALE,		/* Get scaling factor */
+ 	CO2CMD_GETDATA			/* Read sensor data */
+ } co2SensorCmd_t;
+
+
+void uartCo2_Control(void);
+void uartCo2_ProcessData(uint8_t data);
+void uartCo2_SendCmd(uint8_t CO2Cmd, uint8_t *cmdString, uint8_t *cmdLength);
+uint8_t uartCo2_isSensorConnected();
+
+#endif /* UART_PROTOCOL_CO2_H */