--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/Common/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c	Thu Mar 07 15:06:43 2019 +0100
@@ -0,0 +1,1113 @@
+/**
+  ******************************************************************************
+  * @file    stm32f4xx_hal_rcc.c
+  * @author  MCD Application Team
+  * @brief   RCC HAL module driver.
+  *          This file provides firmware functions to manage the following
+  *          functionalities of the Reset and Clock Control (RCC) peripheral:
+  *           + Initialization and de-initialization functions
+  *           + Peripheral Control functions
+  *
+  @verbatim
+  ==============================================================================
+                      ##### RCC specific features #####
+  ==============================================================================
+    [..]
+      After reset the device is running from Internal High Speed oscillator
+      (HSI 16MHz) with Flash 0 wait state, Flash prefetch buffer, D-Cache
+      and I-Cache are disabled, and all peripherals are off except internal
+      SRAM, Flash and JTAG.
+      (+) There is no prescaler on High speed (AHB) and Low speed (APB) busses;
+          all peripherals mapped on these busses are running at HSI speed.
+      (+) The clock for all peripherals is switched off, except the SRAM and FLASH.
+      (+) All GPIOs are in input floating state, except the JTAG pins which
+          are assigned to be used for debug purpose.
+
+    [..]
+      Once the device started from reset, the user application has to:
+      (+) Configure the clock source to be used to drive the System clock
+          (if the application needs higher frequency/performance)
+      (+) Configure the System clock frequency and Flash settings
+      (+) Configure the AHB and APB busses prescalers
+      (+) Enable the clock for the peripheral(s) to be used
+      (+) Configure the clock source(s) for peripherals which clocks are not
+          derived from the System clock (I2S, RTC, ADC, USB OTG FS/SDIO/RNG)
+
+                      ##### RCC Limitations #####
+  ==============================================================================
+    [..]
+      A delay between an RCC peripheral clock enable and the effective peripheral
+      enabling should be taken into account in order to manage the peripheral read/write
+      from/to registers.
+      (+) This delay depends on the peripheral mapping.
+      (+) If peripheral is mapped on AHB: the delay is 2 AHB clock cycle
+          after the clock enable bit is set on the hardware register
+      (+) If peripheral is mapped on APB: the delay is 2 APB clock cycle
+          after the clock enable bit is set on the hardware register
+
+    [..]
+      Implemented Workaround:
+      (+) For AHB & APB peripherals, a dummy read to the peripheral register has been
+          inserted in each __HAL_RCC_PPP_CLK_ENABLE() macro.
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f4xx_hal.h"
+
+/** @addtogroup STM32F4xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup RCC RCC
+  * @brief RCC HAL module driver
+  * @{
+  */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/** @addtogroup RCC_Private_Constants
+  * @{
+  */
+
+/* Private macro -------------------------------------------------------------*/
+#define __MCO1_CLK_ENABLE()   __HAL_RCC_GPIOA_CLK_ENABLE()
+#define MCO1_GPIO_PORT        GPIOA
+#define MCO1_PIN              GPIO_PIN_8
+
+#define __MCO2_CLK_ENABLE()   __HAL_RCC_GPIOC_CLK_ENABLE()
+#define MCO2_GPIO_PORT         GPIOC
+#define MCO2_PIN               GPIO_PIN_9
+/**
+  * @}
+  */
+
+/* Private variables ---------------------------------------------------------*/
+/** @defgroup RCC_Private_Variables RCC Private Variables
+  * @{
+  */
+/**
+  * @}
+  */
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup RCC_Exported_Functions RCC Exported Functions
+  *  @{
+  */
+
+/** @defgroup RCC_Exported_Functions_Group1 Initialization and de-initialization functions
+ *  @brief    Initialization and Configuration functions
+ *
+@verbatim
+ ===============================================================================
+           ##### Initialization and de-initialization functions #####
+ ===============================================================================
+    [..]
+      This section provides functions allowing to configure the internal/external oscillators
+      (HSE, HSI, LSE, LSI, PLL, CSS and MCO) and the System busses clocks (SYSCLK, AHB, APB1
+       and APB2).
+
+    [..] Internal/external clock and PLL configuration
+         (#) HSI (high-speed internal), 16 MHz factory-trimmed RC used directly or through
+             the PLL as System clock source.
+
+         (#) LSI (low-speed internal), 32 KHz low consumption RC used as IWDG and/or RTC
+             clock source.
+
+         (#) HSE (high-speed external), 4 to 26 MHz crystal oscillator used directly or
+             through the PLL as System clock source. Can be used also as RTC clock source.
+
+         (#) LSE (low-speed external), 32 KHz oscillator used as RTC clock source.
+
+         (#) PLL (clocked by HSI or HSE), featuring two different output clocks:
+           (++) The first output is used to generate the high speed system clock (up to 168 MHz)
+           (++) The second output is used to generate the clock for the USB OTG FS (48 MHz),
+                the random analog generator (<=48 MHz) and the SDIO (<= 48 MHz).
+
+         (#) CSS (Clock security system), once enable using the macro __HAL_RCC_CSS_ENABLE()
+             and if a HSE clock failure occurs(HSE used directly or through PLL as System
+             clock source), the System clocks automatically switched to HSI and an interrupt
+             is generated if enabled. The interrupt is linked to the Cortex-M4 NMI
+             (Non-Maskable Interrupt) exception vector.
+
+         (#) MCO1 (microcontroller clock output), used to output HSI, LSE, HSE or PLL
+             clock (through a configurable prescaler) on PA8 pin.
+
+         (#) MCO2 (microcontroller clock output), used to output HSE, PLL, SYSCLK or PLLI2S
+             clock (through a configurable prescaler) on PC9 pin.
+
+    [..] System, AHB and APB busses clocks configuration
+         (#) Several clock sources can be used to drive the System clock (SYSCLK): HSI,
+             HSE and PLL.
+             The AHB clock (HCLK) is derived from System clock through configurable
+             prescaler and used to clock the CPU, memory and peripherals mapped
+             on AHB bus (DMA, GPIO...). APB1 (PCLK1) and APB2 (PCLK2) clocks are derived
+             from AHB clock through configurable prescalers and used to clock
+             the peripherals mapped on these busses. You can use
+             "HAL_RCC_GetSysClockFreq()" function to retrieve the frequencies of these clocks.
+
+         (#) For the STM32F405xx/07xx and STM32F415xx/17xx devices, the maximum
+             frequency of the SYSCLK and HCLK is 168 MHz, PCLK2 84 MHz and PCLK1 42 MHz.
+             Depending on the device voltage range, the maximum frequency should
+             be adapted accordingly (refer to the product datasheets for more details).
+
+         (#) For the STM32F42xxx, STM32F43xxx, STM32F446xx, STM32F469xx and STM32F479xx devices,
+             the maximum frequency of the SYSCLK and HCLK is 180 MHz, PCLK2 90 MHz and PCLK1 45 MHz.
+             Depending on the device voltage range, the maximum frequency should
+             be adapted accordingly (refer to the product datasheets for more details).
+
+         (#) For the STM32F401xx, the maximum frequency of the SYSCLK and HCLK is 84 MHz,
+             PCLK2 84 MHz and PCLK1 42 MHz.
+             Depending on the device voltage range, the maximum frequency should
+             be adapted accordingly (refer to the product datasheets for more details).
+
+         (#) For the STM32F41xxx, the maximum frequency of the SYSCLK and HCLK is 100 MHz,
+             PCLK2 100 MHz and PCLK1 50 MHz.
+             Depending on the device voltage range, the maximum frequency should
+             be adapted accordingly (refer to the product datasheets for more details).
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Resets the RCC clock configuration to the default reset state.
+  * @note   The default reset state of the clock configuration is given below:
+  *            - HSI ON and used as system clock source
+  *            - HSE and PLL OFF
+  *            - AHB, APB1 and APB2 prescaler set to 1.
+  *            - CSS, MCO1 and MCO2 OFF
+  *            - All interrupts disabled
+  * @note   This function doesn't modify the configuration of the
+  *            - Peripheral clocks
+  *            - LSI, LSE and RTC clocks
+  * @retval HAL status
+  */
+__weak HAL_StatusTypeDef HAL_RCC_DeInit(void)
+{
+  return HAL_OK;
+}
+
+/**
+  * @brief  Initializes the RCC Oscillators according to the specified parameters in the
+  *         RCC_OscInitTypeDef.
+  * @param  RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that
+  *         contains the configuration information for the RCC Oscillators.
+  * @note   The PLL is not disabled when used as system clock.
+  * @note   Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not
+  *         supported by this API. User should request a transition to LSE Off
+  *         first and then LSE On or LSE Bypass.
+  * @note   Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not
+  *         supported by this API. User should request a transition to HSE Off
+  *         first and then HSE On or HSE Bypass.
+  * @retval HAL status
+  */
+__weak HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef  *RCC_OscInitStruct)
+{
+  uint32_t tickstart;
+
+  /* Check Null pointer */
+  if(RCC_OscInitStruct == NULL)
+  {
+    return HAL_ERROR;
+  }
+
+  /* Check the parameters */
+  assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType));
+  /*------------------------------- HSE Configuration ------------------------*/
+  if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE)
+  {
+    /* Check the parameters */
+    assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState));
+    /* When the HSE is used as system clock or clock source for PLL in these cases HSE will not disabled */
+    if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSE) ||\
+      ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSE)))
+    {
+      if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) && (RCC_OscInitStruct->HSEState == RCC_HSE_OFF))
+      {
+        return HAL_ERROR;
+      }
+    }
+    else
+    {
+      /* Set the new HSE configuration ---------------------------------------*/
+      __HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState);
+
+      /* Check the HSE State */
+      if((RCC_OscInitStruct->HSEState) != RCC_HSE_OFF)
+      {
+        /* Get Start Tick */
+        tickstart = HAL_GetTick();
+
+        /* Wait till HSE is ready */
+        while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET)
+        {
+          if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE)
+          {
+            return HAL_TIMEOUT;
+          }
+        }
+      }
+      else
+      {
+        /* Get Start Tick */
+        tickstart = HAL_GetTick();
+
+        /* Wait till HSE is bypassed or disabled */
+        while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET)
+        {
+          if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE)
+          {
+            return HAL_TIMEOUT;
+          }
+        }
+      }
+    }
+  }
+  /*----------------------------- HSI Configuration --------------------------*/
+  if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI)
+  {
+    /* Check the parameters */
+    assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState));
+    assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue));
+
+    /* Check if HSI is used as system clock or as PLL source when PLL is selected as system clock */
+    if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSI) ||\
+      ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSI)))
+    {
+      /* When HSI is used as system clock it will not disabled */
+      if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON))
+      {
+        return HAL_ERROR;
+      }
+      /* Otherwise, just the calibration is allowed */
+      else
+      {
+        /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/
+        __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue);
+      }
+    }
+    else
+    {
+      /* Check the HSI State */
+      if((RCC_OscInitStruct->HSIState)!= RCC_HSI_OFF)
+      {
+        /* Enable the Internal High Speed oscillator (HSI). */
+        __HAL_RCC_HSI_ENABLE();
+
+        /* Get Start Tick*/
+        tickstart = HAL_GetTick();
+
+        /* Wait till HSI is ready */
+        while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET)
+        {
+          if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE)
+          {
+            return HAL_TIMEOUT;
+          }
+        }
+
+        /* Adjusts the Internal High Speed oscillator (HSI) calibration value. */
+        __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue);
+      }
+      else
+      {
+        /* Disable the Internal High Speed oscillator (HSI). */
+        __HAL_RCC_HSI_DISABLE();
+
+        /* Get Start Tick*/
+        tickstart = HAL_GetTick();
+
+        /* Wait till HSI is ready */
+        while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET)
+        {
+          if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE)
+          {
+            return HAL_TIMEOUT;
+          }
+        }
+      }
+    }
+  }
+  /*------------------------------ LSI Configuration -------------------------*/
+  if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI)
+  {
+    /* Check the parameters */
+    assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState));
+
+    /* Check the LSI State */
+    if((RCC_OscInitStruct->LSIState)!= RCC_LSI_OFF)
+    {
+      /* Enable the Internal Low Speed oscillator (LSI). */
+      __HAL_RCC_LSI_ENABLE();
+
+      /* Get Start Tick*/
+      tickstart = HAL_GetTick();
+
+      /* Wait till LSI is ready */
+      while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == RESET)
+      {
+        if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE)
+        {
+          return HAL_TIMEOUT;
+        }
+      }
+    }
+    else
+    {
+      /* Disable the Internal Low Speed oscillator (LSI). */
+      __HAL_RCC_LSI_DISABLE();
+
+      /* Get Start Tick */
+      tickstart = HAL_GetTick();
+
+      /* Wait till LSI is ready */
+      while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != RESET)
+      {
+        if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE)
+        {
+          return HAL_TIMEOUT;
+        }
+      }
+    }
+  }
+  /*------------------------------ LSE Configuration -------------------------*/
+  if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE)
+  {
+    FlagStatus       pwrclkchanged = RESET;
+
+    /* Check the parameters */
+    assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState));
+
+    /* Update LSE configuration in Backup Domain control register    */
+    /* Requires to enable write access to Backup Domain of necessary */
+    if(__HAL_RCC_PWR_IS_CLK_DISABLED())
+    {
+      __HAL_RCC_PWR_CLK_ENABLE();
+      pwrclkchanged = SET;
+    }
+
+    if(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP))
+    {
+      /* Enable write access to Backup domain */
+      SET_BIT(PWR->CR, PWR_CR_DBP);
+
+      /* Wait for Backup domain Write protection disable */
+      tickstart = HAL_GetTick();
+
+      while(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP))
+      {
+        if((HAL_GetTick() - tickstart) > RCC_DBP_TIMEOUT_VALUE)
+        {
+          return HAL_TIMEOUT;
+        }
+      }
+    }
+
+    /* Set the new LSE configuration -----------------------------------------*/
+    __HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState);
+    /* Check the LSE State */
+    if((RCC_OscInitStruct->LSEState) != RCC_LSE_OFF)
+    {
+      /* Get Start Tick*/
+      tickstart = HAL_GetTick();
+
+      /* Wait till LSE is ready */
+      while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET)
+      {
+        if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE)
+        {
+          return HAL_TIMEOUT;
+        }
+      }
+    }
+    else
+    {
+      /* Get Start Tick */
+      tickstart = HAL_GetTick();
+
+      /* Wait till LSE is ready */
+      while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET)
+      {
+        if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE)
+        {
+          return HAL_TIMEOUT;
+        }
+      }
+    }
+
+    /* Restore clock configuration if changed */
+    if(pwrclkchanged == SET)
+    {
+      __HAL_RCC_PWR_CLK_DISABLE();
+    }
+  }
+  /*-------------------------------- PLL Configuration -----------------------*/
+  /* Check the parameters */
+  assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState));
+  if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE)
+  {
+    /* Check if the PLL is used as system clock or not */
+    if(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_PLL)
+    {
+      if((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON)
+      {
+        /* Check the parameters */
+        assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource));
+        assert_param(IS_RCC_PLLM_VALUE(RCC_OscInitStruct->PLL.PLLM));
+        assert_param(IS_RCC_PLLN_VALUE(RCC_OscInitStruct->PLL.PLLN));
+        assert_param(IS_RCC_PLLP_VALUE(RCC_OscInitStruct->PLL.PLLP));
+        assert_param(IS_RCC_PLLQ_VALUE(RCC_OscInitStruct->PLL.PLLQ));
+
+        /* Disable the main PLL. */
+        __HAL_RCC_PLL_DISABLE();
+
+        /* Get Start Tick */
+        tickstart = HAL_GetTick();
+
+        /* Wait till PLL is ready */
+        while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET)
+        {
+          if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
+          {
+            return HAL_TIMEOUT;
+          }
+        }
+
+        /* Configure the main PLL clock source, multiplication and division factors. */
+        WRITE_REG(RCC->PLLCFGR, (RCC_OscInitStruct->PLL.PLLSource                                            | \
+                                 RCC_OscInitStruct->PLL.PLLM                                                 | \
+                                 (RCC_OscInitStruct->PLL.PLLN << RCC_PLLCFGR_PLLN_Pos)             | \
+                                 (((RCC_OscInitStruct->PLL.PLLP >> 1U) - 1U) << RCC_PLLCFGR_PLLP_Pos) | \
+                                 (RCC_OscInitStruct->PLL.PLLQ << RCC_PLLCFGR_PLLQ_Pos)));
+        /* Enable the main PLL. */
+        __HAL_RCC_PLL_ENABLE();
+
+        /* Get Start Tick */
+        tickstart = HAL_GetTick();
+
+        /* Wait till PLL is ready */
+        while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET)
+        {
+          if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
+          {
+            return HAL_TIMEOUT;
+          }
+        }
+      }
+      else
+      {
+        /* Disable the main PLL. */
+        __HAL_RCC_PLL_DISABLE();
+
+        /* Get Start Tick */
+        tickstart = HAL_GetTick();
+
+        /* Wait till PLL is ready */
+        while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET)
+        {
+          if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
+          {
+            return HAL_TIMEOUT;
+          }
+        }
+      }
+    }
+    else
+    {
+      return HAL_ERROR;
+    }
+  }
+  return HAL_OK;
+}
+
+/**
+  * @brief  Initializes the CPU, AHB and APB busses clocks according to the specified
+  *         parameters in the RCC_ClkInitStruct.
+  * @param  RCC_ClkInitStruct pointer to an RCC_OscInitTypeDef structure that
+  *         contains the configuration information for the RCC peripheral.
+  * @param  FLatency FLASH Latency, this parameter depend on device selected
+  *
+  * @note   The SystemCoreClock CMSIS variable is used to store System Clock Frequency
+  *         and updated by HAL_RCC_GetHCLKFreq() function called within this function
+  *
+  * @note   The HSI is used (enabled by hardware) as system clock source after
+  *         startup from Reset, wake-up from STOP and STANDBY mode, or in case
+  *         of failure of the HSE used directly or indirectly as system clock
+  *         (if the Clock Security System CSS is enabled).
+  *
+  * @note   A switch from one clock source to another occurs only if the target
+  *         clock source is ready (clock stable after startup delay or PLL locked).
+  *         If a clock source which is not yet ready is selected, the switch will
+  *         occur when the clock source will be ready.
+  *
+  * @note   Depending on the device voltage range, the software has to set correctly
+  *         HPRE[3:0] bits to ensure that HCLK not exceed the maximum allowed frequency
+  *         (for more details refer to section above "Initialization/de-initialization functions")
+  * @retval None
+  */
+HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef  *RCC_ClkInitStruct, uint32_t FLatency)
+{
+  uint32_t tickstart;
+
+  /* Check Null pointer */
+  if(RCC_ClkInitStruct == NULL)
+  {
+    return HAL_ERROR;
+  }
+
+  /* Check the parameters */
+  assert_param(IS_RCC_CLOCKTYPE(RCC_ClkInitStruct->ClockType));
+  assert_param(IS_FLASH_LATENCY(FLatency));
+
+  /* To correctly read data from FLASH memory, the number of wait states (LATENCY)
+    must be correctly programmed according to the frequency of the CPU clock
+    (HCLK) and the supply voltage of the device. */
+
+  /* Increasing the number of wait states because of higher CPU frequency */
+  if(FLatency > __HAL_FLASH_GET_LATENCY())
+  {
+    /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */
+    __HAL_FLASH_SET_LATENCY(FLatency);
+
+    /* Check that the new number of wait states is taken into account to access the Flash
+    memory by reading the FLASH_ACR register */
+    if(__HAL_FLASH_GET_LATENCY() != FLatency)
+    {
+      return HAL_ERROR;
+    }
+  }
+
+  /*-------------------------- HCLK Configuration --------------------------*/
+  if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK)
+  {
+    /* Set the highest APBx dividers in order to ensure that we do not go through
+       a non-spec phase whatever we decrease or increase HCLK. */
+    if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1)
+    {
+      MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_HCLK_DIV16);
+    }
+
+    if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2)
+    {
+      MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, (RCC_HCLK_DIV16 << 3));
+    }
+
+    assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider));
+    MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider);
+  }
+
+  /*------------------------- SYSCLK Configuration ---------------------------*/
+  if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK)
+  {
+    assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource));
+
+    /* HSE is selected as System Clock Source */
+    if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE)
+    {
+      /* Check the HSE ready flag */
+      if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET)
+      {
+        return HAL_ERROR;
+      }
+    }
+    /* PLL is selected as System Clock Source */
+    else if((RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK)   ||
+            (RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLRCLK))
+    {
+      /* Check the PLL ready flag */
+      if(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET)
+      {
+        return HAL_ERROR;
+      }
+    }
+    /* HSI is selected as System Clock Source */
+    else
+    {
+      /* Check the HSI ready flag */
+      if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET)
+      {
+        return HAL_ERROR;
+      }
+    }
+
+    __HAL_RCC_SYSCLK_CONFIG(RCC_ClkInitStruct->SYSCLKSource);
+
+    /* Get Start Tick */
+    tickstart = HAL_GetTick();
+
+    while (__HAL_RCC_GET_SYSCLK_SOURCE() != (RCC_ClkInitStruct->SYSCLKSource << RCC_CFGR_SWS_Pos))
+    {
+      if ((HAL_GetTick() - tickstart) > CLOCKSWITCH_TIMEOUT_VALUE)
+      {
+        return HAL_TIMEOUT;
+      }
+    }
+  }
+
+  /* Decreasing the number of wait states because of lower CPU frequency */
+  if(FLatency < __HAL_FLASH_GET_LATENCY())
+  {
+     /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */
+    __HAL_FLASH_SET_LATENCY(FLatency);
+
+    /* Check that the new number of wait states is taken into account to access the Flash
+    memory by reading the FLASH_ACR register */
+    if(__HAL_FLASH_GET_LATENCY() != FLatency)
+    {
+      return HAL_ERROR;
+    }
+  }
+
+  /*-------------------------- PCLK1 Configuration ---------------------------*/
+  if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1)
+  {
+    assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB1CLKDivider));
+    MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_ClkInitStruct->APB1CLKDivider);
+  }
+
+  /*-------------------------- PCLK2 Configuration ---------------------------*/
+  if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2)
+  {
+    assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB2CLKDivider));
+    MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, ((RCC_ClkInitStruct->APB2CLKDivider) << 3U));
+  }
+
+  /* Update the SystemCoreClock global variable */
+  SystemCoreClock = HAL_RCC_GetSysClockFreq() >> AHBPrescTable[(RCC->CFGR & RCC_CFGR_HPRE)>> RCC_CFGR_HPRE_Pos];
+
+  /* Configure the source of time base considering new system clocks settings */
+  HAL_InitTick (TICK_INT_PRIORITY);
+
+  return HAL_OK;
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup RCC_Exported_Functions_Group2 Peripheral Control functions
+ *  @brief   RCC clocks control functions
+ *
+@verbatim
+ ===============================================================================
+                      ##### Peripheral Control functions #####
+ ===============================================================================
+    [..]
+    This subsection provides a set of functions allowing to control the RCC Clocks
+    frequencies.
+
+@endverbatim
+  * @{
+  */
+
+/**
+  * @brief  Selects the clock source to output on MCO1 pin(PA8) or on MCO2 pin(PC9).
+  * @note   PA8/PC9 should be configured in alternate function mode.
+  * @param  RCC_MCOx specifies the output direction for the clock source.
+  *          This parameter can be one of the following values:
+  *            @arg RCC_MCO1: Clock source to output on MCO1 pin(PA8).
+  *            @arg RCC_MCO2: Clock source to output on MCO2 pin(PC9).
+  * @param  RCC_MCOSource specifies the clock source to output.
+  *          This parameter can be one of the following values:
+  *            @arg RCC_MCO1SOURCE_HSI: HSI clock selected as MCO1 source
+  *            @arg RCC_MCO1SOURCE_LSE: LSE clock selected as MCO1 source
+  *            @arg RCC_MCO1SOURCE_HSE: HSE clock selected as MCO1 source
+  *            @arg RCC_MCO1SOURCE_PLLCLK: main PLL clock selected as MCO1 source
+  *            @arg RCC_MCO2SOURCE_SYSCLK: System clock (SYSCLK) selected as MCO2 source
+  *            @arg RCC_MCO2SOURCE_PLLI2SCLK: PLLI2S clock selected as MCO2 source, available for all STM32F4 devices except STM32F410xx
+  *            @arg RCC_MCO2SOURCE_I2SCLK: I2SCLK clock selected as MCO2 source, available only for STM32F410Rx devices
+  *            @arg RCC_MCO2SOURCE_HSE: HSE clock selected as MCO2 source
+  *            @arg RCC_MCO2SOURCE_PLLCLK: main PLL clock selected as MCO2 source
+  * @param  RCC_MCODiv specifies the MCOx prescaler.
+  *          This parameter can be one of the following values:
+  *            @arg RCC_MCODIV_1: no division applied to MCOx clock
+  *            @arg RCC_MCODIV_2: division by 2 applied to MCOx clock
+  *            @arg RCC_MCODIV_3: division by 3 applied to MCOx clock
+  *            @arg RCC_MCODIV_4: division by 4 applied to MCOx clock
+  *            @arg RCC_MCODIV_5: division by 5 applied to MCOx clock
+  * @note  For STM32F410Rx devices to output I2SCLK clock on MCO2 you should have
+  *        at last one of the SPI clocks enabled (SPI1, SPI2 or SPI5).
+  * @retval None
+  */
+void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv)
+{
+  GPIO_InitTypeDef GPIO_InitStruct;
+  /* Check the parameters */
+  assert_param(IS_RCC_MCO(RCC_MCOx));
+  assert_param(IS_RCC_MCODIV(RCC_MCODiv));
+  /* RCC_MCO1 */
+  if(RCC_MCOx == RCC_MCO1)
+  {
+    assert_param(IS_RCC_MCO1SOURCE(RCC_MCOSource));
+
+    /* MCO1 Clock Enable */
+    __MCO1_CLK_ENABLE();
+
+    /* Configure the MCO1 pin in alternate function mode */
+    GPIO_InitStruct.Pin = MCO1_PIN;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Alternate = GPIO_AF0_MCO;
+    HAL_GPIO_Init(MCO1_GPIO_PORT, &GPIO_InitStruct);
+
+    /* Mask MCO1 and MCO1PRE[2:0] bits then Select MCO1 clock source and prescaler */
+    MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO1 | RCC_CFGR_MCO1PRE), (RCC_MCOSource | RCC_MCODiv));
+
+   /* This RCC MCO1 enable feature is available only on STM32F410xx devices */
+#if defined(RCC_CFGR_MCO1EN)
+    __HAL_RCC_MCO1_ENABLE();
+#endif /* RCC_CFGR_MCO1EN */
+  }
+#if defined(RCC_CFGR_MCO2)
+  else
+  {
+    assert_param(IS_RCC_MCO2SOURCE(RCC_MCOSource));
+
+    /* MCO2 Clock Enable */
+    __MCO2_CLK_ENABLE();
+
+    /* Configure the MCO2 pin in alternate function mode */
+    GPIO_InitStruct.Pin = MCO2_PIN;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Alternate = GPIO_AF0_MCO;
+    HAL_GPIO_Init(MCO2_GPIO_PORT, &GPIO_InitStruct);
+
+    /* Mask MCO2 and MCO2PRE[2:0] bits then Select MCO2 clock source and prescaler */
+    MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO2 | RCC_CFGR_MCO2PRE), (RCC_MCOSource | (RCC_MCODiv << 3U)));
+
+   /* This RCC MCO2 enable feature is available only on STM32F410Rx devices */
+#if defined(RCC_CFGR_MCO2EN)
+    __HAL_RCC_MCO2_ENABLE();
+#endif /* RCC_CFGR_MCO2EN */
+  }
+#endif /* RCC_CFGR_MCO2 */
+}
+
+/**
+  * @brief  Enables the Clock Security System.
+  * @note   If a failure is detected on the HSE oscillator clock, this oscillator
+  *         is automatically disabled and an interrupt is generated to inform the
+  *         software about the failure (Clock Security System Interrupt, CSSI),
+  *         allowing the MCU to perform rescue operations. The CSSI is linked to
+  *         the Cortex-M4 NMI (Non-Maskable Interrupt) exception vector.
+  * @retval None
+  */
+void HAL_RCC_EnableCSS(void)
+{
+  *(__IO uint32_t *) RCC_CR_CSSON_BB = (uint32_t)ENABLE;
+}
+
+/**
+  * @brief  Disables the Clock Security System.
+  * @retval None
+  */
+void HAL_RCC_DisableCSS(void)
+{
+  *(__IO uint32_t *) RCC_CR_CSSON_BB = (uint32_t)DISABLE;
+}
+
+/**
+  * @brief  Returns the SYSCLK frequency
+  *
+  * @note   The system frequency computed by this function is not the real
+  *         frequency in the chip. It is calculated based on the predefined
+  *         constant and the selected clock source:
+  * @note     If SYSCLK source is HSI, function returns values based on HSI_VALUE(*)
+  * @note     If SYSCLK source is HSE, function returns values based on HSE_VALUE(**)
+  * @note     If SYSCLK source is PLL, function returns values based on HSE_VALUE(**)
+  *           or HSI_VALUE(*) multiplied/divided by the PLL factors.
+  * @note     (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
+  *               16 MHz) but the real value may vary depending on the variations
+  *               in voltage and temperature.
+  * @note     (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
+  *                25 MHz), user has to ensure that HSE_VALUE is same as the real
+  *                frequency of the crystal used. Otherwise, this function may
+  *                have wrong result.
+  *
+  * @note   The result of this function could be not correct when using fractional
+  *         value for HSE crystal.
+  *
+  * @note   This function can be used by the user application to compute the
+  *         baudrate for the communication peripherals or configure other parameters.
+  *
+  * @note   Each time SYSCLK changes, this function must be called to update the
+  *         right SYSCLK value. Otherwise, any configuration based on this function will be incorrect.
+  *
+  *
+  * @retval SYSCLK frequency
+  */
+__weak uint32_t HAL_RCC_GetSysClockFreq(void)
+{
+  uint32_t pllm = 0U, pllvco = 0U, pllp = 0U;
+  uint32_t sysclockfreq = 0U;
+
+  /* Get SYSCLK source -------------------------------------------------------*/
+  switch (RCC->CFGR & RCC_CFGR_SWS)
+  {
+    case RCC_CFGR_SWS_HSI:  /* HSI used as system clock source */
+    {
+      sysclockfreq = HSI_VALUE;
+       break;
+    }
+    case RCC_CFGR_SWS_HSE:  /* HSE used as system clock  source */
+    {
+      sysclockfreq = HSE_VALUE;
+      break;
+    }
+    case RCC_CFGR_SWS_PLL:  /* PLL used as system clock  source */
+    {
+      /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLLM) * PLLN
+      SYSCLK = PLL_VCO / PLLP */
+      pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
+      if(__HAL_RCC_GET_PLL_OSCSOURCE() != RCC_PLLSOURCE_HSI)
+      {
+        /* HSE used as PLL clock source */
+        pllvco = (uint32_t) ((((uint64_t) HSE_VALUE * ((uint64_t) ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos)))) / (uint64_t)pllm);
+      }
+      else
+      {
+        /* HSI used as PLL clock source */
+        pllvco = (uint32_t) ((((uint64_t) HSI_VALUE * ((uint64_t) ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos)))) / (uint64_t)pllm);
+      }
+      pllp = ((((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >> RCC_PLLCFGR_PLLP_Pos) + 1U) *2U);
+
+      sysclockfreq = pllvco/pllp;
+      break;
+    }
+    default:
+    {
+      sysclockfreq = HSI_VALUE;
+      break;
+    }
+  }
+  return sysclockfreq;
+}
+
+/**
+  * @brief  Returns the HCLK frequency
+  * @note   Each time HCLK changes, this function must be called to update the
+  *         right HCLK value. Otherwise, any configuration based on this function will be incorrect.
+  *
+  * @note   The SystemCoreClock CMSIS variable is used to store System Clock Frequency
+  *         and updated within this function
+  * @retval HCLK frequency
+  */
+uint32_t HAL_RCC_GetHCLKFreq(void)
+{
+  return SystemCoreClock;
+}
+
+/**
+  * @brief  Returns the PCLK1 frequency
+  * @note   Each time PCLK1 changes, this function must be called to update the
+  *         right PCLK1 value. Otherwise, any configuration based on this function will be incorrect.
+  * @retval PCLK1 frequency
+  */
+uint32_t HAL_RCC_GetPCLK1Freq(void)
+{
+  /* Get HCLK source and Compute PCLK1 frequency ---------------------------*/
+  return (HAL_RCC_GetHCLKFreq() >> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE1)>> RCC_CFGR_PPRE1_Pos]);
+}
+
+/**
+  * @brief  Returns the PCLK2 frequency
+  * @note   Each time PCLK2 changes, this function must be called to update the
+  *         right PCLK2 value. Otherwise, any configuration based on this function will be incorrect.
+  * @retval PCLK2 frequency
+  */
+uint32_t HAL_RCC_GetPCLK2Freq(void)
+{
+  /* Get HCLK source and Compute PCLK2 frequency ---------------------------*/
+  return (HAL_RCC_GetHCLKFreq()>> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE2)>> RCC_CFGR_PPRE2_Pos]);
+}
+
+/**
+  * @brief  Configures the RCC_OscInitStruct according to the internal
+  * RCC configuration registers.
+  * @param  RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that
+  * will be configured.
+  * @retval None
+  */
+__weak void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef  *RCC_OscInitStruct)
+{
+  /* Set all possible values for the Oscillator type parameter ---------------*/
+  RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_LSI;
+
+  /* Get the HSE configuration -----------------------------------------------*/
+  if((RCC->CR &RCC_CR_HSEBYP) == RCC_CR_HSEBYP)
+  {
+    RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS;
+  }
+  else if((RCC->CR &RCC_CR_HSEON) == RCC_CR_HSEON)
+  {
+    RCC_OscInitStruct->HSEState = RCC_HSE_ON;
+  }
+  else
+  {
+    RCC_OscInitStruct->HSEState = RCC_HSE_OFF;
+  }
+
+  /* Get the HSI configuration -----------------------------------------------*/
+  if((RCC->CR &RCC_CR_HSION) == RCC_CR_HSION)
+  {
+    RCC_OscInitStruct->HSIState = RCC_HSI_ON;
+  }
+  else
+  {
+    RCC_OscInitStruct->HSIState = RCC_HSI_OFF;
+  }
+
+  RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->CR &RCC_CR_HSITRIM) >> RCC_CR_HSITRIM_Pos);
+
+  /* Get the LSE configuration -----------------------------------------------*/
+  if((RCC->BDCR &RCC_BDCR_LSEBYP) == RCC_BDCR_LSEBYP)
+  {
+    RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS;
+  }
+  else if((RCC->BDCR &RCC_BDCR_LSEON) == RCC_BDCR_LSEON)
+  {
+    RCC_OscInitStruct->LSEState = RCC_LSE_ON;
+  }
+  else
+  {
+    RCC_OscInitStruct->LSEState = RCC_LSE_OFF;
+  }
+
+  /* Get the LSI configuration -----------------------------------------------*/
+  if((RCC->CSR &RCC_CSR_LSION) == RCC_CSR_LSION)
+  {
+    RCC_OscInitStruct->LSIState = RCC_LSI_ON;
+  }
+  else
+  {
+    RCC_OscInitStruct->LSIState = RCC_LSI_OFF;
+  }
+
+  /* Get the PLL configuration -----------------------------------------------*/
+  if((RCC->CR &RCC_CR_PLLON) == RCC_CR_PLLON)
+  {
+    RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON;
+  }
+  else
+  {
+    RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF;
+  }
+  RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC);
+  RCC_OscInitStruct->PLL.PLLM = (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM);
+  RCC_OscInitStruct->PLL.PLLN = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos);
+  RCC_OscInitStruct->PLL.PLLP = (uint32_t)((((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) + RCC_PLLCFGR_PLLP_0) << 1U) >> RCC_PLLCFGR_PLLP_Pos);
+  RCC_OscInitStruct->PLL.PLLQ = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLQ) >> RCC_PLLCFGR_PLLQ_Pos);
+}
+
+/**
+  * @brief  Configures the RCC_ClkInitStruct according to the internal
+  * RCC configuration registers.
+  * @param  RCC_ClkInitStruct pointer to an RCC_ClkInitTypeDef structure that
+  * will be configured.
+  * @param  pFLatency Pointer on the Flash Latency.
+  * @retval None
+  */
+void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef  *RCC_ClkInitStruct, uint32_t *pFLatency)
+{
+  /* Set all possible values for the Clock type parameter --------------------*/
+  RCC_ClkInitStruct->ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
+
+  /* Get the SYSCLK configuration --------------------------------------------*/
+  RCC_ClkInitStruct->SYSCLKSource = (uint32_t)(RCC->CFGR & RCC_CFGR_SW);
+
+  /* Get the HCLK configuration ----------------------------------------------*/
+  RCC_ClkInitStruct->AHBCLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_HPRE);
+
+  /* Get the APB1 configuration ----------------------------------------------*/
+  RCC_ClkInitStruct->APB1CLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_PPRE1);
+
+  /* Get the APB2 configuration ----------------------------------------------*/
+  RCC_ClkInitStruct->APB2CLKDivider = (uint32_t)((RCC->CFGR & RCC_CFGR_PPRE2) >> 3U);
+
+  /* Get the Flash Wait State (Latency) configuration ------------------------*/
+  *pFLatency = (uint32_t)(FLASH->ACR & FLASH_ACR_LATENCY);
+}
+
+/**
+  * @brief This function handles the RCC CSS interrupt request.
+  * @note This API should be called under the NMI_Handler().
+  * @retval None
+  */
+void HAL_RCC_NMI_IRQHandler(void)
+{
+  /* Check RCC CSSF flag  */
+  if(__HAL_RCC_GET_IT(RCC_IT_CSS))
+  {
+    /* RCC Clock Security System interrupt user callback */
+    HAL_RCC_CSSCallback();
+
+    /* Clear RCC CSS pending bit */
+    __HAL_RCC_CLEAR_IT(RCC_IT_CSS);
+  }
+}
+
+/**
+  * @brief  RCC Clock Security System interrupt callback
+  * @retval None
+  */
+__weak void HAL_RCC_CSSCallback(void)
+{
+  /* NOTE : This function Should not be modified, when the callback is needed,
+            the HAL_RCC_CSSCallback could be implemented in the user file
+   */
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* HAL_RCC_MODULE_ENABLED */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/