Mercurial > public > ostc4
diff Common/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc.h @ 160:e3ca52b8e7fa
Merge with FlipDisplay
| author | heinrichsweikamp |
|---|---|
| date | Thu, 07 Mar 2019 15:06:43 +0100 |
| parents | c78bcbd5deda |
| children |
line wrap: on
line diff
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/Common/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc.h Thu Mar 07 15:06:43 2019 +0100 @@ -0,0 +1,1480 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_rcc.h + * @author MCD Application Team + * @brief Header file of RCC HAL module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F4xx_HAL_RCC_H +#define __STM32F4xx_HAL_RCC_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f4xx_hal_def.h" + +/* Include RCC HAL Extended module */ +/* (include on top of file since RCC structures are defined in extended file) */ +#include "stm32f4xx_hal_rcc_ex.h" + +/** @addtogroup STM32F4xx_HAL_Driver + * @{ + */ + +/** @addtogroup RCC + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +/** @defgroup RCC_Exported_Types RCC Exported Types + * @{ + */ + +/** + * @brief RCC Internal/External Oscillator (HSE, HSI, LSE and LSI) configuration structure definition + */ +typedef struct +{ + uint32_t OscillatorType; /*!< The oscillators to be configured. + This parameter can be a value of @ref RCC_Oscillator_Type */ + + uint32_t HSEState; /*!< The new state of the HSE. + This parameter can be a value of @ref RCC_HSE_Config */ + + uint32_t LSEState; /*!< The new state of the LSE. + This parameter can be a value of @ref RCC_LSE_Config */ + + uint32_t HSIState; /*!< The new state of the HSI. + This parameter can be a value of @ref RCC_HSI_Config */ + + uint32_t HSICalibrationValue; /*!< The HSI calibration trimming value (default is RCC_HSICALIBRATION_DEFAULT). + This parameter must be a number between Min_Data = 0x00 and Max_Data = 0x1F */ + + uint32_t LSIState; /*!< The new state of the LSI. + This parameter can be a value of @ref RCC_LSI_Config */ + + RCC_PLLInitTypeDef PLL; /*!< PLL structure parameters */ +}RCC_OscInitTypeDef; + +/** + * @brief RCC System, AHB and APB busses clock configuration structure definition + */ +typedef struct +{ + uint32_t ClockType; /*!< The clock to be configured. + This parameter can be a value of @ref RCC_System_Clock_Type */ + + uint32_t SYSCLKSource; /*!< The clock source (SYSCLKS) used as system clock. + This parameter can be a value of @ref RCC_System_Clock_Source */ + + uint32_t AHBCLKDivider; /*!< The AHB clock (HCLK) divider. This clock is derived from the system clock (SYSCLK). + This parameter can be a value of @ref RCC_AHB_Clock_Source */ + + uint32_t APB1CLKDivider; /*!< The APB1 clock (PCLK1) divider. This clock is derived from the AHB clock (HCLK). + This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */ + + uint32_t APB2CLKDivider; /*!< The APB2 clock (PCLK2) divider. This clock is derived from the AHB clock (HCLK). + This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */ + +}RCC_ClkInitTypeDef; + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup RCC_Exported_Constants RCC Exported Constants + * @{ + */ + +/** @defgroup RCC_Oscillator_Type Oscillator Type + * @{ + */ +#define RCC_OSCILLATORTYPE_NONE 0x00000000U +#define RCC_OSCILLATORTYPE_HSE 0x00000001U +#define RCC_OSCILLATORTYPE_HSI 0x00000002U +#define RCC_OSCILLATORTYPE_LSE 0x00000004U +#define RCC_OSCILLATORTYPE_LSI 0x00000008U +/** + * @} + */ + +/** @defgroup RCC_HSE_Config HSE Config + * @{ + */ +#define RCC_HSE_OFF 0x00000000U +#define RCC_HSE_ON RCC_CR_HSEON +#define RCC_HSE_BYPASS ((uint32_t)(RCC_CR_HSEBYP | RCC_CR_HSEON)) +/** + * @} + */ + +/** @defgroup RCC_LSE_Config LSE Config + * @{ + */ +#define RCC_LSE_OFF 0x00000000U +#define RCC_LSE_ON RCC_BDCR_LSEON +#define RCC_LSE_BYPASS ((uint32_t)(RCC_BDCR_LSEBYP | RCC_BDCR_LSEON)) +/** + * @} + */ + +/** @defgroup RCC_HSI_Config HSI Config + * @{ + */ +#define RCC_HSI_OFF ((uint8_t)0x00) +#define RCC_HSI_ON ((uint8_t)0x01) + +#define RCC_HSICALIBRATION_DEFAULT 0x10U /* Default HSI calibration trimming value */ +/** + * @} + */ + +/** @defgroup RCC_LSI_Config LSI Config + * @{ + */ +#define RCC_LSI_OFF ((uint8_t)0x00) +#define RCC_LSI_ON ((uint8_t)0x01) +/** + * @} + */ + +/** @defgroup RCC_PLL_Config PLL Config + * @{ + */ +#define RCC_PLL_NONE ((uint8_t)0x00) +#define RCC_PLL_OFF ((uint8_t)0x01) +#define RCC_PLL_ON ((uint8_t)0x02) +/** + * @} + */ + +/** @defgroup RCC_PLLP_Clock_Divider PLLP Clock Divider + * @{ + */ +#define RCC_PLLP_DIV2 0x00000002U +#define RCC_PLLP_DIV4 0x00000004U +#define RCC_PLLP_DIV6 0x00000006U +#define RCC_PLLP_DIV8 0x00000008U +/** + * @} + */ + +/** @defgroup RCC_PLL_Clock_Source PLL Clock Source + * @{ + */ +#define RCC_PLLSOURCE_HSI RCC_PLLCFGR_PLLSRC_HSI +#define RCC_PLLSOURCE_HSE RCC_PLLCFGR_PLLSRC_HSE +/** + * @} + */ + +/** @defgroup RCC_System_Clock_Type System Clock Type + * @{ + */ +#define RCC_CLOCKTYPE_SYSCLK 0x00000001U +#define RCC_CLOCKTYPE_HCLK 0x00000002U +#define RCC_CLOCKTYPE_PCLK1 0x00000004U +#define RCC_CLOCKTYPE_PCLK2 0x00000008U +/** + * @} + */ + +/** @defgroup RCC_System_Clock_Source System Clock Source + * @note The RCC_SYSCLKSOURCE_PLLRCLK parameter is available only for + * STM32F446xx devices. + * @{ + */ +#define RCC_SYSCLKSOURCE_HSI RCC_CFGR_SW_HSI +#define RCC_SYSCLKSOURCE_HSE RCC_CFGR_SW_HSE +#define RCC_SYSCLKSOURCE_PLLCLK RCC_CFGR_SW_PLL +#define RCC_SYSCLKSOURCE_PLLRCLK ((uint32_t)(RCC_CFGR_SW_0 | RCC_CFGR_SW_1)) +/** + * @} + */ + +/** @defgroup RCC_System_Clock_Source_Status System Clock Source Status + * @note The RCC_SYSCLKSOURCE_STATUS_PLLRCLK parameter is available only for + * STM32F446xx devices. + * @{ + */ +#define RCC_SYSCLKSOURCE_STATUS_HSI RCC_CFGR_SWS_HSI /*!< HSI used as system clock */ +#define RCC_SYSCLKSOURCE_STATUS_HSE RCC_CFGR_SWS_HSE /*!< HSE used as system clock */ +#define RCC_SYSCLKSOURCE_STATUS_PLLCLK RCC_CFGR_SWS_PLL /*!< PLL used as system clock */ +#define RCC_SYSCLKSOURCE_STATUS_PLLRCLK ((uint32_t)(RCC_CFGR_SWS_0 | RCC_CFGR_SWS_1)) /*!< PLLR used as system clock */ +/** + * @} + */ + +/** @defgroup RCC_AHB_Clock_Source AHB Clock Source + * @{ + */ +#define RCC_SYSCLK_DIV1 RCC_CFGR_HPRE_DIV1 +#define RCC_SYSCLK_DIV2 RCC_CFGR_HPRE_DIV2 +#define RCC_SYSCLK_DIV4 RCC_CFGR_HPRE_DIV4 +#define RCC_SYSCLK_DIV8 RCC_CFGR_HPRE_DIV8 +#define RCC_SYSCLK_DIV16 RCC_CFGR_HPRE_DIV16 +#define RCC_SYSCLK_DIV64 RCC_CFGR_HPRE_DIV64 +#define RCC_SYSCLK_DIV128 RCC_CFGR_HPRE_DIV128 +#define RCC_SYSCLK_DIV256 RCC_CFGR_HPRE_DIV256 +#define RCC_SYSCLK_DIV512 RCC_CFGR_HPRE_DIV512 +/** + * @} + */ + +/** @defgroup RCC_APB1_APB2_Clock_Source APB1/APB2 Clock Source + * @{ + */ +#define RCC_HCLK_DIV1 RCC_CFGR_PPRE1_DIV1 +#define RCC_HCLK_DIV2 RCC_CFGR_PPRE1_DIV2 +#define RCC_HCLK_DIV4 RCC_CFGR_PPRE1_DIV4 +#define RCC_HCLK_DIV8 RCC_CFGR_PPRE1_DIV8 +#define RCC_HCLK_DIV16 RCC_CFGR_PPRE1_DIV16 +/** + * @} + */ + +/** @defgroup RCC_RTC_Clock_Source RTC Clock Source + * @{ + */ +#define RCC_RTCCLKSOURCE_NO_CLK 0x00000000U +#define RCC_RTCCLKSOURCE_LSE 0x00000100U +#define RCC_RTCCLKSOURCE_LSI 0x00000200U +#define RCC_RTCCLKSOURCE_HSE_DIVX 0x00000300U +#define RCC_RTCCLKSOURCE_HSE_DIV2 0x00020300U +#define RCC_RTCCLKSOURCE_HSE_DIV3 0x00030300U +#define RCC_RTCCLKSOURCE_HSE_DIV4 0x00040300U +#define RCC_RTCCLKSOURCE_HSE_DIV5 0x00050300U +#define RCC_RTCCLKSOURCE_HSE_DIV6 0x00060300U +#define RCC_RTCCLKSOURCE_HSE_DIV7 0x00070300U +#define RCC_RTCCLKSOURCE_HSE_DIV8 0x00080300U +#define RCC_RTCCLKSOURCE_HSE_DIV9 0x00090300U +#define RCC_RTCCLKSOURCE_HSE_DIV10 0x000A0300U +#define RCC_RTCCLKSOURCE_HSE_DIV11 0x000B0300U +#define RCC_RTCCLKSOURCE_HSE_DIV12 0x000C0300U +#define RCC_RTCCLKSOURCE_HSE_DIV13 0x000D0300U +#define RCC_RTCCLKSOURCE_HSE_DIV14 0x000E0300U +#define RCC_RTCCLKSOURCE_HSE_DIV15 0x000F0300U +#define RCC_RTCCLKSOURCE_HSE_DIV16 0x00100300U +#define RCC_RTCCLKSOURCE_HSE_DIV17 0x00110300U +#define RCC_RTCCLKSOURCE_HSE_DIV18 0x00120300U +#define RCC_RTCCLKSOURCE_HSE_DIV19 0x00130300U +#define RCC_RTCCLKSOURCE_HSE_DIV20 0x00140300U +#define RCC_RTCCLKSOURCE_HSE_DIV21 0x00150300U +#define RCC_RTCCLKSOURCE_HSE_DIV22 0x00160300U +#define RCC_RTCCLKSOURCE_HSE_DIV23 0x00170300U +#define RCC_RTCCLKSOURCE_HSE_DIV24 0x00180300U +#define RCC_RTCCLKSOURCE_HSE_DIV25 0x00190300U +#define RCC_RTCCLKSOURCE_HSE_DIV26 0x001A0300U +#define RCC_RTCCLKSOURCE_HSE_DIV27 0x001B0300U +#define RCC_RTCCLKSOURCE_HSE_DIV28 0x001C0300U +#define RCC_RTCCLKSOURCE_HSE_DIV29 0x001D0300U +#define RCC_RTCCLKSOURCE_HSE_DIV30 0x001E0300U +#define RCC_RTCCLKSOURCE_HSE_DIV31 0x001F0300U +/** + * @} + */ + +/** @defgroup RCC_MCO_Index MCO Index + * @{ + */ +#define RCC_MCO1 0x00000000U +#define RCC_MCO2 0x00000001U +/** + * @} + */ + +/** @defgroup RCC_MCO1_Clock_Source MCO1 Clock Source + * @{ + */ +#define RCC_MCO1SOURCE_HSI 0x00000000U +#define RCC_MCO1SOURCE_LSE RCC_CFGR_MCO1_0 +#define RCC_MCO1SOURCE_HSE RCC_CFGR_MCO1_1 +#define RCC_MCO1SOURCE_PLLCLK RCC_CFGR_MCO1 +/** + * @} + */ + +/** @defgroup RCC_MCOx_Clock_Prescaler MCOx Clock Prescaler + * @{ + */ +#define RCC_MCODIV_1 0x00000000U +#define RCC_MCODIV_2 RCC_CFGR_MCO1PRE_2 +#define RCC_MCODIV_3 ((uint32_t)RCC_CFGR_MCO1PRE_0 | RCC_CFGR_MCO1PRE_2) +#define RCC_MCODIV_4 ((uint32_t)RCC_CFGR_MCO1PRE_1 | RCC_CFGR_MCO1PRE_2) +#define RCC_MCODIV_5 RCC_CFGR_MCO1PRE +/** + * @} + */ + +/** @defgroup RCC_Interrupt Interrupts + * @{ + */ +#define RCC_IT_LSIRDY ((uint8_t)0x01) +#define RCC_IT_LSERDY ((uint8_t)0x02) +#define RCC_IT_HSIRDY ((uint8_t)0x04) +#define RCC_IT_HSERDY ((uint8_t)0x08) +#define RCC_IT_PLLRDY ((uint8_t)0x10) +#define RCC_IT_PLLI2SRDY ((uint8_t)0x20) +#define RCC_IT_CSS ((uint8_t)0x80) +/** + * @} + */ + +/** @defgroup RCC_Flag Flags + * Elements values convention: 0XXYYYYYb + * - YYYYY : Flag position in the register + * - 0XX : Register index + * - 01: CR register + * - 10: BDCR register + * - 11: CSR register + * @{ + */ +/* Flags in the CR register */ +#define RCC_FLAG_HSIRDY ((uint8_t)0x21) +#define RCC_FLAG_HSERDY ((uint8_t)0x31) +#define RCC_FLAG_PLLRDY ((uint8_t)0x39) +#define RCC_FLAG_PLLI2SRDY ((uint8_t)0x3B) + +/* Flags in the BDCR register */ +#define RCC_FLAG_LSERDY ((uint8_t)0x41) + +/* Flags in the CSR register */ +#define RCC_FLAG_LSIRDY ((uint8_t)0x61) +#define RCC_FLAG_BORRST ((uint8_t)0x79) +#define RCC_FLAG_PINRST ((uint8_t)0x7A) +#define RCC_FLAG_PORRST ((uint8_t)0x7B) +#define RCC_FLAG_SFTRST ((uint8_t)0x7C) +#define RCC_FLAG_IWDGRST ((uint8_t)0x7D) +#define RCC_FLAG_WWDGRST ((uint8_t)0x7E) +#define RCC_FLAG_LPWRRST ((uint8_t)0x7F) +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup RCC_Exported_Macros RCC Exported Macros + * @{ + */ + +/** @defgroup RCC_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable + * @brief Enable or disable the AHB1 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#define __HAL_RCC_GPIOA_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOAEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOAEN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_GPIOB_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOBEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOBEN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_GPIOC_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_GPIOH_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOHEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOHEN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_DMA1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_DMA2_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_GPIOA_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOAEN)) +#define __HAL_RCC_GPIOB_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOBEN)) +#define __HAL_RCC_GPIOC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOCEN)) +#define __HAL_RCC_GPIOH_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOHEN)) +#define __HAL_RCC_DMA1_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_DMA1EN)) +#define __HAL_RCC_DMA2_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_DMA2EN)) +/** + * @} + */ + +/** @defgroup RCC_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enable Disable Status + * @brief Get the enable or disable status of the AHB1 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#define __HAL_RCC_GPIOA_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOAEN)) != RESET) +#define __HAL_RCC_GPIOB_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOBEN)) != RESET) +#define __HAL_RCC_GPIOC_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOCEN)) != RESET) +#define __HAL_RCC_GPIOH_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOHEN)) != RESET) +#define __HAL_RCC_DMA1_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_DMA1EN)) != RESET) +#define __HAL_RCC_DMA2_IS_CLK_ENABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_DMA2EN)) != RESET) + +#define __HAL_RCC_GPIOA_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOAEN)) == RESET) +#define __HAL_RCC_GPIOB_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOBEN)) == RESET) +#define __HAL_RCC_GPIOC_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOCEN)) == RESET) +#define __HAL_RCC_GPIOH_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_GPIOHEN)) == RESET) +#define __HAL_RCC_DMA1_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_DMA1EN)) == RESET) +#define __HAL_RCC_DMA2_IS_CLK_DISABLED() ((RCC->AHB1ENR &(RCC_AHB1ENR_DMA2EN)) == RESET) +/** + * @} + */ + +/** @defgroup RCC_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable + * @brief Enable or disable the Low Speed APB (APB1) peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#define __HAL_RCC_TIM5_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM5EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM5EN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_WWDG_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_SPI2_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI2EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI2EN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_USART2_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_USART2EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_USART2EN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_I2C1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_I2C2_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C2EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C2EN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_PWR_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM5_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM5EN)) +#define __HAL_RCC_WWDG_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_WWDGEN)) +#define __HAL_RCC_SPI2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI2EN)) +#define __HAL_RCC_USART2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_USART2EN)) +#define __HAL_RCC_I2C1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C1EN)) +#define __HAL_RCC_I2C2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C2EN)) +#define __HAL_RCC_PWR_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_PWREN)) +/** + * @} + */ + +/** @defgroup RCC_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status + * @brief Get the enable or disable status of the APB1 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#define __HAL_RCC_TIM5_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM5EN)) != RESET) +#define __HAL_RCC_WWDG_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) != RESET) +#define __HAL_RCC_SPI2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI2EN)) != RESET) +#define __HAL_RCC_USART2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART2EN)) != RESET) +#define __HAL_RCC_I2C1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) != RESET) +#define __HAL_RCC_I2C2_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C2EN)) != RESET) +#define __HAL_RCC_PWR_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) != RESET) + +#define __HAL_RCC_TIM5_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM5EN)) == RESET) +#define __HAL_RCC_WWDG_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) == RESET) +#define __HAL_RCC_SPI2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_SPI2EN)) == RESET) +#define __HAL_RCC_USART2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_USART2EN)) == RESET) +#define __HAL_RCC_I2C1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) == RESET) +#define __HAL_RCC_I2C2_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C2EN)) == RESET) +#define __HAL_RCC_PWR_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) == RESET) +/** + * @} + */ + +/** @defgroup RCC_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable + * @brief Enable or disable the High Speed APB (APB2) peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#define __HAL_RCC_TIM1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_USART1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_USART6_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_USART6EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART6EN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_ADC1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_SPI1_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_SYSCFG_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_TIM9_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM9EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM9EN);\ + UNUSED(tmpreg); \ + } while(0U) +#define __HAL_RCC_TIM11_CLK_ENABLE() do { \ + __IO uint32_t tmpreg = 0x00U; \ + SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM11EN);\ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM11EN);\ + UNUSED(tmpreg); \ + } while(0U) + +#define __HAL_RCC_TIM1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM1EN)) +#define __HAL_RCC_USART1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_USART1EN)) +#define __HAL_RCC_USART6_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_USART6EN)) +#define __HAL_RCC_ADC1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC1EN)) +#define __HAL_RCC_SPI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI1EN)) +#define __HAL_RCC_SYSCFG_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SYSCFGEN)) +#define __HAL_RCC_TIM9_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM9EN)) +#define __HAL_RCC_TIM11_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM11EN)) +/** + * @} + */ + +/** @defgroup RCC_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status + * @brief Get the enable or disable status of the APB2 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#define __HAL_RCC_TIM1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) != RESET) +#define __HAL_RCC_USART1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) != RESET) +#define __HAL_RCC_USART6_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART6EN)) != RESET) +#define __HAL_RCC_ADC1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) != RESET) +#define __HAL_RCC_SPI1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) != RESET) +#define __HAL_RCC_SYSCFG_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SYSCFGEN)) != RESET) +#define __HAL_RCC_TIM9_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM9EN)) != RESET) +#define __HAL_RCC_TIM11_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM11EN)) != RESET) + +#define __HAL_RCC_TIM1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) == RESET) +#define __HAL_RCC_USART1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) == RESET) +#define __HAL_RCC_USART6_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART6EN)) == RESET) +#define __HAL_RCC_ADC1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) == RESET) +#define __HAL_RCC_SPI1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) == RESET) +#define __HAL_RCC_SYSCFG_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SYSCFGEN)) == RESET) +#define __HAL_RCC_TIM9_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM9EN)) == RESET) +#define __HAL_RCC_TIM11_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM11EN)) == RESET) +/** + * @} + */ + +/** @defgroup RCC_AHB1_Force_Release_Reset AHB1 Force Release Reset + * @brief Force or release AHB1 peripheral reset. + * @{ + */ +#define __HAL_RCC_AHB1_FORCE_RESET() (RCC->AHB1RSTR = 0xFFFFFFFFU) +#define __HAL_RCC_GPIOA_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOARST)) +#define __HAL_RCC_GPIOB_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOBRST)) +#define __HAL_RCC_GPIOC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOCRST)) +#define __HAL_RCC_GPIOH_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOHRST)) +#define __HAL_RCC_DMA1_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_DMA1RST)) +#define __HAL_RCC_DMA2_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_DMA2RST)) + +#define __HAL_RCC_AHB1_RELEASE_RESET() (RCC->AHB1RSTR = 0x00U) +#define __HAL_RCC_GPIOA_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOARST)) +#define __HAL_RCC_GPIOB_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOBRST)) +#define __HAL_RCC_GPIOC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOCRST)) +#define __HAL_RCC_GPIOH_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOHRST)) +#define __HAL_RCC_DMA1_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_DMA1RST)) +#define __HAL_RCC_DMA2_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_DMA2RST)) +/** + * @} + */ + +/** @defgroup RCC_APB1_Force_Release_Reset APB1 Force Release Reset + * @brief Force or release APB1 peripheral reset. + * @{ + */ +#define __HAL_RCC_APB1_FORCE_RESET() (RCC->APB1RSTR = 0xFFFFFFFFU) +#define __HAL_RCC_TIM5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM5RST)) +#define __HAL_RCC_WWDG_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_WWDGRST)) +#define __HAL_RCC_SPI2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI2RST)) +#define __HAL_RCC_USART2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART2RST)) +#define __HAL_RCC_I2C1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C1RST)) +#define __HAL_RCC_I2C2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C2RST)) +#define __HAL_RCC_PWR_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_PWRRST)) + +#define __HAL_RCC_APB1_RELEASE_RESET() (RCC->APB1RSTR = 0x00U) +#define __HAL_RCC_TIM5_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM5RST)) +#define __HAL_RCC_WWDG_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_WWDGRST)) +#define __HAL_RCC_SPI2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI2RST)) +#define __HAL_RCC_USART2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_USART2RST)) +#define __HAL_RCC_I2C1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C1RST)) +#define __HAL_RCC_I2C2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C2RST)) +#define __HAL_RCC_PWR_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_PWRRST)) +/** + * @} + */ + +/** @defgroup RCC_APB2_Force_Release_Reset APB2 Force Release Reset + * @brief Force or release APB2 peripheral reset. + * @{ + */ +#define __HAL_RCC_APB2_FORCE_RESET() (RCC->APB2RSTR = 0xFFFFFFFFU) +#define __HAL_RCC_TIM1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM1RST)) +#define __HAL_RCC_USART1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_USART1RST)) +#define __HAL_RCC_USART6_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_USART6RST)) +#define __HAL_RCC_ADC_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_ADCRST)) +#define __HAL_RCC_SPI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI1RST)) +#define __HAL_RCC_SYSCFG_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SYSCFGRST)) +#define __HAL_RCC_TIM9_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM9RST)) +#define __HAL_RCC_TIM11_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM11RST)) + +#define __HAL_RCC_APB2_RELEASE_RESET() (RCC->APB2RSTR = 0x00U) +#define __HAL_RCC_TIM1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM1RST)) +#define __HAL_RCC_USART1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_USART1RST)) +#define __HAL_RCC_USART6_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_USART6RST)) +#define __HAL_RCC_ADC_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_ADCRST)) +#define __HAL_RCC_SPI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI1RST)) +#define __HAL_RCC_SYSCFG_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SYSCFGRST)) +#define __HAL_RCC_TIM9_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM9RST)) +#define __HAL_RCC_TIM11_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM11RST)) +/** + * @} + */ + +/** @defgroup RCC_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable + * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode. + * @note Peripheral clock gating in SLEEP mode can be used to further reduce + * power consumption. + * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. + * @note By default, all peripheral clocks are enabled during SLEEP mode. + * @{ + */ +#define __HAL_RCC_GPIOA_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOALPEN)) +#define __HAL_RCC_GPIOB_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOBLPEN)) +#define __HAL_RCC_GPIOC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOCLPEN)) +#define __HAL_RCC_GPIOH_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOHLPEN)) +#define __HAL_RCC_DMA1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_DMA1LPEN)) +#define __HAL_RCC_DMA2_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_DMA2LPEN)) + +#define __HAL_RCC_GPIOA_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOALPEN)) +#define __HAL_RCC_GPIOB_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOBLPEN)) +#define __HAL_RCC_GPIOC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOCLPEN)) +#define __HAL_RCC_GPIOH_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOHLPEN)) +#define __HAL_RCC_DMA1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_DMA1LPEN)) +#define __HAL_RCC_DMA2_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_DMA2LPEN)) +/** + * @} + */ + +/** @defgroup RCC_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable + * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode. + * @note Peripheral clock gating in SLEEP mode can be used to further reduce + * power consumption. + * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. + * @note By default, all peripheral clocks are enabled during SLEEP mode. + * @{ + */ +#define __HAL_RCC_TIM5_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM5LPEN)) +#define __HAL_RCC_WWDG_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_WWDGLPEN)) +#define __HAL_RCC_SPI2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI2LPEN)) +#define __HAL_RCC_USART2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_USART2LPEN)) +#define __HAL_RCC_I2C1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C1LPEN)) +#define __HAL_RCC_I2C2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C2LPEN)) +#define __HAL_RCC_PWR_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_PWRLPEN)) + +#define __HAL_RCC_TIM5_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM5LPEN)) +#define __HAL_RCC_WWDG_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_WWDGLPEN)) +#define __HAL_RCC_SPI2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI2LPEN)) +#define __HAL_RCC_USART2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_USART2LPEN)) +#define __HAL_RCC_I2C1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C1LPEN)) +#define __HAL_RCC_I2C2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C2LPEN)) +#define __HAL_RCC_PWR_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_PWRLPEN)) +/** + * @} + */ + +/** @defgroup RCC_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable + * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode. + * @note Peripheral clock gating in SLEEP mode can be used to further reduce + * power consumption. + * @note After wake-up from SLEEP mode, the peripheral clock is enabled again. + * @note By default, all peripheral clocks are enabled during SLEEP mode. + * @{ + */ +#define __HAL_RCC_TIM1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM1LPEN)) +#define __HAL_RCC_USART1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_USART1LPEN)) +#define __HAL_RCC_USART6_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_USART6LPEN)) +#define __HAL_RCC_ADC1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC1LPEN)) +#define __HAL_RCC_SPI1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI1LPEN)) +#define __HAL_RCC_SYSCFG_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SYSCFGLPEN)) +#define __HAL_RCC_TIM9_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM9LPEN)) +#define __HAL_RCC_TIM11_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM11LPEN)) + +#define __HAL_RCC_TIM1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM1LPEN)) +#define __HAL_RCC_USART1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_USART1LPEN)) +#define __HAL_RCC_USART6_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_USART6LPEN)) +#define __HAL_RCC_ADC1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC1LPEN)) +#define __HAL_RCC_SPI1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI1LPEN)) +#define __HAL_RCC_SYSCFG_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SYSCFGLPEN)) +#define __HAL_RCC_TIM9_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM9LPEN)) +#define __HAL_RCC_TIM11_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM11LPEN)) +/** + * @} + */ + +/** @defgroup RCC_HSI_Configuration HSI Configuration + * @{ + */ + +/** @brief Macros to enable or disable the Internal High Speed oscillator (HSI). + * @note The HSI is stopped by hardware when entering STOP and STANDBY modes. + * It is used (enabled by hardware) as system clock source after startup + * from Reset, wake-up from STOP and STANDBY mode, or in case of failure + * of the HSE used directly or indirectly as system clock (if the Clock + * Security System CSS is enabled). + * @note HSI can not be stopped if it is used as system clock source. In this case, + * you have to select another source of the system clock then stop the HSI. + * @note After enabling the HSI, the application software should wait on HSIRDY + * flag to be set indicating that HSI clock is stable and can be used as + * system clock source. + * This parameter can be: ENABLE or DISABLE. + * @note When the HSI is stopped, HSIRDY flag goes low after 6 HSI oscillator + * clock cycles. + */ +#define __HAL_RCC_HSI_ENABLE() (*(__IO uint32_t *) RCC_CR_HSION_BB = ENABLE) +#define __HAL_RCC_HSI_DISABLE() (*(__IO uint32_t *) RCC_CR_HSION_BB = DISABLE) + +/** @brief Macro to adjust the Internal High Speed oscillator (HSI) calibration value. + * @note The calibration is used to compensate for the variations in voltage + * and temperature that influence the frequency of the internal HSI RC. + * @param __HSICalibrationValue__ specifies the calibration trimming value. + * (default is RCC_HSICALIBRATION_DEFAULT). + * This parameter must be a number between 0 and 0x1F. + */ +#define __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(__HSICalibrationValue__) (MODIFY_REG(RCC->CR,\ + RCC_CR_HSITRIM, (uint32_t)(__HSICalibrationValue__) << RCC_CR_HSITRIM_Pos)) +/** + * @} + */ + +/** @defgroup RCC_LSI_Configuration LSI Configuration + * @{ + */ + +/** @brief Macros to enable or disable the Internal Low Speed oscillator (LSI). + * @note After enabling the LSI, the application software should wait on + * LSIRDY flag to be set indicating that LSI clock is stable and can + * be used to clock the IWDG and/or the RTC. + * @note LSI can not be disabled if the IWDG is running. + * @note When the LSI is stopped, LSIRDY flag goes low after 6 LSI oscillator + * clock cycles. + */ +#define __HAL_RCC_LSI_ENABLE() (*(__IO uint32_t *) RCC_CSR_LSION_BB = ENABLE) +#define __HAL_RCC_LSI_DISABLE() (*(__IO uint32_t *) RCC_CSR_LSION_BB = DISABLE) +/** + * @} + */ + +/** @defgroup RCC_HSE_Configuration HSE Configuration + * @{ + */ + +/** + * @brief Macro to configure the External High Speed oscillator (HSE). + * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not supported by this macro. + * User should request a transition to HSE Off first and then HSE On or HSE Bypass. + * @note After enabling the HSE (RCC_HSE_ON or RCC_HSE_Bypass), the application + * software should wait on HSERDY flag to be set indicating that HSE clock + * is stable and can be used to clock the PLL and/or system clock. + * @note HSE state can not be changed if it is used directly or through the + * PLL as system clock. In this case, you have to select another source + * of the system clock then change the HSE state (ex. disable it). + * @note The HSE is stopped by hardware when entering STOP and STANDBY modes. + * @note This function reset the CSSON bit, so if the clock security system(CSS) + * was previously enabled you have to enable it again after calling this + * function. + * @param __STATE__ specifies the new state of the HSE. + * This parameter can be one of the following values: + * @arg RCC_HSE_OFF: turn OFF the HSE oscillator, HSERDY flag goes low after + * 6 HSE oscillator clock cycles. + * @arg RCC_HSE_ON: turn ON the HSE oscillator. + * @arg RCC_HSE_BYPASS: HSE oscillator bypassed with external clock. + */ +#define __HAL_RCC_HSE_CONFIG(__STATE__) \ + do { \ + if ((__STATE__) == RCC_HSE_ON) \ + { \ + SET_BIT(RCC->CR, RCC_CR_HSEON); \ + } \ + else if ((__STATE__) == RCC_HSE_BYPASS) \ + { \ + SET_BIT(RCC->CR, RCC_CR_HSEBYP); \ + SET_BIT(RCC->CR, RCC_CR_HSEON); \ + } \ + else \ + { \ + CLEAR_BIT(RCC->CR, RCC_CR_HSEON); \ + CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); \ + } \ + } while(0U) +/** + * @} + */ + +/** @defgroup RCC_LSE_Configuration LSE Configuration + * @{ + */ + +/** + * @brief Macro to configure the External Low Speed oscillator (LSE). + * @note Transition LSE Bypass to LSE On and LSE On to LSE Bypass are not supported by this macro. + * User should request a transition to LSE Off first and then LSE On or LSE Bypass. + * @note As the LSE is in the Backup domain and write access is denied to + * this domain after reset, you have to enable write access using + * HAL_PWR_EnableBkUpAccess() function before to configure the LSE + * (to be done once after reset). + * @note After enabling the LSE (RCC_LSE_ON or RCC_LSE_BYPASS), the application + * software should wait on LSERDY flag to be set indicating that LSE clock + * is stable and can be used to clock the RTC. + * @param __STATE__ specifies the new state of the LSE. + * This parameter can be one of the following values: + * @arg RCC_LSE_OFF: turn OFF the LSE oscillator, LSERDY flag goes low after + * 6 LSE oscillator clock cycles. + * @arg RCC_LSE_ON: turn ON the LSE oscillator. + * @arg RCC_LSE_BYPASS: LSE oscillator bypassed with external clock. + */ +#define __HAL_RCC_LSE_CONFIG(__STATE__) \ + do { \ + if((__STATE__) == RCC_LSE_ON) \ + { \ + SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ + } \ + else if((__STATE__) == RCC_LSE_BYPASS) \ + { \ + SET_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \ + SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ + } \ + else \ + { \ + CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEON); \ + CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \ + } \ + } while(0U) +/** + * @} + */ + +/** @defgroup RCC_Internal_RTC_Clock_Configuration RTC Clock Configuration + * @{ + */ + +/** @brief Macros to enable or disable the RTC clock. + * @note These macros must be used only after the RTC clock source was selected. + */ +#define __HAL_RCC_RTC_ENABLE() (*(__IO uint32_t *) RCC_BDCR_RTCEN_BB = ENABLE) +#define __HAL_RCC_RTC_DISABLE() (*(__IO uint32_t *) RCC_BDCR_RTCEN_BB = DISABLE) + +/** @brief Macros to configure the RTC clock (RTCCLK). + * @note As the RTC clock configuration bits are in the Backup domain and write + * access is denied to this domain after reset, you have to enable write + * access using the Power Backup Access macro before to configure + * the RTC clock source (to be done once after reset). + * @note Once the RTC clock is configured it can't be changed unless the + * Backup domain is reset using __HAL_RCC_BackupReset_RELEASE() macro, or by + * a Power On Reset (POR). + * @param __RTCCLKSource__ specifies the RTC clock source. + * This parameter can be one of the following values: + @arg @ref RCC_RTCCLKSOURCE_NO_CLK: No clock selected as RTC clock. + * @arg @ref RCC_RTCCLKSOURCE_LSE: LSE selected as RTC clock. + * @arg @ref RCC_RTCCLKSOURCE_LSI: LSI selected as RTC clock. + * @arg @ref RCC_RTCCLKSOURCE_HSE_DIVX: HSE clock divided by x selected + * as RTC clock, where x:[2,31] + * @note If the LSE or LSI is used as RTC clock source, the RTC continues to + * work in STOP and STANDBY modes, and can be used as wake-up source. + * However, when the HSE clock is used as RTC clock source, the RTC + * cannot be used in STOP and STANDBY modes. + * @note The maximum input clock frequency for RTC is 1MHz (when using HSE as + * RTC clock source). + */ +#define __HAL_RCC_RTC_CLKPRESCALER(__RTCCLKSource__) (((__RTCCLKSource__) & RCC_BDCR_RTCSEL) == RCC_BDCR_RTCSEL) ? \ + MODIFY_REG(RCC->CFGR, RCC_CFGR_RTCPRE, ((__RTCCLKSource__) & 0xFFFFCFFU)) : CLEAR_BIT(RCC->CFGR, RCC_CFGR_RTCPRE) + +#define __HAL_RCC_RTC_CONFIG(__RTCCLKSource__) do { __HAL_RCC_RTC_CLKPRESCALER(__RTCCLKSource__); \ + RCC->BDCR |= ((__RTCCLKSource__) & 0x00000FFFU); \ + } while(0U) + +/** @brief Macro to get the RTC clock source. + * @retval The clock source can be one of the following values: + * @arg @ref RCC_RTCCLKSOURCE_NO_CLK No clock selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_LSE LSE selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_LSI LSI selected as RTC clock + * @arg @ref RCC_RTCCLKSOURCE_HSE_DIVX HSE divided by X selected as RTC clock (X can be retrieved thanks to @ref __HAL_RCC_GET_RTC_HSE_PRESCALER() + */ +#define __HAL_RCC_GET_RTC_SOURCE() (READ_BIT(RCC->BDCR, RCC_BDCR_RTCSEL)) + +/** + * @brief Get the RTC and HSE clock divider (RTCPRE). + * @retval Returned value can be one of the following values: + * @arg @ref RCC_RTCCLKSOURCE_HSE_DIVX: HSE clock divided by x selected + * as RTC clock, where x:[2,31] + */ +#define __HAL_RCC_GET_RTC_HSE_PRESCALER() (READ_BIT(RCC->CFGR, RCC_CFGR_RTCPRE) | RCC_BDCR_RTCSEL) + +/** @brief Macros to force or release the Backup domain reset. + * @note This function resets the RTC peripheral (including the backup registers) + * and the RTC clock source selection in RCC_CSR register. + * @note The BKPSRAM is not affected by this reset. + */ +#define __HAL_RCC_BACKUPRESET_FORCE() (*(__IO uint32_t *) RCC_BDCR_BDRST_BB = ENABLE) +#define __HAL_RCC_BACKUPRESET_RELEASE() (*(__IO uint32_t *) RCC_BDCR_BDRST_BB = DISABLE) +/** + * @} + */ + +/** @defgroup RCC_PLL_Configuration PLL Configuration + * @{ + */ + +/** @brief Macros to enable or disable the main PLL. + * @note After enabling the main PLL, the application software should wait on + * PLLRDY flag to be set indicating that PLL clock is stable and can + * be used as system clock source. + * @note The main PLL can not be disabled if it is used as system clock source + * @note The main PLL is disabled by hardware when entering STOP and STANDBY modes. + */ +#define __HAL_RCC_PLL_ENABLE() (*(__IO uint32_t *) RCC_CR_PLLON_BB = ENABLE) +#define __HAL_RCC_PLL_DISABLE() (*(__IO uint32_t *) RCC_CR_PLLON_BB = DISABLE) + +/** @brief Macro to configure the PLL clock source. + * @note This function must be used only when the main PLL is disabled. + * @param __PLLSOURCE__ specifies the PLL entry clock source. + * This parameter can be one of the following values: + * @arg RCC_PLLSOURCE_HSI: HSI oscillator clock selected as PLL clock entry + * @arg RCC_PLLSOURCE_HSE: HSE oscillator clock selected as PLL clock entry + * + */ +#define __HAL_RCC_PLL_PLLSOURCE_CONFIG(__PLLSOURCE__) MODIFY_REG(RCC->PLLCFGR, RCC_PLLCFGR_PLLSRC, (__PLLSOURCE__)) + +/** @brief Macro to configure the PLL multiplication factor. + * @note This function must be used only when the main PLL is disabled. + * @param __PLLM__ specifies the division factor for PLL VCO input clock + * This parameter must be a number between Min_Data = 2 and Max_Data = 63. + * @note You have to set the PLLM parameter correctly to ensure that the VCO input + * frequency ranges from 1 to 2 MHz. It is recommended to select a frequency + * of 2 MHz to limit PLL jitter. + * + */ +#define __HAL_RCC_PLL_PLLM_CONFIG(__PLLM__) MODIFY_REG(RCC->PLLCFGR, RCC_PLLCFGR_PLLM, (__PLLM__)) +/** + * @} + */ + +/** @defgroup RCC_Get_Clock_source Get Clock source + * @{ + */ +/** + * @brief Macro to configure the system clock source. + * @param __RCC_SYSCLKSOURCE__ specifies the system clock source. + * This parameter can be one of the following values: + * - RCC_SYSCLKSOURCE_HSI: HSI oscillator is used as system clock source. + * - RCC_SYSCLKSOURCE_HSE: HSE oscillator is used as system clock source. + * - RCC_SYSCLKSOURCE_PLLCLK: PLL output is used as system clock source. + * - RCC_SYSCLKSOURCE_PLLRCLK: PLLR output is used as system clock source. This + * parameter is available only for STM32F446xx devices. + */ +#define __HAL_RCC_SYSCLK_CONFIG(__RCC_SYSCLKSOURCE__) MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, (__RCC_SYSCLKSOURCE__)) + +/** @brief Macro to get the clock source used as system clock. + * @retval The clock source used as system clock. The returned value can be one + * of the following: + * - RCC_SYSCLKSOURCE_STATUS_HSI: HSI used as system clock. + * - RCC_SYSCLKSOURCE_STATUS_HSE: HSE used as system clock. + * - RCC_SYSCLKSOURCE_STATUS_PLLCLK: PLL used as system clock. + * - RCC_SYSCLKSOURCE_STATUS_PLLRCLK: PLLR used as system clock. This parameter + * is available only for STM32F446xx devices. + */ +#define __HAL_RCC_GET_SYSCLK_SOURCE() (RCC->CFGR & RCC_CFGR_SWS) + +/** @brief Macro to get the oscillator used as PLL clock source. + * @retval The oscillator used as PLL clock source. The returned value can be one + * of the following: + * - RCC_PLLSOURCE_HSI: HSI oscillator is used as PLL clock source. + * - RCC_PLLSOURCE_HSE: HSE oscillator is used as PLL clock source. + */ +#define __HAL_RCC_GET_PLL_OSCSOURCE() ((uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC)) +/** + * @} + */ + +/** @defgroup RCCEx_MCOx_Clock_Config RCC Extended MCOx Clock Config + * @{ + */ + +/** @brief Macro to configure the MCO1 clock. + * @param __MCOCLKSOURCE__ specifies the MCO clock source. + * This parameter can be one of the following values: + * @arg RCC_MCO1SOURCE_HSI: HSI clock selected as MCO1 source + * @arg RCC_MCO1SOURCE_LSE: LSE clock selected as MCO1 source + * @arg RCC_MCO1SOURCE_HSE: HSE clock selected as MCO1 source + * @arg RCC_MCO1SOURCE_PLLCLK: main PLL clock selected as MCO1 source + * @param __MCODIV__ specifies the MCO clock prescaler. + * This parameter can be one of the following values: + * @arg RCC_MCODIV_1: no division applied to MCOx clock + * @arg RCC_MCODIV_2: division by 2 applied to MCOx clock + * @arg RCC_MCODIV_3: division by 3 applied to MCOx clock + * @arg RCC_MCODIV_4: division by 4 applied to MCOx clock + * @arg RCC_MCODIV_5: division by 5 applied to MCOx clock + */ +#define __HAL_RCC_MCO1_CONFIG(__MCOCLKSOURCE__, __MCODIV__) \ + MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO1 | RCC_CFGR_MCO1PRE), ((__MCOCLKSOURCE__) | (__MCODIV__))) + +/** @brief Macro to configure the MCO2 clock. + * @param __MCOCLKSOURCE__ specifies the MCO clock source. + * This parameter can be one of the following values: + * @arg RCC_MCO2SOURCE_SYSCLK: System clock (SYSCLK) selected as MCO2 source + * @arg RCC_MCO2SOURCE_PLLI2SCLK: PLLI2S clock selected as MCO2 source, available for all STM32F4 devices except STM32F410xx + * @arg RCC_MCO2SOURCE_I2SCLK: I2SCLK clock selected as MCO2 source, available only for STM32F410Rx devices + * @arg RCC_MCO2SOURCE_HSE: HSE clock selected as MCO2 source + * @arg RCC_MCO2SOURCE_PLLCLK: main PLL clock selected as MCO2 source + * @param __MCODIV__ specifies the MCO clock prescaler. + * This parameter can be one of the following values: + * @arg RCC_MCODIV_1: no division applied to MCOx clock + * @arg RCC_MCODIV_2: division by 2 applied to MCOx clock + * @arg RCC_MCODIV_3: division by 3 applied to MCOx clock + * @arg RCC_MCODIV_4: division by 4 applied to MCOx clock + * @arg RCC_MCODIV_5: division by 5 applied to MCOx clock + * @note For STM32F410Rx devices, to output I2SCLK clock on MCO2, you should have + * at least one of the SPI clocks enabled (SPI1, SPI2 or SPI5). + */ +#define __HAL_RCC_MCO2_CONFIG(__MCOCLKSOURCE__, __MCODIV__) \ + MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO2 | RCC_CFGR_MCO2PRE), ((__MCOCLKSOURCE__) | ((__MCODIV__) << 3U))); +/** + * @} + */ + +/** @defgroup RCC_Flags_Interrupts_Management Flags Interrupts Management + * @brief macros to manage the specified RCC Flags and interrupts. + * @{ + */ + +/** @brief Enable RCC interrupt (Perform Byte access to RCC_CIR[14:8] bits to enable + * the selected interrupts). + * @param __INTERRUPT__ specifies the RCC interrupt sources to be enabled. + * This parameter can be any combination of the following values: + * @arg RCC_IT_LSIRDY: LSI ready interrupt. + * @arg RCC_IT_LSERDY: LSE ready interrupt. + * @arg RCC_IT_HSIRDY: HSI ready interrupt. + * @arg RCC_IT_HSERDY: HSE ready interrupt. + * @arg RCC_IT_PLLRDY: Main PLL ready interrupt. + * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt. + */ +#define __HAL_RCC_ENABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS |= (__INTERRUPT__)) + +/** @brief Disable RCC interrupt (Perform Byte access to RCC_CIR[14:8] bits to disable + * the selected interrupts). + * @param __INTERRUPT__ specifies the RCC interrupt sources to be disabled. + * This parameter can be any combination of the following values: + * @arg RCC_IT_LSIRDY: LSI ready interrupt. + * @arg RCC_IT_LSERDY: LSE ready interrupt. + * @arg RCC_IT_HSIRDY: HSI ready interrupt. + * @arg RCC_IT_HSERDY: HSE ready interrupt. + * @arg RCC_IT_PLLRDY: Main PLL ready interrupt. + * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt. + */ +#define __HAL_RCC_DISABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS &= (uint8_t)(~(__INTERRUPT__))) + +/** @brief Clear the RCC's interrupt pending bits (Perform Byte access to RCC_CIR[23:16] + * bits to clear the selected interrupt pending bits. + * @param __INTERRUPT__ specifies the interrupt pending bit to clear. + * This parameter can be any combination of the following values: + * @arg RCC_IT_LSIRDY: LSI ready interrupt. + * @arg RCC_IT_LSERDY: LSE ready interrupt. + * @arg RCC_IT_HSIRDY: HSI ready interrupt. + * @arg RCC_IT_HSERDY: HSE ready interrupt. + * @arg RCC_IT_PLLRDY: Main PLL ready interrupt. + * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt. + * @arg RCC_IT_CSS: Clock Security System interrupt + */ +#define __HAL_RCC_CLEAR_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE2_ADDRESS = (__INTERRUPT__)) + +/** @brief Check the RCC's interrupt has occurred or not. + * @param __INTERRUPT__ specifies the RCC interrupt source to check. + * This parameter can be one of the following values: + * @arg RCC_IT_LSIRDY: LSI ready interrupt. + * @arg RCC_IT_LSERDY: LSE ready interrupt. + * @arg RCC_IT_HSIRDY: HSI ready interrupt. + * @arg RCC_IT_HSERDY: HSE ready interrupt. + * @arg RCC_IT_PLLRDY: Main PLL ready interrupt. + * @arg RCC_IT_PLLI2SRDY: PLLI2S ready interrupt. + * @arg RCC_IT_CSS: Clock Security System interrupt + * @retval The new state of __INTERRUPT__ (TRUE or FALSE). + */ +#define __HAL_RCC_GET_IT(__INTERRUPT__) ((RCC->CIR & (__INTERRUPT__)) == (__INTERRUPT__)) + +/** @brief Set RMVF bit to clear the reset flags: RCC_FLAG_PINRST, RCC_FLAG_PORRST, + * RCC_FLAG_SFTRST, RCC_FLAG_IWDGRST, RCC_FLAG_WWDGRST and RCC_FLAG_LPWRRST. + */ +#define __HAL_RCC_CLEAR_RESET_FLAGS() (RCC->CSR |= RCC_CSR_RMVF) + +/** @brief Check RCC flag is set or not. + * @param __FLAG__ specifies the flag to check. + * This parameter can be one of the following values: + * @arg RCC_FLAG_HSIRDY: HSI oscillator clock ready. + * @arg RCC_FLAG_HSERDY: HSE oscillator clock ready. + * @arg RCC_FLAG_PLLRDY: Main PLL clock ready. + * @arg RCC_FLAG_PLLI2SRDY: PLLI2S clock ready. + * @arg RCC_FLAG_LSERDY: LSE oscillator clock ready. + * @arg RCC_FLAG_LSIRDY: LSI oscillator clock ready. + * @arg RCC_FLAG_BORRST: POR/PDR or BOR reset. + * @arg RCC_FLAG_PINRST: Pin reset. + * @arg RCC_FLAG_PORRST: POR/PDR reset. + * @arg RCC_FLAG_SFTRST: Software reset. + * @arg RCC_FLAG_IWDGRST: Independent Watchdog reset. + * @arg RCC_FLAG_WWDGRST: Window Watchdog reset. + * @arg RCC_FLAG_LPWRRST: Low Power reset. + * @retval The new state of __FLAG__ (TRUE or FALSE). + */ +#define RCC_FLAG_MASK ((uint8_t)0x1FU) +#define __HAL_RCC_GET_FLAG(__FLAG__) (((((((__FLAG__) >> 5U) == 1U)? RCC->CR :((((__FLAG__) >> 5U) == 2U) ? RCC->BDCR :((((__FLAG__) >> 5U) == 3U)? RCC->CSR :RCC->CIR))) & (1U << ((__FLAG__) & RCC_FLAG_MASK)))!= 0U)? 1U : 0U) + +/** + * @} + */ + +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ + /** @addtogroup RCC_Exported_Functions + * @{ + */ + +/** @addtogroup RCC_Exported_Functions_Group1 + * @{ + */ +/* Initialization and de-initialization functions ******************************/ +HAL_StatusTypeDef HAL_RCC_DeInit(void); +HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct); +HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency); +/** + * @} + */ + +/** @addtogroup RCC_Exported_Functions_Group2 + * @{ + */ +/* Peripheral Control functions ************************************************/ +void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv); +void HAL_RCC_EnableCSS(void); +void HAL_RCC_DisableCSS(void); +uint32_t HAL_RCC_GetSysClockFreq(void); +uint32_t HAL_RCC_GetHCLKFreq(void); +uint32_t HAL_RCC_GetPCLK1Freq(void); +uint32_t HAL_RCC_GetPCLK2Freq(void); +void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct); +void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency); + +/* CSS NMI IRQ handler */ +void HAL_RCC_NMI_IRQHandler(void); + +/* User Callbacks in non blocking mode (IT mode) */ +void HAL_RCC_CSSCallback(void); + +/** + * @} + */ + +/** + * @} + */ + +/* Private types -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private constants ---------------------------------------------------------*/ +/** @defgroup RCC_Private_Constants RCC Private Constants + * @{ + */ + +/** @defgroup RCC_BitAddress_AliasRegion RCC BitAddress AliasRegion + * @brief RCC registers bit address in the alias region + * @{ + */ +#define RCC_OFFSET (RCC_BASE - PERIPH_BASE) +/* --- CR Register --- */ +/* Alias word address of HSION bit */ +#define RCC_CR_OFFSET (RCC_OFFSET + 0x00U) +#define RCC_HSION_BIT_NUMBER 0x00U +#define RCC_CR_HSION_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32U) + (RCC_HSION_BIT_NUMBER * 4U)) +/* Alias word address of CSSON bit */ +#define RCC_CSSON_BIT_NUMBER 0x13U +#define RCC_CR_CSSON_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32U) + (RCC_CSSON_BIT_NUMBER * 4U)) +/* Alias word address of PLLON bit */ +#define RCC_PLLON_BIT_NUMBER 0x18U +#define RCC_CR_PLLON_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32U) + (RCC_PLLON_BIT_NUMBER * 4U)) + +/* --- BDCR Register --- */ +/* Alias word address of RTCEN bit */ +#define RCC_BDCR_OFFSET (RCC_OFFSET + 0x70U) +#define RCC_RTCEN_BIT_NUMBER 0x0FU +#define RCC_BDCR_RTCEN_BB (PERIPH_BB_BASE + (RCC_BDCR_OFFSET * 32U) + (RCC_RTCEN_BIT_NUMBER * 4U)) +/* Alias word address of BDRST bit */ +#define RCC_BDRST_BIT_NUMBER 0x10U +#define RCC_BDCR_BDRST_BB (PERIPH_BB_BASE + (RCC_BDCR_OFFSET * 32U) + (RCC_BDRST_BIT_NUMBER * 4U)) + +/* --- CSR Register --- */ +/* Alias word address of LSION bit */ +#define RCC_CSR_OFFSET (RCC_OFFSET + 0x74U) +#define RCC_LSION_BIT_NUMBER 0x00U +#define RCC_CSR_LSION_BB (PERIPH_BB_BASE + (RCC_CSR_OFFSET * 32U) + (RCC_LSION_BIT_NUMBER * 4U)) + +/* CR register byte 3 (Bits[23:16]) base address */ +#define RCC_CR_BYTE2_ADDRESS 0x40023802U + +/* CIR register byte 2 (Bits[15:8]) base address */ +#define RCC_CIR_BYTE1_ADDRESS ((uint32_t)(RCC_BASE + 0x0CU + 0x01U)) + +/* CIR register byte 3 (Bits[23:16]) base address */ +#define RCC_CIR_BYTE2_ADDRESS ((uint32_t)(RCC_BASE + 0x0CU + 0x02U)) + +/* BDCR register base address */ +#define RCC_BDCR_BYTE0_ADDRESS (PERIPH_BASE + RCC_BDCR_OFFSET) + +#define RCC_DBP_TIMEOUT_VALUE 2U +#define RCC_LSE_TIMEOUT_VALUE LSE_STARTUP_TIMEOUT + +#define HSE_TIMEOUT_VALUE HSE_STARTUP_TIMEOUT +#define HSI_TIMEOUT_VALUE 2U /* 2 ms */ +#define LSI_TIMEOUT_VALUE 2U /* 2 ms */ +#define CLOCKSWITCH_TIMEOUT_VALUE 5000U /* 5 s */ + +/** + * @} + */ + +/** + * @} + */ + +/* Private macros ------------------------------------------------------------*/ +/** @defgroup RCC_Private_Macros RCC Private Macros + * @{ + */ + +/** @defgroup RCC_IS_RCC_Definitions RCC Private macros to check input parameters + * @{ + */ +#define IS_RCC_OSCILLATORTYPE(OSCILLATOR) ((OSCILLATOR) <= 15U) + +#define IS_RCC_HSE(HSE) (((HSE) == RCC_HSE_OFF) || ((HSE) == RCC_HSE_ON) || \ + ((HSE) == RCC_HSE_BYPASS)) + +#define IS_RCC_LSE(LSE) (((LSE) == RCC_LSE_OFF) || ((LSE) == RCC_LSE_ON) || \ + ((LSE) == RCC_LSE_BYPASS)) + +#define IS_RCC_HSI(HSI) (((HSI) == RCC_HSI_OFF) || ((HSI) == RCC_HSI_ON)) + +#define IS_RCC_LSI(LSI) (((LSI) == RCC_LSI_OFF) || ((LSI) == RCC_LSI_ON)) + +#define IS_RCC_PLL(PLL) (((PLL) == RCC_PLL_NONE) ||((PLL) == RCC_PLL_OFF) || ((PLL) == RCC_PLL_ON)) + +#define IS_RCC_PLLSOURCE(SOURCE) (((SOURCE) == RCC_PLLSOURCE_HSI) || \ + ((SOURCE) == RCC_PLLSOURCE_HSE)) + +#define IS_RCC_SYSCLKSOURCE(SOURCE) (((SOURCE) == RCC_SYSCLKSOURCE_HSI) || \ + ((SOURCE) == RCC_SYSCLKSOURCE_HSE) || \ + ((SOURCE) == RCC_SYSCLKSOURCE_PLLCLK) || \ + ((SOURCE) == RCC_SYSCLKSOURCE_PLLRCLK)) + +#define IS_RCC_RTCCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_RTCCLKSOURCE_LSE) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_LSI) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV2) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV3) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV4) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV5) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV6) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV7) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV8) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV9) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV10) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV11) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV12) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV13) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV14) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV15) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV16) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV17) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV18) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV19) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV20) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV21) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV22) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV23) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV24) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV25) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV26) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV27) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV28) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV29) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV30) || \ + ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV31)) + +#define IS_RCC_PLLM_VALUE(VALUE) ((VALUE) <= 63U) + +#define IS_RCC_PLLP_VALUE(VALUE) (((VALUE) == 2U) || ((VALUE) == 4U) || ((VALUE) == 6U) || ((VALUE) == 8U)) + +#define IS_RCC_PLLQ_VALUE(VALUE) ((2U <= (VALUE)) && ((VALUE) <= 15U)) + +#define IS_RCC_HCLK(HCLK) (((HCLK) == RCC_SYSCLK_DIV1) || ((HCLK) == RCC_SYSCLK_DIV2) || \ + ((HCLK) == RCC_SYSCLK_DIV4) || ((HCLK) == RCC_SYSCLK_DIV8) || \ + ((HCLK) == RCC_SYSCLK_DIV16) || ((HCLK) == RCC_SYSCLK_DIV64) || \ + ((HCLK) == RCC_SYSCLK_DIV128) || ((HCLK) == RCC_SYSCLK_DIV256) || \ + ((HCLK) == RCC_SYSCLK_DIV512)) + +#define IS_RCC_CLOCKTYPE(CLK) ((1U <= (CLK)) && ((CLK) <= 15U)) + +#define IS_RCC_PCLK(PCLK) (((PCLK) == RCC_HCLK_DIV1) || ((PCLK) == RCC_HCLK_DIV2) || \ + ((PCLK) == RCC_HCLK_DIV4) || ((PCLK) == RCC_HCLK_DIV8) || \ + ((PCLK) == RCC_HCLK_DIV16)) + +#define IS_RCC_MCO(MCOx) (((MCOx) == RCC_MCO1) || ((MCOx) == RCC_MCO2)) + +#define IS_RCC_MCO1SOURCE(SOURCE) (((SOURCE) == RCC_MCO1SOURCE_HSI) || ((SOURCE) == RCC_MCO1SOURCE_LSE) || \ + ((SOURCE) == RCC_MCO1SOURCE_HSE) || ((SOURCE) == RCC_MCO1SOURCE_PLLCLK)) + +#define IS_RCC_MCODIV(DIV) (((DIV) == RCC_MCODIV_1) || ((DIV) == RCC_MCODIV_2) || \ + ((DIV) == RCC_MCODIV_3) || ((DIV) == RCC_MCODIV_4) || \ + ((DIV) == RCC_MCODIV_5)) +#define IS_RCC_CALIBRATION_VALUE(VALUE) ((VALUE) <= 0x1FU) + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F4xx_HAL_RCC_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/