Mercurial > public > ostc4
diff Common/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c @ 128:c78bcbd5deda FlipDisplay
Added current STM32 standandard libraries in version independend folder structure
author | Ideenmodellierer |
---|---|
date | Sun, 17 Feb 2019 21:12:22 +0100 |
parents | |
children | 4e10a3e087a1 |
line wrap: on
line diff
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/Common/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c Sun Feb 17 21:12:22 2019 +0100 @@ -0,0 +1,1113 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_rcc.c + * @author MCD Application Team + * @brief RCC HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Reset and Clock Control (RCC) peripheral: + * + Initialization and de-initialization functions + * + Peripheral Control functions + * + @verbatim + ============================================================================== + ##### RCC specific features ##### + ============================================================================== + [..] + After reset the device is running from Internal High Speed oscillator + (HSI 16MHz) with Flash 0 wait state, Flash prefetch buffer, D-Cache + and I-Cache are disabled, and all peripherals are off except internal + SRAM, Flash and JTAG. + (+) There is no prescaler on High speed (AHB) and Low speed (APB) busses; + all peripherals mapped on these busses are running at HSI speed. + (+) The clock for all peripherals is switched off, except the SRAM and FLASH. + (+) All GPIOs are in input floating state, except the JTAG pins which + are assigned to be used for debug purpose. + + [..] + Once the device started from reset, the user application has to: + (+) Configure the clock source to be used to drive the System clock + (if the application needs higher frequency/performance) + (+) Configure the System clock frequency and Flash settings + (+) Configure the AHB and APB busses prescalers + (+) Enable the clock for the peripheral(s) to be used + (+) Configure the clock source(s) for peripherals which clocks are not + derived from the System clock (I2S, RTC, ADC, USB OTG FS/SDIO/RNG) + + ##### RCC Limitations ##### + ============================================================================== + [..] + A delay between an RCC peripheral clock enable and the effective peripheral + enabling should be taken into account in order to manage the peripheral read/write + from/to registers. + (+) This delay depends on the peripheral mapping. + (+) If peripheral is mapped on AHB: the delay is 2 AHB clock cycle + after the clock enable bit is set on the hardware register + (+) If peripheral is mapped on APB: the delay is 2 APB clock cycle + after the clock enable bit is set on the hardware register + + [..] + Implemented Workaround: + (+) For AHB & APB peripherals, a dummy read to the peripheral register has been + inserted in each __HAL_RCC_PPP_CLK_ENABLE() macro. + + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f4xx_hal.h" + +/** @addtogroup STM32F4xx_HAL_Driver + * @{ + */ + +/** @defgroup RCC RCC + * @brief RCC HAL module driver + * @{ + */ + +#ifdef HAL_RCC_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @addtogroup RCC_Private_Constants + * @{ + */ + +/* Private macro -------------------------------------------------------------*/ +#define __MCO1_CLK_ENABLE() __HAL_RCC_GPIOA_CLK_ENABLE() +#define MCO1_GPIO_PORT GPIOA +#define MCO1_PIN GPIO_PIN_8 + +#define __MCO2_CLK_ENABLE() __HAL_RCC_GPIOC_CLK_ENABLE() +#define MCO2_GPIO_PORT GPIOC +#define MCO2_PIN GPIO_PIN_9 +/** + * @} + */ + +/* Private variables ---------------------------------------------------------*/ +/** @defgroup RCC_Private_Variables RCC Private Variables + * @{ + */ +/** + * @} + */ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup RCC_Exported_Functions RCC Exported Functions + * @{ + */ + +/** @defgroup RCC_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and de-initialization functions ##### + =============================================================================== + [..] + This section provides functions allowing to configure the internal/external oscillators + (HSE, HSI, LSE, LSI, PLL, CSS and MCO) and the System busses clocks (SYSCLK, AHB, APB1 + and APB2). + + [..] Internal/external clock and PLL configuration + (#) HSI (high-speed internal), 16 MHz factory-trimmed RC used directly or through + the PLL as System clock source. + + (#) LSI (low-speed internal), 32 KHz low consumption RC used as IWDG and/or RTC + clock source. + + (#) HSE (high-speed external), 4 to 26 MHz crystal oscillator used directly or + through the PLL as System clock source. Can be used also as RTC clock source. + + (#) LSE (low-speed external), 32 KHz oscillator used as RTC clock source. + + (#) PLL (clocked by HSI or HSE), featuring two different output clocks: + (++) The first output is used to generate the high speed system clock (up to 168 MHz) + (++) The second output is used to generate the clock for the USB OTG FS (48 MHz), + the random analog generator (<=48 MHz) and the SDIO (<= 48 MHz). + + (#) CSS (Clock security system), once enable using the macro __HAL_RCC_CSS_ENABLE() + and if a HSE clock failure occurs(HSE used directly or through PLL as System + clock source), the System clocks automatically switched to HSI and an interrupt + is generated if enabled. The interrupt is linked to the Cortex-M4 NMI + (Non-Maskable Interrupt) exception vector. + + (#) MCO1 (microcontroller clock output), used to output HSI, LSE, HSE or PLL + clock (through a configurable prescaler) on PA8 pin. + + (#) MCO2 (microcontroller clock output), used to output HSE, PLL, SYSCLK or PLLI2S + clock (through a configurable prescaler) on PC9 pin. + + [..] System, AHB and APB busses clocks configuration + (#) Several clock sources can be used to drive the System clock (SYSCLK): HSI, + HSE and PLL. + The AHB clock (HCLK) is derived from System clock through configurable + prescaler and used to clock the CPU, memory and peripherals mapped + on AHB bus (DMA, GPIO...). APB1 (PCLK1) and APB2 (PCLK2) clocks are derived + from AHB clock through configurable prescalers and used to clock + the peripherals mapped on these busses. You can use + "HAL_RCC_GetSysClockFreq()" function to retrieve the frequencies of these clocks. + + (#) For the STM32F405xx/07xx and STM32F415xx/17xx devices, the maximum + frequency of the SYSCLK and HCLK is 168 MHz, PCLK2 84 MHz and PCLK1 42 MHz. + Depending on the device voltage range, the maximum frequency should + be adapted accordingly (refer to the product datasheets for more details). + + (#) For the STM32F42xxx, STM32F43xxx, STM32F446xx, STM32F469xx and STM32F479xx devices, + the maximum frequency of the SYSCLK and HCLK is 180 MHz, PCLK2 90 MHz and PCLK1 45 MHz. + Depending on the device voltage range, the maximum frequency should + be adapted accordingly (refer to the product datasheets for more details). + + (#) For the STM32F401xx, the maximum frequency of the SYSCLK and HCLK is 84 MHz, + PCLK2 84 MHz and PCLK1 42 MHz. + Depending on the device voltage range, the maximum frequency should + be adapted accordingly (refer to the product datasheets for more details). + + (#) For the STM32F41xxx, the maximum frequency of the SYSCLK and HCLK is 100 MHz, + PCLK2 100 MHz and PCLK1 50 MHz. + Depending on the device voltage range, the maximum frequency should + be adapted accordingly (refer to the product datasheets for more details). + +@endverbatim + * @{ + */ + +/** + * @brief Resets the RCC clock configuration to the default reset state. + * @note The default reset state of the clock configuration is given below: + * - HSI ON and used as system clock source + * - HSE and PLL OFF + * - AHB, APB1 and APB2 prescaler set to 1. + * - CSS, MCO1 and MCO2 OFF + * - All interrupts disabled + * @note This function doesn't modify the configuration of the + * - Peripheral clocks + * - LSI, LSE and RTC clocks + * @retval HAL status + */ +__weak HAL_StatusTypeDef HAL_RCC_DeInit(void) +{ + return HAL_OK; +} + +/** + * @brief Initializes the RCC Oscillators according to the specified parameters in the + * RCC_OscInitTypeDef. + * @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that + * contains the configuration information for the RCC Oscillators. + * @note The PLL is not disabled when used as system clock. + * @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not + * supported by this API. User should request a transition to LSE Off + * first and then LSE On or LSE Bypass. + * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not + * supported by this API. User should request a transition to HSE Off + * first and then HSE On or HSE Bypass. + * @retval HAL status + */ +__weak HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct) +{ + uint32_t tickstart; + + /* Check Null pointer */ + if(RCC_OscInitStruct == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType)); + /*------------------------------- HSE Configuration ------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) + { + /* Check the parameters */ + assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState)); + /* When the HSE is used as system clock or clock source for PLL in these cases HSE will not disabled */ + if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSE) ||\ + ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSE))) + { + if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) && (RCC_OscInitStruct->HSEState == RCC_HSE_OFF)) + { + return HAL_ERROR; + } + } + else + { + /* Set the new HSE configuration ---------------------------------------*/ + __HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState); + + /* Check the HSE State */ + if((RCC_OscInitStruct->HSEState) != RCC_HSE_OFF) + { + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till HSE is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till HSE is bypassed or disabled */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + } + /*----------------------------- HSI Configuration --------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) + { + /* Check the parameters */ + assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState)); + assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue)); + + /* Check if HSI is used as system clock or as PLL source when PLL is selected as system clock */ + if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSI) ||\ + ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSI))) + { + /* When HSI is used as system clock it will not disabled */ + if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON)) + { + return HAL_ERROR; + } + /* Otherwise, just the calibration is allowed */ + else + { + /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ + __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); + } + } + else + { + /* Check the HSI State */ + if((RCC_OscInitStruct->HSIState)!= RCC_HSI_OFF) + { + /* Enable the Internal High Speed oscillator (HSI). */ + __HAL_RCC_HSI_ENABLE(); + + /* Get Start Tick*/ + tickstart = HAL_GetTick(); + + /* Wait till HSI is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Adjusts the Internal High Speed oscillator (HSI) calibration value. */ + __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); + } + else + { + /* Disable the Internal High Speed oscillator (HSI). */ + __HAL_RCC_HSI_DISABLE(); + + /* Get Start Tick*/ + tickstart = HAL_GetTick(); + + /* Wait till HSI is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + } + /*------------------------------ LSI Configuration -------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) + { + /* Check the parameters */ + assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState)); + + /* Check the LSI State */ + if((RCC_OscInitStruct->LSIState)!= RCC_LSI_OFF) + { + /* Enable the Internal Low Speed oscillator (LSI). */ + __HAL_RCC_LSI_ENABLE(); + + /* Get Start Tick*/ + tickstart = HAL_GetTick(); + + /* Wait till LSI is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Disable the Internal Low Speed oscillator (LSI). */ + __HAL_RCC_LSI_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till LSI is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + /*------------------------------ LSE Configuration -------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE) + { + FlagStatus pwrclkchanged = RESET; + + /* Check the parameters */ + assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState)); + + /* Update LSE configuration in Backup Domain control register */ + /* Requires to enable write access to Backup Domain of necessary */ + if(__HAL_RCC_PWR_IS_CLK_DISABLED()) + { + __HAL_RCC_PWR_CLK_ENABLE(); + pwrclkchanged = SET; + } + + if(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP)) + { + /* Enable write access to Backup domain */ + SET_BIT(PWR->CR, PWR_CR_DBP); + + /* Wait for Backup domain Write protection disable */ + tickstart = HAL_GetTick(); + + while(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP)) + { + if((HAL_GetTick() - tickstart) > RCC_DBP_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + + /* Set the new LSE configuration -----------------------------------------*/ + __HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState); + /* Check the LSE State */ + if((RCC_OscInitStruct->LSEState) != RCC_LSE_OFF) + { + /* Get Start Tick*/ + tickstart = HAL_GetTick(); + + /* Wait till LSE is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till LSE is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + + /* Restore clock configuration if changed */ + if(pwrclkchanged == SET) + { + __HAL_RCC_PWR_CLK_DISABLE(); + } + } + /*-------------------------------- PLL Configuration -----------------------*/ + /* Check the parameters */ + assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState)); + if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE) + { + /* Check if the PLL is used as system clock or not */ + if(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_PLL) + { + if((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON) + { + /* Check the parameters */ + assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource)); + assert_param(IS_RCC_PLLM_VALUE(RCC_OscInitStruct->PLL.PLLM)); + assert_param(IS_RCC_PLLN_VALUE(RCC_OscInitStruct->PLL.PLLN)); + assert_param(IS_RCC_PLLP_VALUE(RCC_OscInitStruct->PLL.PLLP)); + assert_param(IS_RCC_PLLQ_VALUE(RCC_OscInitStruct->PLL.PLLQ)); + + /* Disable the main PLL. */ + __HAL_RCC_PLL_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Configure the main PLL clock source, multiplication and division factors. */ + WRITE_REG(RCC->PLLCFGR, (RCC_OscInitStruct->PLL.PLLSource | \ + RCC_OscInitStruct->PLL.PLLM | \ + (RCC_OscInitStruct->PLL.PLLN << RCC_PLLCFGR_PLLN_Pos) | \ + (((RCC_OscInitStruct->PLL.PLLP >> 1U) - 1U) << RCC_PLLCFGR_PLLP_Pos) | \ + (RCC_OscInitStruct->PLL.PLLQ << RCC_PLLCFGR_PLLQ_Pos))); + /* Enable the main PLL. */ + __HAL_RCC_PLL_ENABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Disable the main PLL. */ + __HAL_RCC_PLL_DISABLE(); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + /* Wait till PLL is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + else + { + return HAL_ERROR; + } + } + return HAL_OK; +} + +/** + * @brief Initializes the CPU, AHB and APB busses clocks according to the specified + * parameters in the RCC_ClkInitStruct. + * @param RCC_ClkInitStruct pointer to an RCC_OscInitTypeDef structure that + * contains the configuration information for the RCC peripheral. + * @param FLatency FLASH Latency, this parameter depend on device selected + * + * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency + * and updated by HAL_RCC_GetHCLKFreq() function called within this function + * + * @note The HSI is used (enabled by hardware) as system clock source after + * startup from Reset, wake-up from STOP and STANDBY mode, or in case + * of failure of the HSE used directly or indirectly as system clock + * (if the Clock Security System CSS is enabled). + * + * @note A switch from one clock source to another occurs only if the target + * clock source is ready (clock stable after startup delay or PLL locked). + * If a clock source which is not yet ready is selected, the switch will + * occur when the clock source will be ready. + * + * @note Depending on the device voltage range, the software has to set correctly + * HPRE[3:0] bits to ensure that HCLK not exceed the maximum allowed frequency + * (for more details refer to section above "Initialization/de-initialization functions") + * @retval None + */ +HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency) +{ + uint32_t tickstart; + + /* Check Null pointer */ + if(RCC_ClkInitStruct == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_RCC_CLOCKTYPE(RCC_ClkInitStruct->ClockType)); + assert_param(IS_FLASH_LATENCY(FLatency)); + + /* To correctly read data from FLASH memory, the number of wait states (LATENCY) + must be correctly programmed according to the frequency of the CPU clock + (HCLK) and the supply voltage of the device. */ + + /* Increasing the number of wait states because of higher CPU frequency */ + if(FLatency > __HAL_FLASH_GET_LATENCY()) + { + /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */ + __HAL_FLASH_SET_LATENCY(FLatency); + + /* Check that the new number of wait states is taken into account to access the Flash + memory by reading the FLASH_ACR register */ + if(__HAL_FLASH_GET_LATENCY() != FLatency) + { + return HAL_ERROR; + } + } + + /*-------------------------- HCLK Configuration --------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK) + { + /* Set the highest APBx dividers in order to ensure that we do not go through + a non-spec phase whatever we decrease or increase HCLK. */ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1) + { + MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_HCLK_DIV16); + } + + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2) + { + MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, (RCC_HCLK_DIV16 << 3)); + } + + assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider)); + MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider); + } + + /*------------------------- SYSCLK Configuration ---------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK) + { + assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource)); + + /* HSE is selected as System Clock Source */ + if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE) + { + /* Check the HSE ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) + { + return HAL_ERROR; + } + } + /* PLL is selected as System Clock Source */ + else if((RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK) || + (RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLRCLK)) + { + /* Check the PLL ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) + { + return HAL_ERROR; + } + } + /* HSI is selected as System Clock Source */ + else + { + /* Check the HSI ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) + { + return HAL_ERROR; + } + } + + __HAL_RCC_SYSCLK_CONFIG(RCC_ClkInitStruct->SYSCLKSource); + + /* Get Start Tick */ + tickstart = HAL_GetTick(); + + while (__HAL_RCC_GET_SYSCLK_SOURCE() != (RCC_ClkInitStruct->SYSCLKSource << RCC_CFGR_SWS_Pos)) + { + if ((HAL_GetTick() - tickstart) > CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + + /* Decreasing the number of wait states because of lower CPU frequency */ + if(FLatency < __HAL_FLASH_GET_LATENCY()) + { + /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */ + __HAL_FLASH_SET_LATENCY(FLatency); + + /* Check that the new number of wait states is taken into account to access the Flash + memory by reading the FLASH_ACR register */ + if(__HAL_FLASH_GET_LATENCY() != FLatency) + { + return HAL_ERROR; + } + } + + /*-------------------------- PCLK1 Configuration ---------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1) + { + assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB1CLKDivider)); + MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_ClkInitStruct->APB1CLKDivider); + } + + /*-------------------------- PCLK2 Configuration ---------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2) + { + assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB2CLKDivider)); + MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, ((RCC_ClkInitStruct->APB2CLKDivider) << 3U)); + } + + /* Update the SystemCoreClock global variable */ + SystemCoreClock = HAL_RCC_GetSysClockFreq() >> AHBPrescTable[(RCC->CFGR & RCC_CFGR_HPRE)>> RCC_CFGR_HPRE_Pos]; + + /* Configure the source of time base considering new system clocks settings */ + HAL_InitTick (TICK_INT_PRIORITY); + + return HAL_OK; +} + +/** + * @} + */ + +/** @defgroup RCC_Exported_Functions_Group2 Peripheral Control functions + * @brief RCC clocks control functions + * +@verbatim + =============================================================================== + ##### Peripheral Control functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to control the RCC Clocks + frequencies. + +@endverbatim + * @{ + */ + +/** + * @brief Selects the clock source to output on MCO1 pin(PA8) or on MCO2 pin(PC9). + * @note PA8/PC9 should be configured in alternate function mode. + * @param RCC_MCOx specifies the output direction for the clock source. + * This parameter can be one of the following values: + * @arg RCC_MCO1: Clock source to output on MCO1 pin(PA8). + * @arg RCC_MCO2: Clock source to output on MCO2 pin(PC9). + * @param RCC_MCOSource specifies the clock source to output. + * This parameter can be one of the following values: + * @arg RCC_MCO1SOURCE_HSI: HSI clock selected as MCO1 source + * @arg RCC_MCO1SOURCE_LSE: LSE clock selected as MCO1 source + * @arg RCC_MCO1SOURCE_HSE: HSE clock selected as MCO1 source + * @arg RCC_MCO1SOURCE_PLLCLK: main PLL clock selected as MCO1 source + * @arg RCC_MCO2SOURCE_SYSCLK: System clock (SYSCLK) selected as MCO2 source + * @arg RCC_MCO2SOURCE_PLLI2SCLK: PLLI2S clock selected as MCO2 source, available for all STM32F4 devices except STM32F410xx + * @arg RCC_MCO2SOURCE_I2SCLK: I2SCLK clock selected as MCO2 source, available only for STM32F410Rx devices + * @arg RCC_MCO2SOURCE_HSE: HSE clock selected as MCO2 source + * @arg RCC_MCO2SOURCE_PLLCLK: main PLL clock selected as MCO2 source + * @param RCC_MCODiv specifies the MCOx prescaler. + * This parameter can be one of the following values: + * @arg RCC_MCODIV_1: no division applied to MCOx clock + * @arg RCC_MCODIV_2: division by 2 applied to MCOx clock + * @arg RCC_MCODIV_3: division by 3 applied to MCOx clock + * @arg RCC_MCODIV_4: division by 4 applied to MCOx clock + * @arg RCC_MCODIV_5: division by 5 applied to MCOx clock + * @note For STM32F410Rx devices to output I2SCLK clock on MCO2 you should have + * at last one of the SPI clocks enabled (SPI1, SPI2 or SPI5). + * @retval None + */ +void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv) +{ + GPIO_InitTypeDef GPIO_InitStruct; + /* Check the parameters */ + assert_param(IS_RCC_MCO(RCC_MCOx)); + assert_param(IS_RCC_MCODIV(RCC_MCODiv)); + /* RCC_MCO1 */ + if(RCC_MCOx == RCC_MCO1) + { + assert_param(IS_RCC_MCO1SOURCE(RCC_MCOSource)); + + /* MCO1 Clock Enable */ + __MCO1_CLK_ENABLE(); + + /* Configure the MCO1 pin in alternate function mode */ + GPIO_InitStruct.Pin = MCO1_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF0_MCO; + HAL_GPIO_Init(MCO1_GPIO_PORT, &GPIO_InitStruct); + + /* Mask MCO1 and MCO1PRE[2:0] bits then Select MCO1 clock source and prescaler */ + MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO1 | RCC_CFGR_MCO1PRE), (RCC_MCOSource | RCC_MCODiv)); + + /* This RCC MCO1 enable feature is available only on STM32F410xx devices */ +#if defined(RCC_CFGR_MCO1EN) + __HAL_RCC_MCO1_ENABLE(); +#endif /* RCC_CFGR_MCO1EN */ + } +#if defined(RCC_CFGR_MCO2) + else + { + assert_param(IS_RCC_MCO2SOURCE(RCC_MCOSource)); + + /* MCO2 Clock Enable */ + __MCO2_CLK_ENABLE(); + + /* Configure the MCO2 pin in alternate function mode */ + GPIO_InitStruct.Pin = MCO2_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF0_MCO; + HAL_GPIO_Init(MCO2_GPIO_PORT, &GPIO_InitStruct); + + /* Mask MCO2 and MCO2PRE[2:0] bits then Select MCO2 clock source and prescaler */ + MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO2 | RCC_CFGR_MCO2PRE), (RCC_MCOSource | (RCC_MCODiv << 3U))); + + /* This RCC MCO2 enable feature is available only on STM32F410Rx devices */ +#if defined(RCC_CFGR_MCO2EN) + __HAL_RCC_MCO2_ENABLE(); +#endif /* RCC_CFGR_MCO2EN */ + } +#endif /* RCC_CFGR_MCO2 */ +} + +/** + * @brief Enables the Clock Security System. + * @note If a failure is detected on the HSE oscillator clock, this oscillator + * is automatically disabled and an interrupt is generated to inform the + * software about the failure (Clock Security System Interrupt, CSSI), + * allowing the MCU to perform rescue operations. The CSSI is linked to + * the Cortex-M4 NMI (Non-Maskable Interrupt) exception vector. + * @retval None + */ +void HAL_RCC_EnableCSS(void) +{ + *(__IO uint32_t *) RCC_CR_CSSON_BB = (uint32_t)ENABLE; +} + +/** + * @brief Disables the Clock Security System. + * @retval None + */ +void HAL_RCC_DisableCSS(void) +{ + *(__IO uint32_t *) RCC_CR_CSSON_BB = (uint32_t)DISABLE; +} + +/** + * @brief Returns the SYSCLK frequency + * + * @note The system frequency computed by this function is not the real + * frequency in the chip. It is calculated based on the predefined + * constant and the selected clock source: + * @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*) + * @note If SYSCLK source is HSE, function returns values based on HSE_VALUE(**) + * @note If SYSCLK source is PLL, function returns values based on HSE_VALUE(**) + * or HSI_VALUE(*) multiplied/divided by the PLL factors. + * @note (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value + * 16 MHz) but the real value may vary depending on the variations + * in voltage and temperature. + * @note (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value + * 25 MHz), user has to ensure that HSE_VALUE is same as the real + * frequency of the crystal used. Otherwise, this function may + * have wrong result. + * + * @note The result of this function could be not correct when using fractional + * value for HSE crystal. + * + * @note This function can be used by the user application to compute the + * baudrate for the communication peripherals or configure other parameters. + * + * @note Each time SYSCLK changes, this function must be called to update the + * right SYSCLK value. Otherwise, any configuration based on this function will be incorrect. + * + * + * @retval SYSCLK frequency + */ +__weak uint32_t HAL_RCC_GetSysClockFreq(void) +{ + uint32_t pllm = 0U, pllvco = 0U, pllp = 0U; + uint32_t sysclockfreq = 0U; + + /* Get SYSCLK source -------------------------------------------------------*/ + switch (RCC->CFGR & RCC_CFGR_SWS) + { + case RCC_CFGR_SWS_HSI: /* HSI used as system clock source */ + { + sysclockfreq = HSI_VALUE; + break; + } + case RCC_CFGR_SWS_HSE: /* HSE used as system clock source */ + { + sysclockfreq = HSE_VALUE; + break; + } + case RCC_CFGR_SWS_PLL: /* PLL used as system clock source */ + { + /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLLM) * PLLN + SYSCLK = PLL_VCO / PLLP */ + pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM; + if(__HAL_RCC_GET_PLL_OSCSOURCE() != RCC_PLLSOURCE_HSI) + { + /* HSE used as PLL clock source */ + pllvco = (uint32_t) ((((uint64_t) HSE_VALUE * ((uint64_t) ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos)))) / (uint64_t)pllm); + } + else + { + /* HSI used as PLL clock source */ + pllvco = (uint32_t) ((((uint64_t) HSI_VALUE * ((uint64_t) ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos)))) / (uint64_t)pllm); + } + pllp = ((((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >> RCC_PLLCFGR_PLLP_Pos) + 1U) *2U); + + sysclockfreq = pllvco/pllp; + break; + } + default: + { + sysclockfreq = HSI_VALUE; + break; + } + } + return sysclockfreq; +} + +/** + * @brief Returns the HCLK frequency + * @note Each time HCLK changes, this function must be called to update the + * right HCLK value. Otherwise, any configuration based on this function will be incorrect. + * + * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency + * and updated within this function + * @retval HCLK frequency + */ +uint32_t HAL_RCC_GetHCLKFreq(void) +{ + return SystemCoreClock; +} + +/** + * @brief Returns the PCLK1 frequency + * @note Each time PCLK1 changes, this function must be called to update the + * right PCLK1 value. Otherwise, any configuration based on this function will be incorrect. + * @retval PCLK1 frequency + */ +uint32_t HAL_RCC_GetPCLK1Freq(void) +{ + /* Get HCLK source and Compute PCLK1 frequency ---------------------------*/ + return (HAL_RCC_GetHCLKFreq() >> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE1)>> RCC_CFGR_PPRE1_Pos]); +} + +/** + * @brief Returns the PCLK2 frequency + * @note Each time PCLK2 changes, this function must be called to update the + * right PCLK2 value. Otherwise, any configuration based on this function will be incorrect. + * @retval PCLK2 frequency + */ +uint32_t HAL_RCC_GetPCLK2Freq(void) +{ + /* Get HCLK source and Compute PCLK2 frequency ---------------------------*/ + return (HAL_RCC_GetHCLKFreq()>> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE2)>> RCC_CFGR_PPRE2_Pos]); +} + +/** + * @brief Configures the RCC_OscInitStruct according to the internal + * RCC configuration registers. + * @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that + * will be configured. + * @retval None + */ +__weak void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct) +{ + /* Set all possible values for the Oscillator type parameter ---------------*/ + RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_LSI; + + /* Get the HSE configuration -----------------------------------------------*/ + if((RCC->CR &RCC_CR_HSEBYP) == RCC_CR_HSEBYP) + { + RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS; + } + else if((RCC->CR &RCC_CR_HSEON) == RCC_CR_HSEON) + { + RCC_OscInitStruct->HSEState = RCC_HSE_ON; + } + else + { + RCC_OscInitStruct->HSEState = RCC_HSE_OFF; + } + + /* Get the HSI configuration -----------------------------------------------*/ + if((RCC->CR &RCC_CR_HSION) == RCC_CR_HSION) + { + RCC_OscInitStruct->HSIState = RCC_HSI_ON; + } + else + { + RCC_OscInitStruct->HSIState = RCC_HSI_OFF; + } + + RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->CR &RCC_CR_HSITRIM) >> RCC_CR_HSITRIM_Pos); + + /* Get the LSE configuration -----------------------------------------------*/ + if((RCC->BDCR &RCC_BDCR_LSEBYP) == RCC_BDCR_LSEBYP) + { + RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS; + } + else if((RCC->BDCR &RCC_BDCR_LSEON) == RCC_BDCR_LSEON) + { + RCC_OscInitStruct->LSEState = RCC_LSE_ON; + } + else + { + RCC_OscInitStruct->LSEState = RCC_LSE_OFF; + } + + /* Get the LSI configuration -----------------------------------------------*/ + if((RCC->CSR &RCC_CSR_LSION) == RCC_CSR_LSION) + { + RCC_OscInitStruct->LSIState = RCC_LSI_ON; + } + else + { + RCC_OscInitStruct->LSIState = RCC_LSI_OFF; + } + + /* Get the PLL configuration -----------------------------------------------*/ + if((RCC->CR &RCC_CR_PLLON) == RCC_CR_PLLON) + { + RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON; + } + else + { + RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF; + } + RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC); + RCC_OscInitStruct->PLL.PLLM = (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM); + RCC_OscInitStruct->PLL.PLLN = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos); + RCC_OscInitStruct->PLL.PLLP = (uint32_t)((((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) + RCC_PLLCFGR_PLLP_0) << 1U) >> RCC_PLLCFGR_PLLP_Pos); + RCC_OscInitStruct->PLL.PLLQ = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLQ) >> RCC_PLLCFGR_PLLQ_Pos); +} + +/** + * @brief Configures the RCC_ClkInitStruct according to the internal + * RCC configuration registers. + * @param RCC_ClkInitStruct pointer to an RCC_ClkInitTypeDef structure that + * will be configured. + * @param pFLatency Pointer on the Flash Latency. + * @retval None + */ +void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency) +{ + /* Set all possible values for the Clock type parameter --------------------*/ + RCC_ClkInitStruct->ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; + + /* Get the SYSCLK configuration --------------------------------------------*/ + RCC_ClkInitStruct->SYSCLKSource = (uint32_t)(RCC->CFGR & RCC_CFGR_SW); + + /* Get the HCLK configuration ----------------------------------------------*/ + RCC_ClkInitStruct->AHBCLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_HPRE); + + /* Get the APB1 configuration ----------------------------------------------*/ + RCC_ClkInitStruct->APB1CLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_PPRE1); + + /* Get the APB2 configuration ----------------------------------------------*/ + RCC_ClkInitStruct->APB2CLKDivider = (uint32_t)((RCC->CFGR & RCC_CFGR_PPRE2) >> 3U); + + /* Get the Flash Wait State (Latency) configuration ------------------------*/ + *pFLatency = (uint32_t)(FLASH->ACR & FLASH_ACR_LATENCY); +} + +/** + * @brief This function handles the RCC CSS interrupt request. + * @note This API should be called under the NMI_Handler(). + * @retval None + */ +void HAL_RCC_NMI_IRQHandler(void) +{ + /* Check RCC CSSF flag */ + if(__HAL_RCC_GET_IT(RCC_IT_CSS)) + { + /* RCC Clock Security System interrupt user callback */ + HAL_RCC_CSSCallback(); + + /* Clear RCC CSS pending bit */ + __HAL_RCC_CLEAR_IT(RCC_IT_CSS); + } +} + +/** + * @brief RCC Clock Security System interrupt callback + * @retval None + */ +__weak void HAL_RCC_CSSCallback(void) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_RCC_CSSCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_RCC_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/