Mercurial > public > ostc4
diff Common/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_mmc.c @ 128:c78bcbd5deda FlipDisplay
Added current STM32 standandard libraries in version independend folder structure
author | Ideenmodellierer |
---|---|
date | Sun, 17 Feb 2019 21:12:22 +0100 |
parents | |
children |
line wrap: on
line diff
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/Common/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_mmc.c Sun Feb 17 21:12:22 2019 +0100 @@ -0,0 +1,2602 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_mmc.c + * @author MCD Application Team + * @brief MMC card HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Secure Digital (MMC) peripheral: + * + Initialization and de-initialization functions + * + IO operation functions + * + Peripheral Control functions + * + MMC card Control functions + * + @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + [..] + This driver implements a high level communication layer for read and write from/to + this memory. The needed STM32 hardware resources (SDMMC and GPIO) are performed by + the user in HAL_MMC_MspInit() function (MSP layer). + Basically, the MSP layer configuration should be the same as we provide in the + examples. + You can easily tailor this configuration according to hardware resources. + + [..] + This driver is a generic layered driver for SDMMC memories which uses the HAL + SDMMC driver functions to interface with MMC and eMMC cards devices. + It is used as follows: + + (#)Initialize the SDMMC low level resources by implement the HAL_MMC_MspInit() API: + (##) Enable the SDMMC interface clock using __HAL_RCC_SDMMC_CLK_ENABLE(); + (##) SDMMC pins configuration for MMC card + (+++) Enable the clock for the SDMMC GPIOs using the functions __HAL_RCC_GPIOx_CLK_ENABLE(); + (+++) Configure these SDMMC pins as alternate function pull-up using HAL_GPIO_Init() + and according to your pin assignment; + (##) DMA Configuration if you need to use DMA process (HAL_MMC_ReadBlocks_DMA() + and HAL_MMC_WriteBlocks_DMA() APIs). + (+++) Enable the DMAx interface clock using __HAL_RCC_DMAx_CLK_ENABLE(); + (+++) Configure the DMA using the function HAL_DMA_Init() with predeclared and filled. + (##) NVIC configuration if you need to use interrupt process when using DMA transfer. + (+++) Configure the SDMMC and DMA interrupt priorities using functions + HAL_NVIC_SetPriority(); DMA priority is superior to SDMMC's priority + (+++) Enable the NVIC DMA and SDMMC IRQs using function HAL_NVIC_EnableIRQ() + (+++) SDMMC interrupts are managed using the macros __HAL_MMC_ENABLE_IT() + and __HAL_MMC_DISABLE_IT() inside the communication process. + (+++) SDMMC interrupts pending bits are managed using the macros __HAL_MMC_GET_IT() + and __HAL_MMC_CLEAR_IT() + (##) NVIC configuration if you need to use interrupt process (HAL_MMC_ReadBlocks_IT() + and HAL_MMC_WriteBlocks_IT() APIs). + (+++) Configure the SDMMC interrupt priorities using function + HAL_NVIC_SetPriority(); + (+++) Enable the NVIC SDMMC IRQs using function HAL_NVIC_EnableIRQ() + (+++) SDMMC interrupts are managed using the macros __HAL_MMC_ENABLE_IT() + and __HAL_MMC_DISABLE_IT() inside the communication process. + (+++) SDMMC interrupts pending bits are managed using the macros __HAL_MMC_GET_IT() + and __HAL_MMC_CLEAR_IT() + (#) At this stage, you can perform MMC read/write/erase operations after MMC card initialization + + + *** MMC Card Initialization and configuration *** + ================================================ + [..] + To initialize the MMC Card, use the HAL_MMC_Init() function. It Initializes + SDMMC IP (STM32 side) and the MMC Card, and put it into StandBy State (Ready for data transfer). + This function provide the following operations: + + (#) Initialize the SDMMC peripheral interface with defaullt configuration. + The initialization process is done at 400KHz. You can change or adapt + this frequency by adjusting the "ClockDiv" field. + The MMC Card frequency (SDMMC_CK) is computed as follows: + + SDMMC_CK = SDMMCCLK / (ClockDiv + 2) + + In initialization mode and according to the MMC Card standard, + make sure that the SDMMC_CK frequency doesn't exceed 400KHz. + + This phase of initialization is done through SDMMC_Init() and + SDMMC_PowerState_ON() SDMMC low level APIs. + + (#) Initialize the MMC card. The API used is HAL_MMC_InitCard(). + This phase allows the card initialization and identification + and check the MMC Card type (Standard Capacity or High Capacity) + The initialization flow is compatible with MMC standard. + + This API (HAL_MMC_InitCard()) could be used also to reinitialize the card in case + of plug-off plug-in. + + (#) Configure the MMC Card Data transfer frequency. By Default, the card transfer + frequency is set to 24MHz. You can change or adapt this frequency by adjusting + the "ClockDiv" field. + In transfer mode and according to the MMC Card standard, make sure that the + SDMMC_CK frequency doesn't exceed 25MHz and 50MHz in High-speed mode switch. + To be able to use a frequency higher than 24MHz, you should use the SDMMC + peripheral in bypass mode. Refer to the corresponding reference manual + for more details. + + (#) Select the corresponding MMC Card according to the address read with the step 2. + + (#) Configure the MMC Card in wide bus mode: 4-bits data. + + *** MMC Card Read operation *** + ============================== + [..] + (+) You can read from MMC card in polling mode by using function HAL_MMC_ReadBlocks(). + This function allows the read of 512 bytes blocks. + You can choose either one block read operation or multiple block read operation + by adjusting the "NumberOfBlocks" parameter. + After this, you have to ensure that the transfer is done correctly. The check is done + through HAL_MMC_GetCardState() function for MMC card state. + + (+) You can read from MMC card in DMA mode by using function HAL_MMC_ReadBlocks_DMA(). + This function allows the read of 512 bytes blocks. + You can choose either one block read operation or multiple block read operation + by adjusting the "NumberOfBlocks" parameter. + After this, you have to ensure that the transfer is done correctly. The check is done + through HAL_MMC_GetCardState() function for MMC card state. + You could also check the DMA transfer process through the MMC Rx interrupt event. + + (+) You can read from MMC card in Interrupt mode by using function HAL_MMC_ReadBlocks_IT(). + This function allows the read of 512 bytes blocks. + You can choose either one block read operation or multiple block read operation + by adjusting the "NumberOfBlocks" parameter. + After this, you have to ensure that the transfer is done correctly. The check is done + through HAL_MMC_GetCardState() function for MMC card state. + You could also check the IT transfer process through the MMC Rx interrupt event. + + *** MMC Card Write operation *** + =============================== + [..] + (+) You can write to MMC card in polling mode by using function HAL_MMC_WriteBlocks(). + This function allows the read of 512 bytes blocks. + You can choose either one block read operation or multiple block read operation + by adjusting the "NumberOfBlocks" parameter. + After this, you have to ensure that the transfer is done correctly. The check is done + through HAL_MMC_GetCardState() function for MMC card state. + + (+) You can write to MMC card in DMA mode by using function HAL_MMC_WriteBlocks_DMA(). + This function allows the read of 512 bytes blocks. + You can choose either one block read operation or multiple block read operation + by adjusting the "NumberOfBlocks" parameter. + After this, you have to ensure that the transfer is done correctly. The check is done + through HAL_MMC_GetCardState() function for MMC card state. + You could also check the DMA transfer process through the MMC Tx interrupt event. + + (+) You can write to MMC card in Interrupt mode by using function HAL_MMC_WriteBlocks_IT(). + This function allows the read of 512 bytes blocks. + You can choose either one block read operation or multiple block read operation + by adjusting the "NumberOfBlocks" parameter. + After this, you have to ensure that the transfer is done correctly. The check is done + through HAL_MMC_GetCardState() function for MMC card state. + You could also check the IT transfer process through the MMC Tx interrupt event. + + *** MMC card status *** + ====================== + [..] + (+) The MMC Status contains status bits that are related to the MMC Memory + Card proprietary features. To get MMC card status use the HAL_MMC_GetCardStatus(). + + *** MMC card information *** + =========================== + [..] + (+) To get MMC card information, you can use the function HAL_MMC_GetCardInfo(). + It returns useful information about the MMC card such as block size, card type, + block number ... + + *** MMC card CSD register *** + ============================ + [..] + (+) The HAL_MMC_GetCardCSD() API allows to get the parameters of the CSD register. + Some of the CSD parameters are useful for card initialization and identification. + + *** MMC card CID register *** + ============================ + [..] + (+) The HAL_MMC_GetCardCID() API allows to get the parameters of the CID register. + Some of the CID parameters are useful for card initialization and identification. + + *** MMC HAL driver macros list *** + ================================== + [..] + Below the list of most used macros in MMC HAL driver. + + (+) __HAL_MMC_ENABLE : Enable the MMC device + (+) __HAL_MMC_DISABLE : Disable the MMC device + (+) __HAL_MMC_DMA_ENABLE: Enable the SDMMC DMA transfer + (+) __HAL_MMC_DMA_DISABLE: Disable the SDMMC DMA transfer + (+) __HAL_MMC_ENABLE_IT: Enable the MMC device interrupt + (+) __HAL_MMC_DISABLE_IT: Disable the MMC device interrupt + (+) __HAL_MMC_GET_FLAG:Check whether the specified MMC flag is set or not + (+) __HAL_MMC_CLEAR_FLAG: Clear the MMC's pending flags + + [..] + (@) You can refer to the MMC HAL driver header file for more useful macros + + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f4xx_hal.h" + +/** @addtogroup STM32F4xx_HAL_Driver + * @{ + */ + +/** @addtogroup MMC + * @{ + */ + +#ifdef HAL_MMC_MODULE_ENABLED + +#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \ + defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \ + defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \ + defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ + defined(STM32F412Rx) || defined(STM32F412Cx) || defined(STM32F413xx) || defined(STM32F423xx) + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @addtogroup MMC_Private_Defines + * @{ + */ + +/** + * @} + */ + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ +/** @defgroup MMC_Private_Functions MMC Private Functions + * @{ + */ +static uint32_t MMC_InitCard(MMC_HandleTypeDef *hmmc); +static uint32_t MMC_PowerON(MMC_HandleTypeDef *hmmc); +static uint32_t MMC_SendStatus(MMC_HandleTypeDef *hmmc, uint32_t *pCardStatus); +static HAL_StatusTypeDef MMC_PowerOFF(MMC_HandleTypeDef *hmmc); +static HAL_StatusTypeDef MMC_Write_IT(MMC_HandleTypeDef *hmmc); +static HAL_StatusTypeDef MMC_Read_IT(MMC_HandleTypeDef *hmmc); +static void MMC_DMATransmitCplt(DMA_HandleTypeDef *hdma); +static void MMC_DMAReceiveCplt(DMA_HandleTypeDef *hdma); +static void MMC_DMAError(DMA_HandleTypeDef *hdma); +static void MMC_DMATxAbort(DMA_HandleTypeDef *hdma); +static void MMC_DMARxAbort(DMA_HandleTypeDef *hdma); +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup MMC_Exported_Functions + * @{ + */ + +/** @addtogroup MMC_Exported_Functions_Group1 + * @brief Initialization and de-initialization functions + * +@verbatim + ============================================================================== + ##### Initialization and de-initialization functions ##### + ============================================================================== + [..] + This section provides functions allowing to initialize/de-initialize the MMC + card device to be ready for use. + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the MMC according to the specified parameters in the + MMC_HandleTypeDef and create the associated handle. + * @param hmmc Pointer to the MMC handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_Init(MMC_HandleTypeDef *hmmc) +{ + /* Check the MMC handle allocation */ + if(hmmc == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_SDIO_ALL_INSTANCE(hmmc->Instance)); + assert_param(IS_SDIO_CLOCK_EDGE(hmmc->Init.ClockEdge)); + assert_param(IS_SDIO_CLOCK_BYPASS(hmmc->Init.ClockBypass)); + assert_param(IS_SDIO_CLOCK_POWER_SAVE(hmmc->Init.ClockPowerSave)); + assert_param(IS_SDIO_BUS_WIDE(hmmc->Init.BusWide)); + assert_param(IS_SDIO_HARDWARE_FLOW_CONTROL(hmmc->Init.HardwareFlowControl)); + assert_param(IS_SDIO_CLKDIV(hmmc->Init.ClockDiv)); + + if(hmmc->State == HAL_MMC_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + hmmc->Lock = HAL_UNLOCKED; + /* Init the low level hardware : GPIO, CLOCK, CORTEX...etc */ + HAL_MMC_MspInit(hmmc); + } + + hmmc->State = HAL_MMC_STATE_BUSY; + + /* Initialize the Card parameters */ + HAL_MMC_InitCard(hmmc); + + /* Initialize the error code */ + hmmc->ErrorCode = HAL_DMA_ERROR_NONE; + + /* Initialize the MMC operation */ + hmmc->Context = MMC_CONTEXT_NONE; + + /* Initialize the MMC state */ + hmmc->State = HAL_MMC_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Initializes the MMC Card. + * @param hmmc Pointer to MMC handle + * @note This function initializes the MMC card. It could be used when a card + re-initialization is needed. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_InitCard(MMC_HandleTypeDef *hmmc) +{ + uint32_t errorstate = HAL_MMC_ERROR_NONE; + MMC_InitTypeDef Init; + + /* Default SDMMC peripheral configuration for MMC card initialization */ + Init.ClockEdge = SDIO_CLOCK_EDGE_RISING; + Init.ClockBypass = SDIO_CLOCK_BYPASS_DISABLE; + Init.ClockPowerSave = SDIO_CLOCK_POWER_SAVE_DISABLE; + Init.BusWide = SDIO_BUS_WIDE_1B; + Init.HardwareFlowControl = SDIO_HARDWARE_FLOW_CONTROL_DISABLE; + Init.ClockDiv = SDIO_INIT_CLK_DIV; + + /* Initialize SDMMC peripheral interface with default configuration */ + SDIO_Init(hmmc->Instance, Init); + + /* Disable SDMMC Clock */ + __HAL_MMC_DISABLE(hmmc); + + /* Set Power State to ON */ + SDIO_PowerState_ON(hmmc->Instance); + + /* Enable SDMMC Clock */ + __HAL_MMC_ENABLE(hmmc); + + /* Required power up waiting time before starting the SD initialization + sequence */ + HAL_Delay(2U); + + /* Identify card operating voltage */ + errorstate = MMC_PowerON(hmmc); + if(errorstate != HAL_MMC_ERROR_NONE) + { + hmmc->State = HAL_MMC_STATE_READY; + hmmc->ErrorCode |= errorstate; + return HAL_ERROR; + } + + /* Card initialization */ + errorstate = MMC_InitCard(hmmc); + if(errorstate != HAL_MMC_ERROR_NONE) + { + hmmc->State = HAL_MMC_STATE_READY; + hmmc->ErrorCode |= errorstate; + return HAL_ERROR; + } + + return HAL_OK; +} + +/** + * @brief De-Initializes the MMC card. + * @param hmmc Pointer to MMC handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_DeInit(MMC_HandleTypeDef *hmmc) +{ + /* Check the MMC handle allocation */ + if(hmmc == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_SDIO_ALL_INSTANCE(hmmc->Instance)); + + hmmc->State = HAL_MMC_STATE_BUSY; + + /* Set SD power state to off */ + MMC_PowerOFF(hmmc); + + /* De-Initialize the MSP layer */ + HAL_MMC_MspDeInit(hmmc); + + hmmc->ErrorCode = HAL_MMC_ERROR_NONE; + hmmc->State = HAL_MMC_STATE_RESET; + + return HAL_OK; +} + + +/** + * @brief Initializes the MMC MSP. + * @param hmmc Pointer to MMC handle + * @retval None + */ +__weak void HAL_MMC_MspInit(MMC_HandleTypeDef *hmmc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hmmc); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_MMC_MspInit could be implemented in the user file + */ +} + +/** + * @brief De-Initialize MMC MSP. + * @param hmmc Pointer to MMC handle + * @retval None + */ +__weak void HAL_MMC_MspDeInit(MMC_HandleTypeDef *hmmc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hmmc); + + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_MMC_MspDeInit could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @addtogroup MMC_Exported_Functions_Group2 + * @brief Data transfer functions + * +@verbatim + ============================================================================== + ##### IO operation functions ##### + ============================================================================== + [..] + This subsection provides a set of functions allowing to manage the data + transfer from/to MMC card. + +@endverbatim + * @{ + */ + +/** + * @brief Reads block(s) from a specified address in a card. The Data transfer + * is managed by polling mode. + * @note This API should be followed by a check on the card state through + * HAL_MMC_GetCardState(). + * @param hmmc Pointer to MMC handle + * @param pData pointer to the buffer that will contain the received data + * @param BlockAdd Block Address from where data is to be read + * @param NumberOfBlocks Number of MMC blocks to read + * @param Timeout Specify timeout value + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_ReadBlocks(MMC_HandleTypeDef *hmmc, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout) +{ + SDIO_DataInitTypeDef config; + uint32_t errorstate = HAL_MMC_ERROR_NONE; + uint32_t tickstart = HAL_GetTick(); + uint32_t count = 0U, *tempbuff = (uint32_t *)pData; + + if(NULL == pData) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_PARAM; + return HAL_ERROR; + } + + if(hmmc->State == HAL_MMC_STATE_READY) + { + hmmc->ErrorCode = HAL_DMA_ERROR_NONE; + + if((BlockAdd + NumberOfBlocks) > (hmmc->MmcCard.LogBlockNbr)) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_ADDR_OUT_OF_RANGE; + return HAL_ERROR; + } + + hmmc->State = HAL_MMC_STATE_BUSY; + + /* Initialize data control register */ + hmmc->Instance->DCTRL = 0U; + + /* Check the Card capacity in term of Logical number of blocks */ + if ((hmmc->MmcCard.LogBlockNbr) < CAPACITY) + { + BlockAdd *= 512U; + } + + /* Set Block Size for Card */ + errorstate = SDMMC_CmdBlockLength(hmmc->Instance, BLOCKSIZE); + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDMMC_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Configure the MMC DPSM (Data Path State Machine) */ + config.DataTimeOut = SDMMC_DATATIMEOUT; + config.DataLength = NumberOfBlocks * BLOCKSIZE; + config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B; + config.TransferDir = SDIO_TRANSFER_DIR_TO_SDIO; + config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; + config.DPSM = SDIO_DPSM_ENABLE; + SDIO_ConfigData(hmmc->Instance, &config); + + /* Read block(s) in polling mode */ + if(NumberOfBlocks > 1U) + { + hmmc->Context = MMC_CONTEXT_READ_MULTIPLE_BLOCK; + + /* Read Multi Block command */ + errorstate = SDMMC_CmdReadMultiBlock(hmmc->Instance, BlockAdd); + } + else + { + hmmc->Context = MMC_CONTEXT_READ_SINGLE_BLOCK; + + /* Read Single Block command */ + errorstate = SDMMC_CmdReadSingleBlock(hmmc->Instance, BlockAdd); + } + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDMMC_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Poll on SDMMC flags */ +#ifdef SDIO_STA_STBITERR + while(!__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_RXOVERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_DATAEND | SDIO_STA_STBITERR)) +#else /* SDIO_STA_STBITERR not defined */ + while(!__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_RXOVERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_DATAEND)) +#endif /* SDIO_STA_STBITERR */ + { + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_RXFIFOHF)) + { + /* Read data from SDMMC Rx FIFO */ + for(count = 0U; count < 8U; count++) + { + *(tempbuff + count) = SDIO_ReadFIFO(hmmc->Instance); + } + tempbuff += 8U; + } + + if((Timeout == 0U)||((HAL_GetTick()-tickstart) >= Timeout)) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDMMC_STATIC_FLAGS); + hmmc->ErrorCode |= HAL_MMC_ERROR_TIMEOUT; + hmmc->State= HAL_MMC_STATE_READY; + return HAL_TIMEOUT; + } + } + + /* Send stop transmission command in case of multiblock read */ + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_DATAEND) && (NumberOfBlocks > 1U)) + { + /* Send stop transmission command */ + errorstate = SDMMC_CmdStopTransfer(hmmc->Instance); + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDMMC_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + } + + /* Get error state */ + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_DTIMEOUT)) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDMMC_STATIC_FLAGS); + hmmc->ErrorCode |= HAL_MMC_ERROR_DATA_TIMEOUT; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + else if(__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_DCRCFAIL)) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDMMC_STATIC_FLAGS); + hmmc->ErrorCode |= HAL_MMC_ERROR_DATA_CRC_FAIL; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + else if(__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_RXOVERR)) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDMMC_STATIC_FLAGS); + hmmc->ErrorCode |= HAL_MMC_ERROR_RX_OVERRUN; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Empty FIFO if there is still any data */ + while ((__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_RXDAVL))) + { + *tempbuff = SDIO_ReadFIFO(hmmc->Instance); + tempbuff++; + + if((Timeout == 0U)||((HAL_GetTick()-tickstart) >= Timeout)) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDMMC_STATIC_FLAGS); + hmmc->ErrorCode |= HAL_MMC_ERROR_TIMEOUT; + hmmc->State= HAL_MMC_STATE_READY; + return HAL_ERROR; + } + } + + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDMMC_STATIC_FLAGS); + + hmmc->State = HAL_MMC_STATE_READY; + + return HAL_OK; + } + else + { + hmmc->ErrorCode |= HAL_MMC_ERROR_BUSY; + return HAL_ERROR; + } +} + +/** + * @brief Allows to write block(s) to a specified address in a card. The Data + * transfer is managed by polling mode. + * @note This API should be followed by a check on the card state through + * HAL_MMC_GetCardState(). + * @param hmmc Pointer to MMC handle + * @param pData pointer to the buffer that will contain the data to transmit + * @param BlockAdd Block Address where data will be written + * @param NumberOfBlocks Number of MMC blocks to write + * @param Timeout Specify timeout value + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_WriteBlocks(MMC_HandleTypeDef *hmmc, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout) +{ + SDIO_DataInitTypeDef config; + uint32_t errorstate = HAL_MMC_ERROR_NONE; + uint32_t tickstart = HAL_GetTick(); + uint32_t count = 0U; + uint32_t *tempbuff = (uint32_t *)pData; + + if(NULL == pData) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_PARAM; + return HAL_ERROR; + } + + if(hmmc->State == HAL_MMC_STATE_READY) + { + hmmc->ErrorCode = HAL_DMA_ERROR_NONE; + + if((BlockAdd + NumberOfBlocks) > (hmmc->MmcCard.LogBlockNbr)) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_ADDR_OUT_OF_RANGE; + return HAL_ERROR; + } + + hmmc->State = HAL_MMC_STATE_BUSY; + + /* Initialize data control register */ + hmmc->Instance->DCTRL = 0U; + + /* Check the Card capacity in term of Logical number of blocks */ + if ((hmmc->MmcCard.LogBlockNbr) < CAPACITY) + { + BlockAdd *= 512U; + } + + /* Set Block Size for Card */ + errorstate = SDMMC_CmdBlockLength(hmmc->Instance, BLOCKSIZE); + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Write Blocks in Polling mode */ + if(NumberOfBlocks > 1U) + { + hmmc->Context = MMC_CONTEXT_WRITE_MULTIPLE_BLOCK; + + /* Write Multi Block command */ + errorstate = SDMMC_CmdWriteMultiBlock(hmmc->Instance, BlockAdd); + } + else + { + hmmc->Context = MMC_CONTEXT_WRITE_SINGLE_BLOCK; + + /* Write Single Block command */ + errorstate = SDMMC_CmdWriteSingleBlock(hmmc->Instance, BlockAdd); + } + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Configure the MMC DPSM (Data Path State Machine) */ + config.DataTimeOut = SDMMC_DATATIMEOUT; + config.DataLength = NumberOfBlocks * BLOCKSIZE; + config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B; + config.TransferDir = SDIO_TRANSFER_DIR_TO_CARD; + config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; + config.DPSM = SDIO_DPSM_ENABLE; + SDIO_ConfigData(hmmc->Instance, &config); + + /* Write block(s) in polling mode */ +#ifdef SDIO_STA_STBITERR + while(!__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_TXUNDERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_DATAEND | SDIO_FLAG_STBITERR)) +#else /* SDIO_STA_STBITERR not defined */ + while(!__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_TXUNDERR | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_DTIMEOUT | SDIO_FLAG_DATAEND)) +#endif /* SDIO_STA_STBITERR */ + { + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_TXFIFOHE)) + { + /* Write data to SDIO Tx FIFO */ + for(count = 0U; count < 8U; count++) + { + SDIO_WriteFIFO(hmmc->Instance, (tempbuff + count)); + } + tempbuff += 8U; + } + + if((Timeout == 0U)||((HAL_GetTick()-tickstart) >= Timeout)) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_TIMEOUT; + } + } + + /* Send stop transmission command in case of multiblock write */ + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_DATAEND) && (NumberOfBlocks > 1U)) + { + /* Send stop transmission command */ + errorstate = SDMMC_CmdStopTransfer(hmmc->Instance); + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + } + + /* Get error state */ + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_DTIMEOUT)) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= HAL_MMC_ERROR_DATA_TIMEOUT; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + else if(__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_DCRCFAIL)) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= HAL_MMC_ERROR_DATA_CRC_FAIL; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + else if(__HAL_MMC_GET_FLAG(hmmc, SDIO_FLAG_TXUNDERR)) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= HAL_MMC_ERROR_TX_UNDERRUN; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + + hmmc->State = HAL_MMC_STATE_READY; + + return HAL_OK; + } + else + { + hmmc->ErrorCode |= HAL_MMC_ERROR_BUSY; + return HAL_ERROR; + } +} + +/** + * @brief Reads block(s) from a specified address in a card. The Data transfer + * is managed in interrupt mode. + * @note This API should be followed by a check on the card state through + * HAL_MMC_GetCardState(). + * @note You could also check the IT transfer process through the MMC Rx + * interrupt event. + * @param hmmc Pointer to MMC handle + * @param pData Pointer to the buffer that will contain the received data + * @param BlockAdd Block Address from where data is to be read + * @param NumberOfBlocks Number of blocks to read. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_ReadBlocks_IT(MMC_HandleTypeDef *hmmc, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks) +{ + SDIO_DataInitTypeDef config; + uint32_t errorstate = HAL_MMC_ERROR_NONE; + + if(NULL == pData) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_PARAM; + return HAL_ERROR; + } + + if(hmmc->State == HAL_MMC_STATE_READY) + { + hmmc->ErrorCode = HAL_DMA_ERROR_NONE; + + if((BlockAdd + NumberOfBlocks) > (hmmc->MmcCard.LogBlockNbr)) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_ADDR_OUT_OF_RANGE; + return HAL_ERROR; + } + + hmmc->State = HAL_MMC_STATE_BUSY; + + /* Initialize data control register */ + hmmc->Instance->DCTRL = 0U; + + hmmc->pRxBuffPtr = (uint32_t *)pData; + hmmc->RxXferSize = BLOCKSIZE * NumberOfBlocks; + + __HAL_MMC_ENABLE_IT(hmmc, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_RXOVERR | SDIO_IT_DATAEND | SDIO_FLAG_RXFIFOHF)); + + /* Check the Card capacity in term of Logical number of blocks */ + if ((hmmc->MmcCard.LogBlockNbr) < CAPACITY) + { + BlockAdd *= 512U; + } + + /* Configure the MMC DPSM (Data Path State Machine) */ + config.DataTimeOut = SDMMC_DATATIMEOUT; + config.DataLength = BLOCKSIZE * NumberOfBlocks; + config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B; + config.TransferDir = SDIO_TRANSFER_DIR_TO_SDIO; + config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; + config.DPSM = SDIO_DPSM_ENABLE; + SDIO_ConfigData(hmmc->Instance, &config); + + /* Set Block Size for Card */ + errorstate = SDMMC_CmdBlockLength(hmmc->Instance, BLOCKSIZE); + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Read Blocks in IT mode */ + if(NumberOfBlocks > 1U) + { + hmmc->Context = (MMC_CONTEXT_READ_MULTIPLE_BLOCK | MMC_CONTEXT_IT); + + /* Read Multi Block command */ + errorstate = SDMMC_CmdReadMultiBlock(hmmc->Instance, BlockAdd); + } + else + { + hmmc->Context = (MMC_CONTEXT_READ_SINGLE_BLOCK | MMC_CONTEXT_IT); + + /* Read Single Block command */ + errorstate = SDMMC_CmdReadSingleBlock(hmmc->Instance, BlockAdd); + } + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Writes block(s) to a specified address in a card. The Data transfer + * is managed in interrupt mode. + * @note This API should be followed by a check on the card state through + * HAL_MMC_GetCardState(). + * @note You could also check the IT transfer process through the MMC Tx + * interrupt event. + * @param hmmc Pointer to MMC handle + * @param pData Pointer to the buffer that will contain the data to transmit + * @param BlockAdd Block Address where data will be written + * @param NumberOfBlocks Number of blocks to write + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_WriteBlocks_IT(MMC_HandleTypeDef *hmmc, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks) +{ + SDIO_DataInitTypeDef config; + uint32_t errorstate = HAL_MMC_ERROR_NONE; + + if(NULL == pData) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_PARAM; + return HAL_ERROR; + } + + if(hmmc->State == HAL_MMC_STATE_READY) + { + hmmc->ErrorCode = HAL_DMA_ERROR_NONE; + + if((BlockAdd + NumberOfBlocks) > (hmmc->MmcCard.LogBlockNbr)) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_ADDR_OUT_OF_RANGE; + return HAL_ERROR; + } + + hmmc->State = HAL_MMC_STATE_BUSY; + + /* Initialize data control register */ + hmmc->Instance->DCTRL = 0U; + + hmmc->pTxBuffPtr = (uint32_t *)pData; + hmmc->TxXferSize = BLOCKSIZE * NumberOfBlocks; + + /* Enable transfer interrupts */ + __HAL_MMC_ENABLE_IT(hmmc, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_TXUNDERR | SDIO_IT_DATAEND | SDIO_FLAG_TXFIFOHE)); + + /* Check the Card capacity in term of Logical number of blocks */ + if ((hmmc->MmcCard.LogBlockNbr) < CAPACITY) + { + BlockAdd *= 512U; + } + + /* Set Block Size for Card */ + errorstate = SDMMC_CmdBlockLength(hmmc->Instance, BLOCKSIZE); + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Write Blocks in Polling mode */ + if(NumberOfBlocks > 1U) + { + hmmc->Context = (MMC_CONTEXT_WRITE_MULTIPLE_BLOCK| MMC_CONTEXT_IT); + + /* Write Multi Block command */ + errorstate = SDMMC_CmdWriteMultiBlock(hmmc->Instance, BlockAdd); + } + else + { + hmmc->Context = (MMC_CONTEXT_WRITE_SINGLE_BLOCK | MMC_CONTEXT_IT); + + /* Write Single Block command */ + errorstate = SDMMC_CmdWriteSingleBlock(hmmc->Instance, BlockAdd); + } + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Configure the MMC DPSM (Data Path State Machine) */ + config.DataTimeOut = SDMMC_DATATIMEOUT; + config.DataLength = BLOCKSIZE * NumberOfBlocks; + config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B; + config.TransferDir = SDIO_TRANSFER_DIR_TO_CARD; + config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; + config.DPSM = SDIO_DPSM_ENABLE; + SDIO_ConfigData(hmmc->Instance, &config); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Reads block(s) from a specified address in a card. The Data transfer + * is managed by DMA mode. + * @note This API should be followed by a check on the card state through + * HAL_MMC_GetCardState(). + * @note You could also check the DMA transfer process through the MMC Rx + * interrupt event. + * @param hmmc Pointer MMC handle + * @param pData Pointer to the buffer that will contain the received data + * @param BlockAdd Block Address from where data is to be read + * @param NumberOfBlocks Number of blocks to read. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_ReadBlocks_DMA(MMC_HandleTypeDef *hmmc, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks) +{ + SDIO_DataInitTypeDef config; + uint32_t errorstate = HAL_MMC_ERROR_NONE; + + if(NULL == pData) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_PARAM; + return HAL_ERROR; + } + + if(hmmc->State == HAL_MMC_STATE_READY) + { + hmmc->ErrorCode = HAL_DMA_ERROR_NONE; + + if((BlockAdd + NumberOfBlocks) > (hmmc->MmcCard.LogBlockNbr)) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_ADDR_OUT_OF_RANGE; + return HAL_ERROR; + } + + hmmc->State = HAL_MMC_STATE_BUSY; + + /* Initialize data control register */ + hmmc->Instance->DCTRL = 0U; + +#ifdef SDIO_STA_STBITER + __HAL_MMC_ENABLE_IT(hmmc, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_RXOVERR | SDIO_IT_DATAEND | SDIO_IT_STBITERR)); +#else /* SDIO_STA_STBITERR not defined */ + __HAL_MMC_ENABLE_IT(hmmc, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_RXOVERR | SDIO_IT_DATAEND)); +#endif /* SDIO_STA_STBITERR */ + + /* Set the DMA transfer complete callback */ + hmmc->hdmarx->XferCpltCallback = MMC_DMAReceiveCplt; + + /* Set the DMA error callback */ + hmmc->hdmarx->XferErrorCallback = MMC_DMAError; + + /* Set the DMA Abort callback */ + hmmc->hdmarx->XferAbortCallback = NULL; + + /* Enable the DMA Channel */ + HAL_DMA_Start_IT(hmmc->hdmarx, (uint32_t)&hmmc->Instance->FIFO, (uint32_t)pData, (uint32_t)(BLOCKSIZE * NumberOfBlocks)/4); + + /* Enable MMC DMA transfer */ + __HAL_MMC_DMA_ENABLE(hmmc); + + /* Check the Card capacity in term of Logical number of blocks */ + if ((hmmc->MmcCard.LogBlockNbr) < CAPACITY) + { + BlockAdd *= 512U; + } + + /* Configure the MMC DPSM (Data Path State Machine) */ + config.DataTimeOut = SDMMC_DATATIMEOUT; + config.DataLength = BLOCKSIZE * NumberOfBlocks; + config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B; + config.TransferDir = SDIO_TRANSFER_DIR_TO_SDIO; + config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; + config.DPSM = SDIO_DPSM_ENABLE; + SDIO_ConfigData(hmmc->Instance, &config); + + /* Set Block Size for Card */ + errorstate = SDMMC_CmdBlockLength(hmmc->Instance, BLOCKSIZE); + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Read Blocks in DMA mode */ + if(NumberOfBlocks > 1U) + { + hmmc->Context = (MMC_CONTEXT_READ_MULTIPLE_BLOCK | MMC_CONTEXT_DMA); + + /* Read Multi Block command */ + errorstate = SDMMC_CmdReadMultiBlock(hmmc->Instance, BlockAdd); + } + else + { + hmmc->Context = (MMC_CONTEXT_READ_SINGLE_BLOCK | MMC_CONTEXT_DMA); + + /* Read Single Block command */ + errorstate = SDMMC_CmdReadSingleBlock(hmmc->Instance, BlockAdd); + } + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Writes block(s) to a specified address in a card. The Data transfer + * is managed by DMA mode. + * @note This API should be followed by a check on the card state through + * HAL_MMC_GetCardState(). + * @note You could also check the DMA transfer process through the MMC Tx + * interrupt event. + * @param hmmc Pointer to MMC handle + * @param pData Pointer to the buffer that will contain the data to transmit + * @param BlockAdd Block Address where data will be written + * @param NumberOfBlocks Number of blocks to write + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_WriteBlocks_DMA(MMC_HandleTypeDef *hmmc, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks) +{ + SDIO_DataInitTypeDef config; + uint32_t errorstate = HAL_MMC_ERROR_NONE; + + if(NULL == pData) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_PARAM; + return HAL_ERROR; + } + + if(hmmc->State == HAL_MMC_STATE_READY) + { + hmmc->ErrorCode = HAL_DMA_ERROR_NONE; + + if((BlockAdd + NumberOfBlocks) > (hmmc->MmcCard.LogBlockNbr)) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_ADDR_OUT_OF_RANGE; + return HAL_ERROR; + } + + hmmc->State = HAL_MMC_STATE_BUSY; + + /* Initialize data control register */ + hmmc->Instance->DCTRL = 0U; + + /* Enable MMC Error interrupts */ +#ifdef SDIO_STA_STBITER + __HAL_MMC_ENABLE_IT(hmmc, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_TXUNDERR | SDIO_IT_STBITERR)); +#else /* SDIO_STA_STBITERR not defined */ + __HAL_MMC_ENABLE_IT(hmmc, (SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_TXUNDERR)); +#endif /* SDIO_STA_STBITERR */ + + /* Set the DMA transfer complete callback */ + hmmc->hdmatx->XferCpltCallback = MMC_DMATransmitCplt; + + /* Set the DMA error callback */ + hmmc->hdmatx->XferErrorCallback = MMC_DMAError; + + /* Set the DMA Abort callback */ + hmmc->hdmatx->XferAbortCallback = NULL; + + /* Check the Card capacity in term of Logical number of blocks */ + if ((hmmc->MmcCard.LogBlockNbr) < CAPACITY) + { + BlockAdd *= 512U; + } + + /* Set Block Size for Card */ + errorstate = SDMMC_CmdBlockLength(hmmc->Instance, BLOCKSIZE); + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Write Blocks in Polling mode */ + if(NumberOfBlocks > 1U) + { + hmmc->Context = (MMC_CONTEXT_WRITE_MULTIPLE_BLOCK | MMC_CONTEXT_DMA); + + /* Write Multi Block command */ + errorstate = SDMMC_CmdWriteMultiBlock(hmmc->Instance, BlockAdd); + } + else + { + hmmc->Context = (MMC_CONTEXT_WRITE_SINGLE_BLOCK | MMC_CONTEXT_DMA); + + /* Write Single Block command */ + errorstate = SDMMC_CmdWriteSingleBlock(hmmc->Instance, BlockAdd); + } + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Enable SDIO DMA transfer */ + __HAL_MMC_DMA_ENABLE(hmmc); + + /* Enable the DMA Channel */ + HAL_DMA_Start_IT(hmmc->hdmatx, (uint32_t)pData, (uint32_t)&hmmc->Instance->FIFO, (uint32_t)(BLOCKSIZE * NumberOfBlocks)/4); + + /* Configure the MMC DPSM (Data Path State Machine) */ + config.DataTimeOut = SDMMC_DATATIMEOUT; + config.DataLength = BLOCKSIZE * NumberOfBlocks; + config.DataBlockSize = SDIO_DATABLOCK_SIZE_512B; + config.TransferDir = SDIO_TRANSFER_DIR_TO_CARD; + config.TransferMode = SDIO_TRANSFER_MODE_BLOCK; + config.DPSM = SDIO_DPSM_ENABLE; + SDIO_ConfigData(hmmc->Instance, &config); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Erases the specified memory area of the given MMC card. + * @note This API should be followed by a check on the card state through + * HAL_MMC_GetCardState(). + * @param hmmc Pointer to MMC handle + * @param BlockStartAdd Start Block address + * @param BlockEndAdd End Block address + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_Erase(MMC_HandleTypeDef *hmmc, uint32_t BlockStartAdd, uint32_t BlockEndAdd) +{ + uint32_t errorstate = HAL_MMC_ERROR_NONE; + + if(hmmc->State == HAL_MMC_STATE_READY) + { + hmmc->ErrorCode = HAL_DMA_ERROR_NONE; + + if(BlockEndAdd < BlockStartAdd) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_PARAM; + return HAL_ERROR; + } + + if(BlockEndAdd > (hmmc->MmcCard.LogBlockNbr)) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_ADDR_OUT_OF_RANGE; + return HAL_ERROR; + } + + hmmc->State = HAL_MMC_STATE_BUSY; + + /* Check if the card command class supports erase command */ + if(((hmmc->MmcCard.Class) & SDIO_CCCC_ERASE) == 0U) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->ErrorCode |= HAL_MMC_ERROR_REQUEST_NOT_APPLICABLE; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + if((SDIO_GetResponse(hmmc->Instance, SDIO_RESP1) & SDMMC_CARD_LOCKED) == SDMMC_CARD_LOCKED) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDMMC_STATIC_FLAGS); + hmmc->ErrorCode |= HAL_MMC_ERROR_LOCK_UNLOCK_FAILED; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Check the Card capacity in term of Logical number of blocks */ + if ((hmmc->MmcCard.LogBlockNbr) < CAPACITY) + { + BlockStartAdd *= 512U; + BlockEndAdd *= 512U; + } + + /* Send CMD35 MMC_ERASE_GRP_START with argument as addr */ + errorstate = SDMMC_CmdEraseStartAdd(hmmc->Instance, BlockStartAdd); + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDMMC_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Send CMD36 MMC_ERASE_GRP_END with argument as addr */ + errorstate = SDMMC_CmdEraseEndAdd(hmmc->Instance, BlockEndAdd); + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDMMC_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + /* Send CMD38 ERASE */ + errorstate = SDMMC_CmdErase(hmmc->Instance); + if(errorstate != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDMMC_STATIC_FLAGS); + hmmc->ErrorCode |= errorstate; + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + + hmmc->State = HAL_MMC_STATE_READY; + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief This function handles MMC card interrupt request. + * @param hmmc Pointer to MMC handle + * @retval None + */ +void HAL_MMC_IRQHandler(MMC_HandleTypeDef *hmmc) +{ + uint32_t errorstate = HAL_MMC_ERROR_NONE; + + /* Check for SDIO interrupt flags */ + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_DATAEND) != RESET) + { + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_FLAG_DATAEND); + +#ifdef SDIO_STA_STBITERR + __HAL_MMC_DISABLE_IT(hmmc, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ + SDIO_IT_TXUNDERR | SDIO_IT_RXOVERR | SDIO_IT_STBITERR); +#else /* SDIO_STA_STBITERR not defined */ + __HAL_MMC_DISABLE_IT(hmmc, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ + SDIO_IT_TXUNDERR | SDIO_IT_RXOVERR); +#endif + + if((hmmc->Context & MMC_CONTEXT_IT) != RESET) + { + if(((hmmc->Context & MMC_CONTEXT_READ_MULTIPLE_BLOCK) != RESET) || ((hmmc->Context & MMC_CONTEXT_WRITE_MULTIPLE_BLOCK) != RESET)) + { + errorstate = SDMMC_CmdStopTransfer(hmmc->Instance); + if(errorstate != HAL_MMC_ERROR_NONE) + { + hmmc->ErrorCode |= errorstate; + HAL_MMC_ErrorCallback(hmmc); + } + } + + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + + hmmc->State = HAL_MMC_STATE_READY; + if(((hmmc->Context & MMC_CONTEXT_READ_SINGLE_BLOCK) != RESET) || ((hmmc->Context & MMC_CONTEXT_READ_MULTIPLE_BLOCK) != RESET)) + { + HAL_MMC_RxCpltCallback(hmmc); + } + else + { + HAL_MMC_TxCpltCallback(hmmc); + } + } + else if((hmmc->Context & MMC_CONTEXT_DMA) != RESET) + { + if((hmmc->Context & MMC_CONTEXT_WRITE_MULTIPLE_BLOCK) != RESET) + { + errorstate = SDMMC_CmdStopTransfer(hmmc->Instance); + if(errorstate != HAL_MMC_ERROR_NONE) + { + hmmc->ErrorCode |= errorstate; + HAL_MMC_ErrorCallback(hmmc); + } + } + if(((hmmc->Context & MMC_CONTEXT_READ_SINGLE_BLOCK) == RESET) && ((hmmc->Context & MMC_CONTEXT_READ_MULTIPLE_BLOCK) == RESET)) + { + /* Disable the DMA transfer for transmit request by setting the DMAEN bit + in the MMC DCTRL register */ + hmmc->Instance->DCTRL &= (uint32_t)~((uint32_t)SDIO_DCTRL_DMAEN); + + hmmc->State = HAL_MMC_STATE_READY; + + HAL_MMC_TxCpltCallback(hmmc); + } + } + } + + else if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_TXFIFOHE) != RESET) + { + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_FLAG_TXFIFOHE); + + MMC_Write_IT(hmmc); + } + + else if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_RXFIFOHF) != RESET) + { + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_FLAG_RXFIFOHF); + + MMC_Read_IT(hmmc); + } + +#ifdef SDIO_STA_STBITERR + else if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_RXOVERR | SDIO_IT_TXUNDERR | SDIO_IT_STBITERR) != RESET) + { + /* Set Error code */ + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_DCRCFAIL) != RESET) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_DATA_CRC_FAIL; + } + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_DTIMEOUT) != RESET) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_DATA_TIMEOUT; + } + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_RXOVERR) != RESET) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_RX_OVERRUN; + } + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_TXUNDERR) != RESET) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_TX_UNDERRUN; + } + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_STBITERR) != RESET) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_DATA_TIMEOUT; + } + + /* Clear All flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS | SDIO_FLAG_STBITERR); + + /* Disable all interrupts */ + __HAL_MMC_DISABLE_IT(hmmc, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ + SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR |SDIO_IT_STBITERR); + + if((hmmc->Context & MMC_CONTEXT_DMA) != RESET) + { + /* Abort the MMC DMA Streams */ + if(hmmc->hdmatx != NULL) + { + /* Set the DMA Tx abort callback */ + hmmc->hdmatx->XferAbortCallback = MMC_DMATxAbort; + /* Abort DMA in IT mode */ + if(HAL_DMA_Abort_IT(hmmc->hdmatx) != HAL_OK) + { + MMC_DMATxAbort(hmmc->hdmatx); + } + } + else if(hmmc->hdmarx != NULL) + { + /* Set the DMA Rx abort callback */ + hmmc->hdmarx->XferAbortCallback = MMC_DMARxAbort; + /* Abort DMA in IT mode */ + if(HAL_DMA_Abort_IT(hmmc->hdmarx) != HAL_OK) + { + MMC_DMARxAbort(hmmc->hdmarx); + } + } + else + { + hmmc->ErrorCode = HAL_MMC_ERROR_NONE; + hmmc->State = HAL_MMC_STATE_READY; + HAL_MMC_AbortCallback(hmmc); + } + } + else if((hmmc->Context & MMC_CONTEXT_IT) != RESET) + { + /* Set the MMC state to ready to be able to start again the process */ + hmmc->State = HAL_MMC_STATE_READY; + HAL_MMC_ErrorCallback(hmmc); + } + } +#else /* SDIO_STA_STBITERR not defined */ + else if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT | SDIO_IT_RXOVERR | SDIO_IT_TXUNDERR) != RESET) + { + /* Set Error code */ + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_DCRCFAIL) != RESET) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_DATA_CRC_FAIL; + } + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_DTIMEOUT) != RESET) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_DATA_TIMEOUT; + } + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_RXOVERR) != RESET) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_RX_OVERRUN; + } + if(__HAL_MMC_GET_FLAG(hmmc, SDIO_IT_TXUNDERR) != RESET) + { + hmmc->ErrorCode |= HAL_MMC_ERROR_TX_UNDERRUN; + } + + /* Clear All flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + + /* Disable all interrupts */ + __HAL_MMC_DISABLE_IT(hmmc, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ + SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR); + + if((hmmc->Context & MMC_CONTEXT_DMA) != RESET) + { + /* Abort the MMC DMA Streams */ + if(hmmc->hdmatx != NULL) + { + /* Set the DMA Tx abort callback */ + hmmc->hdmatx->XferAbortCallback = MMC_DMATxAbort; + /* Abort DMA in IT mode */ + if(HAL_DMA_Abort_IT(hmmc->hdmatx) != HAL_OK) + { + MMC_DMATxAbort(hmmc->hdmatx); + } + } + else if(hmmc->hdmarx != NULL) + { + /* Set the DMA Rx abort callback */ + hmmc->hdmarx->XferAbortCallback = MMC_DMARxAbort; + /* Abort DMA in IT mode */ + if(HAL_DMA_Abort_IT(hmmc->hdmarx) != HAL_OK) + { + MMC_DMARxAbort(hmmc->hdmarx); + } + } + else + { + hmmc->ErrorCode = HAL_MMC_ERROR_NONE; + hmmc->State = HAL_MMC_STATE_READY; + HAL_MMC_AbortCallback(hmmc); + } + } + else if((hmmc->Context & MMC_CONTEXT_IT) != RESET) + { + /* Set the MMC state to ready to be able to start again the process */ + hmmc->State = HAL_MMC_STATE_READY; + HAL_MMC_ErrorCallback(hmmc); + } + } +#endif /* SDIO_STA_STBITERR */ +} + +/** + * @brief return the MMC state + * @param hmmc Pointer to mmc handle + * @retval HAL state + */ +HAL_MMC_StateTypeDef HAL_MMC_GetState(MMC_HandleTypeDef *hmmc) +{ + return hmmc->State; +} + +/** +* @brief Return the MMC error code +* @param hmmc Pointer to a MMC_HandleTypeDef structure that contains + * the configuration information. +* @retval MMC Error Code +*/ +uint32_t HAL_MMC_GetError(MMC_HandleTypeDef *hmmc) +{ + return hmmc->ErrorCode; +} + +/** + * @brief Tx Transfer completed callbacks + * @param hmmc Pointer to MMC handle + * @retval None + */ + __weak void HAL_MMC_TxCpltCallback(MMC_HandleTypeDef *hmmc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hmmc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_MMC_TxCpltCallback can be implemented in the user file + */ +} + +/** + * @brief Rx Transfer completed callbacks + * @param hmmc Pointer MMC handle + * @retval None + */ +__weak void HAL_MMC_RxCpltCallback(MMC_HandleTypeDef *hmmc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hmmc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_MMC_RxCpltCallback can be implemented in the user file + */ +} + +/** + * @brief MMC error callbacks + * @param hmmc Pointer MMC handle + * @retval None + */ +__weak void HAL_MMC_ErrorCallback(MMC_HandleTypeDef *hmmc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hmmc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_MMC_ErrorCallback can be implemented in the user file + */ +} + +/** + * @brief MMC Abort callbacks + * @param hmmc Pointer MMC handle + * @retval None + */ +__weak void HAL_MMC_AbortCallback(MMC_HandleTypeDef *hmmc) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(hmmc); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_MMC_ErrorCallback can be implemented in the user file + */ +} + + +/** + * @} + */ + +/** @addtogroup MMC_Exported_Functions_Group3 + * @brief management functions + * +@verbatim + ============================================================================== + ##### Peripheral Control functions ##### + ============================================================================== + [..] + This subsection provides a set of functions allowing to control the MMC card + operations and get the related information + +@endverbatim + * @{ + */ + +/** + * @brief Returns information the information of the card which are stored on + * the CID register. + * @param hmmc Pointer to MMC handle + * @param pCID Pointer to a HAL_MMC_CIDTypedef structure that + * contains all CID register parameters + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_GetCardCID(MMC_HandleTypeDef *hmmc, HAL_MMC_CardCIDTypeDef *pCID) +{ + uint32_t tmp = 0U; + + /* Byte 0 */ + tmp = (uint8_t)((hmmc->CID[0U] & 0xFF000000U) >> 24U); + pCID->ManufacturerID = tmp; + + /* Byte 1 */ + tmp = (uint8_t)((hmmc->CID[0U] & 0x00FF0000U) >> 16U); + pCID->OEM_AppliID = tmp << 8U; + + /* Byte 2 */ + tmp = (uint8_t)((hmmc->CID[0U] & 0x000000FF00U) >> 8U); + pCID->OEM_AppliID |= tmp; + + /* Byte 3 */ + tmp = (uint8_t)(hmmc->CID[0U] & 0x000000FFU); + pCID->ProdName1 = tmp << 24U; + + /* Byte 4 */ + tmp = (uint8_t)((hmmc->CID[1U] & 0xFF000000U) >> 24U); + pCID->ProdName1 |= tmp << 16U; + + /* Byte 5 */ + tmp = (uint8_t)((hmmc->CID[1U] & 0x00FF0000U) >> 16U); + pCID->ProdName1 |= tmp << 8U; + + /* Byte 6 */ + tmp = (uint8_t)((hmmc->CID[1U] & 0x0000FF00U) >> 8U); + pCID->ProdName1 |= tmp; + + /* Byte 7 */ + tmp = (uint8_t)(hmmc->CID[1U] & 0x000000FFU); + pCID->ProdName2 = tmp; + + /* Byte 8 */ + tmp = (uint8_t)((hmmc->CID[2U] & 0xFF000000U) >> 24U); + pCID->ProdRev = tmp; + + /* Byte 9 */ + tmp = (uint8_t)((hmmc->CID[2U] & 0x00FF0000U) >> 16U); + pCID->ProdSN = tmp << 24U; + + /* Byte 10 */ + tmp = (uint8_t)((hmmc->CID[2U] & 0x0000FF00U) >> 8U); + pCID->ProdSN |= tmp << 16U; + + /* Byte 11 */ + tmp = (uint8_t)(hmmc->CID[2U] & 0x000000FFU); + pCID->ProdSN |= tmp << 8U; + + /* Byte 12 */ + tmp = (uint8_t)((hmmc->CID[3U] & 0xFF000000U) >> 24U); + pCID->ProdSN |= tmp; + + /* Byte 13 */ + tmp = (uint8_t)((hmmc->CID[3U] & 0x00FF0000U) >> 16U); + pCID->Reserved1 |= (tmp & 0xF0U) >> 4U; + pCID->ManufactDate = (tmp & 0x0FU) << 8U; + + /* Byte 14 */ + tmp = (uint8_t)((hmmc->CID[3U] & 0x0000FF00U) >> 8U); + pCID->ManufactDate |= tmp; + + /* Byte 15 */ + tmp = (uint8_t)(hmmc->CID[3U] & 0x000000FFU); + pCID->CID_CRC = (tmp & 0xFEU) >> 1U; + pCID->Reserved2 = 1U; + + return HAL_OK; +} + +/** + * @brief Returns information the information of the card which are stored on + * the CSD register. + * @param hmmc Pointer to MMC handle + * @param pCSD Pointer to a HAL_MMC_CardInfoTypeDef structure that + * contains all CSD register parameters + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_GetCardCSD(MMC_HandleTypeDef *hmmc, HAL_MMC_CardCSDTypeDef *pCSD) +{ + uint32_t tmp = 0U; + + /* Byte 0 */ + tmp = (hmmc->CSD[0U] & 0xFF000000U) >> 24U; + pCSD->CSDStruct = (uint8_t)((tmp & 0xC0U) >> 6U); + pCSD->SysSpecVersion = (uint8_t)((tmp & 0x3CU) >> 2U); + pCSD->Reserved1 = tmp & 0x03U; + + /* Byte 1 */ + tmp = (hmmc->CSD[0U] & 0x00FF0000U) >> 16U; + pCSD->TAAC = (uint8_t)tmp; + + /* Byte 2 */ + tmp = (hmmc->CSD[0U] & 0x0000FF00U) >> 8U; + pCSD->NSAC = (uint8_t)tmp; + + /* Byte 3 */ + tmp = hmmc->CSD[0U] & 0x000000FFU; + pCSD->MaxBusClkFrec = (uint8_t)tmp; + + /* Byte 4 */ + tmp = (hmmc->CSD[1U] & 0xFF000000U) >> 24U; + pCSD->CardComdClasses = (uint16_t)(tmp << 4U); + + /* Byte 5 */ + tmp = (hmmc->CSD[1U] & 0x00FF0000U) >> 16U; + pCSD->CardComdClasses |= (uint16_t)((tmp & 0xF0U) >> 4U); + pCSD->RdBlockLen = (uint8_t)(tmp & 0x0FU); + + /* Byte 6 */ + tmp = (hmmc->CSD[1U] & 0x0000FF00U) >> 8U; + pCSD->PartBlockRead = (uint8_t)((tmp & 0x80U) >> 7U); + pCSD->WrBlockMisalign = (uint8_t)((tmp & 0x40U) >> 6U); + pCSD->RdBlockMisalign = (uint8_t)((tmp & 0x20U) >> 5U); + pCSD->DSRImpl = (uint8_t)((tmp & 0x10U) >> 4U); + pCSD->Reserved2 = 0; /*!< Reserved */ + + pCSD->DeviceSize = (tmp & 0x03U) << 10U; + + /* Byte 7 */ + tmp = (uint8_t)(hmmc->CSD[1U] & 0x000000FFU); + pCSD->DeviceSize |= (tmp) << 2U; + + /* Byte 8 */ + tmp = (uint8_t)((hmmc->CSD[2U] & 0xFF000000U) >> 24U); + pCSD->DeviceSize |= (tmp & 0xC0U) >> 6U; + + pCSD->MaxRdCurrentVDDMin = (tmp & 0x38U) >> 3U; + pCSD->MaxRdCurrentVDDMax = (tmp & 0x07U); + + /* Byte 9 */ + tmp = (uint8_t)((hmmc->CSD[2U] & 0x00FF0000U) >> 16U); + pCSD->MaxWrCurrentVDDMin = (tmp & 0xE0U) >> 5U; + pCSD->MaxWrCurrentVDDMax = (tmp & 0x1CU) >> 2U; + pCSD->DeviceSizeMul = (tmp & 0x03U) << 1U; + /* Byte 10 */ + tmp = (uint8_t)((hmmc->CSD[2] & 0x0000FF00U) >> 8U); + pCSD->DeviceSizeMul |= (tmp & 0x80U) >> 7U; + + hmmc->MmcCard.BlockNbr = (pCSD->DeviceSize + 1U) ; + hmmc->MmcCard.BlockNbr *= (1U << (pCSD->DeviceSizeMul + 2U)); + hmmc->MmcCard.BlockSize = 1U << (pCSD->RdBlockLen); + + hmmc->MmcCard.LogBlockNbr = (hmmc->MmcCard.BlockNbr) * ((hmmc->MmcCard.BlockSize) / 512U); + hmmc->MmcCard.LogBlockSize = 512U; + + pCSD->EraseGrSize = (tmp & 0x40U) >> 6U; + pCSD->EraseGrMul = (tmp & 0x3FU) << 1U; + + /* Byte 11 */ + tmp = (uint8_t)(hmmc->CSD[2U] & 0x000000FFU); + pCSD->EraseGrMul |= (tmp & 0x80U) >> 7U; + pCSD->WrProtectGrSize = (tmp & 0x7FU); + + /* Byte 12 */ + tmp = (uint8_t)((hmmc->CSD[3U] & 0xFF000000U) >> 24U); + pCSD->WrProtectGrEnable = (tmp & 0x80U) >> 7U; + pCSD->ManDeflECC = (tmp & 0x60U) >> 5U; + pCSD->WrSpeedFact = (tmp & 0x1CU) >> 2U; + pCSD->MaxWrBlockLen = (tmp & 0x03U) << 2U; + + /* Byte 13 */ + tmp = (uint8_t)((hmmc->CSD[3U] & 0x00FF0000U) >> 16U); + pCSD->MaxWrBlockLen |= (tmp & 0xC0U) >> 6U; + pCSD->WriteBlockPaPartial = (tmp & 0x20U) >> 5U; + pCSD->Reserved3 = 0U; + pCSD->ContentProtectAppli = (tmp & 0x01U); + + /* Byte 14 */ + tmp = (uint8_t)((hmmc->CSD[3U] & 0x0000FF00U) >> 8U); + pCSD->FileFormatGrouop = (tmp & 0x80U) >> 7U; + pCSD->CopyFlag = (tmp & 0x40U) >> 6U; + pCSD->PermWrProtect = (tmp & 0x20U) >> 5U; + pCSD->TempWrProtect = (tmp & 0x10U) >> 4U; + pCSD->FileFormat = (tmp & 0x0CU) >> 2U; + pCSD->ECC = (tmp & 0x03U); + + /* Byte 15 */ + tmp = (uint8_t)(hmmc->CSD[3U] & 0x000000FFU); + pCSD->CSD_CRC = (tmp & 0xFEU) >> 1U; + pCSD->Reserved4 = 1U; + + return HAL_OK; +} + +/** + * @brief Gets the MMC card info. + * @param hmmc Pointer to MMC handle + * @param pCardInfo Pointer to the HAL_MMC_CardInfoTypeDef structure that + * will contain the MMC card status information + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_GetCardInfo(MMC_HandleTypeDef *hmmc, HAL_MMC_CardInfoTypeDef *pCardInfo) +{ + pCardInfo->CardType = (uint32_t)(hmmc->MmcCard.CardType); + pCardInfo->Class = (uint32_t)(hmmc->MmcCard.Class); + pCardInfo->RelCardAdd = (uint32_t)(hmmc->MmcCard.RelCardAdd); + pCardInfo->BlockNbr = (uint32_t)(hmmc->MmcCard.BlockNbr); + pCardInfo->BlockSize = (uint32_t)(hmmc->MmcCard.BlockSize); + pCardInfo->LogBlockNbr = (uint32_t)(hmmc->MmcCard.LogBlockNbr); + pCardInfo->LogBlockSize = (uint32_t)(hmmc->MmcCard.LogBlockSize); + + return HAL_OK; +} + +/** + * @brief Enables wide bus operation for the requested card if supported by + * card. + * @param hmmc Pointer to MMC handle + * @param WideMode Specifies the MMC card wide bus mode + * This parameter can be one of the following values: + * @arg SDIO_BUS_WIDE_8B: 8-bit data transfer + * @arg SDIO_BUS_WIDE_4B: 4-bit data transfer + * @arg SDIO_BUS_WIDE_1B: 1-bit data transfer + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_ConfigWideBusOperation(MMC_HandleTypeDef *hmmc, uint32_t WideMode) +{ + __IO uint32_t count = 0U; + SDIO_InitTypeDef Init; + uint32_t errorstate = HAL_MMC_ERROR_NONE; + uint32_t response = 0U, busy = 0U; + + /* Check the parameters */ + assert_param(IS_SDIO_BUS_WIDE(WideMode)); + + /* Chnage Satte */ + hmmc->State = HAL_MMC_STATE_BUSY; + + /* Update Clock for Bus mode update */ + Init.ClockEdge = SDIO_CLOCK_EDGE_RISING; + Init.ClockBypass = SDIO_CLOCK_BYPASS_DISABLE; + Init.ClockPowerSave = SDIO_CLOCK_POWER_SAVE_DISABLE; + Init.BusWide = WideMode; + Init.HardwareFlowControl = SDIO_HARDWARE_FLOW_CONTROL_DISABLE; + Init.ClockDiv = SDIO_INIT_CLK_DIV; + /* Initialize SDIO*/ + SDIO_Init(hmmc->Instance, Init); + + if(WideMode == SDIO_BUS_WIDE_8B) + { + errorstate = SDMMC_CmdSwitch(hmmc->Instance, 0x03B70200U); + if(errorstate != HAL_MMC_ERROR_NONE) + { + hmmc->ErrorCode |= errorstate; + } + } + else if(WideMode == SDIO_BUS_WIDE_4B) + { + errorstate = SDMMC_CmdSwitch(hmmc->Instance, 0x03B70100U); + if(errorstate != HAL_MMC_ERROR_NONE) + { + hmmc->ErrorCode |= errorstate; + } + } + else if(WideMode == SDIO_BUS_WIDE_1B) + { + errorstate = SDMMC_CmdSwitch(hmmc->Instance, 0x03B70000U); + if(errorstate != HAL_MMC_ERROR_NONE) + { + hmmc->ErrorCode |= errorstate; + } + } + else + { + /* WideMode is not a valid argument*/ + hmmc->ErrorCode |= HAL_MMC_ERROR_PARAM; + } + + /* Check for switch error and violation of the trial number of sending CMD 13 */ + while(busy == 0U) + { + if(count++ == SDMMC_MAX_TRIAL) + { + hmmc->State = HAL_MMC_STATE_READY; + hmmc->ErrorCode |= HAL_MMC_ERROR_REQUEST_NOT_APPLICABLE; + return HAL_ERROR; + } + + /* While card is not ready for data and trial number for sending CMD13 is not exceeded */ + errorstate = SDMMC_CmdSendStatus(hmmc->Instance, (uint32_t)(((uint32_t)hmmc->MmcCard.RelCardAdd) << 16U)); + if(errorstate != HAL_MMC_ERROR_NONE) + { + hmmc->ErrorCode |= errorstate; + } + + /* Get command response */ + response = SDIO_GetResponse(hmmc->Instance, SDIO_RESP1); + + /* Get operating voltage*/ + busy = (((response >> 7U) == 1U) ? 0U : 1U); + } + + /* While card is not ready for data and trial number for sending CMD13 is not exceeded */ + count = SDMMC_DATATIMEOUT; + while((response & 0x00000100U) == 0U) + { + if(count-- == 0U) + { + hmmc->State = HAL_MMC_STATE_READY; + hmmc->ErrorCode |= HAL_MMC_ERROR_REQUEST_NOT_APPLICABLE; + return HAL_ERROR; + } + + /* While card is not ready for data and trial number for sending CMD13 is not exceeded */ + errorstate = SDMMC_CmdSendStatus(hmmc->Instance, (uint32_t)(((uint32_t)hmmc->MmcCard.RelCardAdd) << 16U)); + if(errorstate != HAL_MMC_ERROR_NONE) + { + hmmc->ErrorCode |= errorstate; + } + + /* Get command response */ + response = SDIO_GetResponse(hmmc->Instance, SDIO_RESP1); + } + + if(hmmc->ErrorCode != HAL_MMC_ERROR_NONE) + { + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + hmmc->State = HAL_MMC_STATE_READY; + return HAL_ERROR; + } + else + { + /* Configure the SDIO peripheral */ + Init.ClockEdge = hmmc->Init.ClockEdge; + Init.ClockBypass = hmmc->Init.ClockBypass; + Init.ClockPowerSave = hmmc->Init.ClockPowerSave; + Init.BusWide = WideMode; + Init.HardwareFlowControl = hmmc->Init.HardwareFlowControl; + Init.ClockDiv = hmmc->Init.ClockDiv; + SDIO_Init(hmmc->Instance, Init); + } + + /* Change State */ + hmmc->State = HAL_MMC_STATE_READY; + + return HAL_OK; +} + + +/** + * @brief Gets the current mmc card data state. + * @param hmmc pointer to MMC handle + * @retval Card state + */ +HAL_MMC_CardStateTypeDef HAL_MMC_GetCardState(MMC_HandleTypeDef *hmmc) +{ + HAL_MMC_CardStateTypeDef cardstate = HAL_MMC_CARD_TRANSFER; + uint32_t errorstate = HAL_MMC_ERROR_NONE; + uint32_t resp1 = 0U; + + errorstate = MMC_SendStatus(hmmc, &resp1); + if(errorstate != HAL_OK) + { + hmmc->ErrorCode |= errorstate; + } + + cardstate = (HAL_MMC_CardStateTypeDef)((resp1 >> 9U) & 0x0FU); + + return cardstate; +} + +/** + * @brief Abort the current transfer and disable the MMC. + * @param hmmc pointer to a MMC_HandleTypeDef structure that contains + * the configuration information for MMC module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_Abort(MMC_HandleTypeDef *hmmc) +{ + HAL_MMC_CardStateTypeDef CardState; + + /* DIsable All interrupts */ + __HAL_MMC_DISABLE_IT(hmmc, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ + SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR); + + /* Clear All flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + + if((hmmc->hdmatx != NULL) || (hmmc->hdmarx != NULL)) + { + /* Disable the MMC DMA request */ + hmmc->Instance->DCTRL &= (uint32_t)~((uint32_t)SDIO_DCTRL_DMAEN); + + /* Abort the MMC DMA Tx Stream */ + if(hmmc->hdmatx != NULL) + { + HAL_DMA_Abort(hmmc->hdmatx); + } + /* Abort the MMC DMA Rx Stream */ + if(hmmc->hdmarx != NULL) + { + HAL_DMA_Abort(hmmc->hdmarx); + } + } + + hmmc->State = HAL_MMC_STATE_READY; + CardState = HAL_MMC_GetCardState(hmmc); + if((CardState == HAL_MMC_CARD_RECEIVING) || (CardState == HAL_MMC_CARD_SENDING)) + { + hmmc->ErrorCode = SDMMC_CmdStopTransfer(hmmc->Instance); + } + if(hmmc->ErrorCode != HAL_MMC_ERROR_NONE) + { + return HAL_ERROR; + } + return HAL_OK; +} + +/** + * @brief Abort the current transfer and disable the MMC (IT mode). + * @param hmmc pointer to a MMC_HandleTypeDef structure that contains + * the configuration information for MMC module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MMC_Abort_IT(MMC_HandleTypeDef *hmmc) +{ + HAL_MMC_CardStateTypeDef CardState; + + /* DIsable All interrupts */ + __HAL_MMC_DISABLE_IT(hmmc, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ + SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR); + + /* Clear All flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + + if((hmmc->hdmatx != NULL) || (hmmc->hdmarx != NULL)) + { + /* Disable the MMC DMA request */ + hmmc->Instance->DCTRL &= (uint32_t)~((uint32_t)SDIO_DCTRL_DMAEN); + + /* Abort the MMC DMA Tx Stream */ + if(hmmc->hdmatx != NULL) + { + hmmc->hdmatx->XferAbortCallback = MMC_DMATxAbort; + if(HAL_DMA_Abort_IT(hmmc->hdmatx) != HAL_OK) + { + hmmc->hdmatx = NULL; + } + } + /* Abort the MMC DMA Rx Stream */ + if(hmmc->hdmarx != NULL) + { + hmmc->hdmarx->XferAbortCallback = MMC_DMARxAbort; + if(HAL_DMA_Abort_IT(hmmc->hdmarx) != HAL_OK) + { + hmmc->hdmarx = NULL; + } + } + } + + /* No transfer ongoing on both DMA channels*/ + if((hmmc->hdmatx == NULL) && (hmmc->hdmarx == NULL)) + { + CardState = HAL_MMC_GetCardState(hmmc); + hmmc->State = HAL_MMC_STATE_READY; + if((CardState == HAL_MMC_CARD_RECEIVING) || (CardState == HAL_MMC_CARD_SENDING)) + { + hmmc->ErrorCode = SDMMC_CmdStopTransfer(hmmc->Instance); + } + if(hmmc->ErrorCode != HAL_MMC_ERROR_NONE) + { + return HAL_ERROR; + } + else + { + HAL_MMC_AbortCallback(hmmc); + } + } + + return HAL_OK; +} + +/** + * @} + */ + +/** + * @} + */ + +/* Private function ----------------------------------------------------------*/ +/** @addtogroup MMC_Private_Functions + * @{ + */ + +/** + * @brief DMA MMC transmit process complete callback + * @param hdma DMA handle + * @retval None + */ +static void MMC_DMATransmitCplt(DMA_HandleTypeDef *hdma) +{ + MMC_HandleTypeDef* hmmc = (MMC_HandleTypeDef* )(hdma->Parent); + + /* Enable DATAEND Interrupt */ + __HAL_MMC_ENABLE_IT(hmmc, (SDIO_IT_DATAEND)); +} + +/** + * @brief DMA MMC receive process complete callback + * @param hdma DMA handle + * @retval None + */ +static void MMC_DMAReceiveCplt(DMA_HandleTypeDef *hdma) +{ + MMC_HandleTypeDef* hmmc = (MMC_HandleTypeDef* )(hdma->Parent); + uint32_t errorstate = HAL_MMC_ERROR_NONE; + + /* Send stop command in multiblock write */ + if(hmmc->Context == (MMC_CONTEXT_READ_MULTIPLE_BLOCK | MMC_CONTEXT_DMA)) + { + errorstate = SDMMC_CmdStopTransfer(hmmc->Instance); + if(errorstate != HAL_MMC_ERROR_NONE) + { + hmmc->ErrorCode |= errorstate; + HAL_MMC_ErrorCallback(hmmc); + } + } + + /* Disable the DMA transfer for transmit request by setting the DMAEN bit + in the MMC DCTRL register */ + hmmc->Instance->DCTRL &= (uint32_t)~((uint32_t)SDIO_DCTRL_DMAEN); + + /* Clear all the static flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + + hmmc->State = HAL_MMC_STATE_READY; + + HAL_MMC_RxCpltCallback(hmmc); +} + +/** + * @brief DMA MMC communication error callback + * @param hdma DMA handle + * @retval None + */ +static void MMC_DMAError(DMA_HandleTypeDef *hdma) +{ + MMC_HandleTypeDef* hmmc = (MMC_HandleTypeDef* )(hdma->Parent); + HAL_MMC_CardStateTypeDef CardState; + + if((hmmc->hdmarx->ErrorCode == HAL_DMA_ERROR_TE) || (hmmc->hdmatx->ErrorCode == HAL_DMA_ERROR_TE)) + { + /* Clear All flags */ + __HAL_MMC_CLEAR_FLAG(hmmc, SDIO_STATIC_FLAGS); + + /* Disable All interrupts */ + __HAL_MMC_DISABLE_IT(hmmc, SDIO_IT_DATAEND | SDIO_IT_DCRCFAIL | SDIO_IT_DTIMEOUT|\ + SDIO_IT_TXUNDERR| SDIO_IT_RXOVERR); + + hmmc->ErrorCode |= HAL_MMC_ERROR_DMA; + CardState = HAL_MMC_GetCardState(hmmc); + if((CardState == HAL_MMC_CARD_RECEIVING) || (CardState == HAL_MMC_CARD_SENDING)) + { + hmmc->ErrorCode |= SDMMC_CmdStopTransfer(hmmc->Instance); + } + + hmmc->State= HAL_MMC_STATE_READY; + } + + HAL_MMC_ErrorCallback(hmmc); +} + +/** + * @brief DMA MMC Tx Abort callback + * @param hdma DMA handle + * @retval None + */ +static void MMC_DMATxAbort(DMA_HandleTypeDef *hdma) +{ + MMC_HandleTypeDef* hmmc = (MMC_HandleTypeDef* )(hdma->Parent); + HAL_MMC_CardStateTypeDef CardState; + + if(hmmc->hdmatx != NULL) + { + hmmc->hdmatx = NULL; + } + + /* All DMA channels are aborted */ + if(hmmc->hdmarx == NULL) + { + CardState = HAL_MMC_GetCardState(hmmc); + hmmc->ErrorCode = HAL_MMC_ERROR_NONE; + hmmc->State = HAL_MMC_STATE_READY; + if((CardState == HAL_MMC_CARD_RECEIVING) || (CardState == HAL_MMC_CARD_SENDING)) + { + hmmc->ErrorCode |= SDMMC_CmdStopTransfer(hmmc->Instance); + + if(hmmc->ErrorCode != HAL_MMC_ERROR_NONE) + { + HAL_MMC_AbortCallback(hmmc); + } + else + { + HAL_MMC_ErrorCallback(hmmc); + } + } + } +} + +/** + * @brief DMA MMC Rx Abort callback + * @param hdma DMA handle + * @retval None + */ +static void MMC_DMARxAbort(DMA_HandleTypeDef *hdma) +{ + MMC_HandleTypeDef* hmmc = (MMC_HandleTypeDef* )(hdma->Parent); + HAL_MMC_CardStateTypeDef CardState; + + if(hmmc->hdmarx != NULL) + { + hmmc->hdmarx = NULL; + } + + /* All DMA channels are aborted */ + if(hmmc->hdmatx == NULL) + { + CardState = HAL_MMC_GetCardState(hmmc); + hmmc->ErrorCode = HAL_MMC_ERROR_NONE; + hmmc->State = HAL_MMC_STATE_READY; + if((CardState == HAL_MMC_CARD_RECEIVING) || (CardState == HAL_MMC_CARD_SENDING)) + { + hmmc->ErrorCode |= SDMMC_CmdStopTransfer(hmmc->Instance); + + if(hmmc->ErrorCode != HAL_MMC_ERROR_NONE) + { + HAL_MMC_AbortCallback(hmmc); + } + else + { + HAL_MMC_ErrorCallback(hmmc); + } + } + } +} + + +/** + * @brief Initializes the mmc card. + * @param hmmc Pointer to MMC handle + * @retval MMC Card error state + */ +static uint32_t MMC_InitCard(MMC_HandleTypeDef *hmmc) +{ + HAL_MMC_CardCSDTypeDef CSD; + uint32_t errorstate = HAL_MMC_ERROR_NONE; + uint16_t mmc_rca = 1; + + /* Check the power State */ + if(SDIO_GetPowerState(hmmc->Instance) == 0U) + { + /* Power off */ + return HAL_MMC_ERROR_REQUEST_NOT_APPLICABLE; + } + + /* Send CMD2 ALL_SEND_CID */ + errorstate = SDMMC_CmdSendCID(hmmc->Instance); + if(errorstate != HAL_MMC_ERROR_NONE) + { + return errorstate; + } + else + { + /* Get Card identification number data */ + hmmc->CID[0U] = SDIO_GetResponse(hmmc->Instance, SDIO_RESP1); + hmmc->CID[1U] = SDIO_GetResponse(hmmc->Instance, SDIO_RESP2); + hmmc->CID[2U] = SDIO_GetResponse(hmmc->Instance, SDIO_RESP3); + hmmc->CID[3U] = SDIO_GetResponse(hmmc->Instance, SDIO_RESP4); + } + + /* Send CMD3 SET_REL_ADDR with argument 0 */ + /* MMC Card publishes its RCA. */ + errorstate = SDMMC_CmdSetRelAdd(hmmc->Instance, &mmc_rca); + if(errorstate != HAL_MMC_ERROR_NONE) + { + return errorstate; + } + + /* Get the MMC card RCA */ + hmmc->MmcCard.RelCardAdd = mmc_rca; + + /* Send CMD9 SEND_CSD with argument as card's RCA */ + errorstate = SDMMC_CmdSendCSD(hmmc->Instance, (uint32_t)(hmmc->MmcCard.RelCardAdd << 16U)); + if(errorstate != HAL_MMC_ERROR_NONE) + { + return errorstate; + } + else + { + /* Get Card Specific Data */ + hmmc->CSD[0U] = SDIO_GetResponse(hmmc->Instance, SDIO_RESP1); + hmmc->CSD[1U] = SDIO_GetResponse(hmmc->Instance, SDIO_RESP2); + hmmc->CSD[2U] = SDIO_GetResponse(hmmc->Instance, SDIO_RESP3); + hmmc->CSD[3U] = SDIO_GetResponse(hmmc->Instance, SDIO_RESP4); + } + + /* Get the Card Class */ + hmmc->MmcCard.Class = (SDIO_GetResponse(hmmc->Instance, SDIO_RESP2) >> 20U); + + /* Get CSD parameters */ + HAL_MMC_GetCardCSD(hmmc, &CSD); + + /* Select the Card */ + errorstate = SDMMC_CmdSelDesel(hmmc->Instance, (uint32_t)(((uint32_t)hmmc->MmcCard.RelCardAdd) << 16U)); + if(errorstate != HAL_MMC_ERROR_NONE) + { + return errorstate; + } + + /* Configure SDIO peripheral interface */ + SDIO_Init(hmmc->Instance, hmmc->Init); + + /* All cards are initialized */ + return HAL_MMC_ERROR_NONE; +} + +/** + * @brief Enquires cards about their operating voltage and configures clock + * controls and stores MMC information that will be needed in future + * in the MMC handle. + * @param hmmc Pointer to MMC handle + * @retval error state + */ +static uint32_t MMC_PowerON(MMC_HandleTypeDef *hmmc) +{ + __IO uint32_t count = 0U; + uint32_t response = 0U, validvoltage = 0U; + uint32_t errorstate = HAL_MMC_ERROR_NONE; + + /* CMD0: GO_IDLE_STATE */ + errorstate = SDMMC_CmdGoIdleState(hmmc->Instance); + if(errorstate != HAL_MMC_ERROR_NONE) + { + return errorstate; + } + + while(validvoltage == 0U) + { + if(count++ == SDMMC_MAX_VOLT_TRIAL) + { + return HAL_MMC_ERROR_INVALID_VOLTRANGE; + } + + /* SEND CMD1 APP_CMD with MMC_HIGH_VOLTAGE_RANGE(0xC0FF8000) as argument */ + errorstate = SDMMC_CmdOpCondition(hmmc->Instance, eMMC_HIGH_VOLTAGE_RANGE); + if(errorstate != HAL_MMC_ERROR_NONE) + { + return HAL_MMC_ERROR_UNSUPPORTED_FEATURE; + } + + /* Get command response */ + response = SDIO_GetResponse(hmmc->Instance, SDIO_RESP1); + + /* Get operating voltage*/ + validvoltage = (((response >> 31U) == 1U) ? 1U : 0U); + } + + /* When power routine is finished and command returns valid voltage */ + if ((response & eMMC_HIGH_VOLTAGE_RANGE) == MMC_HIGH_VOLTAGE_RANGE) + { + /* When voltage range of the card is within 2.7V and 3.6V */ + hmmc->MmcCard.CardType = MMC_HIGH_VOLTAGE_CARD; + } + else + { + /* When voltage range of the card is within 1.65V and 1.95V or 2.7V and 3.6V */ + hmmc->MmcCard.CardType = MMC_DUAL_VOLTAGE_CARD; + } + + return HAL_MMC_ERROR_NONE; +} + +/** + * @brief Turns the SDIO output signals off. + * @param hmmc Pointer to MMC handle + * @retval HAL status + */ +static HAL_StatusTypeDef MMC_PowerOFF(MMC_HandleTypeDef *hmmc) +{ + /* Set Power State to OFF */ + SDIO_PowerState_OFF(hmmc->Instance); + + return HAL_OK; +} + +/** + * @brief Returns the current card's status. + * @param hmmc Pointer to MMC handle + * @param pCardStatus pointer to the buffer that will contain the MMC card + * status (Card Status register) + * @retval error state + */ +static uint32_t MMC_SendStatus(MMC_HandleTypeDef *hmmc, uint32_t *pCardStatus) +{ + uint32_t errorstate = HAL_MMC_ERROR_NONE; + + if(pCardStatus == NULL) + { + return HAL_MMC_ERROR_PARAM; + } + + /* Send Status command */ + errorstate = SDMMC_CmdSendStatus(hmmc->Instance, (uint32_t)(hmmc->MmcCard.RelCardAdd << 16U)); + if(errorstate != HAL_OK) + { + return errorstate; + } + + /* Get MMC card status */ + *pCardStatus = SDIO_GetResponse(hmmc->Instance, SDIO_RESP1); + + return HAL_MMC_ERROR_NONE; +} + +/** + * @brief Wrap up reading in non-blocking mode. + * @param hmmc pointer to a MMC_HandleTypeDef structure that contains + * the configuration information. + * @retval HAL status + */ +static HAL_StatusTypeDef MMC_Read_IT(MMC_HandleTypeDef *hmmc) +{ + uint32_t count = 0U; + uint32_t* tmp; + + tmp = (uint32_t*)hmmc->pRxBuffPtr; + + /* Read data from SDMMC Rx FIFO */ + for(count = 0U; count < 8U; count++) + { + *(tmp + count) = SDIO_ReadFIFO(hmmc->Instance); + } + + hmmc->pRxBuffPtr += 8U; + + return HAL_OK; +} + +/** + * @brief Wrap up writing in non-blocking mode. + * @param hmmc pointer to a MMC_HandleTypeDef structure that contains + * the configuration information. + * @retval HAL status + */ +static HAL_StatusTypeDef MMC_Write_IT(MMC_HandleTypeDef *hmmc) +{ + uint32_t count = 0U; + uint32_t* tmp; + + tmp = (uint32_t*)hmmc->pTxBuffPtr; + + /* Write data to SDMMC Tx FIFO */ + for(count = 0U; count < 8U; count++) + { + SDIO_WriteFIFO(hmmc->Instance, (tmp + count)); + } + + hmmc->pTxBuffPtr += 8U; + + return HAL_OK; +} + +/** + * @} + */ + +#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || + STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || + STM32F412Rx || STM32F412Cx || STM32F413xx || STM32F423xx */ + +#endif /* HAL_MMC_MODULE_ENABLED */ + +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/