diff wiki/Hardware Ressources.md @ 38:5f11787b4f42

include in ostc4 repository
author heinrichsweikamp
date Sat, 28 Apr 2018 11:52:34 +0200
parents
children
line wrap: on
line diff
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/wiki/Hardware Ressources.md	Sat Apr 28 11:52:34 2018 +0200
@@ -0,0 +1,56 @@
+# OSTC4 Resources #
+
+## Hardware ##
+
+There are two processors in the OSTC4:
+
+* an [STM32F427IIT6](http://www.st.com/content/st_com/en/products/microcontrollers/stm32-32-bit-arm-cortex-mcus/stm32-high-performance-mcus/stm32f4-series/stm32f427-437/stm32f427ii.html) as main processor. It is a Cortex-M4 processor with FPU, running at 180 MHz.
+It crunches most of the decompression code, the graphic display operations and the user interface.
+
+* an [STM32F411RET6](http://www.st.com/en/microcontrollers/stm32f411re.html) as the RTE (Real-Time-Environment) processor.
+This is another processor of the ARM Cortex M4 family, but with extremely low power modes and plenty of communication ports.
+It runs real-time gas exchange simulation during dive, and interface to most peripherals.
+
+Various peripherals are connected to them:
+
+- A 800x480 pixels _LCD_ screen, with a live stream of color pixels send by an auto-refresh SDRAM.
+- A pressure sensor.
+- A magnetic compass.
+- An ambient light sensor.
+- Three buttons.
+- A battery, and a battery gauge.
+
+_OSTC4_ programming is based on the _HAL_ (for _Hardware Abstraction Layer_) provided by _ST_.
+This allows to have a more readable C code, and to evolve more easily to another processors of the same familly.
+
+## Drivers Used by the Main CPU - aka CPU1-Discovery ##
+
+The main _ARM-Cortex 4_ CPU uses the following resources provided by the
+_HAL_ (_Hardware Abstraction Layer_)
+provided by the processors makers _ST_ to ease code developement, security and portability:
+
+- **HAL_DMA** _Direct Memory Accelerator_: automated memory transfers, used to manage SPI reception and transmission channels.
+- **HAL_DMA2D** : a _specialized DMA dedicated to images manipulation_, used by `gfx_engine`to clear screens.
+- **HAL_FMC** _Flexible Memory Controller_ to drice the external SDRAM used for display.
+- **HAL_GPIO** _General Purpose Input/Output_: this is the programmable pins of the chip, used to connect nearly evrything.
+- **HAL_LTDC** _LCD TFT Display Controller_: to transfer images to the screen memory ?
+- **HAL_NVIC** _Nested Vector Interrupt Controller_: CORTEX IRQs used in `base.c` to handle buttons interrupts, in `gfx_engine.c` to manage VSYNC (screen's vertical sync) and in `stm32f4xx_hal_msp_hw2.c` to manage all other interrupts (ticks, DMA, DMA2D, TIM and USART).
+- **HAL_RCC** _Reset and Clock Control_: used in `base.c` to setup system, PLL and screen clocks.
+- **HAL_SDRAM** RAM controller used in `stm32f4xx_hal_msp_hw2.c` and in `base.c` to interface the external memory used by the screen.
+- **HAL_SPI** _Serial Peripheral Interface_: implement the [standard SPI protocol](https://en.wikipedia.org/wiki/Serial_Peripheral_Interface_Bus). Used to do full duplex communication between the two CPU in `data_exchange_main.c` to exchange dive settings and state, and in `externCPU2bootloader.c` to send firmware to _CPU2-RTE_. 
+- **HAL_TIM** basic _Timers_ used in `base.c` and PWM (_Pulse Width Modulation_) used to control backlight intensity.
+- **HAL_UART** _Universal Asynchronous Receiver Transmitter_: serial communications used in `bonnexConnect.c`, `ostc.c`, `stm32f4xx_hal_msp_hw2.c`, `tCCR.c`, `tCpmm.c` and `tDebug.c`
+
+## Drivers Used by the Secondary CPU - aka CPU2-RTE ##
+
+- **HAL_ADC** _Analog to Digital Converter_ channel 1 is used in `adc.c` for the ambient light sensor.
+- **HAL_DMA** _Direct Memory Accelerator_: automated memory transfers, used to manage SPI reception and transmission channels when communicating to main CPU.
+- **HAL_FLASH** allow erasing, programming, and managing read/write protection mechanisms of the internal FLASH memory.
+- **HAL_GPIO** _General Purpose Input/Output_: this is the programmable pins of the chip, used to connect nearly evrything.
+- **HAL_I2C** _Inter-Integrated Circuit_ [bus controller](https://en.wikipedia.org/wiki/I2C) is another standard bus, used to connect the pressure sensor in `pressure.c`, the magnetic compass in `compass.c` and the battery state in `batteryGauge.c`. Initialisations are in `baseCPU2.c` and `stm32f4xx_hal_msp_v3.c`.
+- **HAL_NVIC** _Nested Vector Interrupt Controller_: CORTEX IRQs used in `baseCPU2.c` to handle clock ticks, buttons and wireless state. In `spi.c` to know end of SPI transmissions. And in `stm32f4xx_hal_msp_v3.c` to setup various _I2C_ interupts.
+- **HAL_PWR** _Power Controller_: to manage sleep mode, low power and wakeup. And in `rtc.c` to manage FLASH power down.
+- **HAL_RCC** _Reset and Clock Control_: used in `baseCPU2.c` to setup system, PLL clocks for ...
+- **HAL_RTC** _Real Time Clock_ to handle date and time in `scheduler.c`
+- **HAL_SPI** _Serial Peripheral Interface_: implement the [standard protocol](https://en.wikipedia.org/wiki/Serial_Peripheral_Interface_Bus). Used to do full duplex communication between the two CPUs. In `spi.c`, SPI1 is used to communicate to the maon CPU, and SPI3 to commicate to buttons.
+- **HAL_UART** _Universal Asynchronous Receiver Transmitter_: serial communications used in `uart.c`