Mercurial > public > ostc4
comparison Common/Drivers/STM32F4xx_HAL_DRIVER_v120/Inc/stm32f4xx_hal_conf_template.h @ 38:5f11787b4f42
include in ostc4 repository
author | heinrichsweikamp |
---|---|
date | Sat, 28 Apr 2018 11:52:34 +0200 |
parents | |
children |
comparison
equal
deleted
inserted
replaced
37:ccc45c0e1ea2 | 38:5f11787b4f42 |
---|---|
1 /** | |
2 ****************************************************************************** | |
3 * @file stm32f4xx_hal_conf_template.h | |
4 * @author MCD Application Team | |
5 * @version V1.2.0 | |
6 * @date 26-December-2014 | |
7 * @brief HAL configuration template file. | |
8 * This file should be copied to the application folder and renamed | |
9 * to stm32f4xx_hal_conf.h. | |
10 ****************************************************************************** | |
11 * @attention | |
12 * | |
13 * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> | |
14 * | |
15 * Redistribution and use in source and binary forms, with or without modification, | |
16 * are permitted provided that the following conditions are met: | |
17 * 1. Redistributions of source code must retain the above copyright notice, | |
18 * this list of conditions and the following disclaimer. | |
19 * 2. Redistributions in binary form must reproduce the above copyright notice, | |
20 * this list of conditions and the following disclaimer in the documentation | |
21 * and/or other materials provided with the distribution. | |
22 * 3. Neither the name of STMicroelectronics nor the names of its contributors | |
23 * may be used to endorse or promote products derived from this software | |
24 * without specific prior written permission. | |
25 * | |
26 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" | |
27 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE | |
28 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE | |
29 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE | |
30 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
31 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR | |
32 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER | |
33 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, | |
34 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE | |
35 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. | |
36 * | |
37 ****************************************************************************** | |
38 */ | |
39 | |
40 /* Define to prevent recursive inclusion -------------------------------------*/ | |
41 #ifndef __STM32F4xx_HAL_CONF_H | |
42 #define __STM32F4xx_HAL_CONF_H | |
43 | |
44 #ifdef __cplusplus | |
45 extern "C" { | |
46 #endif | |
47 | |
48 /* Exported types ------------------------------------------------------------*/ | |
49 /* Exported constants --------------------------------------------------------*/ | |
50 | |
51 /* ########################## Module Selection ############################## */ | |
52 /** | |
53 * @brief This is the list of modules to be used in the HAL driver | |
54 */ | |
55 #define HAL_MODULE_ENABLED | |
56 #define HAL_ADC_MODULE_ENABLED | |
57 #define HAL_CAN_MODULE_ENABLED | |
58 #define HAL_CRC_MODULE_ENABLED | |
59 #define HAL_CRYP_MODULE_ENABLED | |
60 #define HAL_DAC_MODULE_ENABLED | |
61 #define HAL_DCMI_MODULE_ENABLED | |
62 #define HAL_DMA_MODULE_ENABLED | |
63 #define HAL_DMA2D_MODULE_ENABLED | |
64 #define HAL_ETH_MODULE_ENABLED | |
65 #define HAL_FLASH_MODULE_ENABLED | |
66 #define HAL_NAND_MODULE_ENABLED | |
67 #define HAL_NOR_MODULE_ENABLED | |
68 #define HAL_PCCARD_MODULE_ENABLED | |
69 #define HAL_SRAM_MODULE_ENABLED | |
70 #define HAL_SDRAM_MODULE_ENABLED | |
71 #define HAL_HASH_MODULE_ENABLED | |
72 #define HAL_GPIO_MODULE_ENABLED | |
73 #define HAL_I2C_MODULE_ENABLED | |
74 #define HAL_I2S_MODULE_ENABLED | |
75 #define HAL_IWDG_MODULE_ENABLED | |
76 #define HAL_LTDC_MODULE_ENABLED | |
77 #define HAL_PWR_MODULE_ENABLED | |
78 #define HAL_RCC_MODULE_ENABLED | |
79 #define HAL_RNG_MODULE_ENABLED | |
80 #define HAL_RTC_MODULE_ENABLED | |
81 #define HAL_SAI_MODULE_ENABLED | |
82 #define HAL_SD_MODULE_ENABLED | |
83 #define HAL_SPI_MODULE_ENABLED | |
84 #define HAL_TIM_MODULE_ENABLED | |
85 #define HAL_UART_MODULE_ENABLED | |
86 #define HAL_USART_MODULE_ENABLED | |
87 #define HAL_IRDA_MODULE_ENABLED | |
88 #define HAL_SMARTCARD_MODULE_ENABLED | |
89 #define HAL_WWDG_MODULE_ENABLED | |
90 #define HAL_CORTEX_MODULE_ENABLED | |
91 #define HAL_PCD_MODULE_ENABLED | |
92 #define HAL_HCD_MODULE_ENABLED | |
93 | |
94 | |
95 /* ########################## HSE/HSI Values adaptation ##################### */ | |
96 /** | |
97 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. | |
98 * This value is used by the RCC HAL module to compute the system frequency | |
99 * (when HSE is used as system clock source, directly or through the PLL). | |
100 */ | |
101 #if !defined (HSE_VALUE) | |
102 #define HSE_VALUE ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */ | |
103 #endif /* HSE_VALUE */ | |
104 | |
105 #if !defined (HSE_STARTUP_TIMEOUT) | |
106 #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */ | |
107 #endif /* HSE_STARTUP_TIMEOUT */ | |
108 | |
109 /** | |
110 * @brief Internal High Speed oscillator (HSI) value. | |
111 * This value is used by the RCC HAL module to compute the system frequency | |
112 * (when HSI is used as system clock source, directly or through the PLL). | |
113 */ | |
114 #if !defined (HSI_VALUE) | |
115 #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/ | |
116 #endif /* HSI_VALUE */ | |
117 | |
118 /** | |
119 * @brief Internal Low Speed oscillator (LSI) value. | |
120 */ | |
121 #if !defined (LSI_VALUE) | |
122 #define LSI_VALUE ((uint32_t)32000) /*!< LSI Typical Value in Hz*/ | |
123 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz | |
124 The real value may vary depending on the variations | |
125 in voltage and temperature.*/ | |
126 /** | |
127 * @brief External Low Speed oscillator (LSE) value. | |
128 */ | |
129 #if !defined (LSE_VALUE) | |
130 #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */ | |
131 #endif /* LSE_VALUE */ | |
132 | |
133 /** | |
134 * @brief External clock source for I2S peripheral | |
135 * This value is used by the I2S HAL module to compute the I2S clock source | |
136 * frequency, this source is inserted directly through I2S_CKIN pad. | |
137 */ | |
138 #if !defined (EXTERNAL_CLOCK_VALUE) | |
139 #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) /*!< Value of the Internal oscillator in Hz*/ | |
140 #endif /* EXTERNAL_CLOCK_VALUE */ | |
141 | |
142 /* Tip: To avoid modifying this file each time you need to use different HSE, | |
143 === you can define the HSE value in your toolchain compiler preprocessor. */ | |
144 | |
145 /* ########################### System Configuration ######################### */ | |
146 /** | |
147 * @brief This is the HAL system configuration section | |
148 */ | |
149 #define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ | |
150 #define TICK_INT_PRIORITY ((uint32_t)0x0F) /*!< tick interrupt priority */ | |
151 #define USE_RTOS 0 | |
152 #define PREFETCH_ENABLE 1 | |
153 #define INSTRUCTION_CACHE_ENABLE 1 | |
154 #define DATA_CACHE_ENABLE 1 | |
155 | |
156 /* ########################## Assert Selection ############################## */ | |
157 /** | |
158 * @brief Uncomment the line below to expanse the "assert_param" macro in the | |
159 * HAL drivers code | |
160 */ | |
161 /* #define USE_FULL_ASSERT 1 */ | |
162 | |
163 /* ################## Ethernet peripheral configuration ##################### */ | |
164 | |
165 /* Section 1 : Ethernet peripheral configuration */ | |
166 | |
167 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ | |
168 #define MAC_ADDR0 2 | |
169 #define MAC_ADDR1 0 | |
170 #define MAC_ADDR2 0 | |
171 #define MAC_ADDR3 0 | |
172 #define MAC_ADDR4 0 | |
173 #define MAC_ADDR5 0 | |
174 | |
175 /* Definition of the Ethernet driver buffers size and count */ | |
176 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ | |
177 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ | |
178 #define ETH_RXBUFNB ((uint32_t)4) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ | |
179 #define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ | |
180 | |
181 /* Section 2: PHY configuration section */ | |
182 | |
183 /* DP83848 PHY Address*/ | |
184 #define DP83848_PHY_ADDRESS 0x01 | |
185 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ | |
186 #define PHY_RESET_DELAY ((uint32_t)0x000000FF) | |
187 /* PHY Configuration delay */ | |
188 #define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF) | |
189 | |
190 #define PHY_READ_TO ((uint32_t)0x0000FFFF) | |
191 #define PHY_WRITE_TO ((uint32_t)0x0000FFFF) | |
192 | |
193 /* Section 3: Common PHY Registers */ | |
194 | |
195 #define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */ | |
196 #define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */ | |
197 | |
198 #define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ | |
199 #define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ | |
200 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ | |
201 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ | |
202 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ | |
203 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ | |
204 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ | |
205 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ | |
206 #define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ | |
207 #define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ | |
208 | |
209 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ | |
210 #define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ | |
211 #define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ | |
212 | |
213 /* Section 4: Extended PHY Registers */ | |
214 | |
215 #define PHY_SR ((uint16_t)0x10) /*!< PHY status register Offset */ | |
216 #define PHY_MICR ((uint16_t)0x11) /*!< MII Interrupt Control Register */ | |
217 #define PHY_MISR ((uint16_t)0x12) /*!< MII Interrupt Status and Misc. Control Register */ | |
218 | |
219 #define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ | |
220 #define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ | |
221 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ | |
222 | |
223 #define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ | |
224 #define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ | |
225 | |
226 #define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ | |
227 #define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ | |
228 | |
229 /* Includes ------------------------------------------------------------------*/ | |
230 /** | |
231 * @brief Include module's header file | |
232 */ | |
233 | |
234 #ifdef HAL_RCC_MODULE_ENABLED | |
235 #include "stm32f4xx_hal_rcc.h" | |
236 #endif /* HAL_RCC_MODULE_ENABLED */ | |
237 | |
238 #ifdef HAL_GPIO_MODULE_ENABLED | |
239 #include "stm32f4xx_hal_gpio.h" | |
240 #endif /* HAL_GPIO_MODULE_ENABLED */ | |
241 | |
242 #ifdef HAL_DMA_MODULE_ENABLED | |
243 #include "stm32f4xx_hal_dma.h" | |
244 #endif /* HAL_DMA_MODULE_ENABLED */ | |
245 | |
246 #ifdef HAL_CORTEX_MODULE_ENABLED | |
247 #include "stm32f4xx_hal_cortex.h" | |
248 #endif /* HAL_CORTEX_MODULE_ENABLED */ | |
249 | |
250 #ifdef HAL_ADC_MODULE_ENABLED | |
251 #include "stm32f4xx_hal_adc.h" | |
252 #endif /* HAL_ADC_MODULE_ENABLED */ | |
253 | |
254 #ifdef HAL_CAN_MODULE_ENABLED | |
255 #include "stm32f4xx_hal_can.h" | |
256 #endif /* HAL_CAN_MODULE_ENABLED */ | |
257 | |
258 #ifdef HAL_CRC_MODULE_ENABLED | |
259 #include "stm32f4xx_hal_crc.h" | |
260 #endif /* HAL_CRC_MODULE_ENABLED */ | |
261 | |
262 #ifdef HAL_CRYP_MODULE_ENABLED | |
263 #include "stm32f4xx_hal_cryp.h" | |
264 #endif /* HAL_CRYP_MODULE_ENABLED */ | |
265 | |
266 #ifdef HAL_DMA2D_MODULE_ENABLED | |
267 #include "stm32f4xx_hal_dma2d.h" | |
268 #endif /* HAL_DMA2D_MODULE_ENABLED */ | |
269 | |
270 #ifdef HAL_DAC_MODULE_ENABLED | |
271 #include "stm32f4xx_hal_dac.h" | |
272 #endif /* HAL_DAC_MODULE_ENABLED */ | |
273 | |
274 #ifdef HAL_DCMI_MODULE_ENABLED | |
275 #include "stm32f4xx_hal_dcmi.h" | |
276 #endif /* HAL_DCMI_MODULE_ENABLED */ | |
277 | |
278 #ifdef HAL_ETH_MODULE_ENABLED | |
279 #include "stm32f4xx_hal_eth.h" | |
280 #endif /* HAL_ETH_MODULE_ENABLED */ | |
281 | |
282 #ifdef HAL_FLASH_MODULE_ENABLED | |
283 #include "stm32f4xx_hal_flash.h" | |
284 #endif /* HAL_FLASH_MODULE_ENABLED */ | |
285 | |
286 #ifdef HAL_SRAM_MODULE_ENABLED | |
287 #include "stm32f4xx_hal_sram.h" | |
288 #endif /* HAL_SRAM_MODULE_ENABLED */ | |
289 | |
290 #ifdef HAL_NOR_MODULE_ENABLED | |
291 #include "stm32f4xx_hal_nor.h" | |
292 #endif /* HAL_NOR_MODULE_ENABLED */ | |
293 | |
294 #ifdef HAL_NAND_MODULE_ENABLED | |
295 #include "stm32f4xx_hal_nand.h" | |
296 #endif /* HAL_NAND_MODULE_ENABLED */ | |
297 | |
298 #ifdef HAL_PCCARD_MODULE_ENABLED | |
299 #include "stm32f4xx_hal_pccard.h" | |
300 #endif /* HAL_PCCARD_MODULE_ENABLED */ | |
301 | |
302 #ifdef HAL_SDRAM_MODULE_ENABLED | |
303 #include "stm32f4xx_hal_sdram.h" | |
304 #endif /* HAL_SDRAM_MODULE_ENABLED */ | |
305 | |
306 #ifdef HAL_HASH_MODULE_ENABLED | |
307 #include "stm32f4xx_hal_hash.h" | |
308 #endif /* HAL_HASH_MODULE_ENABLED */ | |
309 | |
310 #ifdef HAL_I2C_MODULE_ENABLED | |
311 #include "stm32f4xx_hal_i2c.h" | |
312 #endif /* HAL_I2C_MODULE_ENABLED */ | |
313 | |
314 #ifdef HAL_I2S_MODULE_ENABLED | |
315 #include "stm32f4xx_hal_i2s.h" | |
316 #endif /* HAL_I2S_MODULE_ENABLED */ | |
317 | |
318 #ifdef HAL_IWDG_MODULE_ENABLED | |
319 #include "stm32f4xx_hal_iwdg.h" | |
320 #endif /* HAL_IWDG_MODULE_ENABLED */ | |
321 | |
322 #ifdef HAL_LTDC_MODULE_ENABLED | |
323 #include "stm32f4xx_hal_ltdc.h" | |
324 #endif /* HAL_LTDC_MODULE_ENABLED */ | |
325 | |
326 #ifdef HAL_PWR_MODULE_ENABLED | |
327 #include "stm32f4xx_hal_pwr.h" | |
328 #endif /* HAL_PWR_MODULE_ENABLED */ | |
329 | |
330 #ifdef HAL_RNG_MODULE_ENABLED | |
331 #include "stm32f4xx_hal_rng.h" | |
332 #endif /* HAL_RNG_MODULE_ENABLED */ | |
333 | |
334 #ifdef HAL_RTC_MODULE_ENABLED | |
335 #include "stm32f4xx_hal_rtc.h" | |
336 #endif /* HAL_RTC_MODULE_ENABLED */ | |
337 | |
338 #ifdef HAL_SAI_MODULE_ENABLED | |
339 #include "stm32f4xx_hal_sai.h" | |
340 #endif /* HAL_SAI_MODULE_ENABLED */ | |
341 | |
342 #ifdef HAL_SD_MODULE_ENABLED | |
343 #include "stm32f4xx_hal_sd.h" | |
344 #endif /* HAL_SD_MODULE_ENABLED */ | |
345 | |
346 #ifdef HAL_SPI_MODULE_ENABLED | |
347 #include "stm32f4xx_hal_spi.h" | |
348 #endif /* HAL_SPI_MODULE_ENABLED */ | |
349 | |
350 #ifdef HAL_TIM_MODULE_ENABLED | |
351 #include "stm32f4xx_hal_tim.h" | |
352 #endif /* HAL_TIM_MODULE_ENABLED */ | |
353 | |
354 #ifdef HAL_UART_MODULE_ENABLED | |
355 #include "stm32f4xx_hal_uart.h" | |
356 #endif /* HAL_UART_MODULE_ENABLED */ | |
357 | |
358 #ifdef HAL_USART_MODULE_ENABLED | |
359 #include "stm32f4xx_hal_usart.h" | |
360 #endif /* HAL_USART_MODULE_ENABLED */ | |
361 | |
362 #ifdef HAL_IRDA_MODULE_ENABLED | |
363 #include "stm32f4xx_hal_irda.h" | |
364 #endif /* HAL_IRDA_MODULE_ENABLED */ | |
365 | |
366 #ifdef HAL_SMARTCARD_MODULE_ENABLED | |
367 #include "stm32f4xx_hal_smartcard.h" | |
368 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ | |
369 | |
370 #ifdef HAL_WWDG_MODULE_ENABLED | |
371 #include "stm32f4xx_hal_wwdg.h" | |
372 #endif /* HAL_WWDG_MODULE_ENABLED */ | |
373 | |
374 #ifdef HAL_PCD_MODULE_ENABLED | |
375 #include "stm32f4xx_hal_pcd.h" | |
376 #endif /* HAL_PCD_MODULE_ENABLED */ | |
377 | |
378 #ifdef HAL_HCD_MODULE_ENABLED | |
379 #include "stm32f4xx_hal_hcd.h" | |
380 #endif /* HAL_HCD_MODULE_ENABLED */ | |
381 | |
382 /* Exported macro ------------------------------------------------------------*/ | |
383 #ifdef USE_FULL_ASSERT | |
384 /** | |
385 * @brief The assert_param macro is used for function's parameters check. | |
386 * @param expr: If expr is false, it calls assert_failed function | |
387 * which reports the name of the source file and the source | |
388 * line number of the call that failed. | |
389 * If expr is true, it returns no value. | |
390 * @retval None | |
391 */ | |
392 #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) | |
393 /* Exported functions ------------------------------------------------------- */ | |
394 void assert_failed(uint8_t* file, uint32_t line); | |
395 #else | |
396 #define assert_param(expr) ((void)0) | |
397 #endif /* USE_FULL_ASSERT */ | |
398 | |
399 | |
400 #ifdef __cplusplus | |
401 } | |
402 #endif | |
403 | |
404 #endif /* __STM32F4xx_HAL_CONF_H */ | |
405 | |
406 | |
407 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |