|
38
|
1 /**
|
|
|
2 ******************************************************************************
|
|
|
3 * @file stm32f4xx_hal_sd.h
|
|
|
4 * @author MCD Application Team
|
|
|
5 * @version V1.2.0
|
|
|
6 * @date 26-December-2014
|
|
|
7 * @brief Header file of SD HAL module.
|
|
|
8 ******************************************************************************
|
|
|
9 * @attention
|
|
|
10 *
|
|
|
11 * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
|
|
|
12 *
|
|
|
13 * Redistribution and use in source and binary forms, with or without modification,
|
|
|
14 * are permitted provided that the following conditions are met:
|
|
|
15 * 1. Redistributions of source code must retain the above copyright notice,
|
|
|
16 * this list of conditions and the following disclaimer.
|
|
|
17 * 2. Redistributions in binary form must reproduce the above copyright notice,
|
|
|
18 * this list of conditions and the following disclaimer in the documentation
|
|
|
19 * and/or other materials provided with the distribution.
|
|
|
20 * 3. Neither the name of STMicroelectronics nor the names of its contributors
|
|
|
21 * may be used to endorse or promote products derived from this software
|
|
|
22 * without specific prior written permission.
|
|
|
23 *
|
|
|
24 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
|
|
25 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
|
26 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
|
|
27 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
|
|
|
28 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
|
29 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
|
30 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
|
|
|
31 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
|
|
32 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
|
|
33 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
|
34 *
|
|
|
35 ******************************************************************************
|
|
|
36 */
|
|
|
37
|
|
|
38 /* Define to prevent recursive inclusion -------------------------------------*/
|
|
|
39 #ifndef __STM32F4xx_HAL_SD_H
|
|
|
40 #define __STM32F4xx_HAL_SD_H
|
|
|
41
|
|
|
42 #ifdef __cplusplus
|
|
|
43 extern "C" {
|
|
|
44 #endif
|
|
|
45
|
|
|
46 /* Includes ------------------------------------------------------------------*/
|
|
|
47 #include "stm32f4xx_ll_sdmmc.h"
|
|
|
48
|
|
|
49 /** @addtogroup STM32F4xx_HAL_Driver
|
|
|
50 * @{
|
|
|
51 */
|
|
|
52
|
|
|
53 /** @defgroup SD SD
|
|
|
54 * @brief SD HAL module driver
|
|
|
55 * @{
|
|
|
56 */
|
|
|
57
|
|
|
58 /* Exported types ------------------------------------------------------------*/
|
|
|
59 /** @defgroup SD_Exported_Types SD Exported Types
|
|
|
60 * @{
|
|
|
61 */
|
|
|
62
|
|
|
63 /** @defgroup SD_Exported_Types_Group1 SD Handle Structure definition
|
|
|
64 * @{
|
|
|
65 */
|
|
|
66 #define SD_InitTypeDef SDIO_InitTypeDef
|
|
|
67 #define SD_TypeDef SDIO_TypeDef
|
|
|
68
|
|
|
69 typedef struct
|
|
|
70 {
|
|
|
71 SD_TypeDef *Instance; /*!< SDIO register base address */
|
|
|
72
|
|
|
73 SD_InitTypeDef Init; /*!< SD required parameters */
|
|
|
74
|
|
|
75 HAL_LockTypeDef Lock; /*!< SD locking object */
|
|
|
76
|
|
|
77 uint32_t CardType; /*!< SD card type */
|
|
|
78
|
|
|
79 uint32_t RCA; /*!< SD relative card address */
|
|
|
80
|
|
|
81 uint32_t CSD[4]; /*!< SD card specific data table */
|
|
|
82
|
|
|
83 uint32_t CID[4]; /*!< SD card identification number table */
|
|
|
84
|
|
|
85 __IO uint32_t SdTransferCplt; /*!< SD transfer complete flag in non blocking mode */
|
|
|
86
|
|
|
87 __IO uint32_t SdTransferErr; /*!< SD transfer error flag in non blocking mode */
|
|
|
88
|
|
|
89 __IO uint32_t DmaTransferCplt; /*!< SD DMA transfer complete flag */
|
|
|
90
|
|
|
91 __IO uint32_t SdOperation; /*!< SD transfer operation (read/write) */
|
|
|
92
|
|
|
93 DMA_HandleTypeDef *hdmarx; /*!< SD Rx DMA handle parameters */
|
|
|
94
|
|
|
95 DMA_HandleTypeDef *hdmatx; /*!< SD Tx DMA handle parameters */
|
|
|
96
|
|
|
97 }SD_HandleTypeDef;
|
|
|
98 /**
|
|
|
99 * @}
|
|
|
100 */
|
|
|
101
|
|
|
102 /** @defgroup SD_Exported_Types_Group2 Card Specific Data: CSD Register
|
|
|
103 * @{
|
|
|
104 */
|
|
|
105 typedef struct
|
|
|
106 {
|
|
|
107 __IO uint8_t CSDStruct; /*!< CSD structure */
|
|
|
108 __IO uint8_t SysSpecVersion; /*!< System specification version */
|
|
|
109 __IO uint8_t Reserved1; /*!< Reserved */
|
|
|
110 __IO uint8_t TAAC; /*!< Data read access time 1 */
|
|
|
111 __IO uint8_t NSAC; /*!< Data read access time 2 in CLK cycles */
|
|
|
112 __IO uint8_t MaxBusClkFrec; /*!< Max. bus clock frequency */
|
|
|
113 __IO uint16_t CardComdClasses; /*!< Card command classes */
|
|
|
114 __IO uint8_t RdBlockLen; /*!< Max. read data block length */
|
|
|
115 __IO uint8_t PartBlockRead; /*!< Partial blocks for read allowed */
|
|
|
116 __IO uint8_t WrBlockMisalign; /*!< Write block misalignment */
|
|
|
117 __IO uint8_t RdBlockMisalign; /*!< Read block misalignment */
|
|
|
118 __IO uint8_t DSRImpl; /*!< DSR implemented */
|
|
|
119 __IO uint8_t Reserved2; /*!< Reserved */
|
|
|
120 __IO uint32_t DeviceSize; /*!< Device Size */
|
|
|
121 __IO uint8_t MaxRdCurrentVDDMin; /*!< Max. read current @ VDD min */
|
|
|
122 __IO uint8_t MaxRdCurrentVDDMax; /*!< Max. read current @ VDD max */
|
|
|
123 __IO uint8_t MaxWrCurrentVDDMin; /*!< Max. write current @ VDD min */
|
|
|
124 __IO uint8_t MaxWrCurrentVDDMax; /*!< Max. write current @ VDD max */
|
|
|
125 __IO uint8_t DeviceSizeMul; /*!< Device size multiplier */
|
|
|
126 __IO uint8_t EraseGrSize; /*!< Erase group size */
|
|
|
127 __IO uint8_t EraseGrMul; /*!< Erase group size multiplier */
|
|
|
128 __IO uint8_t WrProtectGrSize; /*!< Write protect group size */
|
|
|
129 __IO uint8_t WrProtectGrEnable; /*!< Write protect group enable */
|
|
|
130 __IO uint8_t ManDeflECC; /*!< Manufacturer default ECC */
|
|
|
131 __IO uint8_t WrSpeedFact; /*!< Write speed factor */
|
|
|
132 __IO uint8_t MaxWrBlockLen; /*!< Max. write data block length */
|
|
|
133 __IO uint8_t WriteBlockPaPartial; /*!< Partial blocks for write allowed */
|
|
|
134 __IO uint8_t Reserved3; /*!< Reserved */
|
|
|
135 __IO uint8_t ContentProtectAppli; /*!< Content protection application */
|
|
|
136 __IO uint8_t FileFormatGrouop; /*!< File format group */
|
|
|
137 __IO uint8_t CopyFlag; /*!< Copy flag (OTP) */
|
|
|
138 __IO uint8_t PermWrProtect; /*!< Permanent write protection */
|
|
|
139 __IO uint8_t TempWrProtect; /*!< Temporary write protection */
|
|
|
140 __IO uint8_t FileFormat; /*!< File format */
|
|
|
141 __IO uint8_t ECC; /*!< ECC code */
|
|
|
142 __IO uint8_t CSD_CRC; /*!< CSD CRC */
|
|
|
143 __IO uint8_t Reserved4; /*!< Always 1 */
|
|
|
144
|
|
|
145 }HAL_SD_CSDTypedef;
|
|
|
146 /**
|
|
|
147 * @}
|
|
|
148 */
|
|
|
149
|
|
|
150 /** @defgroup SD_Exported_Types_Group3 Card Identification Data: CID Register
|
|
|
151 * @{
|
|
|
152 */
|
|
|
153 typedef struct
|
|
|
154 {
|
|
|
155 __IO uint8_t ManufacturerID; /*!< Manufacturer ID */
|
|
|
156 __IO uint16_t OEM_AppliID; /*!< OEM/Application ID */
|
|
|
157 __IO uint32_t ProdName1; /*!< Product Name part1 */
|
|
|
158 __IO uint8_t ProdName2; /*!< Product Name part2 */
|
|
|
159 __IO uint8_t ProdRev; /*!< Product Revision */
|
|
|
160 __IO uint32_t ProdSN; /*!< Product Serial Number */
|
|
|
161 __IO uint8_t Reserved1; /*!< Reserved1 */
|
|
|
162 __IO uint16_t ManufactDate; /*!< Manufacturing Date */
|
|
|
163 __IO uint8_t CID_CRC; /*!< CID CRC */
|
|
|
164 __IO uint8_t Reserved2; /*!< Always 1 */
|
|
|
165
|
|
|
166 }HAL_SD_CIDTypedef;
|
|
|
167 /**
|
|
|
168 * @}
|
|
|
169 */
|
|
|
170
|
|
|
171 /** @defgroup SD_Exported_Types_Group4 SD Card Status returned by ACMD13
|
|
|
172 * @{
|
|
|
173 */
|
|
|
174 typedef struct
|
|
|
175 {
|
|
|
176 __IO uint8_t DAT_BUS_WIDTH; /*!< Shows the currently defined data bus width */
|
|
|
177 __IO uint8_t SECURED_MODE; /*!< Card is in secured mode of operation */
|
|
|
178 __IO uint16_t SD_CARD_TYPE; /*!< Carries information about card type */
|
|
|
179 __IO uint32_t SIZE_OF_PROTECTED_AREA; /*!< Carries information about the capacity of protected area */
|
|
|
180 __IO uint8_t SPEED_CLASS; /*!< Carries information about the speed class of the card */
|
|
|
181 __IO uint8_t PERFORMANCE_MOVE; /*!< Carries information about the card's performance move */
|
|
|
182 __IO uint8_t AU_SIZE; /*!< Carries information about the card's allocation unit size */
|
|
|
183 __IO uint16_t ERASE_SIZE; /*!< Determines the number of AUs to be erased in one operation */
|
|
|
184 __IO uint8_t ERASE_TIMEOUT; /*!< Determines the timeout for any number of AU erase */
|
|
|
185 __IO uint8_t ERASE_OFFSET; /*!< Carries information about the erase offset */
|
|
|
186
|
|
|
187 }HAL_SD_CardStatusTypedef;
|
|
|
188 /**
|
|
|
189 * @}
|
|
|
190 */
|
|
|
191
|
|
|
192 /** @defgroup SD_Exported_Types_Group5 SD Card information structure
|
|
|
193 * @{
|
|
|
194 */
|
|
|
195 typedef struct
|
|
|
196 {
|
|
|
197 HAL_SD_CSDTypedef SD_csd; /*!< SD card specific data register */
|
|
|
198 HAL_SD_CIDTypedef SD_cid; /*!< SD card identification number register */
|
|
|
199 uint64_t CardCapacity; /*!< Card capacity */
|
|
|
200 uint32_t CardBlockSize; /*!< Card block size */
|
|
|
201 uint16_t RCA; /*!< SD relative card address */
|
|
|
202 uint8_t CardType; /*!< SD card type */
|
|
|
203
|
|
|
204 }HAL_SD_CardInfoTypedef;
|
|
|
205 /**
|
|
|
206 * @}
|
|
|
207 */
|
|
|
208
|
|
|
209 /** @defgroup SD_Exported_Types_Group6 SD Error status enumeration Structure definition
|
|
|
210 * @{
|
|
|
211 */
|
|
|
212 typedef enum
|
|
|
213 {
|
|
|
214 /**
|
|
|
215 * @brief SD specific error defines
|
|
|
216 */
|
|
|
217 SD_CMD_CRC_FAIL = (1), /*!< Command response received (but CRC check failed) */
|
|
|
218 SD_DATA_CRC_FAIL = (2), /*!< Data block sent/received (CRC check failed) */
|
|
|
219 SD_CMD_RSP_TIMEOUT = (3), /*!< Command response timeout */
|
|
|
220 SD_DATA_TIMEOUT = (4), /*!< Data timeout */
|
|
|
221 SD_TX_UNDERRUN = (5), /*!< Transmit FIFO underrun */
|
|
|
222 SD_RX_OVERRUN = (6), /*!< Receive FIFO overrun */
|
|
|
223 SD_START_BIT_ERR = (7), /*!< Start bit not detected on all data signals in wide bus mode */
|
|
|
224 SD_CMD_OUT_OF_RANGE = (8), /*!< Command's argument was out of range. */
|
|
|
225 SD_ADDR_MISALIGNED = (9), /*!< Misaligned address */
|
|
|
226 SD_BLOCK_LEN_ERR = (10), /*!< Transferred block length is not allowed for the card or the number of transferred bytes does not match the block length */
|
|
|
227 SD_ERASE_SEQ_ERR = (11), /*!< An error in the sequence of erase command occurs. */
|
|
|
228 SD_BAD_ERASE_PARAM = (12), /*!< An invalid selection for erase groups */
|
|
|
229 SD_WRITE_PROT_VIOLATION = (13), /*!< Attempt to program a write protect block */
|
|
|
230 SD_LOCK_UNLOCK_FAILED = (14), /*!< Sequence or password error has been detected in unlock command or if there was an attempt to access a locked card */
|
|
|
231 SD_COM_CRC_FAILED = (15), /*!< CRC check of the previous command failed */
|
|
|
232 SD_ILLEGAL_CMD = (16), /*!< Command is not legal for the card state */
|
|
|
233 SD_CARD_ECC_FAILED = (17), /*!< Card internal ECC was applied but failed to correct the data */
|
|
|
234 SD_CC_ERROR = (18), /*!< Internal card controller error */
|
|
|
235 SD_GENERAL_UNKNOWN_ERROR = (19), /*!< General or unknown error */
|
|
|
236 SD_STREAM_READ_UNDERRUN = (20), /*!< The card could not sustain data transfer in stream read operation. */
|
|
|
237 SD_STREAM_WRITE_OVERRUN = (21), /*!< The card could not sustain data programming in stream mode */
|
|
|
238 SD_CID_CSD_OVERWRITE = (22), /*!< CID/CSD overwrite error */
|
|
|
239 SD_WP_ERASE_SKIP = (23), /*!< Only partial address space was erased */
|
|
|
240 SD_CARD_ECC_DISABLED = (24), /*!< Command has been executed without using internal ECC */
|
|
|
241 SD_ERASE_RESET = (25), /*!< Erase sequence was cleared before executing because an out of erase sequence command was received */
|
|
|
242 SD_AKE_SEQ_ERROR = (26), /*!< Error in sequence of authentication. */
|
|
|
243 SD_INVALID_VOLTRANGE = (27),
|
|
|
244 SD_ADDR_OUT_OF_RANGE = (28),
|
|
|
245 SD_SWITCH_ERROR = (29),
|
|
|
246 SD_SDIO_DISABLED = (30),
|
|
|
247 SD_SDIO_FUNCTION_BUSY = (31),
|
|
|
248 SD_SDIO_FUNCTION_FAILED = (32),
|
|
|
249 SD_SDIO_UNKNOWN_FUNCTION = (33),
|
|
|
250
|
|
|
251 /**
|
|
|
252 * @brief Standard error defines
|
|
|
253 */
|
|
|
254 SD_INTERNAL_ERROR = (34),
|
|
|
255 SD_NOT_CONFIGURED = (35),
|
|
|
256 SD_REQUEST_PENDING = (36),
|
|
|
257 SD_REQUEST_NOT_APPLICABLE = (37),
|
|
|
258 SD_INVALID_PARAMETER = (38),
|
|
|
259 SD_UNSUPPORTED_FEATURE = (39),
|
|
|
260 SD_UNSUPPORTED_HW = (40),
|
|
|
261 SD_ERROR = (41),
|
|
|
262 SD_OK = (0)
|
|
|
263
|
|
|
264 }HAL_SD_ErrorTypedef;
|
|
|
265 /**
|
|
|
266 * @}
|
|
|
267 */
|
|
|
268
|
|
|
269 /** @defgroup SD_Exported_Types_Group7 SD Transfer state enumeration structure
|
|
|
270 * @{
|
|
|
271 */
|
|
|
272 typedef enum
|
|
|
273 {
|
|
|
274 SD_TRANSFER_OK = 0, /*!< Transfer success */
|
|
|
275 SD_TRANSFER_BUSY = 1, /*!< Transfer is occurring */
|
|
|
276 SD_TRANSFER_ERROR = 2 /*!< Transfer failed */
|
|
|
277
|
|
|
278 }HAL_SD_TransferStateTypedef;
|
|
|
279 /**
|
|
|
280 * @}
|
|
|
281 */
|
|
|
282
|
|
|
283 /** @defgroup SD_Exported_Types_Group8 SD Card State enumeration structure
|
|
|
284 * @{
|
|
|
285 */
|
|
|
286 typedef enum
|
|
|
287 {
|
|
|
288 SD_CARD_READY = ((uint32_t)0x00000001), /*!< Card state is ready */
|
|
|
289 SD_CARD_IDENTIFICATION = ((uint32_t)0x00000002), /*!< Card is in identification state */
|
|
|
290 SD_CARD_STANDBY = ((uint32_t)0x00000003), /*!< Card is in standby state */
|
|
|
291 SD_CARD_TRANSFER = ((uint32_t)0x00000004), /*!< Card is in transfer state */
|
|
|
292 SD_CARD_SENDING = ((uint32_t)0x00000005), /*!< Card is sending an operation */
|
|
|
293 SD_CARD_RECEIVING = ((uint32_t)0x00000006), /*!< Card is receiving operation information */
|
|
|
294 SD_CARD_PROGRAMMING = ((uint32_t)0x00000007), /*!< Card is in programming state */
|
|
|
295 SD_CARD_DISCONNECTED = ((uint32_t)0x00000008), /*!< Card is disconnected */
|
|
|
296 SD_CARD_ERROR = ((uint32_t)0x000000FF) /*!< Card is in error state */
|
|
|
297
|
|
|
298 }HAL_SD_CardStateTypedef;
|
|
|
299 /**
|
|
|
300 * @}
|
|
|
301 */
|
|
|
302
|
|
|
303 /** @defgroup SD_Exported_Types_Group9 SD Operation enumeration structure
|
|
|
304 * @{
|
|
|
305 */
|
|
|
306 typedef enum
|
|
|
307 {
|
|
|
308 SD_READ_SINGLE_BLOCK = 0, /*!< Read single block operation */
|
|
|
309 SD_READ_MULTIPLE_BLOCK = 1, /*!< Read multiple blocks operation */
|
|
|
310 SD_WRITE_SINGLE_BLOCK = 2, /*!< Write single block operation */
|
|
|
311 SD_WRITE_MULTIPLE_BLOCK = 3 /*!< Write multiple blocks operation */
|
|
|
312
|
|
|
313 }HAL_SD_OperationTypedef;
|
|
|
314 /**
|
|
|
315 * @}
|
|
|
316 */
|
|
|
317
|
|
|
318 /**
|
|
|
319 * @}
|
|
|
320 */
|
|
|
321
|
|
|
322 /* Exported constants --------------------------------------------------------*/
|
|
|
323 /** @defgroup SD_Exported_Constants SD Exported Constants
|
|
|
324 * @{
|
|
|
325 */
|
|
|
326
|
|
|
327 /**
|
|
|
328 * @brief SD Commands Index
|
|
|
329 */
|
|
|
330 #define SD_CMD_GO_IDLE_STATE ((uint8_t)0) /*!< Resets the SD memory card. */
|
|
|
331 #define SD_CMD_SEND_OP_COND ((uint8_t)1) /*!< Sends host capacity support information and activates the card's initialization process. */
|
|
|
332 #define SD_CMD_ALL_SEND_CID ((uint8_t)2) /*!< Asks any card connected to the host to send the CID numbers on the CMD line. */
|
|
|
333 #define SD_CMD_SET_REL_ADDR ((uint8_t)3) /*!< Asks the card to publish a new relative address (RCA). */
|
|
|
334 #define SD_CMD_SET_DSR ((uint8_t)4) /*!< Programs the DSR of all cards. */
|
|
|
335 #define SD_CMD_SDIO_SEN_OP_COND ((uint8_t)5) /*!< Sends host capacity support information (HCS) and asks the accessed card to send its
|
|
|
336 operating condition register (OCR) content in the response on the CMD line. */
|
|
|
337 #define SD_CMD_HS_SWITCH ((uint8_t)6) /*!< Checks switchable function (mode 0) and switch card function (mode 1). */
|
|
|
338 #define SD_CMD_SEL_DESEL_CARD ((uint8_t)7) /*!< Selects the card by its own relative address and gets deselected by any other address */
|
|
|
339 #define SD_CMD_HS_SEND_EXT_CSD ((uint8_t)8) /*!< Sends SD Memory Card interface condition, which includes host supply voltage information
|
|
|
340 and asks the card whether card supports voltage. */
|
|
|
341 #define SD_CMD_SEND_CSD ((uint8_t)9) /*!< Addressed card sends its card specific data (CSD) on the CMD line. */
|
|
|
342 #define SD_CMD_SEND_CID ((uint8_t)10) /*!< Addressed card sends its card identification (CID) on the CMD line. */
|
|
|
343 #define SD_CMD_READ_DAT_UNTIL_STOP ((uint8_t)11) /*!< SD card doesn't support it. */
|
|
|
344 #define SD_CMD_STOP_TRANSMISSION ((uint8_t)12) /*!< Forces the card to stop transmission. */
|
|
|
345 #define SD_CMD_SEND_STATUS ((uint8_t)13) /*!< Addressed card sends its status register. */
|
|
|
346 #define SD_CMD_HS_BUSTEST_READ ((uint8_t)14)
|
|
|
347 #define SD_CMD_GO_INACTIVE_STATE ((uint8_t)15) /*!< Sends an addressed card into the inactive state. */
|
|
|
348 #define SD_CMD_SET_BLOCKLEN ((uint8_t)16) /*!< Sets the block length (in bytes for SDSC) for all following block commands
|
|
|
349 (read, write, lock). Default block length is fixed to 512 Bytes. Not effective
|
|
|
350 for SDHS and SDXC. */
|
|
|
351 #define SD_CMD_READ_SINGLE_BLOCK ((uint8_t)17) /*!< Reads single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of
|
|
|
352 fixed 512 bytes in case of SDHC and SDXC. */
|
|
|
353 #define SD_CMD_READ_MULT_BLOCK ((uint8_t)18) /*!< Continuously transfers data blocks from card to host until interrupted by
|
|
|
354 STOP_TRANSMISSION command. */
|
|
|
355 #define SD_CMD_HS_BUSTEST_WRITE ((uint8_t)19) /*!< 64 bytes tuning pattern is sent for SDR50 and SDR104. */
|
|
|
356 #define SD_CMD_WRITE_DAT_UNTIL_STOP ((uint8_t)20) /*!< Speed class control command. */
|
|
|
357 #define SD_CMD_SET_BLOCK_COUNT ((uint8_t)23) /*!< Specify block count for CMD18 and CMD25. */
|
|
|
358 #define SD_CMD_WRITE_SINGLE_BLOCK ((uint8_t)24) /*!< Writes single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of
|
|
|
359 fixed 512 bytes in case of SDHC and SDXC. */
|
|
|
360 #define SD_CMD_WRITE_MULT_BLOCK ((uint8_t)25) /*!< Continuously writes blocks of data until a STOP_TRANSMISSION follows. */
|
|
|
361 #define SD_CMD_PROG_CID ((uint8_t)26) /*!< Reserved for manufacturers. */
|
|
|
362 #define SD_CMD_PROG_CSD ((uint8_t)27) /*!< Programming of the programmable bits of the CSD. */
|
|
|
363 #define SD_CMD_SET_WRITE_PROT ((uint8_t)28) /*!< Sets the write protection bit of the addressed group. */
|
|
|
364 #define SD_CMD_CLR_WRITE_PROT ((uint8_t)29) /*!< Clears the write protection bit of the addressed group. */
|
|
|
365 #define SD_CMD_SEND_WRITE_PROT ((uint8_t)30) /*!< Asks the card to send the status of the write protection bits. */
|
|
|
366 #define SD_CMD_SD_ERASE_GRP_START ((uint8_t)32) /*!< Sets the address of the first write block to be erased. (For SD card only). */
|
|
|
367 #define SD_CMD_SD_ERASE_GRP_END ((uint8_t)33) /*!< Sets the address of the last write block of the continuous range to be erased. */
|
|
|
368 #define SD_CMD_ERASE_GRP_START ((uint8_t)35) /*!< Sets the address of the first write block to be erased. Reserved for each command
|
|
|
369 system set by switch function command (CMD6). */
|
|
|
370 #define SD_CMD_ERASE_GRP_END ((uint8_t)36) /*!< Sets the address of the last write block of the continuous range to be erased.
|
|
|
371 Reserved for each command system set by switch function command (CMD6). */
|
|
|
372 #define SD_CMD_ERASE ((uint8_t)38) /*!< Reserved for SD security applications. */
|
|
|
373 #define SD_CMD_FAST_IO ((uint8_t)39) /*!< SD card doesn't support it (Reserved). */
|
|
|
374 #define SD_CMD_GO_IRQ_STATE ((uint8_t)40) /*!< SD card doesn't support it (Reserved). */
|
|
|
375 #define SD_CMD_LOCK_UNLOCK ((uint8_t)42) /*!< Sets/resets the password or lock/unlock the card. The size of the data block is set by
|
|
|
376 the SET_BLOCK_LEN command. */
|
|
|
377 #define SD_CMD_APP_CMD ((uint8_t)55) /*!< Indicates to the card that the next command is an application specific command rather
|
|
|
378 than a standard command. */
|
|
|
379 #define SD_CMD_GEN_CMD ((uint8_t)56) /*!< Used either to transfer a data block to the card or to get a data block from the card
|
|
|
380 for general purpose/application specific commands. */
|
|
|
381 #define SD_CMD_NO_CMD ((uint8_t)64)
|
|
|
382
|
|
|
383 /**
|
|
|
384 * @brief Following commands are SD Card Specific commands.
|
|
|
385 * SDIO_APP_CMD should be sent before sending these commands.
|
|
|
386 */
|
|
|
387 #define SD_CMD_APP_SD_SET_BUSWIDTH ((uint8_t)6) /*!< (ACMD6) Defines the data bus width to be used for data transfer. The allowed data bus
|
|
|
388 widths are given in SCR register. */
|
|
|
389 #define SD_CMD_SD_APP_STATUS ((uint8_t)13) /*!< (ACMD13) Sends the SD status. */
|
|
|
390 #define SD_CMD_SD_APP_SEND_NUM_WRITE_BLOCKS ((uint8_t)22) /*!< (ACMD22) Sends the number of the written (without errors) write blocks. Responds with
|
|
|
391 32bit+CRC data block. */
|
|
|
392 #define SD_CMD_SD_APP_OP_COND ((uint8_t)41) /*!< (ACMD41) Sends host capacity support information (HCS) and asks the accessed card to
|
|
|
393 send its operating condition register (OCR) content in the response on the CMD line. */
|
|
|
394 #define SD_CMD_SD_APP_SET_CLR_CARD_DETECT ((uint8_t)42) /*!< (ACMD42) Connects/Disconnects the 50 KOhm pull-up resistor on CD/DAT3 (pin 1) of the card. */
|
|
|
395 #define SD_CMD_SD_APP_SEND_SCR ((uint8_t)51) /*!< Reads the SD Configuration Register (SCR). */
|
|
|
396 #define SD_CMD_SDIO_RW_DIRECT ((uint8_t)52) /*!< For SD I/O card only, reserved for security specification. */
|
|
|
397 #define SD_CMD_SDIO_RW_EXTENDED ((uint8_t)53) /*!< For SD I/O card only, reserved for security specification. */
|
|
|
398
|
|
|
399 /**
|
|
|
400 * @brief Following commands are SD Card Specific security commands.
|
|
|
401 * SD_CMD_APP_CMD should be sent before sending these commands.
|
|
|
402 */
|
|
|
403 #define SD_CMD_SD_APP_GET_MKB ((uint8_t)43) /*!< For SD card only */
|
|
|
404 #define SD_CMD_SD_APP_GET_MID ((uint8_t)44) /*!< For SD card only */
|
|
|
405 #define SD_CMD_SD_APP_SET_CER_RN1 ((uint8_t)45) /*!< For SD card only */
|
|
|
406 #define SD_CMD_SD_APP_GET_CER_RN2 ((uint8_t)46) /*!< For SD card only */
|
|
|
407 #define SD_CMD_SD_APP_SET_CER_RES2 ((uint8_t)47) /*!< For SD card only */
|
|
|
408 #define SD_CMD_SD_APP_GET_CER_RES1 ((uint8_t)48) /*!< For SD card only */
|
|
|
409 #define SD_CMD_SD_APP_SECURE_READ_MULTIPLE_BLOCK ((uint8_t)18) /*!< For SD card only */
|
|
|
410 #define SD_CMD_SD_APP_SECURE_WRITE_MULTIPLE_BLOCK ((uint8_t)25) /*!< For SD card only */
|
|
|
411 #define SD_CMD_SD_APP_SECURE_ERASE ((uint8_t)38) /*!< For SD card only */
|
|
|
412 #define SD_CMD_SD_APP_CHANGE_SECURE_AREA ((uint8_t)49) /*!< For SD card only */
|
|
|
413 #define SD_CMD_SD_APP_SECURE_WRITE_MKB ((uint8_t)48) /*!< For SD card only */
|
|
|
414
|
|
|
415 /**
|
|
|
416 * @brief Supported SD Memory Cards
|
|
|
417 */
|
|
|
418 #define STD_CAPACITY_SD_CARD_V1_1 ((uint32_t)0x00000000)
|
|
|
419 #define STD_CAPACITY_SD_CARD_V2_0 ((uint32_t)0x00000001)
|
|
|
420 #define HIGH_CAPACITY_SD_CARD ((uint32_t)0x00000002)
|
|
|
421 #define MULTIMEDIA_CARD ((uint32_t)0x00000003)
|
|
|
422 #define SECURE_DIGITAL_IO_CARD ((uint32_t)0x00000004)
|
|
|
423 #define HIGH_SPEED_MULTIMEDIA_CARD ((uint32_t)0x00000005)
|
|
|
424 #define SECURE_DIGITAL_IO_COMBO_CARD ((uint32_t)0x00000006)
|
|
|
425 #define HIGH_CAPACITY_MMC_CARD ((uint32_t)0x00000007)
|
|
|
426 /**
|
|
|
427 * @}
|
|
|
428 */
|
|
|
429
|
|
|
430 /* Exported macro ------------------------------------------------------------*/
|
|
|
431 /** @defgroup SD_Exported_macros SD Exported Macros
|
|
|
432 * @brief macros to handle interrupts and specific clock configurations
|
|
|
433 * @{
|
|
|
434 */
|
|
|
435
|
|
|
436 /**
|
|
|
437 * @brief Enable the SD device.
|
|
|
438 * @retval None
|
|
|
439 */
|
|
|
440 #define __HAL_SD_SDIO_ENABLE() __SDIO_ENABLE()
|
|
|
441
|
|
|
442 /**
|
|
|
443 * @brief Disable the SD device.
|
|
|
444 * @retval None
|
|
|
445 */
|
|
|
446 #define __HAL_SD_SDIO_DISABLE() __SDIO_DISABLE()
|
|
|
447
|
|
|
448 /**
|
|
|
449 * @brief Enable the SDIO DMA transfer.
|
|
|
450 * @retval None
|
|
|
451 */
|
|
|
452 #define __HAL_SD_SDIO_DMA_ENABLE() __SDIO_DMA_ENABLE()
|
|
|
453
|
|
|
454 /**
|
|
|
455 * @brief Disable the SDIO DMA transfer.
|
|
|
456 * @retval None
|
|
|
457 */
|
|
|
458 #define __HAL_SD_SDIO_DMA_DISABLE() __SDIO_DMA_DISABLE()
|
|
|
459
|
|
|
460 /**
|
|
|
461 * @brief Enable the SD device interrupt.
|
|
|
462 * @param __HANDLE__: SD Handle
|
|
|
463 * @param __INTERRUPT__: specifies the SDIO interrupt sources to be enabled.
|
|
|
464 * This parameter can be one or a combination of the following values:
|
|
|
465 * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
|
|
|
466 * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
|
|
|
467 * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
|
|
|
468 * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
|
|
|
469 * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
|
|
|
470 * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt
|
|
|
471 * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt
|
|
|
472 * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt
|
|
|
473 * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt
|
|
|
474 * @arg SDIO_IT_STBITERR: Start bit not detected on all data signals in wide
|
|
|
475 * bus mode interrupt
|
|
|
476 * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt
|
|
|
477 * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt
|
|
|
478 * @arg SDIO_IT_TXACT: Data transmit in progress interrupt
|
|
|
479 * @arg SDIO_IT_RXACT: Data receive in progress interrupt
|
|
|
480 * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
|
|
|
481 * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
|
|
|
482 * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt
|
|
|
483 * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt
|
|
|
484 * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt
|
|
|
485 * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt
|
|
|
486 * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt
|
|
|
487 * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt
|
|
|
488 * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt
|
|
|
489 * @arg SDIO_IT_CEATAEND: CE-ATA command completion signal received for CMD61 interrupt
|
|
|
490 * @retval None
|
|
|
491 */
|
|
|
492 #define __HAL_SD_SDIO_ENABLE_IT(__HANDLE__, __INTERRUPT__) __SDIO_ENABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__))
|
|
|
493
|
|
|
494 /**
|
|
|
495 * @brief Disable the SD device interrupt.
|
|
|
496 * @param __HANDLE__: SD Handle
|
|
|
497 * @param __INTERRUPT__: specifies the SDIO interrupt sources to be disabled.
|
|
|
498 * This parameter can be one or a combination of the following values:
|
|
|
499 * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
|
|
|
500 * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
|
|
|
501 * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
|
|
|
502 * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
|
|
|
503 * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
|
|
|
504 * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt
|
|
|
505 * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt
|
|
|
506 * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt
|
|
|
507 * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt
|
|
|
508 * @arg SDIO_IT_STBITERR: Start bit not detected on all data signals in wide
|
|
|
509 * bus mode interrupt
|
|
|
510 * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt
|
|
|
511 * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt
|
|
|
512 * @arg SDIO_IT_TXACT: Data transmit in progress interrupt
|
|
|
513 * @arg SDIO_IT_RXACT: Data receive in progress interrupt
|
|
|
514 * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
|
|
|
515 * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
|
|
|
516 * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt
|
|
|
517 * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt
|
|
|
518 * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt
|
|
|
519 * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt
|
|
|
520 * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt
|
|
|
521 * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt
|
|
|
522 * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt
|
|
|
523 * @arg SDIO_IT_CEATAEND: CE-ATA command completion signal received for CMD61 interrupt
|
|
|
524 * @retval None
|
|
|
525 */
|
|
|
526 #define __HAL_SD_SDIO_DISABLE_IT(__HANDLE__, __INTERRUPT__) __SDIO_DISABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__))
|
|
|
527
|
|
|
528 /**
|
|
|
529 * @brief Check whether the specified SD flag is set or not.
|
|
|
530 * @param __HANDLE__: SD Handle
|
|
|
531 * @param __FLAG__: specifies the flag to check.
|
|
|
532 * This parameter can be one of the following values:
|
|
|
533 * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed)
|
|
|
534 * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed)
|
|
|
535 * @arg SDIO_FLAG_CTIMEOUT: Command response timeout
|
|
|
536 * @arg SDIO_FLAG_DTIMEOUT: Data timeout
|
|
|
537 * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error
|
|
|
538 * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error
|
|
|
539 * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed)
|
|
|
540 * @arg SDIO_FLAG_CMDSENT: Command sent (no response required)
|
|
|
541 * @arg SDIO_FLAG_DATAEND: Data end (data counter, SDIDCOUNT, is zero)
|
|
|
542 * @arg SDIO_FLAG_STBITERR: Start bit not detected on all data signals in wide bus mode.
|
|
|
543 * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed)
|
|
|
544 * @arg SDIO_FLAG_CMDACT: Command transfer in progress
|
|
|
545 * @arg SDIO_FLAG_TXACT: Data transmit in progress
|
|
|
546 * @arg SDIO_FLAG_RXACT: Data receive in progress
|
|
|
547 * @arg SDIO_FLAG_TXFIFOHE: Transmit FIFO Half Empty
|
|
|
548 * @arg SDIO_FLAG_RXFIFOHF: Receive FIFO Half Full
|
|
|
549 * @arg SDIO_FLAG_TXFIFOF: Transmit FIFO full
|
|
|
550 * @arg SDIO_FLAG_RXFIFOF: Receive FIFO full
|
|
|
551 * @arg SDIO_FLAG_TXFIFOE: Transmit FIFO empty
|
|
|
552 * @arg SDIO_FLAG_RXFIFOE: Receive FIFO empty
|
|
|
553 * @arg SDIO_FLAG_TXDAVL: Data available in transmit FIFO
|
|
|
554 * @arg SDIO_FLAG_RXDAVL: Data available in receive FIFO
|
|
|
555 * @arg SDIO_FLAG_SDIOIT: SD I/O interrupt received
|
|
|
556 * @arg SDIO_FLAG_CEATAEND: CE-ATA command completion signal received for CMD61
|
|
|
557 * @retval The new state of SD FLAG (SET or RESET).
|
|
|
558 */
|
|
|
559 #define __HAL_SD_SDIO_GET_FLAG(__HANDLE__, __FLAG__) __SDIO_GET_FLAG((__HANDLE__)->Instance, (__FLAG__))
|
|
|
560
|
|
|
561 /**
|
|
|
562 * @brief Clear the SD's pending flags.
|
|
|
563 * @param __HANDLE__: SD Handle
|
|
|
564 * @param __FLAG__: specifies the flag to clear.
|
|
|
565 * This parameter can be one or a combination of the following values:
|
|
|
566 * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed)
|
|
|
567 * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed)
|
|
|
568 * @arg SDIO_FLAG_CTIMEOUT: Command response timeout
|
|
|
569 * @arg SDIO_FLAG_DTIMEOUT: Data timeout
|
|
|
570 * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error
|
|
|
571 * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error
|
|
|
572 * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed)
|
|
|
573 * @arg SDIO_FLAG_CMDSENT: Command sent (no response required)
|
|
|
574 * @arg SDIO_FLAG_DATAEND: Data end (data counter, SDIDCOUNT, is zero)
|
|
|
575 * @arg SDIO_FLAG_STBITERR: Start bit not detected on all data signals in wide bus mode
|
|
|
576 * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed)
|
|
|
577 * @arg SDIO_FLAG_SDIOIT: SD I/O interrupt received
|
|
|
578 * @arg SDIO_FLAG_CEATAEND: CE-ATA command completion signal received for CMD61
|
|
|
579 * @retval None
|
|
|
580 */
|
|
|
581 #define __HAL_SD_SDIO_CLEAR_FLAG(__HANDLE__, __FLAG__) __SDIO_CLEAR_FLAG((__HANDLE__)->Instance, (__FLAG__))
|
|
|
582
|
|
|
583 /**
|
|
|
584 * @brief Check whether the specified SD interrupt has occurred or not.
|
|
|
585 * @param __HANDLE__: SD Handle
|
|
|
586 * @param __INTERRUPT__: specifies the SDIO interrupt source to check.
|
|
|
587 * This parameter can be one of the following values:
|
|
|
588 * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
|
|
|
589 * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
|
|
|
590 * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
|
|
|
591 * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
|
|
|
592 * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
|
|
|
593 * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt
|
|
|
594 * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt
|
|
|
595 * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt
|
|
|
596 * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt
|
|
|
597 * @arg SDIO_IT_STBITERR: Start bit not detected on all data signals in wide
|
|
|
598 * bus mode interrupt
|
|
|
599 * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt
|
|
|
600 * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt
|
|
|
601 * @arg SDIO_IT_TXACT: Data transmit in progress interrupt
|
|
|
602 * @arg SDIO_IT_RXACT: Data receive in progress interrupt
|
|
|
603 * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
|
|
|
604 * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
|
|
|
605 * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt
|
|
|
606 * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt
|
|
|
607 * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt
|
|
|
608 * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt
|
|
|
609 * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt
|
|
|
610 * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt
|
|
|
611 * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt
|
|
|
612 * @arg SDIO_IT_CEATAEND: CE-ATA command completion signal received for CMD61 interrupt
|
|
|
613 * @retval The new state of SD IT (SET or RESET).
|
|
|
614 */
|
|
|
615 #define __HAL_SD_SDIO_GET_IT (__HANDLE__, __INTERRUPT__) __SDIO_GET_IT ((__HANDLE__)->Instance, __INTERRUPT__)
|
|
|
616
|
|
|
617 /**
|
|
|
618 * @brief Clear the SD's interrupt pending bits.
|
|
|
619 * @param __HANDLE__ : SD Handle
|
|
|
620 * @param __INTERRUPT__: specifies the interrupt pending bit to clear.
|
|
|
621 * This parameter can be one or a combination of the following values:
|
|
|
622 * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
|
|
|
623 * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
|
|
|
624 * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
|
|
|
625 * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
|
|
|
626 * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
|
|
|
627 * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt
|
|
|
628 * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt
|
|
|
629 * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt
|
|
|
630 * @arg SDIO_IT_DATAEND: Data end (data counter, SDIO_DCOUNT, is zero) interrupt
|
|
|
631 * @arg SDIO_IT_STBITERR: Start bit not detected on all data signals in wide
|
|
|
632 * bus mode interrupt
|
|
|
633 * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt
|
|
|
634 * @arg SDIO_IT_CEATAEND: CE-ATA command completion signal received for CMD61
|
|
|
635 * @retval None
|
|
|
636 */
|
|
|
637 #define __HAL_SD_SDIO_CLEAR_IT(__HANDLE__, __INTERRUPT__) __SDIO_CLEAR_IT((__HANDLE__)->Instance, (__INTERRUPT__))
|
|
|
638 /**
|
|
|
639 * @}
|
|
|
640 */
|
|
|
641
|
|
|
642 /* Exported functions --------------------------------------------------------*/
|
|
|
643 /** @defgroup SD_Exported_Functions SD Exported Functions
|
|
|
644 * @{
|
|
|
645 */
|
|
|
646
|
|
|
647 /** @defgroup SD_Exported_Functions_Group1 Initialization and de-initialization functions
|
|
|
648 * @{
|
|
|
649 */
|
|
|
650 HAL_SD_ErrorTypedef HAL_SD_Init(SD_HandleTypeDef *hsd, HAL_SD_CardInfoTypedef *SDCardInfo);
|
|
|
651 HAL_StatusTypeDef HAL_SD_DeInit (SD_HandleTypeDef *hsd);
|
|
|
652 void HAL_SD_MspInit(SD_HandleTypeDef *hsd);
|
|
|
653 void HAL_SD_MspDeInit(SD_HandleTypeDef *hsd);
|
|
|
654 /**
|
|
|
655 * @}
|
|
|
656 */
|
|
|
657
|
|
|
658 /** @defgroup SD_Exported_Functions_Group2 I/O operation functions
|
|
|
659 * @{
|
|
|
660 */
|
|
|
661 /* Blocking mode: Polling */
|
|
|
662 HAL_SD_ErrorTypedef HAL_SD_ReadBlocks(SD_HandleTypeDef *hsd, uint32_t *pReadBuffer, uint64_t ReadAddr, uint32_t BlockSize, uint32_t NumberOfBlocks);
|
|
|
663 HAL_SD_ErrorTypedef HAL_SD_WriteBlocks(SD_HandleTypeDef *hsd, uint32_t *pWriteBuffer, uint64_t WriteAddr, uint32_t BlockSize, uint32_t NumberOfBlocks);
|
|
|
664 HAL_SD_ErrorTypedef HAL_SD_Erase(SD_HandleTypeDef *hsd, uint64_t startaddr, uint64_t endaddr);
|
|
|
665
|
|
|
666 /* Non-Blocking mode: Interrupt */
|
|
|
667 void HAL_SD_IRQHandler(SD_HandleTypeDef *hsd);
|
|
|
668
|
|
|
669 /* Callback in non blocking modes (DMA) */
|
|
|
670 void HAL_SD_DMA_RxCpltCallback(DMA_HandleTypeDef *hdma);
|
|
|
671 void HAL_SD_DMA_RxErrorCallback(DMA_HandleTypeDef *hdma);
|
|
|
672 void HAL_SD_DMA_TxCpltCallback(DMA_HandleTypeDef *hdma);
|
|
|
673 void HAL_SD_DMA_TxErrorCallback(DMA_HandleTypeDef *hdma);
|
|
|
674 void HAL_SD_XferCpltCallback(SD_HandleTypeDef *hsd);
|
|
|
675 void HAL_SD_XferErrorCallback(SD_HandleTypeDef *hsd);
|
|
|
676
|
|
|
677 /* Non-Blocking mode: DMA */
|
|
|
678 HAL_SD_ErrorTypedef HAL_SD_ReadBlocks_DMA(SD_HandleTypeDef *hsd, uint32_t *pReadBuffer, uint64_t ReadAddr, uint32_t BlockSize, uint32_t NumberOfBlocks);
|
|
|
679 HAL_SD_ErrorTypedef HAL_SD_WriteBlocks_DMA(SD_HandleTypeDef *hsd, uint32_t *pWriteBuffer, uint64_t WriteAddr, uint32_t BlockSize, uint32_t NumberOfBlocks);
|
|
|
680 HAL_SD_ErrorTypedef HAL_SD_CheckWriteOperation(SD_HandleTypeDef *hsd, uint32_t Timeout);
|
|
|
681 HAL_SD_ErrorTypedef HAL_SD_CheckReadOperation(SD_HandleTypeDef *hsd, uint32_t Timeout);
|
|
|
682 /**
|
|
|
683 * @}
|
|
|
684 */
|
|
|
685
|
|
|
686 /** @defgroup SD_Exported_Functions_Group3 Peripheral Control functions
|
|
|
687 * @{
|
|
|
688 */
|
|
|
689 HAL_SD_ErrorTypedef HAL_SD_Get_CardInfo(SD_HandleTypeDef *hsd, HAL_SD_CardInfoTypedef *pCardInfo);
|
|
|
690 HAL_SD_ErrorTypedef HAL_SD_WideBusOperation_Config(SD_HandleTypeDef *hsd, uint32_t WideMode);
|
|
|
691 HAL_SD_ErrorTypedef HAL_SD_StopTransfer(SD_HandleTypeDef *hsd);
|
|
|
692 HAL_SD_ErrorTypedef HAL_SD_HighSpeed (SD_HandleTypeDef *hsd);
|
|
|
693 /**
|
|
|
694 * @}
|
|
|
695 */
|
|
|
696
|
|
|
697 /* Peripheral State functions ************************************************/
|
|
|
698 /** @defgroup SD_Exported_Functions_Group4 Peripheral State functions
|
|
|
699 * @{
|
|
|
700 */
|
|
|
701 HAL_SD_ErrorTypedef HAL_SD_SendSDStatus(SD_HandleTypeDef *hsd, uint32_t *pSDstatus);
|
|
|
702 HAL_SD_ErrorTypedef HAL_SD_GetCardStatus(SD_HandleTypeDef *hsd, HAL_SD_CardStatusTypedef *pCardStatus);
|
|
|
703 HAL_SD_TransferStateTypedef HAL_SD_GetStatus(SD_HandleTypeDef *hsd);
|
|
|
704 /**
|
|
|
705 * @}
|
|
|
706 */
|
|
|
707
|
|
|
708 /**
|
|
|
709 * @}
|
|
|
710 */
|
|
|
711
|
|
|
712 /* Private types -------------------------------------------------------------*/
|
|
|
713 /** @defgroup SD_Private_Types SD Private Types
|
|
|
714 * @{
|
|
|
715 */
|
|
|
716
|
|
|
717 /**
|
|
|
718 * @}
|
|
|
719 */
|
|
|
720
|
|
|
721 /* Private defines -----------------------------------------------------------*/
|
|
|
722 /** @defgroup SD_Private_Defines SD Private Defines
|
|
|
723 * @{
|
|
|
724 */
|
|
|
725
|
|
|
726 /**
|
|
|
727 * @}
|
|
|
728 */
|
|
|
729
|
|
|
730 /* Private variables ---------------------------------------------------------*/
|
|
|
731 /** @defgroup SD_Private_Variables SD Private Variables
|
|
|
732 * @{
|
|
|
733 */
|
|
|
734
|
|
|
735 /**
|
|
|
736 * @}
|
|
|
737 */
|
|
|
738
|
|
|
739 /* Private constants ---------------------------------------------------------*/
|
|
|
740 /** @defgroup SD_Private_Constants SD Private Constants
|
|
|
741 * @{
|
|
|
742 */
|
|
|
743
|
|
|
744 /**
|
|
|
745 * @}
|
|
|
746 */
|
|
|
747
|
|
|
748 /* Private macros ------------------------------------------------------------*/
|
|
|
749 /** @defgroup SD_Private_Macros SD Private Macros
|
|
|
750 * @{
|
|
|
751 */
|
|
|
752
|
|
|
753 /**
|
|
|
754 * @}
|
|
|
755 */
|
|
|
756
|
|
|
757 /* Private functions prototypes ----------------------------------------------*/
|
|
|
758 /** @defgroup SD_Private_Functions_Prototypes SD Private Functions Prototypes
|
|
|
759 * @{
|
|
|
760 */
|
|
|
761
|
|
|
762 /**
|
|
|
763 * @}
|
|
|
764 */
|
|
|
765
|
|
|
766 /* Private functions ---------------------------------------------------------*/
|
|
|
767 /** @defgroup SD_Private_Functions SD Private Functions
|
|
|
768 * @{
|
|
|
769 */
|
|
|
770
|
|
|
771 /**
|
|
|
772 * @}
|
|
|
773 */
|
|
|
774
|
|
|
775 /**
|
|
|
776 * @}
|
|
|
777 */
|
|
|
778
|
|
|
779 /**
|
|
|
780 * @}
|
|
|
781 */
|
|
|
782
|
|
|
783 #ifdef __cplusplus
|
|
|
784 }
|
|
|
785 #endif
|
|
|
786
|
|
|
787 #endif /* __STM32F4xx_HAL_SD_H */
|
|
|
788
|
|
|
789 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|
