Mercurial > public > ostc4
annotate Small_CPU/Inc/batteryCharger.h @ 845:17d9d6eddd8d Evo_2_23
Added new PreDiveCheck info page:
In case a DiveO2 sensor is connected to the OSTC than the values of the DiveO2 internal pressure and temperature sensors may be used for predive checks. The pressure sensors is used for over / under pressure test and the values are visualized using a graph to make it easier to check if the pressure keeps stable. The temperature measurement gives an indication if the scrubber is getting active. This view is highly dependend on the surface temperature but may be useful e.g. for diving in european area.
In addition the values ofthe connected sensors are shown.
| author | Ideenmodellierer |
|---|---|
| date | Sun, 21 Jan 2024 22:24:36 +0100 |
| parents | 1b995079c045 |
| children | d32901746950 |
| rev | line source |
|---|---|
| 38 | 1 /** |
| 2 ****************************************************************************** | |
| 3 * @file batteryCharger.h | |
| 4 * @author heinrichs weikamp gmbh | |
| 5 * @date 09-Dec-2014 | |
| 6 * @version V0.0.1 | |
| 7 * @since 09-Dec-2014 | |
| 8 * @brief LTC4054 Standalone Linear Li-Ion Battery Charger | |
| 9 * | |
| 10 @verbatim | |
| 11 ============================================================================== | |
| 12 ##### How to use ##### | |
| 13 ============================================================================== | |
| 14 @endverbatim | |
| 15 ****************************************************************************** | |
| 16 * @attention | |
| 17 * | |
| 18 * <h2><center>© COPYRIGHT(c) 2015 heinrichs weikamp</center></h2> | |
| 19 * | |
| 20 ****************************************************************************** | |
| 21 */ | |
| 22 | |
| 23 /* Define to prevent recursive inclusion -------------------------------------*/ | |
| 24 #ifndef BATTERY_CHARGER_H | |
| 25 #define BATTERY_CHARGER_H | |
| 26 | |
| 27 #ifdef __cplusplus | |
| 28 extern "C" { | |
| 29 #endif | |
| 30 | |
| 31 /* Includes ------------------------------------------------------------------*/ | |
| 32 #include <stdint.h> | |
| 33 | |
| 662 | 34 #define CHARGE_IN_PIN GPIO_PIN_2 |
| 35 #define CHARGE_IN_GPIO_PORT GPIOC | |
| 36 #define CHARGE_IN_GPIO_ENABLE() __GPIOC_CLK_ENABLE() | |
| 37 | |
| 38 #define CHARGE_OUT_PIN GPIO_PIN_1 | |
| 39 #define CHARGE_OUT_GPIO_PORT GPIOC | |
| 40 #define CHARGE_OUT_GPIO_ENABLE() __GPIOC_CLK_ENABLE() | |
| 38 | 41 |
| 662 | 42 typedef enum |
| 43 { | |
| 44 Charger_NotConnected = 0, /* This is identified reading CHARGE_IN_PIN == HIGH */ | |
| 45 Charger_WarmUp, /* Charging started but counter did not yet reach a certain limit (used to debounce connect / disconnect events to avoid multiple increases of statistic charging cycle counter) */ | |
| 46 Charger_Active, /* Charging identified by CHARGE_IN_PIN == LOW for a certain time */ | |
| 47 Charger_Finished, | |
| 48 Charger_LostConnection, /* Intermediate state to debounce disconnecting events (including charging error state like over temperature) */ | |
| 49 Charger_ColdStart, /* Cold start condition => check if an loaded battery has been inserted */ | |
| 50 Charger_END | |
| 51 } chargerState_t; | |
| 52 | |
| 53 | |
| 54 uint8_t get_charge_status(void); | |
| 38 | 55 void init_battery_charger_status(void); |
| 662 | 56 void set_charge_state(chargerState_t newState); |
| 57 uint8_t get_charge_state(void); | |
| 38 | 58 void ReInit_battery_charger_status_pins(void); |
| 59 void DeInit_battery_charger_status_pins(void); | |
|
643
5149cd644fbc
Reimplemented charger status generation (deactivated):
Ideenmodellierer
parents:
38
diff
changeset
|
60 void battery_charger_get_status_and_contral_battery_gas_gauge(uint8_t cycleTimeBase); |
| 38 | 61 |
| 62 #ifdef __cplusplus | |
| 63 } | |
| 64 #endif | |
| 65 | |
| 66 #endif /* BATTERY_CHARGER_H */ | |
| 67 | |
| 68 /************************ (C) COPYRIGHT heinrichs weikamp *****END OF FILE****/ |