| Fri, 01 Sep 2017 13:18:38 +0200 |
heinrichsweikamp |
2.23beta release
|
| Tue, 22 Aug 2017 13:23:52 +0200 |
heinrichsweikamp |
NEW: Show a warning for each sensor if the sensor is end-of-life after calibration (Less then 8mV in Air at sea level)
|
| Mon, 21 Aug 2017 14:55:36 +0200 |
heinrichsweikamp |
CHANGE: CCR Calibration gas range limited to O2% 21-25 and 95-100 to save button presses
|
| Thu, 17 Aug 2017 13:20:03 +0200 |
heinrichsweikamp |
2.20beta release
|
| Sun, 06 Aug 2017 20:12:49 +0200 |
heinrichsweikamp |
BUGFIX: Ignore "Toggle GF" Menu entry (in divemode) when using the non-GF deco mode
|
| Sat, 05 Aug 2017 17:36:58 +0200 |
heinrichsweikamp |
BUGFIX: O2 as diluent in CCR caused wrong calculations (Deco, EAD, END) in less then 6m depth
|
| Sat, 05 Aug 2017 16:50:28 +0200 |
heinrichsweikamp |
BUGFIX: Skip MOD Test for CCR in Sensor modes (OSTC cR and OSTC3 only)
|
| Sat, 05 Aug 2017 15:04:08 +0200 |
heinrichsweikamp |
BUGFIX: Do not show GF in divemode for non-GF deco mode
|
| Fri, 04 Aug 2017 19:20:58 +0200 |
heinrichsweikamp |
BUGFIX: Menu tree cleaned up (Exited to CCR menu from simulator settings)
|
| Fri, 04 Aug 2017 16:19:50 +0200 |
heinrichsweikamp |
BUGFIX: Impossible fixed-ppO2 (e.g. 1,6bar in 3m) used for tissue calculations
|
| Fri, 04 Aug 2017 16:01:28 +0200 |
heinrichsweikamp |
CHANGE: Apply safety margin parameters to both models (GF and non-GF)
|
| Thu, 03 Aug 2017 17:17:25 +0200 |
heinrichsweikamp |
BUGFIX: Do not check ppO2 for disabled gases
|
| Thu, 03 Aug 2017 17:03:05 +0200 |
heinrichsweikamp |
CHANGE: Show actual GF (Not relative) in custom views in dive mode
|
| Thu, 03 Aug 2017 16:59:31 +0200 |
heinrichsweikamp |
NEW: ppO2 blinks in sensor mode when min/max boundaries are hit
|
| Tue, 04 Jul 2017 16:12:53 +0200 |
heinrichsweikamp |
BUGFIX: Lost Diluent now possible in CCR and PSCR mode
|
| Thu, 29 Jun 2017 11:48:13 +0200 |
heinrichsweikamp |
2.20 RC1
|
| Thu, 29 Jun 2017 11:47:08 +0200 |
heinrichsweikamp |
2.18 beta release
|
| Tue, 27 Jun 2017 13:50:42 +0200 |
heinrichsweikamp |
NEW: Two ppO2 max settings. One for travel/bottom and one for deco gases
|
| Mon, 26 Jun 2017 13:02:04 +0200 |
heinrichsweikamp |
BUGFIX: PSCR mode "Better Gas" showed bailout gases instead of diluents
|
| Mon, 26 Jun 2017 12:30:54 +0200 |
heinrichsweikamp |
BUGFIX: Reset to MOD in Diluent Menu did reset Setpoint change depth
|
| Sun, 11 Jun 2017 17:11:40 +0200 |
heinrichsweikamp |
NEW: Last Dive customviews in surface mode with divetime, depth and interval
|
| Fri, 09 Jun 2017 14:47:02 +0200 |
heinrichsweikamp |
BUGFIX: PSCR mode showed bailout gaslist instead of diluent gaslist
|
| Thu, 11 May 2017 15:39:40 +0200 |
heinrichsweikamp |
Battery % in logbook when updated from Sport to Tech
|
| Mon, 08 May 2017 12:52:49 +0200 |
heinrichsweikamp |
minor
|
| Thu, 30 Mar 2017 11:28:40 +0200 |
heinrichsweikamp |
2.15 rc
|
| Wed, 29 Mar 2017 21:35:12 +0200 |
heinrichsweikamp |
NEW: Deep Sleep mode for OSTC Plus and OSTC 2 (2017) (Entered automatically)
|
| Mon, 20 Feb 2017 15:51:51 +0100 |
heinrichsweikamp |
2.15 start...
|
| Mon, 06 Feb 2017 16:26:36 +0100 |
heinrichsweikamp |
NEW: PSCR mode (Passive semi-closed rebreather)
|
| Wed, 01 Feb 2017 13:51:59 +0100 |
heinrichsweikamp |
BUGFIX: Layout fixes in Gauge mode (German and French language only)
|
| Mon, 16 Jan 2017 11:59:55 +0100 |
heinrichsweikamp |
NEW: Show battery type in surface mode next to battery voltage
|
| Sun, 18 Dec 2016 18:20:39 +0100 |
heinrichsweikamp |
CHANGE: Show warnings either in Customview (If active) _or_ next to warning sign
|
| Sun, 11 Dec 2016 14:43:56 +0100 |
heinrichsweikamp |
NEW: New Customview 11 in dive mode shows ppO2, EAD/END and CNS
|
| Fri, 18 Nov 2016 10:49:32 +0100 |
heinrichsweikamp |
BUGFIX: Minor layout corrections in imperial units dive screen
|
| Wed, 02 Nov 2016 15:46:22 +0100 |
heinrichsweikamp |
CHANGE: Easier to understand "New Battery" menu (OSTC model dependent)
|
| Fri, 28 Oct 2016 11:30:50 +0200 |
heinrichsweikamp |
CHANGE: Indicate "Bailout" for bailout deco plan in internal deco planer
|
| Mon, 10 Oct 2016 10:59:19 +0200 |
heinrichsweikamp |
2.10 release
|
| Tue, 27 Sep 2016 16:40:14 +0200 |
heinrichsweikamp |
NEW: Store more battery info into logbook memory
|
| Mon, 19 Sep 2016 16:32:02 +0200 |
heinrichsweikamp |
NEW: Show Uptime (Time since last firmware boot) in information menu
|
| Thu, 01 Sep 2016 13:28:15 +0200 |
heinrichsweikamp |
changelog
|
| Tue, 30 Aug 2016 17:26:21 +0200 |
heinrichsweikamp |
work on new battery options
|
| Wed, 17 Aug 2016 09:50:37 +0200 |
heinrichsweikamp |
Adjustable timeout for Divemode (Config 0x48)
|
| Tue, 26 Jul 2016 12:08:29 +0200 |
heinrichsweikamp |
+BUGFIX: Compatibility with "hwOS Config" fixed
|
| Thu, 30 Jun 2016 10:28:12 +0200 |
heinrichsweikamp |
CHANGE: Language fixes, 2.08 release
|
| Thu, 23 Jun 2016 10:59:42 +0200 |
heinrichsweikamp |
Logbook marker temporally disabled in internal logbook
|
| Thu, 12 May 2016 14:58:32 +0200 |
heinrichsweikamp |
ignore 0x47 for standard hwOS
|
| Mon, 25 Apr 2016 15:25:32 +0200 |
heinrichsweikamp |
CHANGE: Remove ppO2 [Dil] from OC dive mode screen
|
| Mon, 18 Apr 2016 14:34:57 +0200 |
heinrichsweikamp |
NEW: Support for new logbook memory chip (minor hardware change)
|
| Tue, 22 Mar 2016 16:39:00 +0100 |
heinrichsweikamp |
NEW: New Customview shows ppO2(O2) and ppO2(Diluent) during CCR mode
|
| Fri, 11 Mar 2016 10:11:07 +0100 |
heinrichsweikamp |
BUGFIX: Fix missing ccr setup menu (From 2.02)
|
| Tue, 08 Mar 2016 11:42:58 +0100 |
heinrichsweikamp |
BUGFIX: Fix rare issue after battery change (OSTC3 did not start properly)
|
| Tue, 02 Feb 2016 11:09:14 +0100 |
heinrichsweikamp |
2.01 release
|
| Tue, 02 Feb 2016 10:40:52 +0100 |
heinrichsweikamp |
changelog
|
| Mon, 01 Feb 2016 20:44:01 +0100 |
heinrichsweikamp |
BUGFIX: Divetime >99mins was not displayed (Only OSTC2 with serial >= )
|
| Sun, 10 Jan 2016 11:24:33 +0100 |
heinrichsweikamp |
NEW: "Lost Gas" feature allows disabling gases during the dive
|
| Sun, 10 Jan 2016 09:36:47 +0100 |
heinrichsweikamp |
NEW: Logbook shows markers with small orange boxes in the profile
|
| Sat, 09 Jan 2016 11:42:01 +0100 |
heinrichsweikamp |
Logbook marker can be set in dive mode menu (OC only)
|
| Tue, 24 Nov 2015 16:22:52 +0100 |
heinrichsweikamp |
CHANGE: New segmented speed graph in divemode
|
| Mon, 23 Nov 2015 16:13:25 +0100 |
heinrichsweikamp |
BUGFIX: Make sure SP1 is always selected on start in Auto-SP mode
|
| Mon, 16 Nov 2015 11:04:27 +0100 |
heinrichsweikamp |
1.93 release
|
| Fri, 06 Nov 2015 11:48:40 +0100 |
heinrichsweikamp |
BUGFIX: minor text allignment in CCR mode
|
| Thu, 05 Nov 2015 20:15:52 +0100 |
heinrichsweikamp |
tweak response timing in comm mode
|
| Tue, 03 Nov 2015 11:35:29 +0100 |
heinrichsweikamp |
NEW: Show actual dive count in logbook list view (If <1000)
|
| Tue, 27 Oct 2015 13:45:10 +0100 |
heinrichsweikamp |
CHANGE: Logbook now shows end-of-dive date and time for dives made with firmware <1.92 indicated by an icon in the logbook
|
| Mon, 19 Oct 2015 15:06:59 +0200 |
heinrichsweikamp |
BUGFIX: German texts in ppo2 menu were too long for screen resulting in resulting in text display issues
|
| Wed, 07 Oct 2015 14:46:39 +0200 |
heinrichsweikamp |
some cleanups, jump to 1.90 stable
|
| Wed, 07 Oct 2015 13:14:09 +0200 |
heinrichsweikamp |
BUGFIX: +5min for stopwatch during simulation did not work
|
| Wed, 23 Sep 2015 17:35:19 +0200 |
heinrichsweikamp |
allow compass bearing on surface
|
| Sat, 19 Sep 2015 13:41:40 +0200 |
heinrichsweikamp |
BUGFIX: Battery consumption calculation in sleep mode (3,6V battery only)
|
| Tue, 15 Sep 2015 18:11:08 +0200 |
heinrichsweikamp |
BUGFIX: BLE timings for MAC issues
|
| Mon, 07 Sep 2015 13:58:23 +0200 |
heinrichsweikamp |
CHANGE: Do not show ppO2 in warning area if already shown in custom view
|
| Thu, 27 Aug 2015 17:05:13 +0200 |
heinrichsweikamp |
1.88 release, BUGFIX: Start with Sensor use from sleep (cR only), CHANGE: Apply button settings when button menu is closed, NEW: Reset button settings on a magnet reset (cR and OSTC 2)
|
| Fri, 21 Aug 2015 18:37:52 +0200 |
heinrichsweikamp |
1.87 release
|
| Sun, 16 Aug 2015 15:16:23 +0200 |
heinrichsweikamp |
Additional temperature calibration via PC interface
|
| Tue, 04 Aug 2015 11:20:34 +0200 |
heinrichsweikamp |
changelog
|
| Mon, 03 Aug 2015 22:47:39 +0200 |
heinrichsweikamp |
hardware support
|
| Sun, 02 Aug 2015 16:52:31 +0200 |
heinrichsweikamp |
BUGFIX: Auto-Brightness clipped to lowest settings in bright sunlight on some devices
|
| Tue, 28 Jul 2015 16:32:55 +0200 |
heinrichsweikamp |
NEW: Quit Simulator automatically when starting a real dive
|
| Tue, 21 Jul 2015 12:08:01 +0200 |
heinrichsweikamp |
New option to download "Compact Headers". Improved BLE support (OSTC 2 and OSTC 3+), updated OSTC interface documentation
|
| Mon, 20 Jul 2015 15:04:13 +0200 |
heinrichsweikamp |
CHANGE: GF and aGF high range increased to 45-110%
|
| Mon, 20 Jul 2015 12:43:42 +0200 |
heinrichsweikamp |
BUGFIX: Rotate button sensitivity with screen (OSTC 2 and cR)
|
| Fri, 03 Jul 2015 15:46:56 +0200 |
heinrichsweikamp |
changelog
|
| Fri, 03 Jul 2015 14:47:04 +0200 |
heinrichsweikamp |
NEW: Mode Auto SP: Automatically switches the SP during descent (CC Mode)
|
| Sun, 28 Jun 2015 13:58:00 +0200 |
heinrichsweikamp |
cleanup menu, add "Auto SP" option (Not working yet), minor layout change in compass menu
|
| Tue, 26 May 2015 17:40:13 +0200 |
heinrichsweikamp |
BUGFIX: Fix download issue for dives made with 1.80 firmware
|
| Mon, 18 May 2015 21:25:56 +0200 |
heinrichsweikamp |
BUGFIX: There was a 1:4096 chance that a portion of a dive was not stored correctly resulting in download issues
|
| Thu, 07 May 2015 13:11:14 +0200 |
heinrichsweikamp |
rename into hwOS
|
| Tue, 05 May 2015 14:58:16 +0200 |
heinrichsweikamp |
BUGFIX: Fast Gas change near the ppO2 limit could cause switching to a non-available Gas #0
|
| Mon, 04 May 2015 12:56:07 +0200 |
heinrichsweikamp |
CHANGE: Automatically abort connection fail after 2mins (Bluetooth only)
|
| Wed, 29 Apr 2015 16:54:58 +0200 |
heinrichsweikamp |
1.78 release
|
| Sun, 19 Apr 2015 20:41:48 +0200 |
heinrichsweikamp |
BUGFIX: Increase timing tolerance for S8 HUD (cR only)
|
| Thu, 16 Apr 2015 11:30:00 +0200 |
heinrichsweikamp |
BUGFIX: Analog sensors were ignored in 1.76
|
| Tue, 14 Apr 2015 16:16:14 +0200 |
heinrichsweikamp |
Charge done indicator (cR and 2 Hardware)
|
| Mon, 30 Mar 2015 14:59:07 +0200 |
heinrichsweikamp |
1.76 release
|
| Fri, 13 Mar 2015 10:49:43 +0100 |
heinrichsweikamp |
BUGFIX: Always update CCR sensor data in Sensor-Menu
|
| Sun, 01 Mar 2015 21:10:14 +0100 |
heinrichsweikamp |
CNANGE: aGF pair has same range then normal GF pair
|
| Thu, 26 Feb 2015 13:13:23 +0100 |
heinrichsweikamp |
1.75 release
|
| Wed, 25 Feb 2015 11:51:50 +0100 |
heinrichsweikamp |
show start gas in normal font
|
| Sat, 21 Feb 2015 20:05:57 +0100 |
mh |
BUGFIX: Show average depth with one decimal digit only
|
| Mon, 02 Feb 2015 17:39:38 +0100 |
heinrichsweikamp |
NEW: Support for hwHUD without the LED module
|
| Sun, 01 Feb 2015 18:49:24 +0100 |
heinrichsweikamp |
BUGFIX: Show dives with >999mins divetime correctly
|
| Wed, 14 Jan 2015 11:37:19 +0100 |
heinrichsweikamp |
PC config, 1.72 release
|
| Tue, 06 Jan 2015 19:24:58 +0100 |
heinrichsweikamp |
check opt_max correctly
|
| Wed, 17 Dec 2014 14:46:45 +0100 |
heinrichsweikamp |
1.7 release
|
| Mon, 15 Dec 2014 19:50:51 +0100 |
heinrichsweikamp |
NEW: On-board simulator can increase divetime in 5min steps
|
| Sun, 07 Dec 2014 12:47:19 +0100 |
heinrichsweikamp |
NEW: Show plan parameters in decoplan result page
|
| Mon, 10 Nov 2014 13:54:20 +0100 |
heinrichsweikamp |
(Slightly) reduce current consumption in Eco and sleep mode
|
| Mon, 27 Oct 2014 11:28:48 +0100 |
heinrichsweikamp |
NEW: Show Bailout Gas List in Surface mode (CCR Modes)
|
| Sat, 25 Oct 2014 15:28:18 +0200 |
heinrichsweikamp |
CHANGE: Longer timeout (4 min) for calibration menu
|
| Sat, 18 Oct 2014 10:03:28 +0200 |
heinrichsweikamp |
BUGFIX: Check min and max values after PC configuration properly
|
| Fri, 17 Oct 2014 13:31:14 +0200 |
heinrichsweikamp |
BUGFIX: Quit Apnea mode on the surface manually
|
| Thu, 16 Oct 2014 13:11:18 +0200 |
heinrichsweikamp |
BUGFIX: O2 > 99% was not configurable from the PC
|
| Thu, 09 Oct 2014 11:18:56 +0200 |
heinrichsweikamp |
BUGFIX: END/EAD updated when adjusting current gas during the dive
|
| Tue, 07 Oct 2014 13:45:21 +0200 |
heinrichsweikamp |
BUGFIX: Average depth computation
|
| Mon, 06 Oct 2014 11:48:23 +0200 |
heinrichsweikamp |
CHANGE: Draw a frame around the dive mode menu
|
| Sun, 05 Oct 2014 15:36:17 +0200 |
heinrichsweikamp |
CHANGE: Clarify Travel Gases with "---" as change depth
|
| Wed, 01 Oct 2014 10:31:53 +0200 |
heinrichsweikamp |
minor
|
| Tue, 30 Sep 2014 10:35:47 +0200 |
heinrichsweikamp |
CHANGE: Compass readout smoothed
|
| Mon, 29 Sep 2014 22:26:47 +0200 |
heinrichsweikamp |
CHANGE: Improve internal logbook usability
|
| Mon, 29 Sep 2014 12:03:26 +0200 |
heinrichsweikamp |
BUGFIX: False max. temp in Logbook, false Bailout and Gas 6 flags in logbook
|
| Sun, 28 Sep 2014 18:44:07 +0200 |
heinrichsweikamp |
BUGFIX: Flip compass with flipped screen, too
|
