Mercurial > public > hwos_code
graph
-
2.25 stable RC2017-09-07, by heinrichsweikamp
-
BUGFIX: Simulator in CC mode2017-09-06, by heinrichsweikamp
-
NEW: Show Compass calibration results in Compass menu2017-09-06, by heinrichsweikamp
-
BUGFIX: "lost gas" showed current set of gases (Diluents in CC, OC in Bailout) for both "lost gas" menus2017-09-06, by heinrichsweikamp
-
minor simulator fix2017-09-05, by heinrichsweikamp
-
2.23beta release2017-09-01, by heinrichsweikamp
-
Re-insert Rev. 530 changes into gaslist.asm2017-08-28, by heinrichsweikamp
-
2.23 start2017-08-28, by heinrichsweikamp
-
2.22 internal release2017-08-25, by heinrichsweikamp
-
minor2017-08-23, by heinrichsweikamp
-
update customview mask to (eventually) rewrite ppO2(Dil): to ppO2:2017-08-22, by heinrichsweikamp
-
NEW: Show a warning for each sensor if the sensor is end-of-life after calibration (Less then 8mV in Air at sea level)2017-08-22, by heinrichsweikamp
-
Setpoint Change Depth Fix2017-08-21, by heinrichsweikamp
-
CHANGE: CCR Calibration gas range limited to O2% 21-25 and 95-100 to save button presses2017-08-21, by heinrichsweikamp
-
Minor French text update, roll-back gaslist.asm changes2017-08-21, by heinrichsweikamp
-
2.21 start2017-08-18, by heinrichsweikamp
-
2.20beta release2017-08-17, by heinrichsweikamp
-
minor2017-08-07, by heinrichsweikamp
-
BUGFIX: Ignore "Toggle GF" Menu entry (in divemode) when using the non-GF deco mode2017-08-06, by heinrichsweikamp
-
BUGFIX: O2 as diluent in CCR caused wrong calculations (Deco, EAD, END) in less then 6m depth2017-08-05, by heinrichsweikamp
-
BUGFIX: Skip MOD Test for CCR in Sensor modes (OSTC cR and OSTC3 only)2017-08-05, by heinrichsweikamp
-
BUGFIX: Do not show GF in divemode for non-GF deco mode2017-08-05, by heinrichsweikamp
-
menu work2017-08-05, by heinrichsweikamp
-
BUGFIX: Menu tree cleaned up (Exited to CCR menu from simulator settings)2017-08-04, by heinrichsweikamp
-
BUGFIX: Impossible fixed-ppO2 (e.g. 1,6bar in 3m) used for tissue calculations2017-08-04, by heinrichsweikamp
-
CHANGE: Apply safety margin parameters to both models (GF and non-GF)2017-08-04, by heinrichsweikamp
-
Excel sheets for debugging nofly time from Ralph Lembcke2017-08-04, by heinrichsweikamp
-
minor2017-08-03, by heinrichsweikamp
-
BUGFIX: Do not check ppO2 for disabled gases2017-08-03, by heinrichsweikamp
-
CHANGE: Show actual GF (Not relative) in custom views in dive mode2017-08-03, by heinrichsweikamp
-
NEW: ppO2 blinks in sensor mode when min/max boundaries are hit2017-08-03, by heinrichsweikamp
-
docu update2017-08-03, by heinrichsweikamp
-
hex build2017-07-15, by heinrichsweikamp
-
minor2017-07-11, by heinrichsweikamp
-
minor2017-07-04, by heinrichsweikamp
-
BUGFIX: Lost Diluent now possible in CCR and PSCR mode2017-07-04, by heinrichsweikamp
-
BUGFIX: Planner in CCR mode used OC gases for volume calculations in some cases2017-06-30, by heinrichsweikamp
-
2.20 RC12017-06-29, by heinrichsweikamp
-
2.18 beta release2017-06-29, by heinrichsweikamp
-
NEW: Two ppO2 max settings. One for travel/bottom and one for deco gases2017-06-27, by heinrichsweikamp
-
BUGFIX: PSCR mode "Better Gas" showed bailout gases instead of diluents2017-06-26, by heinrichsweikamp
-
BUGFIX: Reset to MOD in Diluent Menu did reset Setpoint change depth2017-06-26, by heinrichsweikamp
-
minor2017-06-24, by heinrichsweikamp
-
NEW: Last Dive customviews in surface mode with divetime, depth and interval2017-06-11, by heinrichsweikamp
-
BUGFIX: PSCR mode showed bailout gaslist instead of diluent gaslist2017-06-09, by heinrichsweikamp
-
minor2017-05-22, by heinrichsweikamp
-
Battery % in logbook when updated from Sport to Tech2017-05-11, by heinrichsweikamp
-
minor2017-05-08, by heinrichsweikamp
-
compass1 full scale gain test2017-04-19, by heinrichsweikamp
-
2.15 release2017-04-03, by heinrichsweikamp
-
show battery % in logbook (For dives made with 2.15 or newer)2017-04-02, by heinrichsweikamp
-
Bugfix: More then one marker shown deleted profile2017-04-02, by heinrichsweikamp
-
2.15 rc2017-03-30, by heinrichsweikamp
-
2.15 rc2017-03-30, by heinrichsweikamp
-
2.15 rc2017-03-30, by heinrichsweikamp
-
minor new sleepmode fix2017-03-30, by heinrichsweikamp
-
NEW: Deep Sleep mode for OSTC Plus and OSTC 2 (2017) (Entered automatically)2017-03-29, by heinrichsweikamp
-
docu (battery info byte)2017-03-27, by heinrichsweikamp
-
docu update2017-03-27, by heinrichsweikamp
-
minor2017-03-13, by heinrichsweikamp
-
2.15 start...2017-02-20, by heinrichsweikamp
-
3.14 BETA release2017-02-20, by heinrichsweikamp
-
minor2017-02-20, by heinrichsweikamp
-
Make opt_PSCR_drop and opt_PSCR_lungratio PC configurable2017-02-20, by heinrichsweikamp
-
New customview #12 for PSCR mode shows ppO2, O2 drop and lung ratio2017-02-07, by heinrichsweikamp
-
cleanup pscr menu2017-02-06, by heinrichsweikamp
-
NEW: PSCR mode (Passive semi-closed rebreather)2017-02-06, by heinrichsweikamp
-
BUGFIX: Layout fixes in Gauge mode (German and French language only)2017-02-01, by heinrichsweikamp
-
2.12 release2017-01-17, by heinrichsweikamp
-
NEW: Show battery type in surface mode next to battery voltage2017-01-16, by heinrichsweikamp
-
no sensors in surface mode if the computer has no sensor inputs2017-01-16, by heinrichsweikamp
-
2.12 release candidate...2017-01-13, by heinrichsweikamp
-
Fix new battery menu on Power-on reset2017-01-04, by heinrichsweikamp
-
minor2016-12-20, by heinrichsweikamp
-
CHANGE: Show warnings either in Customview (If active) _or_ next to warning sign2016-12-18, by heinrichsweikamp
-
NEW: New Customview 11 in dive mode shows ppO2, EAD/END and CNS2016-12-11, by heinrichsweikamp
-
minor: clear screen while resetting settings2016-12-06, by heinrichsweikamp
-
minor2016-11-28, by heinrichsweikamp
-
minor2016-11-25, by heinrichsweikamp
-
battery gauge handling2016-11-20, by heinrichsweikamp
-
battery gauge handling2016-11-19, by heinrichsweikamp
-
BUGFIX: Minor layout corrections in imperial units dive screen2016-11-18, by heinrichsweikamp
-
CHANGE: Easier to understand "New Battery" menu (OSTC model dependent)2016-11-02, by heinrichsweikamp
-
minor cleanups2016-10-31, by heinrichsweikamp
-
CHANGE: Indicate "Bailout" for bailout deco plan in internal deco planer2016-10-28, by heinrichsweikamp
-
repeated init (For screen 2 issues)2016-10-10, by heinrichsweikamp
-
French/Italian release2016-10-10, by heinrichsweikamp
-
2.10 release2016-10-10, by heinrichsweikamp
-
show language version in information menu2016-09-28, by heinrichsweikamp
-
recover old battery status prior 2.092016-09-28, by heinrichsweikamp
-
2.1 stable work...2016-09-27, by heinrichsweikamp
-
NEW: Store more battery info into logbook memory2016-09-27, by heinrichsweikamp
-
minor: fix some alignments for OSTC cR2016-09-27, by heinrichsweikamp
-
NEW: Show Uptime (Time since last firmware boot) in information menu2016-09-19, by heinrichsweikamp
-
changelog2016-09-01, by heinrichsweikamp
-
speedup analog presses2016-09-01, by heinrichsweikamp
-
bugfix "old battery" type2016-08-31, by heinrichsweikamp
-
minor2016-08-31, by heinrichsweikamp
-
work on new battery options2016-08-30, by heinrichsweikamp
-
minor2016-08-29, by heinrichsweikamp
-
minor2016-08-19, by heinrichsweikamp
-
minor: Default timeout is 5min2016-08-18, by heinrichsweikamp
-
Adjustable timeout for Divemode (Config 0x48)2016-08-17, by heinrichsweikamp
-
minor2016-07-26, by heinrichsweikamp
-
doc update2016-07-26, by heinrichsweikamp
-
+BUGFIX: Compatibility with "hwOS Config" fixed2016-07-26, by heinrichsweikamp
-
docu update (hardware descriptor byte)2016-07-13, by heinrichsweikamp
-
docu update (hardware descriptor byte)2016-07-12, by heinrichsweikamp
-
2.09 beta start2016-07-06, by heinrichsweikamp
-
CHANGE: Language fixes, 2.08 release2016-06-30, by heinrichsweikamp
-
no screen reboot after logbook exit2016-06-24, by heinrichsweikamp
-
Logbook marker temporally disabled in internal logbook2016-06-23, by heinrichsweikamp
-
hunting a bug in the logbook (Day 3)2016-06-22, by heinrichsweikamp
-
minor2016-06-22, by heinrichsweikamp
-
hunting a bug in the logbook (Day 2)2016-06-22, by heinrichsweikamp
-
hunting a bug in the logbook...2016-06-21, by heinrichsweikamp
-
minor2016-06-21, by heinrichsweikamp
-
hardware_flag handling2016-06-16, by heinrichsweikamp
-
some cleanup2016-06-15, by heinrichsweikamp
-
add code for new compass chip2016-06-14, by heinrichsweikamp
-
docu update2016-06-10, by heinrichsweikamp
-
minor2016-05-13, by heinrichsweikamp
-
ignore 0x47 for standard hwOS2016-05-12, by heinrichsweikamp
-
_another_ timing fix for firmware updates (2.07 was not published yet anyway)2016-05-02, by heinrichsweikamp
-
2.07 release2016-04-29, by heinrichsweikamp
-
fix Page-Program timing2016-04-29, by heinrichsweikamp
-
fix handling for new flash memory chip2016-04-29, by heinrichsweikamp
-
CHANGE: Remove ppO2 [Dil] from OC dive mode screen2016-04-25, by heinrichsweikamp
-
some cleanup2016-04-19, by heinrichsweikamp
-
minor2016-04-18, by heinrichsweikamp
-
NEW: Support for new logbook memory chip (minor hardware change)2016-04-18, by heinrichsweikamp
-
minor2016-04-10, by heinrichsweikamp
-
support for new flash memory2016-03-29, by heinrichsweikamp
-
NEW: New Customview shows ppO2(O2) and ppO2(Diluent) during CCR mode2016-03-22, by heinrichsweikamp
-
2.04beta start2016-03-15, by heinrichsweikamp
-
BUGFIX: Fix missing ccr setup menu (From 2.02)2016-03-11, by heinrichsweikamp
-
BUGFIX: Fix rare issue after battery change (OSTC3 did not start properly)2016-03-08, by heinrichsweikamp
-
minor docu update2016-02-24, by heinrichsweikamp
-
2.01 release2016-02-02, by heinrichsweikamp
-
changelog2016-02-02, by heinrichsweikamp
-
Minor language updates2016-02-02, by heinrichsweikamp
-
BUGFIX: Divetime >99mins was not displayed (Only OSTC2 with serial >= )2016-02-01, by heinrichsweikamp
-
2.00 release2016-01-11, by heinrichsweikamp
-
NEW: "Lost Gas" feature allows disabling gases during the dive2016-01-10, by heinrichsweikamp
-
NEW: Logbook shows markers with small orange boxes in the profile2016-01-10, by heinrichsweikamp
-
Logbook marker can be set in dive mode menu (OC only)2016-01-09, by heinrichsweikamp
-
1.94beta release2015-12-10, by heinrichsweikamp
-
CHANGE: New segmented speed graph in divemode2015-11-24, by heinrichsweikamp
-
BUGFIX: Make sure SP1 is always selected on start in Auto-SP mode2015-11-23, by heinrichsweikamp
-
some documentation added2015-11-23, by heinrichsweikamp
-
place total dives backup counter in eeprom 16:172015-11-23, by heinrichsweikamp
-
1.93 release2015-11-16, by heinrichsweikamp
-
BUGFIX: minor text allignment in CCR mode2015-11-06, by heinrichsweikamp
-
tweak response timing in comm mode2015-11-05, by heinrichsweikamp
-
NEW: Show actual dive count in logbook list view (If <1000)2015-11-03, by heinrichsweikamp
-
add profile version to compact headers2015-11-02, by heinrichsweikamp
-
Fix text alignment for French version2015-10-28, by heinrichsweikamp
-
CHANGE: Logbook now shows end-of-dive date and time for dives made with firmware <1.92 indicated by an icon in the logbook2015-10-27, by heinrichsweikamp
-
BUGFIX: German texts in ppo2 menu were too long for screen resulting in resulting in text display issues2015-10-19, by heinrichsweikamp
-
1.90 release2015-10-09, by heinrichsweikamp
-
some cleanups, jump to 1.90 stable2015-10-07, by heinrichsweikamp
-
BUGFIX: +5min for stopwatch during simulation did not work2015-10-07, by heinrichsweikamp
-
minor language update (german)2015-10-06, by heinrichsweikamp
-
language updates2015-09-30, by heinrichsweikamp
-
allow compass bearing on surface2015-09-23, by heinrichsweikamp
-
BUGFIX: Battery consumption calculation in sleep mode (3,6V battery only)2015-09-19, by heinrichsweikamp
-
Merge2015-09-15, by heinrichsweikamp
-
minor2015-09-11, by heinrichsweikamp
-
BUGFIX: BLE timings for MAC issues2015-09-15, by heinrichsweikamp
-
set char_I_current_gas for gas6 use2015-09-10, by heinrichsweikamp
-
CHANGE: Do not show ppO2 in warning area if already shown in custom view2015-09-07, by heinrichsweikamp
-
docu update2015-08-25, by heinrichsweikamp
-
1.87 release2015-08-21, by heinrichsweikamp
-
logbook work2015-08-19, by heinrichsweikamp
-
fix some display issues with display12015-08-19, by heinrichsweikamp
-
debugging the compass screen2015-08-18, by heinrichsweikamp
-
fixing some layout issues2015-08-18, by heinrichsweikamp
-
Additional temperature calibration via PC interface2015-08-16, by heinrichsweikamp
-
jump to 1.872015-08-15, by heinrichsweikamp
-
tft timings2015-08-15, by heinrichsweikamp
-
minor2015-08-12, by heinrichsweikamp
-
french update2015-08-05, by heinrichsweikamp
-
cleanup2015-08-04, by heinrichsweikamp
-
changelog2015-08-04, by heinrichsweikamp
-
1.85beta release2015-08-04, by heinrichsweikamp
-
hardware support2015-08-03, by heinrichsweikamp
-
make AUTO SP available on OSTC2 hardware2015-08-03, by heinrichsweikamp
-
french update2015-08-03, by heinrichsweikamp
-
BUGFIX: Auto-Brightness clipped to lowest settings in bright sunlight on some devices2015-08-02, by heinrichsweikamp
-
Changed content for new 0x6F command (Get compact headers)2015-08-02, by heinrichsweikamp
-
hud v3 support2015-07-31, by heinrichsweikamp
-
some cleanups2015-07-29, by heinrichsweikamp
-
NEW: Quit Simulator automatically when starting a real dive2015-07-28, by heinrichsweikamp
-
add setpoint change to first sample in CCR mode2015-07-28, by heinrichsweikamp
-
some cleanups2015-07-23, by heinrichsweikamp
-
docu update2015-07-23, by heinrichsweikamp
-
[FIX] GasVolume: missing gas changes w/o stops.2015-07-15, by jDG
-
Changed content for new 0x6F command (Get compact headers)2015-07-22, by heinrichsweikamp
-
New option to download "Compact Headers". Improved BLE support (OSTC 2 and OSTC 3+), updated OSTC interface documentation2015-07-21, by heinrichsweikamp
-
re-arrange settings menu2015-07-20, by heinrichsweikamp
-
CHANGE: GF and aGF high range increased to 45-110%2015-07-20, by heinrichsweikamp
-
BUGFIX: Rotate button sensitivity with screen (OSTC 2 and cR)2015-07-20, by heinrichsweikamp
-
Fix low_depth shall be stored as a float (no rounding).2015-07-15, by jDG
-
Show ppo2 <1bar with leading zero2015-07-06, by heinrichsweikamp
-
changelog2015-07-03, by heinrichsweikamp
-
minor: fix calc_deko_divemode_sensor2015-07-03, by heinrichsweikamp
-
NEW: Mode Auto SP: Automatically switches the SP during descent (CC Mode)2015-07-03, by heinrichsweikamp
-
cleanup menu, add "Auto SP" option (Not working yet), minor layout change in compass menu2015-06-28, by heinrichsweikamp
-
Merged new_screen_layout into default2015-06-28, by Janos Kovacs
-
Always show ppO2 (warning position, standard color) option new_screen_layout2015-06-28, by janos_kovacs
-
Merged new_screen_layout into default2015-06-28, by Janos Kovacs
-
Extend the Ceiling custom-view with ppO2 and current GF new_screen_layout2015-06-28, by Janos Kovacs
-
Merged new_screen_layout into default2015-06-26, by Janos Kovacs
-
change button sensitivity range and default2015-06-21, by heinrichsweikamp
-
Fix: missing attention coloring for standard (static) ascend rate limit new_screen_layout2015-06-14, by janos_kovacs
-
VSIbar #4: VSI settings submenu, graph option, logbook offset and compass calib. menu exit fix new_screen_layout2015-06-13, by Janos Kovacs
-
FIX minor assert: separate diluant list means current gas can go up to 10.2015-06-12, by jDG
-
FIX 16bits CNS feedback: assert CNS up to 999%2015-06-12, by jDG
-
VSIbar #3d: more filter, neg_flag_velocity close to calculation, debug color for descend bar new_screen_layout2015-06-11, by janos_kovacs
-
FIX minor comment about deco offset unit...2015-06-10, by jDG
-
Config table for alternative display2015-06-09, by heinrichsweikamp
-
FIX missing extern .C definition.2015-06-09, by jdg
-
VSIbar #2: ascend bar + max-depth title alignment. Debug: bar-frame, zero-line, sim+- 0.1m new_screen_layout2015-06-07, by janos_kovacs
-
VSI text v2 merged from new_screen_layout into default2015-06-05, by Janos Kovacs
-
Merge default back to the new_screen_layout development branch new_screen_layout2015-06-02, by Janos Kovacs
-
rename tMODwarning2015-06-02, by heinrichsweikamp
-
Merge with new_screen_layout2015-06-01, by heinrichsweikamp
-
Add configuration option to control depth warning blinking new_screen_layout2015-06-01, by janos_kovacs
-
default branch2015-06-01, by heinrichsweikamp
-
Merged Screen layout mod #1 into Screen layout work #32015-05-31, by Janos Kovacs
-
Make char_I_bottom_usage and char_I_deco_usage configurable from PC2015-05-31, by heinrichsweikamp
-
new submenu for gas consumption, show actual mix instead of GAS1-GAS5 in deco planner2015-05-31, by heinrichsweikamp
-
German tGasUsage2015-05-31, by heinrichsweikamp
-
Slight more efficient bail deco, Test with 2 bail tanks.2015-05-31, by jDG
-
NEW CCR decoplan: 2nd pass to display bailout stops and gas volumes2015-05-31, by jDG
-
FIX clear before displaying gas volumes.2015-05-30, by jDG
-
FIX tests to use plans copyed from actual OSTC3 1.82 computer.2015-05-30, by jDG
-
ADD (back) Gas Volumes display after decoplanning.2015-05-30, by jDG
-
ADD tGasUsage, with FR translation (and DE,IT defaults)2015-05-30, by jDG
-
NEW gas_volume unit test in CCR mode. Works too.2015-05-29, by jdg
-
[mq]: 2015-05-29_02-40-44_r288+.diff2015-05-29, by jdg
-
FIX gas_volume shall read gas switches from char_O_deco_gas2015-05-29, by jdg
-
FIX gas_volumes: shall take stops in forward order.2015-05-29, by jdg
-
NEW test w/o stops and with stops2015-05-29, by jdg
-
NEW unit tests for gas volumes...2015-05-28, by jdg
-
preperations to compute gas consumtion in simulator2015-05-28, by heinrichsweikamp
-
1.82beta with new compass calib code2015-05-27, by heinrichsweikamp
-
Make a more compact COMPASS calibration code (<7KB), and add more tests.2015-05-22, by jDG
-
BUGFIX: Fix download issue for dives made with 1.80 firmware2015-05-26, by heinrichsweikamp
-
doku update2015-05-26, by heinrichsweikamp
-
bugfix wrong profile length in header2015-05-26, by heinrichsweikamp
-
BUGFIX: There was a 1:4096 chance that a portion of a dive was not stored correctly resulting in download issues2015-05-18, by heinrichsweikamp
-
1.79beta - update internal sensor registers during boot2015-05-18, by heinrichsweikamp
-
Increase byte timeout in PC download mode, faster response to "Exit" in main menu2015-05-12, by heinrichsweikamp
-
rename into hwOS2015-05-07, by heinrichsweikamp
-
BUGFIX: Fast Gas change near the ppO2 limit could cause switching to a non-available Gas #02015-05-05, by heinrichsweikamp
-
CHANGE: Automatically abort connection fail after 2mins (Bluetooth only)2015-05-04, by heinrichsweikamp
-
1.78 release2015-04-29, by heinrichsweikamp
-
Update digital ppO2 data automatically2015-04-28, by heinrichsweikamp
-
increase min input voltage from 1,2mV to 1,9mV (cR only)2015-04-22, by heinrichsweikamp
-
adjust menu for different hardware versions2015-04-20, by heinrichsweikamp
-
BUGFIX: Increase timing tolerance for S8 HUD (cR only)2015-04-19, by heinrichsweikamp
-
BUGFIX: Analog sensors were ignored in 1.762015-04-16, by heinrichsweikamp
-
Charge done indicator (cR and 2 Hardware)2015-04-14, by heinrichsweikamp
-
1.76 release2015-03-30, by heinrichsweikamp
-
Fix compass ruler's missing bottom ticks; Clear between the bearing marker lines and draw a dot.2015-03-26, by janos_kovacs
-
show unit8 options in menu left-aligned2015-03-26, by heinrichsweikamp
-
bugfix dynamic gas list2015-03-26, by heinrichsweikamp
-
language update2015-03-25, by heinrichsweikamp
-
increase immunity against false Qi data2015-03-24, by heinrichsweikamp
-
minor cleanup2015-03-23, by heinrichsweikamp
-
patch for bearing issue2015-03-23, by heinrichsweikamp
-
minor speed and size improvements for the compass routine2015-03-23, by heinrichsweikamp
-
place compass display code into compass_ops.asm2015-03-23, by heinrichsweikamp
-
add bearing option to compass2015-03-23, by heinrichsweikamp
-
preparations to set a course for the compass display2015-03-20, by heinrichsweikamp
-
another icon update2015-03-19, by heinrichsweikamp
-
change warning sign2015-03-19, by heinrichsweikamp
-
some cleanup, temporaly disable dive_warning.inc2015-03-18, by heinrichsweikamp
-
Graphical compass from kovacs2015-03-18, by heinrichsweikamp
-
ignore sensor for non-sensor hardware2015-03-17, by heinrichsweikamp
-
support hardware_flag for all possible hardware combinations2015-03-16, by heinrichsweikamp
-
BUGFIX: Always update CCR sensor data in Sensor-Menu2015-03-13, by heinrichsweikamp
-
minor docu update2015-03-05, by heinrichsweikamp
-
use single-byte hardware flag (again)2015-03-04, by heinrichsweikamp
-
minor docu update (removed typo)2015-03-04, by heinrichsweikamp
-
auto-select correct settings menu2015-03-04, by heinrichsweikamp
-
expand hardware_flag to 4 bytes2015-03-03, by heinrichsweikamp
-
docu update2015-03-02, by heinrichsweikamp
-
auto-select correct ccr menu2015-03-02, by heinrichsweikamp
-
CNANGE: aGF pair has same range then normal GF pair2015-03-01, by heinrichsweikamp
-
cleanup2015-03-01, by heinrichsweikamp
-
1.75 release2015-02-26, by heinrichsweikamp
-
configure hardware_flag byte2015-02-25, by heinrichsweikamp
-
under construction: new hardware_flag to configure different hardware versions2015-02-25, by heinrichsweikamp
-
Show OSTC2-like active gas boxes in surface mode2015-02-25, by heinrichsweikamp
-
show start gas in normal font2015-02-25, by heinrichsweikamp
-
show start gas in OC mode permanently2015-02-22, by mh
-
BUGFIX: Show average depth with one decimal digit only2015-02-21, by mh
-
Bugfix: Check for divemode before checking for menu2015-02-19, by mh
-
minor cleanup2015-02-18, by mh
-
1.74 release2015-02-05, by heinrichsweikamp
-
NEW: Support for hwHUD without the LED module2015-02-02, by heinrichsweikamp
-
button config (cR)2015-02-02, by heinrichsweikamp
-
BUGFIX: Show dives with >999mins divetime correctly2015-02-01, by heinrichsweikamp
-
temporally disable "Copy disable flags from digital input" routine2015-01-29, by heinrichsweikamp
-
PC config, 1.72 release2015-01-14, by heinrichsweikamp
-
check opt_max correctly2015-01-06, by heinrichsweikamp
-
minor: configure buttons during splash screen2015-01-05, by heinrichsweikamp
-
make button sensitivity configurable (cR hardware)2015-01-05, by heinrichsweikamp
-
init new 4kB Page in logbook memory when pointer is not valid.2015-01-04, by heinrichsweikamp
-
1.71beta start2014-12-19, by heinrichsweikamp
-
1.7 release2014-12-17, by heinrichsweikamp
-
NEW: On-board simulator can increase divetime in 5min steps2014-12-15, by heinrichsweikamp
-
ignore battery menu for cr2014-12-15, by heinrichsweikamp
-
compass changes2014-12-14, by heinrichsweikamp
-
layout changes2014-12-13, by heinrichsweikamp
-
Merge2014-12-10, by heinrichsweikamp
-
minor2014-12-10, by heinrichsweikamp
-
do not clear char_O_deco_gas in copy_deco_table2014-12-07, by heinrichsweikamp
-
cleanup2014-12-07, by heinrichsweikamp
-
NEW: Show plan parameters in decoplan result page2014-12-07, by heinrichsweikamp
-
charge indicator on surface screen2014-12-06, by heinrichsweikamp
-
always reboot display in divemode2014-12-01, by heinrichsweikamp
-
Preparations for 1.72014-11-26, by heinrichsweikamp
-
minor2014-11-23, by heinrichsweikamp
-
1.64 (Fix ambient light for cR)2014-11-21, by heinrichsweikamp
-
1.63beta release2014-11-21, by heinrichsweikamp
-
lower minimum backlight in eco mode2014-11-20, by heinrichsweikamp
-
cleanup2014-11-12, by heinrichsweikamp
-
minor2014-11-11, by heinrichsweikamp
-
(Slightly) reduce current consumption in Eco and sleep mode2014-11-10, by heinrichsweikamp
-
cleanup2014-11-06, by heinrichsweikamp
-
suppress ghost readings for long, open cables2014-11-06, by heinrichsweikamp
-
allow auto-return from setpoint fallback2014-11-05, by heinrichsweikamp
-
1.62beta start2014-11-04, by heinrichsweikamp
-
reset voting logic on sensor switch2014-11-03, by heinrichsweikamp
-
voting logic for external monitoring2014-11-03, by heinrichsweikamp
-
minor2014-10-30, by heinrichsweikamp
-
limit sensor-read ppO2 to 2.55bar2014-10-29, by heinrichsweikamp
-
ignore un-calibrated sensors even if they become valid2014-10-29, by heinrichsweikamp
-
NEW: Show Bailout Gas List in Surface mode (CCR Modes)2014-10-27, by heinrichsweikamp
-
CHANGE: Longer timeout (4 min) for calibration menu2014-10-25, by heinrichsweikamp
-
minor2014-10-22, by heinrichsweikamp
-
BUGFIX: Check min and max values after PC configuration properly2014-10-18, by heinrichsweikamp
-
BUGFIX: Quit Apnea mode on the surface manually2014-10-17, by heinrichsweikamp
-
BUGFIX: O2 > 99% was not configurable from the PC2014-10-16, by heinrichsweikamp
-
minor cleanup2014-10-10, by heinrichsweikamp
-
BUGFIX: END/EAD updated when adjusting current gas during the dive2014-10-09, by heinrichsweikamp
-
1.60 work...2014-10-08, by heinrichsweikamp
-
1.54 beta start2014-10-07, by heinrichsweikamp
-
BUGFIX: Average depth computation2014-10-07, by heinrichsweikamp
-
Merge2014-10-07, by heinrichsweikamp
-
surface pressure copy in simulator2014-10-06, by heinrichsweikamp
-
CHANGE: Draw a frame around the dive mode menu2014-10-06, by heinrichsweikamp
-
CHANGE: Clarify Travel Gases with "---" as change depth2014-10-05, by heinrichsweikamp
-
minor2014-10-01, by heinrichsweikamp
-
BUGFIX: Future TTS in sensor mode2014-09-30, by heinrichsweikamp
-
1.54 beta start2014-09-30, by heinrichsweikamp
-
CHANGE: Compass readout smoothed2014-09-30, by heinrichsweikamp
-
CHANGE: Improve internal logbook usability2014-09-29, by heinrichsweikamp
-
BUGFIX: False max. temp in Logbook, false Bailout and Gas 6 flags in logbook2014-09-29, by heinrichsweikamp
-
logbook2014-09-28, by heinrichsweikamp
-
BUGFIX: Flip compass with flipped screen, too2014-09-28, by heinrichsweikamp
-
testing consumption2014-09-11, by heinrichsweikamp
-
1.52 beta release - 1.53 beta start2014-09-10, by heinrichsweikamp
-
clarify diluent change in the documentation2014-09-10, by heinrichsweikamp
-
NEW: Safe tissue data, date and time during firmware update2014-09-09, by heinrichsweikamp
-
skip fallback warning in OC modes2014-09-09, by heinrichsweikamp
-
BUGFIX: Fast diluent (w/o dive mode menu) change did not work correctly2014-09-08, by heinrichsweikamp
-
1.51 beta release - 1.52 beta start2014-09-08, by heinrichsweikamp
-
nicer boot into surfacemode2014-09-04, by heinrichsweikamp
-
make new parameters configurable through pc2014-08-29, by heinrichsweikamp
-
minor2014-08-28, by heinrichsweikamp
-
CHANGE: Re-arranged Settings Menu, add 180? rotate to menu2014-08-28, by heinrichsweikamp
-
NEW: Show ppO2 for change depth during gas setup2014-08-27, by heinrichsweikamp
-
minor2014-08-21, by heinrichsweikamp
-
BUGFIX: Clear Setpoint-Fallback warning when in bailout2014-08-21, by heinrichsweikamp
-
work on flip screen...2014-08-18, by heinrichsweikamp
-
1.51beta start2014-08-13, by heinrichsweikamp
-
1.50 stable release2014-08-11, by heinrichsweikamp
-
some cleanup2014-08-06, by heinrichsweikamp
-
some cleanup2014-08-06, by heinrichsweikamp
-
fallback default = 12014-08-05, by heinrichsweikamp
-
NEW: Setpoint-Fallback option for external O2 sensor failure2014-08-05, by heinrichsweikamp
-
1.45 beta release2014-08-04, by heinrichsweikamp
-
seperate option table, place in address <0x100002014-08-03, by heinrichsweikamp
-
option_read and option_write eeprom banking2014-07-31, by mh
-
New changelog.txt format2014-07-31, by heinrichsweikamp
-
1.44 beta release2014-07-18, by heinrichsweikamp
-
some cleanup2014-07-17, by heinrichsweikamp
-
minor: some extra protection against wrong gas selection2014-07-17, by heinrichsweikamp
-
Simplify gas change2014-07-17, by heinrichsweikamp
-
rename Deco Planner to Simulator2014-07-17, by heinrichsweikamp
-
minor2014-07-16, by heinrichsweikamp
-
Show clock in Apnea mode, minor layout changes in Apnea mode2014-07-15, by heinrichsweikamp
-
BUGFIX: Surface interval was not displayed correctly in some cases2014-07-14, by heinrichsweikamp
-
Bugfix: Start dive mode simulator in correct depth2014-07-08, by heinrichsweikamp
-
NEW: Update warnings every second2014-07-04, by heinrichsweikamp
-
no safety stop during menu display2014-07-03, by heinrichsweikamp
-
minor cleanup2014-07-03, by heinrichsweikamp
-
catch timeout during set time/date command2014-07-01, by heinrichsweikamp
-
1.41beta release2014-07-01, by heinrichsweikamp
-
fix depth<0m display, ceiling2014-06-30, by heinrichsweikamp
-
minor2014-06-29, by heinrichsweikamp
-
cleanup2014-06-29, by heinrichsweikamp
-
add ceiling display2014-06-29, by heinrichsweikamp
-
Show %'s for non-GF deco model in surface mode2014-06-27, by heinrichsweikamp
-
minor2014-06-27, by heinrichsweikamp
-
battery check in sleep2014-06-27, by heinrichsweikamp
-
Do not show "GF info" for non-GF modes2014-06-27, by heinrichsweikamp
-
show heading with leading zeros2014-06-27, by heinrichsweikamp
-
minor2014-06-25, by heinrichsweikamp
-
show decomode in logbook and simulator w/o sensor type2014-06-23, by heinrichsweikamp
-
FIX: Gas volume computation when using several travel mix.2014-06-23, by heinrichsweikamp
-
minor fix: assert should pass for pure helium diluant2014-06-23, by heinrichsweikamp
-
Merge2014-06-23, by heinrichsweikamp
-
1.40 release2014-06-17, by heinrichsweikamp
-
Bugfix: CNS in planner2014-06-17, by heinrichsweikamp
-
BUGFIX: OSTC settings via USB issues2014-06-10, by heinrichsweikamp
-
Merge2014-06-05, by heinrichsweikamp
-
language updates2014-06-04, by heinrichsweikamp
-
BUGFIX: wrong ppo2 recording parameter in short header2014-06-05, by heinrichsweikamp
-
minor2014-06-03, by heinrichsweikamp
-
Show HUD voltages only in CCR mode...2014-06-03, by heinrichsweikamp
-
Show a Safety Stop if enabled (Menu "Deco Parameters")2014-06-03, by heinrichsweikamp
-
Minor language updates2014-06-02, by heinrichsweikamp
-
NEW: Show End-of-Dive time together with clock during deco2014-05-07, by heinrichsweikamp
-
increase ir-timeout to 4 seconds2014-05-04, by heinrichsweikamp
-
1.30 release2014-05-02, by heinrichsweikamp
-
show event "bailout" in the internal logbook2014-05-02, by heinrichsweikamp
-
add event "bailout" in profile2014-05-01, by heinrichsweikamp
-
CHANGE: Always compute bailout plan based on all active gases2014-04-28, by heinrichsweikamp
-
auto-reset compass filtering data before calibration2014-04-28, by heinrichsweikamp
-
BUGFIX: Show "*" always in front of the initial Setpoint 12014-04-28, by heinrichsweikamp
-
BUGFIX: compass calibration does now timeout automatically after 60s2014-04-22, by heinrichsweikamp
-
clear pressure sensor compensation upon update2014-04-17, by heinrichsweikamp
-
add sensor calibration option (PC only), some cleanup2014-04-16, by heinrichsweikamp
-
minor, always re-init compass in calibration loop2014-04-15, by heinrichsweikamp
-
NEW: automatic compass gain makes calibration quicker2014-04-15, by heinrichsweikamp
-
BUGFIX: No average depth for end-of-dive portion (<1m)2014-04-15, by heinrichsweikamp
-
fix minor display bug (battery percent)2014-04-14, by heinrichsweikamp
-
CHANGE: Color schemes improved2014-04-02, by heinrichsweikamp
-
CHANGE: No warning sign for selected aGF2014-04-02, by heinrichsweikamp
-
No graphical output (yet)2014-03-31, by heinrichsweikamp
-
Minor french update2014-03-31, by heinrichsweikamp
-
Test with graphic compass2014-03-17, by heinrichsweikamp
-
1.23 release2014-03-10, by heinrichsweikamp
-
new commands in download mode:2014-02-27, by mh
-
new command in download mode: "r" - read setting2014-02-27, by mh
-
BUGFIX: Reset Logbook did not reset Logbook TOC properly2014-02-26, by mh
-
BUGFIX: Potential bug to freeze the OSTC3 after battery change or update2014-02-20, by heinrichsweikamp
-
1.21 release2014-02-19, by heinrichsweikamp
-
change log2014-02-11, by heinrichsweikamp
-
1.2RC2014-02-10, by heinrichsweikamp
-
Merge with ClaudeDive_Translations2014-02-10, by heinrichsweikamp
-
1.13 beta start2014-02-04, by heinrichsweikamp
-
+CHANGE: Some French Translations2014-02-02, by heinrichsweikamp
-
BUGFIX: Set Day for months <31 days2014-02-01, by heinrichsweikamp
-
second debug mode page2014-01-11, by heinrichsweikamp
-
BUGFIX: Maintain last selected customview in surface mode2014-01-11, by heinrichsweikamp
-
change log2014-01-10, by heinrichsweikamp
-
Merge2014-01-10, by heinrichsweikamp
-
allow logbook erase from reset menu2013-12-19, by heinrichsweikamp
-
show battery voltage in info menu2014-01-10, by heinrichsweikamp
-
1.1 release2013-12-04, by heinrichsweikamp
-
BUGFIX: Display Desat.-Time >100 hours2013-12-03, by heinrichsweikamp
-
Backlight level in eco mode2013-12-01, by heinrichsweikamp
-
startup with 1.6 hardware2013-11-20, by heinrichsweikamp
-
minor2013-10-02, by heinrichsweikamp
-
another small French update2013-10-02, by heinrichsweikamp
-
Change "O2" warning to "ppO2"2013-09-29, by heinrichsweikamp
-
some cleanup/changelog2013-09-29, by heinrichsweikamp
-
NEW: Dynamic Gaslist in OC mode (Divemode, Customview 7)2013-09-29, by heinrichsweikamp
-
english correction2013-09-29, by heinrichsweikamp
-
language updates2013-09-28, by heinrichsweikamp
-
NEW: user-selectable color schemes2013-09-27, by heinrichsweikamp
-
minor german update2013-09-27, by heinrichsweikamp
-
Time and Date in normal (Not tiny) font2013-09-23, by heinrichsweikamp
-
1.02 beta start2013-09-04, by heinrichsweikamp
-
Bugfix: deco gas init in OC planner2013-09-04, by heinrichsweikamp
-
1.01 beta start2013-08-28, by heinrichsweikamp
-
BUGFIX: Percent display with 1,5V batteries2013-08-28, by heinrichsweikamp
-
.99 release2013-08-16, by heinrichsweikamp
-
minor2013-08-15, by mh
-
Surface customview with important deco settings2013-08-15, by mh
-
Bugfix: Simulator in CC mode2013-08-15, by mh
-
remember last customview in dive and surface mode2013-08-15, by mh
-
Show total divetime in apnea mode2013-08-15, by mh
-
use four additional data points for the battery monitor2013-08-15, by mh
-
changelog2013-08-04, by heinrichsweikamp
-
change apnea timeout, do no longer store apnea dives in logbook2013-08-04, by heinrichsweikamp
-
small cleanup2013-08-04, by heinrichsweikamp
-
Bugfix: NOAA tables for CNS are in ATA, not bar2013-08-04, by heinrichsweikamp
-
GF high lowest setting 60%2013-07-22, by heinrichsweikamp
-
BUGFIX: alternating brightness at very low ambient light2013-07-21, by heinrichsweikamp
-
minor2013-07-21, by heinrichsweikamp
-
adding cardinal (and ordinal) directions for the compass2013-07-20, by heinrichsweikamp
-
rx isr2013-07-20, by heinrichsweikamp
-
logo update2013-07-17, by heinrichsweikamp
-
0.97 release2013-07-09, by heinrichsweikamp
-
fix imperial units in logbook2013-07-09, by heinrichsweikamp
-
save logbook recording interval2013-07-08, by heinrichsweikamp
-
new option to switch samplingrate between 10s and 2s2013-07-08, by heinrichsweikamp
-
change gf_low default to 30%2013-07-08, by heinrichsweikamp
-
Reset options to default if they are not within the allowed min/max values2013-07-04, by heinrichsweikamp
-
minor cleanup2013-07-03, by heinrichsweikamp
-
changelog2013-07-03, by heinrichsweikamp
-
add new opt_compass_gain option to work with more magnetic battery types2013-07-03, by heinrichsweikamp
-
0.96 release2013-06-24, by heinrichsweikamp
-
calm compass reading for minor heading changes2013-06-16, by heinrichsweikamp
-
reduce eco low brightness threshold (for cave diving)2013-06-12, by heinrichsweikamp
-
Show "MOD:" instead of "EAD:" in gas setup2013-06-11, by heinrichsweikamp
-
fix negative temperature display in surfacemode2013-05-30, by heinrichsweikamp
-
logo update2013-05-26, by heinrichsweikamp
-
Show Max. Depth with 0.1m precision2013-05-26, by heinrichsweikamp
-
sensor status on power-on reset2013-05-16, by heinrichsweikamp
-
Timeout in decoplanner result page2013-05-15, by heinrichsweikamp
-
italian update2013-05-14, by heinrichsweikamp
-
fix custom text <60 chars2013-05-14, by heinrichsweikamp
-
bugfix: dive length in normal header2013-05-10, by heinrichsweikamp
-
Put logbook offset into dive header2013-05-10, by heinrichsweikamp
-
add changelog2013-05-10, by heinrichsweikamp
-
interface description added2013-05-06, by heinrichsweikamp
-
battery warning levels, max. brightnes setting2013-05-05, by heinrichsweikamp
-
init22013-04-24, by heinrichsweikamp
-
init2013-04-24, by heinrichsweikamp