;=============================================================================
;
;   File hwos.asm														V2.99g
;
;   Definition of the hwOS dive computer platform.
;
;   Copyright (c) 2011, JD Gascuel, HeinrichsWeikamp, all right reserved.
;=============================================================================
; HISTORY
;   2011-05-24 : [jDG] Cleanups from initial Matthias code
;   2011-06-24 : [MH]  Added clock speeds


#include "hwos.inc"

;=============================================================================
;----------------------------- CONFIG ---------------------------------
	CONFIG	RETEN = OFF			; disabled - controlled by SRETEN bit
	CONFIG	SOSCSEL = HIGH		; High Power SOSC circuit selected
	CONFIG	XINST = OFF			; code won't execute in extended mode
	CONFIG	FOSC = INTIO2		; internal RC oscillator, no clock-out
	CONFIG	PLLCFG = OFF
	CONFIG	IESO = OFF			; disabled
	CONFIG	PWRTEN = OFF		; disabled, because incompatible with ICD3 (Ri-400)
	CONFIG	BOREN = ON			; controlled with SBOREN bit
	CONFIG	BORV = 2			; 2.0V
	CONFIG	BORPWR = MEDIUM		; BORMV set to medium power level
	CONFIG	WDTEN = ON			; WDT controlled by SWDTEN bit setting
	CONFIG	WDTPS = 128			; 1:128
	CONFIG	RTCOSC = SOSCREF	; RTCC uses SOSC
	CONFIG	MCLRE = ON			; MCLR Enabled, RG5 Disabled
	CONFIG	CCP2MX = PORTBE		; RE7-microcontroller mode/RB3-all other modes

hwos		CODE

;=============================================================================

	global	init_ostc
init_ostc:
; init oscillator
	banksel	common				; bank 1
	movlw	b'01110010'
	movwf	OSCCON				; 16 MHz INTOSC
	movlw	b'00001000'
	movwf	OSCCON2				; secondary oscillator running
	movlw	b'00000000'
	movwf	OSCTUNE				; 4x PLL disable (Bit 6) - only works with 8 or 16MHz (=32 or 64MHz)

	movlw	d'2'					; coding for speed normal
	movff	WREG,cpu_speed_request	; CPU shall run with normal speed
	movff	WREG,cpu_speed_state	; CPU does  run with normal speed

;	bcf		RCON,SBOREN			; brown-out off (Not needed, set in bootloader)
	bcf		RCON,IPEN			; priority interrupts off

	banksel	WDTCON
	movlw	b'10000000'
	movwf	WDTCON				; setup watchdog


; I/O Ports
	banksel	0xF16				; addresses, F16h through F5Fh, are also used by SFRs, but are not part of the access RAM

	clrf	REFOCON				; no reference oscillator active on REFO pin
	clrf	ODCON1				; disable open drain capability
	clrf	ODCON2				; disable open drain capability
	clrf	ODCON3				; disable open drain capability
	clrf	CM1CON				; disable
	clrf	CM2CON				; disable
	clrf	CM3CON				; disable

	movlw	b'11000000'			; ANSEL, AN7 and AN6 -> Analog inputs, PORTA is digital
	movwf	ANCON0
	movlw	b'00000111'			; ANSEL, AN8, AN9, AN10 -> Analog input
	movwf	ANCON1
	movlw	b'00000010'			; ANSEL, AN17 -> Analog input
	movwf	ANCON2

	banksel	common

;	movlw	b'00000000'			; 1= input -> Data TFT_high
	clrf	TRISA
;	movlw	b'00000000'			; init port
	clrf	PORTA

	movlw	b'00000011'			; 1= input, (RB0, RB1) -> switches, RB2 -> Power_MCP, RB3 -> s8_npower, RB4 -> LED_green/rx_nreset, RB5 -> /TFT_POWER
	movwf	TRISB
	movlw	b'00111000'			; init port, rx_nreset=1 -> hard reset RX
	movwf	PORTB

	movlw	b'10011010'			; 1= input, (RC0, RC1) -> SOSC, RC2 -> TFT_LED_PWM, (RC3,RC4) -> I²C, RC5 -> MOSI_MS5541, (RC6, RC7) -> UART1
	movwf	TRISC
;	movlw	b'00000000'			; init port
	clrf	PORTC

	movlw	b'00100000'			; 1= input, RD0 -> TFT_NCS, RD1 -> TFT_RS, RD2 -> TFT_NWR, RD3 -> TFT_RD, RD4 -> MOSI_Flash, RD5 -> MISO_Flash, RD6 -> CLK_Flash, RD7 -> TFT_NRESET
	movwf	TRISD
;	movlw	b'00000000'			; init port
	clrf	PORTD

;	movlw	b'00000000'			; 1= input, RE1 -> Power_IR, RE2 -> CS_MCP, RE3 -> LED_blue, RE4 -> power_sw1, RE5 -> Set to 1 for cR hardware
	clrf	TRISE
	movlw	b'00110001'			; init port
	movwf	PORTE

	movlw	b'01111110'			; 1= input, (RF1, RF2, RF3, RF4, RF5) -> Analog
	movwf	TRISF
;	movlw	b'00000000'			; init port
	clrf	PORTF

	movlw	b'00001110'			; 1= input, <7:6> not implemented, RG0 -> TX3_PIEZO_CFG, RG2 -> RX2, RG3 -> AN17_RSSI, RG4 -> SOSC_OUT, RG5 -> /RESET
	movwf	TRISG
	movlw	b'00000001'			; init port
	movwf	PORTG

;	movlw	b'00000000'			; 1= input -> Data TFT_low
	clrf	TRISH
;	movlw	b'00000000'			; init port
	clrf	PORTH

	movlw	b'10011011'			; 1= input, RJ4 -> vusb_in, RJ5 -> power_sw2,  RJ6 -> CLK_MS5541, RJ7 -> MISO_MS5541
	movwf	TRISJ
	movlw	b'00100000'			; init port
	movwf	PORTJ

; disable Charger by default
	bsf        charge_disable	    ; set      charging-inhibit signal
	bcf        TRISE,2
	
; Timer 0
	movlw	b'00000001'			; timer0 with 1:4 prescaler
	movwf	T0CON

; Timer 1 - Button hold-down timer
	movlw	b'10001100'			; 32768Hz clock source, 1:1 prescaler -> ; 30.51757813 µs/bit in TMR1L:TMR1H
	movwf	T1CON

; RTCC
	banksel 0xF16				; Addresses, F16h through F5Fh, are also used by SFRs, but are not part of the Access RAM.
	movlw 	0x55
	movwf 	EECON2
	movlw 	0xAA
	movwf 	EECON2
	bsf 	RTCCFG,RTCWREN		; Unlock sequence for RTCWREN
	bsf		RTCCFG,RTCPTR1
	bsf		RTCCFG,RTCPTR0
	bsf		RTCCFG,RTCEN		; Module enable
	bsf		RTCCFG,RTCOE		; Output enable
	movlw	b'00000100'			; 32768Hz SOCS on RTCC pin (PORTG,4) Bit7-5: Pullups for Port D, E and J
	movwf	PADCFG1
	movlw	b'11000100'
	movwf	ALRMCFG				; 1 second alarm
	movlw	d'1'
	movwf	ALRMRPT				; Alarm repeat counter
	movlw 	0x55
	movwf 	EECON2
	movlw 	0xAA
	movwf 	EECON2
	bcf 	RTCCFG,RTCWREN		; Lock sequence for RTCWREN
	banksel common

; A/D Converter
	movlw	b'00011000'			; power off ADC, select AN6
	movwf	ADCON0
	movlw	b'00100000'			; 2.048V Vref+
	movwf	ADCON1
	movlw	b'10001101'			; right aligned
	movwf	ADCON2

; init serial port1 (TRISC6/7)
	movlw	b'00001000'			; BRG16=1
	movwf	BAUDCON1
	movlw	.34					; SPBRGH:SPBRG = .34  : 114285 BAUD @ 16MHz (+0.79% Error to 115200 BAUD)
	movwf	SPBRG1				; SPBRGH:SPBRG = .207 :  19230 BAUD @ 16MHz (-0.16% Error to  19200 BAUD)
	clrf	SPBRGH1				;

	clrf	RCSTA1
	clrf	TXSTA1				; UART disable
	bcf		PORTC,6				; TX hard to GND

; init serial port2 (TRISG2)
	banksel	BAUDCON2
	movlw	b'00100000'			; BRG16=0		; inverted for IR
	movwf	BAUDCON2
	movlw	b'00100000'			; BRGH=0, SYNC=0
	movwf	TXSTA2
	movlw	.102				; SPBRGH:SPBRG = .102  : 2403 BAUD @ 16MHz
	movwf	SPBRG2
	clrf	SPBRGH2
	movlw	b'10010000'
	movwf	RCSTA2
	banksel	common

; Timer3 for IR-RX Timeout
	clrf	T3GCON				; reset Timer3 gate control register
	movlw	b'10001001'			; 1:1 prescaler -> 2 seconds@32768Hz, synced
; 30,51757813µs/bit in TMR3L:TMR3H
	movwf	T3CON

; SPI Module(s)
; SPI2: External Flash
	movlw	b'00110000'
	movwf	SSP2CON1
;	movlw	b'00000000'
	clrf	SSP2STAT
; ->0,25MHz Bit clock  @1MHz mode (Eco)
; ->  4MHz  Bit clock @16MHz mode (Normal)
; -> 16MHz  Bit clock @64MHz mode (Fastest)

; MSSP1 Module: I2C Master
	movlw	b'00101000'			; I2C master mode
	movwf	SSP1CON1
;	movlw	b'00000000'
	clrf	SSP1CON2
	movlw	0x27
	movwf	SSP1ADD				; 100kHz @ 16MHz Fosc

; PWM Module(s)
; PWM1 for LED dimming
	movlw	b'00001100'
	movwf	CCP1CON
	movlw	b'00000001'
	movwf	PSTR1CON			; pulse steering disabled
	movlw	d'255'
	movwf	PR2					; period
	; 255 is max brightness (300 mW)
	clrf	CCPR1L				; duty cycle
	clrf	CCPR1H				; duty cycle
	movlw	T2CON_NORMAL
	movwf	T2CON

; Timer5 for ISR-independent wait routines
	clrf	T5GCON				; reset Timer5 gate control register
	movlw	b'10001001'			; 1:1 prescaler -> 2 seconds@32768Hz, synced
; 30,51757813µs/bit in TMR5L:TMR5H
	movwf	T5CON

; Timer7 for 62,5ms Interrupt (Sensor states)
	banksel 0xF16				; addresses, F16h through F5Fh, are also used by SFRs, but are not part of the access RAM
	clrf	T7GCON				; reset Timer7 gate control register
	movlw	b'10001001'			; 1:1 prescaler -> 2 seconds@32768Hz, synced
	movwf	T7CON
	clrf	TMR7L
	movlw	.248
	movwf	TMR7H				; -> Rollover after 2048 cycles -> 62,5ms

; Turn off unused timer
	movlw	b'11000000'
	movwf	PMD0
	movlw	b'11010001'
	movwf	PMD1
	movlw	b'11010111'
	movwf	PMD2
	movlw	b'11111111'
	movwf	PMD3

; CTMU
	clrf	CTMUCONH
	clrf	CTMUCONL
	clrf	CTMUICON
	banksel	common

; Interrupts
	movlw	b'11010000'
	movwf	INTCON
	movlw	b'00001000'			; BIT7=1: pullup for PORTB disabled
	movwf	INTCON2
	movlw	b'00000000'
	movwf	INTCON3
	movlw	b'00000001'			; Bit0: TMR1
	movwf	PIE1
	movlw	b'00000010'			; Bit1: TMR3
	movwf	PIE2
	movlw	b'00000000'			; Bit1: TMR5
	movwf	PIE5
	movlw	b'00100001'			; Bit0: RTCC, Bit5: UART2
	movwf	PIE3
	movlw	b'00001000'			; Bit3: TMR7
	movwf	PIE5

	bsf		power_sw1
	btfss	power_sw1
	bra		$-4
	bsf		power_sw2
	btfss	power_sw2
	bra		$-4

	bcf		active_reset_ostc_rx	; start RX from RESET

	return

;=============================================================================
	global	speed_eco
speed_eco:
	movlw	d'1'
	movff	WREG,cpu_speed_request	; bank-independent
	; Done in ISR
	return
;=============================================================================
	global	speed_normal
speed_normal:
	movlw	d'2'
	movff	WREG,cpu_speed_request	; bank-independent
	; Done in ISR
	return
;=============================================================================
	global	speed_fastest
speed_fastest:
	movlw	d'3'
	movff	WREG,cpu_speed_request	; bank-independent
	; Done in ISR
	return
;=============================================================================

	END